LG M227WAP-PM, M197WAP-PT, M227WAP-PT Owner’s Manual
ENGLISH
OWNER’S MANUAL
MONITOR TV
Please read this manual carefully before operating
your set and retain it for future reference.
MONITOR TV MODELS
M197WAP
M227WAP
M237WAP
www.lge.com
CONTENTS
CONTENTS
PREPARATION
FRONT PANEL CONTROLS ..............................4
BACK PANEL INFORMATION ............................5
STAND INSTALLATION
<M197WAP/M227WAP> ...................................6
<M237WAP> .....................................................7
DETACHING STAND
<M197WAP/M227WAP> ...................................8
<M237WAP> .....................................................9
WALL MOUNT: HORIZONTAL INSTALLATION ....10
DESKTOP PEDESTAL INSTALLATION ...........11
POSITIONING YOUR DISPLAY .......................11
LOCATION ........................................................12
KENSINGTON SECURITY SYSTEM ...............13
ANTENNA CONNECTION ................................14
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUP
When connecting with a component cable .....15
Connecting a set-top box with a HDMI cable .16
DVD SETUP
Connecting with a component cable ..............17
Connecting with a HDMI cable .......................18
VCR SETUP
Connecting with a RF cable ............................19
Connecting with a RCA cable .........................19
OTHER A/V SOURCE SETUP .........................20
PC SETUP
When connecting with a D-sub 15 pin cable ........21
BACK COVER FOR WIRE ARRANGEMENT ..22
SUPPORTED DISPALY RESOLUTION ...........23
INSTALLATION GUIDE .....................................26
PROGRAMME SELECTION .............................26
VOLUME ADJUSTMENT ..................................26
ON SCREEN MENUS SELECTION AND
ADJUSTMENT ..................................................27
AUTO PROGRAMME TUNING ........................28
MANUAL PROGRAMME TUNING ...................29
FINE TUNING ...................................................30
ASSIGNING A STATION NAME .......................31
PROGRAMME EDIT .........................................32
FAVOURITE PROGRAMME .............................33
SELECTING THE PROGRAMME LIST ............34
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO)CONTROL ..35
PRESET PICTURE SETTINGS ........................36
MANUAL PICTURE ADJUSTMENT .................37
PICTURE IMPROVEMENT TECHNOLOGY ....38
PICTURE RESET .............................................40
SCREEN SETUP
AUTO CONFIGURE
(RGB [PC] mode only) ....................................41
MANUAL CONFIGURE
(Adjustment for screen Position) ....................42
INITIALIZING
(Reset to original factory settings) ..................43
SELECTING RESOLUTION .............................44
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS
- SOUND MODE ............................................45
SOUND SETTING ADJUSTMENT
WATCHING TV / PROGRAMME
CONTROL
REMOTE CONTROL KEY FUNCTIONS ..........24
TURNING ON THE TV .....................................26
- USER MODE ...............................................46
AUTO VOLUME LEVELER ...............................47
BALANCE ..........................................................48
AUDIO RESET ..................................................49
I/II
STEREO / DUAL RECEPTION ......................50
2
NICAM RECEPTION ......................................51
SPEAKER SOUND OUTPUT SELECTION ...51
TIME SETTING
CLOCK SETUP .................................................52
AUTO ON/OFF TIMER SETTING ....................53
SLEEP TIMER SETTING ..................................54
AUTO SHUT-OFF SETTING ............................55
OPTION SETTING
ON-SCREEN MENU LANGUAGE SELECTION ...56
KEY LOCK ........................................................57
DDC-CI(Only RGB) ...........................................58
POWER INDICATOR ........................................59
MODE SETTING ...............................................60
FACTORY RESET ............................................61
M227WAP .......................................................69
M237WAP .......................................................70
CONTENTS
TELETEXT
SWITCH ON/OFF .............................................62
SIMPLE TEXT ...................................................62
SWITCH ON/OFF .............................................63
FASTEXT ..........................................................63
SPECIAL TELETEXT FUNCTIONS ..................64
APPENDIX
TROUBLESHOOTING ......................................65
MAINTENANCE ................................................67
PRODUCT SPECIFICATIONS
M197WAP .......................................................68
3
PREPARATION
FRONT PANEL CONTROLS
■ This is a simplified representation of the front panel. The image shown may be somewhat different
from your set.
PREPARATION
INPUT
INPUT Button
MENU
MENU Button
OK Button
VOL PROK
VOLUME Buttons
PROGRAMME Buttons
Power Button
Headphone Jack
4
BACK PANEL INFORMATION
■ This is a simplified representation of the back panel. The image shown may be somewhat different
from your set.
