LG LW9228 User Manual [ru]

OWNER’S MANUAL

Network Dome Camera

Please read this manual carefully before operating your set and retain it for future reference.

MODELS LW9228 Series LW9228I Series LW9226 Series LW9226I Series

P/NO : MFL67122201 1104 (V1.5)

Safety Information

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

This lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modications to this equipment may cause harmful interference unless the modications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modication is made.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Safety Information

Warning: Do not install this equipment in a conned space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of re or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qu alied service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualied personnel only.

Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects lled with liquids, such as vases, should be placed on the apparatus.

To disconnect power from mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

LG Electronics hereby declares that this/ these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/ EC, 2006/95/EC, and 2009/125/EC.

European representative :

LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere. The Netherlands (Tel : +31-(0)36-547-8888)

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city oce, waste disposal service or the shop where you purchased the product.

EEE Compliance with Directive. (for Turkey only)

Safety Information

IMPORTANT SAFETY INSTRUCTIONS

Safety Information

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Safety Precautions

• Do not attempt to disassemble the camera To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualied service personnel for servicing.

• Avoid the camera with direct sunlight Do not aim the camera at bright objects.Whether the camera is in use or not, never face it with direct sunlight or other extremely bright objects. Otherwise blooming or smear may be caused.

• Handle the camera with care Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling or storage.

• Do not use strong solvents or detergents Use a dry cloth to the camera when it is dirty. If it is hard to remove the dirt on the camera, use a mild detergent and wipe it gently.

• Do not install this camera upside down This camera is designed for mounting on the ceiling or wall. If you install this camera upside down, for example, mounted on the oor, it may cause malfunction.

• Do not use the camera in such places as shown below. The lens may become cloudy due to condensation if the camera is used under the following conditions.

› Rapid temperature uctuation by switching an air

conditioner on and o.

› Rapid temperature uctuation due to frequent

door opening and closing.

› Use in an environment where eyeglasses become

foggy.

› Use in a room lled with cigarette smoke or dust.

If the lens becomes cloudy due to condensation, remove the dome cover and wipe all moist surfaces with a soft cloth.

Safety Information

• Before operating, please check proper temperature, humidity and power source ratings. Use the camera under conditions where temperature is from -10 °C to 50 °C and humidity is below 80 %. The input power source is AC 24 V.

• Consumables Parts having contacts such as the lens-drive motors, cooling fan built inside the camera are subject to wear with time. About replacement and maintenance of such parts, please ask the nearest service center.

Camera Installation Location

Discuss the installation location for the camera with your retailer, and select a place that is strong enough for the installation.

• Install the camera on a ceiling (concrete, etc.) at a location that is suciently strong to support it.

• Install the camera body on the foundation section of the building or sections having sucient bearing strength.

Never install or use the camera in the following locations

• Do not install it in areas exposed to direct sunlight or rain.

• Do not install the camera near the air outlet of an air conditioner.

• Near a swimming pool or other areas where chemicals are used.

• Food preparation areas and other locations where there are large amounts of steam vapor and oil, in ammable atmospheres, other special environments.

• Areas where radiation, X-rays, strong electric waves, or magnetism is generated.

• At sea, in coastal areas, or in areas where corrosive gas is being generated.

• Areas outside of the allowable ambient operating temperature range.

About Static Electricity Removal

Before installing the camera, touch a metal case or other metallic parts with your hand to remove static electricity from your body. Do not install in areas subjected to high amounts of humidity or dust. Doing so may cause internal components to damage more easily or malfunction. Do not wire cables near power lines.

Tightening the Screws

Screws should be tightened suciently in accordance with the materials and structure of the installation location. After tightening the screws, visually inspect them to make sure there is no unevenness and that each screw is tight.

