<![endif]>ENGLISH
OWNER’S MANUAL
MONITOR TV
Please read this manual carefully before operating your set and retain it for future reference.
MONITOR TV MODELS
M197WAP
M227WAP
M237WAP
www.lge.com
CONTENTS
<![endif]>CONTENTS
PREPARATION |
|
FRONT PANEL CONTROLS............................... |
4 |
BACK PANEL INFORMATION............................ |
5 |
STAND INSTALLATION |
|
<M197WAP/M227WAP>................................... |
6 |
<M237WAP>..................................................... |
7 |
DETACHING STAND |
|
<M197WAP/M227WAP>................................... |
8 |
<M237WAP>..................................................... |
9 |
WALLMOUNT: HORIZONTALINSTALLATION..... |
10 |
DESKTOP PEDESTAL INSTALLATION............ |
11 |
POSITIONING YOUR DISPLAY........................ |
11 |
LOCATION......................................................... |
12 |
KENSINGTON SECURITY SYSTEM................ |
13 |
ANTENNA CONNECTION................................ |
14 |
EXTERNAL EQUIPMENT SETUP |
|
HD RECEIVER SETUP |
|
When connecting with a component cable..... |
15 |
Connecting a set-top box with a HDMI cable.16 |
|
DVD SETUP |
|
Connecting with a component cable............... |
17 |
Connecting with a HDMI cable........................ |
18 |
VCR SETUP |
|
Connecting with a RF cable............................ |
19 |
Connecting with a RCA cable.......................... |
19 |
OTHER A/V SOURCE SETUP.......................... |
20 |
PC SETUP |
|
When connecting with a D-sub 15 pin cable......... |
21 |
BACK COVER FOR WIRE ARRANGEMENT... |
22 |
SUPPORTED DISPALY RESOLUTION............ |
23 |
WATCHING TV / PROGRAMME |
|
CONTROL |
|
REMOTE CONTROL KEY FUNCTIONS.......... |
24 |
TURNING ON THE TV...................................... |
26 |
INSTALLATION GUIDE..................................... |
26 |
PROGRAMME SELECTION............................. |
26 |
VOLUME ADJUSTMENT.................................. |
26 |
ON SCREEN MENUS SELECTION AND |
|
ADJUSTMENT................................................... |
27 |
AUTO PROGRAMME TUNING......................... |
28 |
MANUAL PROGRAMME TUNING.................... |
29 |
FINE TUNING.................................................... |
30 |
ASSIGNING A STATION NAME........................ |
31 |
PROGRAMME EDIT.......................................... |
32 |
FAVOURITE PROGRAMME............................. |
33 |
SELECTING THE PROGRAMME LIST............ |
34 |
PICTURE CONTROL |
|
PICTURE SIZE (ASPECT RATIO)CONTROL..35 |
|
PRESET PICTURE SETTINGS........................ |
36 |
MANUAL PICTURE ADJUSTMENT.................. |
37 |
PICTURE IMPROVEMENT TECHNOLOGY..... |
38 |
PICTURE RESET.............................................. |
40 |
SCREEN SETUP |
|
AUTO CONFIGURE |
|
(RGB [PC] mode only)..................................... |
41 |
MANUAL CONFIGURE |
|
(Adjustment for screen Position)..................... |
42 |
INITIALIZING |
|
(Reset to original factory settings)................... |
43 |
SELECTING RESOLUTION.............................. |
44 |
SOUND & LANGUAGE CONTROL |
|
PRESET SOUND SETTINGS |
|
- SOUND MODE............................................ |
45 |
SOUND SETTING ADJUSTMENT |
|
- USER MODE............................................... |
46 |
AUTO VOLUME LEVELER............................... |
47 |
BALANCE.......................................................... |
48 |
AUDIO RESET.................................................. |
49 |
I/II |
|
STEREO / DUAL RECEPTION....................... |
50 |
2
NICAM RECEPTION....................................... |
51 |