<M197WAP/M227WAP> <M237WAP>
1 1
2 2
3 4 7 8
AV IN
VIDEO AUDIO
(MONO)
R
L
HDMI IN
RGB IN (PC)
Y
AUDIO IN
(RGB)
VIDEO
P
B
P
COMPONENT IN
L
AUDIO
R
R
ANTENNA/
CABLE IN
PREPARATION
5 6
1
POWER CORD SOCKET
This set operates on AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the set on DC power.
AUDIO OUTPUT
2
Connect the audio from a Headphone Jack.
HDMI INPUT
3
Connect a HDMI signal to HDMI IN.
Or DVI (VIDEO) signal to HDMI IN with DVI to
HDMI cable.
RGB/DVI AUDIO INPUT
4
Connect the audio from a PC.
5
RGB INPUT (PC)
Connect the output from a PC.
COMPONENT INPUT
6
Connect a component video/audio device to
these jacks.
AV(AUDIO/VIDEO) INPUT
7
Connect audio/video output from an external
device to these jacks.
ANTENNA INPUT
8
Connect over-the-air signals to this jack.
5
PREPARATION
STAND INSTALLATION
■ The image shown may be somewhat different from your set.
Carefully place the product screen side down on a
1
PREPARATION
cushioned surface that will protect product and
screen from damage.
Insert the stand base into the product.
2
<M197WAP/M227WAP>
Use a coin on the bottom of the stand base and turn
3
the screw clockwise to tighten.
6
STAND INSTALLATION
■ The image shown may be somewhat different from your set.
Carefully place the product screen side down on a
1
cushioned surface that will protect product and
screen from damage.
Insert the stand base into the product.
2
<M237WAP>
PREPARATION
Use a coin on the bottom of the stand base and turn
3
the screw clockwise to tighten.
7
PREPARATION
DETACHING STAND
■ The image shown may be somewhat different from your set.
<M197WAP/M227WAP>
PREPARATION
Place the set screen side down on a
1 2
cushion or soft cloth.
Turn the screw by using a coin.
3
4
Detach the monitor to the Stand Base by
turning the screw to the left.
Pull the stand base.
5
8
DETACHING STAND
■ The image shown may be somewhat different from your set.
<M237WAP>
Place the set screen side down on a
1 2
cushion or soft cloth.
Turn the screw by using a coin.
3
4
Detach the monitor to the Stand Base by
turning the screw to the left.
Pull the stand base.
PREPARATION
5
9
PREPARATION
WALL MOUNT: HORIZONTAL INSTALLATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation
instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
PREPARATION
10 cm
10 cm
10 cm
10 cm
10 cm
If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.
1. Be sure to use screws and a wall mount that meet VESA standards.
2. Using screws longer than those recommended might damage the product.
3. Using screws that do not meet VESA standards might either damage the product or result in it coming
away from the wall. We will not be held responsible for any damage resulting from failure to follow these
instructions.
4. VESA compatible only with respect to screw mounting interface dimensions and mounting screw specifications
5. Please use VESA standard as below.
5-1) 784.8 mm (30.9 inch) and under
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mm
5-2) 787.4 mm (31.0 inch) and above
* Please use VESA standard wall mount pad and screws.
10
< Screw Mounting Interface Dimension >
M197WAP : 100 mm x 100 mm hole spacing
M227WAP : 100 mm x 100 mm hole spacing
M237WAP : 75 mm x 75 mm hole spacing
Wall Mount Pad
DESKTOP PEDESTAL INSTALLATION
INPUT
MENU
VOL PROK
For proper ventilation, allow a clearance of 10 cm on each side and from the wall.
10 cm
10 cm
POSITIONING YOUR DISPLAY
■ The image shown may be somewhat different from your set.
Adjust the position of the panel in various ways for maximum comfort.
10 cm
10 cm
PREPARATION
* Tilt range
-6° to -2° 12° to 18°
11
PREPARATION
LOCATION
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to
expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a
position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
PREPARATION
Warning:
When adjusting the angle of the screen, do not put your finger(s)
in between the head of the monitor and the stand body.
You can hurt your finger(s).
12
KENSINGTON SECURITY SYSTEM
- The product is equipped with a Kensington Security System connector on the back panel. Connect the
Kensington Security System cable as shown below.
- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided
with the Kensington Security System.
For further information, contact http://www.kensington.com, the internet homepage of the Kensington
company. Kensington sells security systems for expensive electronic equipment such as notebook
PCs and LCD projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a. If the product feels cold to the touch, there may be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with product.
b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the monitor’s performance.
c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
PREPARATION
<M237WAP><M197WAP/ M227WAP >
13
PREPARATION
■ To prevent damage do not connect to the mains outlet until all connections are made between the devices.