Safety Information

Contents

14 ALARM output connections

15 Connecting Network

Safety Information

4 IMPORTANT SAFETY INSTRUCTIONS

4 Safety Precautions

Preparation

8 Introduction

8 Features

9 Accessories

10 Part Names and Functions

16 Connecting power source

16 Connecting Microphone and Speaker

Device

17 Mounting the camera

17 Removing the Protection Tape

17 Surface mount (optional)

19 Ceiling mount (optional)

21 Wall mount (optional)

23 Pendant mount (optional)

Operation and settings

27 Before using the system

27 Recommended PC Requirements

28 Accessing the LG IP device

29 LG Smart Web Viewer Overview

Installation

12 Connections

12 Precautions

12 Basic Connection Overview

13 Connecting Display device

13 ALARM input connection

30 Conﬁguring the LG IP camera

30 Accessing the Conﬁguration menu

30 System settings

32 Audio & Video settings

36 Network settings

38 User settings

39 Event settings

42 Auto Tracking

43 OSD Menu Setup

Contents

46 General operation

46 Camera menu settings

46 Focus setting

47 Exposure settings

48 White Balance setting

48 Day/Night setting

49 3D-DNR setting

49 Color setting

49 Sharpness setting

50 PAN/TILT Settings

50 Privacy Mask setting

50 Special setting

52 OSD Settings

52 User title setting

52 ZOOM MAG setting

52 FUNCTION setting

52 DOME ID setting

Appendix

58 Speciﬁcations

53 LANGUAGE Setting

53 RESET Setting

53 Information

53 Initialization

53 Factory reset

Reference

54 Troubleshooting

56 Open source software notice

Preparation

2 Preparation

Introduction

Preparation

The LG Network Camera is designed to use on an Ethernet network and must be assigned an IP address to make it accessible. This manual contains instructions on how to install and manage the LG Network Camera in your networking environment. Some knowledge of networking environments would be benecial to the reader. Should you require any technical assistance, please contact authorized service center.

Features

• High Sensitivity Support

The camera provides the high quality picture with

4.5 mm EX-view HAD CCD.

• Preset Position

Preset position is the function to register camera monitoring positions (preset positions). Maximum 128 Preset Positions are available. By entering the position numbers, you can move cameras to the preset positions. The moving speed and holding time are adjustable.

• Preset Tour

Preset Tour is the function to go through all the registered camera monitoring positions (preset positions). During the working PRESET TOUR, The FOCUS could not be operated properly under -10 °C (for LW9226(I) series only)

• Group Tour

Maximum 9 group tours are able to compose the group of preset, pattern, auto pan that the operator can program to be linked together in a sequence.

• Pattern recording function

A routine of manual operations can be stored and reproduced repeatedly. The Pan, Tilt and Zoom controls are available for pattern recording.

NOTE

The available total time of pattern diers depending on camera’s operation. When the pattern recording is full, the pattern recording will automatically stop.

• Privacy Mask

Privacy zone feature enables users to veil unwanted zones. This setting is used for masking unwanted zones, hiding them from display on the monitor screen. Up to 8 zones can be registered.

• Auto Pan

The camera has an Auto Pan function that enables to keep surveillance on every detail occurring around the specic area, which is preset to watch in advance. The camera can pan among the maximum 8 points you will set. The moving speed and holding time are adjustable.

• Auto Flip

When the camera is operated to tilt through the 90°, it can be watched the opposite side of the locations by Auto Flip of a 180° horizontally.

• Optical Zoom

- LW9228(I) series: The optical zoom range is 1x to 37x.

- LW9226(I) series: The optical zoom range is 1x to 27x.

• Digital Zoom

Digital zoom enhances the systems zoom range to 12 times beyond the optical zoom limit. Total system zoom range is below.

- LW9228(I) series: 37x (1x digital zoom) to 444x (12x digital zoom)

Preparation

- LW9226(I) series: 27x (1x digital zoom) to 324x (12x digital zoom)

• Alarm In function (4 channels)

Alarm input signals are supplied from external devices through the ALARM IN connector.

• Alarm Out function (2 channels)

When an event occurs, the camera sends output signals via the alarm output connector on the camera.

• Day & Night Function

This camera can be selected Color or Black & White. You can set Color in the daytime and Black & White at night due to the low illumination. (Filter Conversion type)

• DSS (Digital Slow Shutter) function

It is possible to highly sensitive surveillance because of DSS(Digital Slow Shutter) function.

• WDR (Wide Dynamic Range) function

The camera can be best condition to watch easily inside or outside in the strong back light.

• Power Supply

This camera must always be operated a AC 24 V. Certied/Listed, class 2 power supply only.

• Auto Tracking

This feature enables the camera to detect a moving object and track its movement automatically. Based on the conguration, it is possible to zoom in the object to identify it clearly.

