LG M4210CE Users manual

Test Report No.: GETEC-E3-07-007

FCC Class B Certification

APPENDIX H

: USER’S MANUAL

EUT Type: 42” LCD Monitor

FCC ID: BEJM4210CE

User's guide

M4210C

Safety Precautions

Please read these safety precautions carefully before using the product.

Warning If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death.

Caution If you ignore the caution message, you may be slightly injured or the product may be damaged

Precautions in installing the Product

Warning

Keep away from heat sources like electrical heaters.

- Electrical shock, fire, malfunction or deformation may occur.

Keep the packing anti-moisture material or vinyl packing out of the reach of children.

-Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.

Do not put heavy objects on the product or sit upon it.

- If the product collapses or is dropped, you may be injured. Children must pay particular attention.

Do not leave the power or signal cable unattended on the pathway.

- The passerby can falter, which can cause electrical shock, fire, product breakdown or injury.

Install the product in a neat and dry place.

- Dust or moisture can cause electrical shock, fire or product damage.

If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the service center.

- If you continue to use without taking proper measures, electrical shock or fire can occur.

If you dropped the product or the case is broken, turn off the product and unplug the power cord.

-If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the service center.

Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the product, or inflammable objects such as paper and matches. Children must pay particular attention.

-Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord and contact the service center.

Caution

Make sure the product ventilation hole is not blocked. Install the product in a suitably wide place (more than 10cm from the wall)

- If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat.

Do not block the ventilation hole of the product by a tablecloth or curtain.

- The product can be deformed or fire can break out due to overheating inside the product.

Install the product on a flat and stable place that has no risk of dropping the product.

- If the product is dropped, you may be injured or the product may be broken.

Install the product where no EMI occurs.

Keep the product away from direct sunlight.

- The product can be damaged.

A1

Safety Precautions

Electrical Power Related Precautions

Warning

Make sure to connect the power cable to the grounded current.

- You may be electrocuted or injured.

Use the rated voltage only.

- The product can be damaged, or you may be electrocuted.

During a thunder or lightning storm, unplug the power cable or signal cable.

- You may be electrocuted or a fire can break out.

Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet. Use a power bar with a grounding terminal designed for exclusive use with the computer.

- A fire can break out due to overheating.

Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off.

- You may be electrocuted due to excess moisture.

If you don’t intend to use the product for a long time, unplug the power cable from the product.

- Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire.

Fix the power cable completely.

- If the power cable is not fixed completely, a fire can break out.

Hold the plug when pulling out the power cable. Do not bend the power cord with excessive force or put heavy objects on the power cord.

- The power line can be damaged, which may cause electric shock or fire.

Do not insert a conductor (like a metal chopstick) into one end of the power cable while the other end is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into the wall input terminal.

- You may be electrocuted.

The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation.

Caution

Do not unplug the power cord while the product is in use.

- Electrical shock can damage the product.

Precautions in Moving the Product

Warning

Make sure to turn off the product.

- You may be electrocuted or the product can be damaged.

Make sure to remove all cables before moving the product.

- You may be electrocuted or the product can be damaged.

A2

Safety Precautions

Caution

Do not shock the product when moving it.

- You may be electrocuted or the product can be damaged

Do not dispose the product-packing box. Use it when you move.

Make the panel face forward and hold it with both hands to move.

-If you drop the product, the damaged product can cause electric shock or fire. Contact with the service center for repair.

Precautions in Using the Product

Warning

Do not disassemble, repair or modify the product at your own discretion.

-Fire or electric shock accident can occur.

-Contact the service center for check, calibration or repair.

Do not spray water on the product or scrub with an inflammable substance (thinner or benzene). Fire or electric shock accident can occur

Keep the product away from water.

- Fire or electric shock accident can occur.

Caution

Do not put or store inflammable substances near the product.

- There is a danger of explosion or fire due to careless handling of the inflammable substances.

When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent scratching. Do not clean with a wet cloth.

- The water can sink into the product, which can cause electric shock or serious malfunction.

Take a rest from time to time to protect your vision.

Keep the product clean at all times.

Take a comfortable and natural position when working with a product to relax the muscles.

Take a regular break when working with a product for a long time.

Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it.

Keep proper distance from the product.

- Your vision may be impaired if you look at the product too closely.

Set the appropriate resolution and clock by referring to the User’s Manual.

- Your vision can be impaired.

Use authorized detergent only when cleaning the product. (Do not use benzene, thinner or alcohol.)