ANTENNA CONNECTION
■ For optimum picture quality, adjust antenna direction.
■ An antenna cable and converter are not supplied.
PREPARATION
<M237WAP><M197WAP/ M227WAP >
Wall
Antenna
Socket
Outdoor
Antenna
Multi-family Dwellings / Apartments
(Connect to wall antenna socket)
RF Coaxial Wire (75 Ω)
Single-family Dwellings / Houses
(Connect to wall jack for outdoor antenna)
ANTENNA/
CABLE IN
14
Antenna
UHF
Signal
Amplifier
VHF
ANTENNA/
CABLE IN
■ In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.
■ If signal needs to be split for two sets, use an antenna signal splitter for connection.
EXTERNAL EQUIPMENT SETUP
ANTENNA/
CABLE IN
■ To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
■ The image shown may be somewhat different from your set.
HD RECEIVER SETUP
When connecting with a component cable
Connect the video outputs (Y, PB, PR) of the digital
1
set-top box to the COMPONENT IN VIDEO jacks on
the TV.
Connect the audio output of the digital set-top box
2
to the COMPONENT IN AUDIO jacks on the TV.
Turn on the digital set-top box.
3
(Refer to the owner’s manual for the digital set-top
box.)
Select Component input source using the INPUT but-
4
ton on the remote control
Signal Component
480i / 576i O
HDMI IN
Y
AUDIO IN
(RGB/DVI)
VIDEO
P
B
AV IN
VIDEO AUDIO
(MONO)
P
R
L
COMPONENT IN
L
AUDIO
R
EXTERNAL EQUIPMENT SETUP
R
480p / 576p O
720p O
1080i / 1080p O
15
EXTERNAL EQUIPMENT SETUP
AUDIO IN
(RGB/DVI)
VIDEO
VIDEO AUDIO
(MONO)
AUDIO
Y
P
B
P
R
L
R
HDMI IN
ANTENNA/
CABLE IN
L
R
RGB IN (PC)
COMPONENT IN
AV IN
O
R
ANTENNA/
CABLE IN
!
EXTERNAL EQUIPMENT SETUP
Connecting a set-top box with a HDMI cable
Connect the HDMI output of the digital set-top box to
1
the HDMI IN jack on the TV.
Select HDMI input source using the INPUT button on
2
the remote control.
Turn on the digital set-top box.
3
(Refer to the owner’s manual for the digital set-top
box.)
NOTE
► TV can receive the video and audio signal simultaneously-
with using a HDMI cable.
► If the digital set-top box supports Auto HDMI function, the
output resolution of the source device will be automatically
TV to 1920 x 1080p.
► If the digital set-top box player does not support Auto HDMI,
you need to TV the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1920 x 1080p .
HDMI IN
RGB IN (PC)
Y
AUDIO IN
(RGB/DVI)
VIDEO
PB
AV IN
VIDEO AUDI
(MONO)
PR
L
COMPONENT IN
L
AUDIO
R
► We recommend less than 10 m for HDMI cable.
Signal HDMI
480i / 576i O
480p / 576p O
720p O
1080i / 1080p O
16
DVD SETUP
ANTENNA/
CABLE IN
Connecting with a component cable
Connect the video outputs (Y, PB, PR) of the DVD to
1
the COMPONENT IN VIDEO jacks on the TV.
HDMI IN
AUDIO IN
(RGB/DVI)
AV IN
VIDEO AUDIO
(MONO)
L
R
Connect the audio outputs of the DVD to the
2
COMPONENT IN AUDIO jacks on the TV.
Turn on the DVD player, insert a DVD.
3
Select Component input source using the INPUT but-
4
ton on the remote control.
Refer to the DVD player’s manual for operating
5
instructions.
Component Input ports
To achieve better picture quality, connect a DVD player to
the component input ports as shown below.
VIDEO
P
R
P
B
Y
COMPONENT IN
AUDIO
R
L
EXTERNAL EQUIPMENT SETUP
Component ports on the TV Y P
Y P
Y P-Y R-Y
Y Cb Cr
Video output ports
on DVD player
Y Pb Pr
B
B
P
R
P
R
17
EXTERNAL EQUIPMENT SETUP
AUDIO IN
(RGB/DVI)
VIDEO
VIDEO AUDIO
(MONO)
AUDIO
Y
P
B
P
R
L
R
HDMI IN
ANTENNA/
CABLE IN
L
R
RGB IN (PC)
COMPONENT IN
AV IN
O
R
ANTENNA/
CABLE IN
!