M227WAP........................................................ |
69 |
SPEAKER SOUND OUTPUT SELECTION.... |
51 |
M237WAP........................................................ |
70 |
TIME SETTING |
|
CLOCK SETUP................................................. |
52 |
AUTO ON/OFF TIMER SETTING..................... |
53 |
SLEEP TIMER SETTING.................................. |
54 |
AUTO SHUT-OFF SETTING............................. |
55 |
OPTION SETTING |
|
ON-SCREEN MENU LANGUAGE SELECTION.... |
56 |
KEY LOCK......................................................... |
57 |
DDC-CI(Only RGB)............................................ |
58 |
POWER INDICATOR......................................... |
59 |
MODE SETTING............................................... |
60 |
FACTORY RESET............................................. |
61 |
TELETEXT |
|
SWITCH ON/OFF.............................................. |
62 |
SIMPLE TEXT.................................................... |
62 |
SWITCH ON/OFF.............................................. |
63 |
FASTEXT........................................................... |
63 |
SPECIAL TELETEXT FUNCTIONS.................. |
64 |
APPENDIX |
|
TROUBLESHOOTING....................................... |
65 |
MAINTENANCE................................................. |
67 |
PRODUCT SPECIFICATIONS |
|
M197WAP........................................................ |
68 |
<![endif]>CONTENTS
3
■■ This is a simplified representation of the front panel. The image shown may be somewhat different from your set.
<![endif]>PREPARATION
<![endif]>VO L OK MEN UINPU T
<![if ! IE]><![endif]>PR
INPUT Button
MENU Button
OK Button
VOLUME Buttons
PROGRAMME Buttons
Power Button
Headphone Jack
4
■■ This is a simplified representation of the back panel. The image shown may be somewhat different from your set.
<M197WAP/M227WAP> <M237WAP>
1 |
|
|
1 |
|
|
|
2 |
|
|
2 |
|
|
|
3 |
|
4 |
7 |
|
|
8 |
|
|
AUDIO IN |
|
AV IN |
|
|
|
|
VIDEO |
|
AUDIO |
|
|
HDMI IN |
|
(RGB) |
(MONO) L |
R |
||
|
|
|
|
|
|
|
|
|
VIDEO |
|
AUDIO |
ANTENNA/ |
|
|
Y |
PB |
PR |
L |
R |
CABLE IN |
RGB IN (PC) |
|
|||||
|
COMPONENT IN |
|
|
|||
|
|
|
|
1 |
5 |
6 |
5 |
|
POWER CORD SOCKET |
|
RGB INPUT (PC) |
||
|
This set operates on AC power. The voltage is |
|
Connect the output from a PC. |
|
|
indicated on the Specifications page. Never |
|
|
|
|
attempt to operate the set on DC power. |
6 |
COMPONENT INPUT |
|
|
|
|
||
2 |
AUDIO OUTPUT |
|
|
Connect a component video/audio device to |
|
|
these jacks. |
||
|
Connect the audio from a Headphone Jack. |
|
|
|
3 |
HDMI INPUT |
|
7 |
AV(AUDIO/VIDEO) INPUT |
|
|
Connect audio/video output from an external |
||
|
Connect a HDMI signal to HDMI IN. |
|
|
device to these jacks. |
|
Or DVI (VIDEO) signal to HDMI IN with DVI to |
|
|
|
|
HDMI cable. |
|
8 |
ANTENNA INPUT |
4 |
RGB/DVI AUDIO INPUT |
|
|
Connect over-the-air signals to this jack. |
|
|
|
Connect the audio from a PC.
<![endif]>PREPARATION
5
<![endif]>PREPARATION
PREPARATION
<M197WAP/M227WAP>
■ ■ The image shown may be somewhat different from your set.
1Carefully place the product screen side down on a cushioned surface that will protect product and
screen from damage.
2 Insert the stand base into the product.
3Use a coin on the bottom of the stand base and turn the screw clockwise to tighten.
6
STAND INSTALLATION
■■ The image shown may be somewhat different from your set.
1 Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage.
2 Insert the stand base into the product.
3Use a coin on the bottom of the stand base and turn the screw clockwise to tighten.