- Product can be deformed.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury.

Do not dispose of this product with general household waste.

Disposal of this product must be carried out in accordance to the regulations of your local authority.

A3

Using the Remote Control

Name of the Remote Control Buttons

•Mute button

•AV Button

•Input Select Button

(See next page)

•Menu Button

•Exit Button

•Volume Button

• Check Button

There is not a function which is supported

• ARC button

To select the image size of the screen.

• Power On/Off Button

• Sleep Button

When watching AV/S-Video/RGB/HDMI

• Component1/ Component2

The product will be automatically turned off after a certain period of time.

Press this button repetitively to select an appropriate time duration

•PSM Button

-Automatically adjusts the image. Press this button repetitively to set

the intended screen. (See A21)

• UP and Down buttons

Bring up and down direction adjustment.

• Auto Button

Automatic adjustment function (Operational for the analog signal only)

• Video Operation Button

Applicable for LG products only

A4

Using the Remote Control

• AV Button

Each time you press the Input button it will change to

AV Component1 Component2 RGB HDMI/DVI

• Input Select Button

If you press the button once, the following Input Signal

Window will appear. Select the signal type you want using thebutton.

Input

Inserting batteries into remote control.

1.Take out the battery cap.

2.Insert the batteries with correct polarity (+/-).

3. Close the battery cap.

• Dispose of used batteries in the recycle bin to prevent environmental pollution.

A5

Connecting the Speakers

* Applicable only for models that support the speakers

Use the screws to secure the speakers on the rear side of the product as shown in the below figure.

When the speaker is installed.

A6

Name and Function of the Parts

* The product image in the user’s guide could be different from the actual image.

Rear View

REMOTE	RS-232C	HDMI/DVI IN	RGB IN	AUDIO	COMPONENT IN		AV IN
CONTROL IN	(CONTROL&			(RGB/DVI)	L-AUDIO-R	VIDEO	L-AUDIO-R
	SERVICE)
	OUT		RGB OUT		1
	IN				2		AV
							OUT

REMOTE	RS-232C	HDMI/DVI IN	RGB IN	AUDIO		COMPONENT IN			AV IN
CONTROL IN	(CONTROL&			(RGB/DVI)	VIDEO		L-AUDIO-R	VIDEO	L-AUDIO-R
	SERVICE)			Y	PB	PR
	OUT		RGB OUT			1
									S-VIDEO
	IN					2			AV
									OUT

Power Connector : Connect the power cord

Wired Remote Control Port

RS-232C Serial Ports

RGB, HDMI/DVI Ports

PC Sound Jack

: Connect the audio cable to the *LINE OUT jack of the PC sound card. AV Ports

*LINE OUT

A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that the connecting terminal of the PC sound card is checked before connecting. If the Audio Out of PC sound card has only Speaker Out, reduce the PC volume.

If the Audio Out of the PC sound card supports both Speaker Out and Line Out, convert to Line Out using the card jumper of the program (Refer to the Sound Card Manual).

A7

Connecting to External Devices

When Connecting to your PC

First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable.

A When connecting with the D-Sub signal input cable.

B When connecting with the HDMI to DVI signal input cable (not included).

A

RGB IN

PC

Rear side of the product.

	MAC	PC/MAC
	Macintosh Adapter (not included)
	Use the standard Macintosh adapter since an incompatible
	adapter is available in the market. (Different signaling system)
HDMI/DVI IN
B
Rear side of the product.	(not included)
		PC

Connect the Audio cable.

AUDIO (RGB/DVI)

Rear side of the product.

PC

Connect the power cord.

Rear side of the product.

REMOTE	RS-232C	HDMI/DVI IN	RGB IN	AUDIO		COMPONENT IN			AV IN
CONTROL IN	(CONTROL&			(RGB/DVI)	VIDEO		L-AUDIO-R	VIDEO	L-AUDIO-R
	SERVICE)			Y	P	P
	OUT		RGB OUT			1
	IN					2			AV
									OUT

A8

Connecting to External Devices

1 Turn on power by pressing the power button on the product.

SOURCE	AUTO/SELECT ON/OFF
	ON/OFF

Power button

2 Turn on the PC.

Select an input signal.

Press the INPUT button on the remote control to select the input signal.

INPUT SET

Or, press the SOURCE button at the front side of the product.

SOURCE AUTO/SELECT

AWhen connecting with a D-Sub signal input cable.