EXTERNAL EQUIPMENT SETUP
Connecting with a HDMI cable
Connect the HDMI output of the DVD to the HDMI IN
1
jack on the TV.
Select HDMI input source using the INPUT button on
2
the remote control.
Refer to the DVD player’s manual for operating
3
instructions.
NOTE
► TV can receive the video and audio signal simultaneously-
with using a HDMI cable.
► If the digital set-top box supports Auto HDMI function, the
output resolution of the source device will be automatically
TV to 1920 x 1080p.
► If the digital set-top box player does not support Auto HDMI,
you need to TV the output resolution appropriately.
► To get the best picture quality, adjust the output resolu-
tion of the source device to 1920 x 1080p.
► We recommend less than 10 m for HDMI cable.
HDMI IN
RGB IN (PC)
Y
AUDIO IN
(RGB/DVI)
VIDEO
PB
AV IN
VIDEO AUDI
(MONO)
PR
L
COMPONENT IN
L
AUDIO
R
18
VCR SETUP
HDMI IN
AUDIO IN
(RGB/DVI)
VIDEO AUDIO
(MONO)
L
R
AV IN
VIDEO
AUDIO
Y
PB
PR
L
R
COMPONENT IN
RGB IN (PC)
ANTENNA/
CABLE IN
L
R
S-VIDEO
VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
■ To avoid picture noise (interference), allow adequate distance between the VCR and TV.
Connecting with a RF cable
Connect the ANT OUT socket of the VCR
1
to the ANTENNA IN socket on the TV.
Connect the antenna cable to the ANT IN
2
socket of the VCR.
Press the PLAY button on the VCR and
3
match the appropriate programme
between the TV and VCR for viewing.
Connecting with a RCA cable
Connect the AUDIO / VIDEO jacks between TV and
1
VCR. Match the jack colours (Video = yellow, Audio
Left = white, and Audio Right = red)
Insert a video tape into the VCR and press PLAY on
2
the VCR.
(Refer to the VCR owner’s manual.)
Select AV input source using the INPUT button on the
3
remote control.
AV IN
VIDEO AUDIO
(MONO)
L
AUDIO
R
L
R
ANTENNA/
CABLE IN
HDMI IN
RGB IN (PC)
(RGB/DVI)
Y
AUDIO IN
VIDEO
PB
S-VIDEO VIDEO
ANT OUT
OUTPUT
ANT IN
SWITCH
AV IN
VIDEO AUDIO
(MONO)
PR
L
COMPONENT IN
L
AUDIO
L
EXTERNAL EQUIPMENT SETUP
R
R
ANTENNA/
CABLE IN
R
S-VIDEO
VIDEO
OUTPUT
SWITCH
L
R
ANT IN
ANT OUT
19
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
Connect the AUDIO/VIDEO jacks between
1
TV and external equipment. Match the jack
colours.
(Video = yellow, Audio Left = white, and
Audio Right = red)
Select AV input source using the INPUT but-
EXTERNAL EQUIPMENT SETUP
2
ton on the remote control.
If connected to AV IN, select AV input
source.
Operate the corresponding external equip-
3
ment.
Refer to external equipment operating guide.
HDMI IN
RGB IN (PC)
Y
AUDIO IN
(RGB/DVI)
VIDEO
PB
AV IN
VIDEO AUDIO
(MONO)
PR
L
COMPONENT IN
VIDEO
L
AUDIO
R
L R
R
ANTENNA/
CABLE IN
20
PC SETUP
ANTENNA/
CABLE IN
!
When using the remote control, aim it at the remote control sensor on the TV.
When connecting with a D-sub 15 pin cable
Connect the signal cable from the monitor output socket
1
of the PERSONAL COMPUTER to the PC input socket
of the set.
Connect the audio cable from the PC to the AUDIO IN
2
(RGB) sockets of the set.
3
Press the INPUT button to select RGB PC.
Switch on the PC, and the PC screen appears on the set.
4
The set can be operated as a PC monitor.
HDMI IN
RGB IN (PC)
RGB OUTPUT
Y
AUDIO IN
(RGB)
VIDEO
PB
AUDIO
AV IN
VIDEO AUDIO(MONO)
PR
L
COMPONENT IN
L
AUDIO
R
R
EXTERNAL EQUIPMENT SETUP
NOTE
► User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard
compliance for the product.
21
EXTERNAL EQUIPMENT SETUP
BACK COVER FOR WIRE ARRANGEMENT
Tie cables together with a cable management as shown in the illustration.
<M197WAP/ M227WAP >
EXTERNAL EQUIPMENT SETUP
<M237WAP>
22
Loading...