<M237WAP>
<![if ! IE]><![endif]>PREPARATION
7
<![endif]>PREPARATION
PREPARATION
<M197WAP/M227WAP>
■ ■ The image shown may be somewhat different from your set.
1 |
Place the set screen side down on a |
2 |
Detach the monitor to the Stand Base by |
|
cushion or soft cloth. |
|
turning the screw to the left. |
3 Turn the screw by using a coin. |
4 Pull the stand base. |
5
8
<M237WAP>
DETACHING STAND
■ ■ The image shown may be somewhat different from your set.
1Place the set screen side down on a cushion or soft cloth.
2Detach the monitor to the Stand Base by turning the screw to the left.
<![if ! IE]><![endif]>PREPARATION
3 Turn the screw by using a coin. |
4 Pull the stand base. |
5
9
PREPARATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.
<![if ! IE]> <![endif]>PREPARATION |
|
10 cm |
10 cm |
|
|
||
|
|
|
|
|
10 cm |
|
10 cm |
|
|
10 cm |
|
If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.
1.Be sure to use screws and a wall mount that meet VESA standards.
2.Using screws longer than those recommended might damage the product.
3.Using screws that do not meet VESA standards might either damage the product or result in it coming away from the wall. We will not be held responsible for any damage resulting from failure to follow these instructions.
4.VESA compatible only with respect to screw mounting interface dimensions and mounting screw specifications
5.Please use VESA standard as below. 5-1) 784.8 mm (30.9 inch) and under
* Wall Mount Pad Thickness : 2.6 mm
*Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mm 5-2) 787.4 mm (31.0 inch) and above
*Please use VESA standard wall mount pad and screws.
<Screw Mounting Interface Dimension >
M197WAP : 100 mm x 100 mm hole spacing
M227WAP : 100 mm x 100 mm hole spacing
M237WAP : 75 mm x 75 mm hole spacing
Wall Mount Pad
10
For proper ventilation, allow a clearance of 10 cm on each side and from the wall.
10 cm
10 cm |
10 cm |
10 cm |
<![endif]>PREPARATION
■ ■ The image shown may be somewhat different from your set. Adjust the position of the panel in various ways for maximum comfort.
* Tilt range
-6° to -2° 12° to 18°
11
PREPARATION
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
<![endif]>PREPARATION
Warning:
When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body.
You can hurt your finger(s).
12
-The product is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below.
-For detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System.
For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a.If the product feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with product.
b.Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor’s performance.
c.Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
<![endif]>PREPARATION
<M197WAP/ M227WAP > |
<M237WAP> |
13
PREPARATION
<![endif]>PREPARATION
■ ■ To prevent damage do not connect to the mains outlet until all connections are made between the devices.
■■ For optimum picture quality, adjust antenna direction.
■■ An antenna cable and converter are not supplied.
<M197WAP/ M227WAP > <M237WAP>
Wall |
Multi-family Dwellings / Apartments |
ANTENNA/ |
|
(Connect to wall antenna socket) |
|||
CABLE IN |
|||
Antenna |
|
|
|
Socket |
|
|
RF Coaxial Wire (75 Ω)
Outdoor
Antenna Single-family Dwellings / Houses
(Connect to wall jack for outdoor antenna)
UHF |
ANTENNA/ |
|
Antenna |
CABLE IN |
|
Signal |
||
|
||
|
Amplifier |
VHF
■■ In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.
■■ If signal needs to be split for two sets, use an antenna signal splitter for connection.
14
■■ Toavoiddamaginganyequipment,neverpluginanypowercordsuntilyouhavefinishedconnectingallequipment.
■■ The image shown may be somewhat different from your set.
1Connect the video outputs (Y, PB, PR) of the digital set-top box to the COMPONENT IN VIDEO jacks on the TV.
2Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO jacks on the TV.
|
|
AUDIO IN |
|
AV IN |
|
|
|
|
VIDEO |
|
AUDIO |
|
|
HDMI IN |
|
(RGB/DVI) |
(MONO) L |
R |
||
|
|
|
|
|
|
|
|
|
VIDEO |
|
AUDIO |
ANTENN |
|
|
Y |
PB |
PR |
L |
R |
CABLE I |
GB IN (PC) |
|
|||||
|
COMPONENT IN |
|
|
|||
|
|
|
|
3Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
4Select Component input source using the INPUT button on the remote control
<![endif]>SETUP EQUIPMENT EXTERNAL
Signal |
Component |
|
|
|
|
|
|
|
|
|
|
|
||
480i |
/ 576i |
O |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
480p |
/ 576p |
O |
|
|
|
|
|
|
|
|
|
|
|
|
720p |
O |
|
|
|
|
|
|
|
|
|
|
|
||
1080i / 1080p |
O |
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
15
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
Connect the HDMI output of the digital set-top box to
1the HDMI IN jack on the TV.
2Select HDMI input source using the INPUT button on the remote control.
Turn on the digital set-top box.
3(Refer to the owner’s manual for the digital set-top box.)
|
AUDIO IN |
|
|
AV IN |
|
|
|
VIDEO |
|
AUDI |
|
HDMI IN |
(RGB/DVI) |
|
(MONO) L |
||
|
|
|
|
|
|
|
VIDEO |
|
AUDIO |
||
Y |
PB |
PR |
|
L |
R |
|
|
COMPONENT IN |
|
! NOTE
►►TV can receive the video and audio signal simultaneouslywith using a HDMI cable.
►►If the digital set-top box supports Auto HDMI function, the output resolution of the source device will be automatically TV to 1920 x 1080p.
►►Ifthedigitalset-topboxplayerdoesnotsupportAutoHDMI, you need to TV the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1920 x 1080p .
► ►We recommend less than 10 m for HDMI cable.
Signal |
HDMI |
|
480i |
/ 576i |
O |
480p |
/ 576p |
O |
720p |
O |
|
1080i / 1080p |
O |
|
|
|
|
16
1 |
Connect the video outputs (Y, PB, PR) of the DVD to |
|
|
|
|
|
|
|
|
the COMPONENT IN VIDEO jacks on the TV. |
|
|
AUDIO IN |
VIDEO |
AV IN |
AUDIO R |
|
|
|
HDMI IN |
|
(RGB/DVI) |
(MONO) L |
|
||
|
|
|
|
|
|
|
|
|
2 |
Connect the audio outputs of the DVD to the |
|
|
VIDEO |
AUDIO |
ANTENN |
||
|
COMPONENT IN AUDIO jacks on the TV. |
|
Y |
PB |
PR |
L |
R |
CABLE I |
|
GB IN (PC) |
|
||||||
|
|
|
||||||
|
|
|
|
COMPONENT IN |
|
|
||
|
|
|
|
|
|
|
||
3 |
Turn on the DVD player, insert a DVD. |
|
|
|
|
|
|
|
4 |
Select Component input source using the INPUT but- |
|
|
|
|
|
|
|
|
ton on the remote control. |
|
|
|
|
|
|
|
5 Refer to the DVD player’s manual for operating instructions.
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV |
Y |
PB |
PR |
|
|
|
|
|
|
|
|
|
Y |
PB |
PR |
Video output ports |
Y |
P-Y |
R-Y |
|
|
|
|
on DVD player |
Y |
Cb |
Cr |
|
|||
|
Y |
Pb |
Pr |
|
|
|
|
<![endif]>SETUP EQUIPMENT EXTERNAL
17
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
1Connect the HDMI output of the DVD to the HDMI IN jack on the TV.
2Select HDMI input source using the INPUT button on the remote control.
3Refer to the DVD player’s manual for operating instructions.
|
AUDIO IN |
|
|
AV IN |
|
|
|
VIDEO |
|
AUDI |
|
HDMI IN |
(RGB/DVI) |
|
(MONO) L |
||
|
|
|
|
|
|
|
VIDEO |
|
AUDIO |
||
Y |
PB |
PR |
|
L |
R |
|
|
COMPONENT IN |
|
! NOTE
►►TV can receive the video and audio signal simultaneouslywith using a HDMI cable.
►►If the digital set-top box supports Auto HDMI function, the output resolution of the source device will be automatically TV to 1920 x 1080p.