•Select RGB : 15-pin D-Sub analog signal.

BWhen connecting with a HDMI to DVI signal input cable.

•Select HDMI/DVI : HDMI to DVI Digital signal.

Input		Input

• How to connect to two computers.

Note Connect the signal cables (HDMI to DVI and D-Sub) to each computer. Press the INPUT button in a remote control to select the computer to use.

•Directly connect to a grounded power outlet on the wall or a power bar with a ground wire.

A9

Connecting to External Devices

Watching RGB Outputs

Use this function when displaying ANALOG RGB inputs of a PC to the other product.

•To use different products connected to each other

Connect one end of the signal input cable(15-pin D-Sub Signal Cable) to the RGB OUT connector of product 1 and connect the other end to the RGB IN connector of other products.

15-pin D-Sub Signal Cable

RGB IN	RGB IN	RGB IN	RGB IN
RGB OUT	RGB OUT	RGB OUT	RGB OUT

PC

PC

Product 1

Product 2

Product 3

Product 4

Note

• When multi-connecting in/out cascade format, cables to be less damaged are recommended. We recommend that you should use cable distributor.

A10

Connecting to External Devices

When watching VCR / DVD

Connect the video cable as shown in the below figure and then connect the power cord (See page A9).

AWhen connecting with a BNC cable.

•Connect the input terminal with a proper color match.

Product

AV IN

VIDEO L-AUDIO-R

S-VIDEO

AV

OUT

Audio Cable BNC Cable (not included)

(not included)

BWhen connecting with a S-Video cable.

• Connect to the S-Video input terminal to watch high image quality movies.

Product

AV IN

VIDEO L-AUDIO-R

S-VIDEO

AV

OUT

Audio Cable (not included)

S-Video Cable

(not included)

W

R

VCR/DVD Receiver			VCR/DVD Receiver

Select an input signal.

Press the INPUT button on the remote control to select the input signal.

INPUT SET

Input

Or, press the SOURCE button at the front side of the product.

SOURCE	AUTO/SELECT

A When connecting with an BNC cable.

• Select AV.

BWhen connecting with an S-Video cable.

•Select AV.

Note	• In case the BNC cable is connected simultaneously as S-Video cable is connected, S-Video cable is
	first.

A11

Connecting to External Devices

When watching HDTV/DVD(480p/576p/720p/1080i/480i/576i)

Connect the video/audio cable as shown in the below figure and then, connect the power cord (See page A9).

• Connect the input terminal with a proper color match.

A		Product	B		Product
		COMPONENT IN
Y	VIDEO		L-AUDIO-R		COMPONENT IN
	PB	PR		VIDEO
						L-AUDIO-R
		1	Y	PB	PR
					1
		2
					2

BNC Cable

Audio Cable

BNC Cable

Audio Cable

(not included)

(not included)

(not included)

(not included)

HDTV Receiver

HDTV Receiver

Select an input signal.

Press the INPUT button on the remote control to select the input signal.

INPUT SET

Or, press the SOURCE button at the front side of the product.

SOURCE AUTO/SELECT

A • Select Component 1

B • Select Component 2

Input		Input

A12

Connecting to External Devices

When watching HDMI/DVI/RGB from the VCR/DVD/Set-top Box (480p/576p/720p/1080i)

Connect the video/audio cable as shown in the below figure and then connect the power cord (See page A9).

A		Product		Product					Product
	HDMI/DVI IN	RGB IN	AUDIO	HDMI/DVI IN	RGB IN	AUDIO	B	HDMI/DVI IN	RGB IN	AUDIO
			(RGB/DVI)
						(RGB/DVI)				(RGB/DVI)
		RGB OUT			RGB OUT

	HDMI to DVI	RCA-PC		D-Sub Signal	RCA-PC
	Signal Cable		HDMI Signal Cable
		Audio Cable		Cable	Audio Cable
	(not included)		(not included)

VCR/DVD/Set-top Box

VCR/DVD/Set-top Box

VCR/DVD/Set-top Box

Select an input signal.

Press the INPUT button on the remote control to select the input signal.

INPUT	SET

Or, press the SOURCE button at the front side of the product.

SOURCE AUTO/SELECT

AWhen connecting with a HDMI to DVI signal input cable. When connecting with a HDMI signal input cable.

•Select HDMI/DVI

BWhen connecting with a D-Sub signal input cable.

•Select RGB

Input			Input

A13