►►Ifthedigitalset-topboxplayerdoesnotsupportAutoHDMI, you need to TV the output resolution appropriately.
►►To get the best picture quality, adjust the output resolution of the source device to 1920 x 1080p.
►►We recommend less than 10 m for HDMI cable.
18
■ ■ Toavoidpicturenoise(interference),allowadequatedistancebetweentheVCRandTV.
1Connect the ANT OUT socket of the VCR to the ANTENNA IN socket on the TV.
2Connect the antenna cable to the ANT IN socket of the VCR.
|
AV IN |
|
|
|
|
|
|
VIDEO |
(MONO) L |
AUDIO |
R |
|
|
|
|
|
AUDIO |
ANTENNA/ |
|
|
|
|
|
R |
L |
R |
CABLE IN |
ANT OUT S-VIDEO VIDEO |
L |
R |
|
|
|
|
|
|
|||
OMPONENT IN |
|
|
|
|
|
|
|
|
|
|
|
ANT IN |
OUTPUT |
|
|
|
|
|
|
SWITCH |
|
|
|
|
|
|
|
|
|
|
3Press the PLAY button on the VCR and match the appropriate programme between the TV and VCR for viewing.
1Connect the AUDIO / VIDEO jacks between TV and VCR. Match the jack colours (Video = yellow, Audio Left = white, and Audio Right = red)
2Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
3SelectAV input source using the INPUT button on the remote control.
|
AUDIO IN |
|
AV IN |
|
HDMI IN |
VIDEO |
(MONO) L AUDIO |
|
|
(RGB/DVI) |
R |
|||
|
|
|
|
|
|
VIDEO |
AUDIO |
ANTENNA/ |
|
Y |
PB |
PR |
L |
CABLE IN |
|
||||
RGB IN (PC) |
|
COMPONENT IN |
|
S-VIDEO VIDEO |
L |
R ANT IN |
OUTPUT |
|
ANT OUT |
SWITCH |
|
|
<![endif]>SETUP EQUIPMENT EXTERNAL
19
EXTERNAL EQUIPMENT SETUP
<![endif]>SETUP EQUIPMENT EXTERNAL
1Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colours.
(Video = yellow, Audio Left = white, and Audio Right = red)
2SelectAVinputsourceusingtheINPUTbutton on the remote control.
If connected to AV IN, select AV input source.
3Operatement. the corresponding external equipRefertoexternalequipmentoperatingguide.
|
AUDIO IN |
|
AV IN |
|
|
HDMI IN |
VIDEO |
(MONO) L |
AUDIO |
|
|
(RGB/DVI) |
R |
||||
|
|
|
|
|
|
|
VIDEO |
AUDIO |
ANTENNA/ |
||
Y |
PB |
PR |
L |
R |
CABLE IN |
|
|||||
RGB IN (PC) |
|
COMPONENT |
|
|
VIDEO L R
20
When using the remote control, aim it at the remote control sensor on the TV.
1Connect the signal cable from the monitor output socket of the PERSONAL COMPUTER to the PC input socket of the set.
2Connect the audio cable from the PC to theAUDIO IN (RGB) sockets of the set.
3Press the INPUT button to select RGB PC.
4SwitchonthePC,andthePCscreenappearsontheset. The set can be operated as a PC monitor.
|
|
AUDIO IN |
|
AV IN |
|
|
|
VIDEO (MONO) L AUDIO R |
|
||
HDMI IN |
|
(RGB) |
|
||
|
|
|
|
||
|
|
VIDEO |
|
AUDIO |
ANTE |
|
Y |
PR |
L |
R |
CABL |
RGB IN (PC) |
|
||||
|
COMPONENT IN |
|
|
||
|
|
|
|
RGB OUTPUT |
AUDIO |
<![endif]>SETUP EQUIPMENT EXTERNAL
! NOTE
►►User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product.
21
EXTERNAL EQUIPMENT SETUP
Tie cables together with a cable management as shown in the illustration.
<M197WAP/ M227WAP >
<![if ! IE]><![endif]>SETUP EQUIPMENT EXTERNAL
<M237WAP>
22