Accessories

For LW9226I/LW9228I series

RJ-45 Adapter cable

For LW9226/LW9228 series

Camera main cable

RJ-45 adapter cable

Preparation

Wrench

PIPE Installation Bracket

Preparation

Part Names and Functions

LW9228I/LW9226I series for Indoor

Preparation

c d

e f

BNC connector cover cap

b Video output BNC connector

Supplies analog video signal (composite) to the connected device.

c Data Port A (RJ-45)

Input data port for alarm (relay) signal. RS-485 data communication is not available.

d Data Port B (RJ-45)

Output data port for alarm (relay) signal.

AUDIO IN (Line Level Input)

Input for a mono microphone, or a line-in mono signal.

f AUDIO OUT (Line Level Output)

Connect to an active speaker with a built-in amplier.

Power input jack

Connects to a AC 24 V power supply using proper cables.

h ETHERNET Port

Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached RJ-45 connector.

Locking screw

Tighten this screw to xing the Ceiling Mount Assembly with camera body.

j Dome Cover open button. k Dome Cover

Preparation

LW9228/LW9226 series for Outdoor

b c d

e f

BNC connector cover cap

b Video output BNC connector

Supplies analog video signal (composite) to the connected device.

c Data Port A (RJ-45)

Input data port for alarm (relay) signal. RS-485 data communication is not available.

d Data Port B (RJ-45)

Output data port for alarm (relay) signal.

AUDIO IN (Line Level Input)

Input for a mono microphone, or a line-in mono signal.

f AUDIO OUT (Line Level Output)

Connect to an active speaker with a built-in amplier.

Power input jack

Connects to a AC 24 V power supply using proper cables.

h ETHERNET Port

Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached RJ-45 connector.

Dome Cover

Preparation

Installation

3 Installation

Connections

Precautions

• The following steps of installation and connection work should be done by qualied service personnel or system

Installation

installers and should conform to all local codes.

• Before you install and connect the camera, check and prepare the required peripheral devices and cables.

• Before you connect the camera, turn o all devices to be connected, such as this camera and DVR.

• Do not touch the dome cover’s window.

Basic Connection Overview

LW9226I/9228I series (for Indoor) LW9226/9228 series (for outdoor)

Connecting Display device

The video signal connection between the camera and the monitor.

Display device connection

Installation

CAUTION

Do not connect one alarm sensor to the several camera’s alarm input connector.

Alarm input connection

ALARM input connection

You can connect up to 4 alarm sensors to the camera. Each alarm sensor should be connected with Alarm IN COM. You can adjust the signal state to NO (normally open) or NC (normally closed) through the setup menu.

1. Connect the RJ-45 Adapter cable to the PORT A (RJ-45) cable of the camera.

2. Connect the alarm device to the RJ-45 Adapter cable. When connecting lines, check and connect the color lines of the each device correctly. Refer to the below tables for color line information.

A B

C D

Alarm device

PORT ARJ-45 Adapter cable

RJ-45 Adapter cable

Port A

RJ-45 Adapter cable

No Description Color

RS-485 + White

RS-485 - Orange

NC Black

ALARM IN COM Red

ALARM IN 1 Green

ALARM IN 2 Yellow

ALARM IN 3 Blue

Installation

Alarm device

ALARM IN 4 Brown

Installation

PORT A of the LW9228I/9226I series

Description Color

RS-485 + Red/White

RS-485 - Black/White

ALARM IN COM Red

ALARM IN 1 White

ALARM IN 2 Light Green

ALARM IN 3 Yellow

ALARM IN 4

PORT A of the LW9228/9226 series

Description Color

RS-485 +

RS-485 - Blue

ALARM IN COM Yellow

ALARM IN 1

Pink

Green

Pink

ALARM output connections

Connect the alarm device to the alarm output data port. Alarm signal output at an event occurrence. You can set the Alarm Output to the normal open or normal close mode.

1. Connect the RJ-45 Adapter cable to the PORT B (RJ-45) cable of the camera.

2. Connect the alarm device to the RJ-45 Adapter cable. When connecting lines, check and connect the color lines of the each device correctly. Refer to the below tables for color line information.

Alarm Out connection

A B

C D

E F

G H

Alarm device

ALARM IN 2 Gray

ALARM IN 3 White

ALARM IN 4 Violet

NOTE

RS-485 data communication is not available.

RJ-45 Adapter cable

PORT BRJ-45 Adapter cable

Port B

RJ-45 Adapter cable

No Description Color

ALARM OUT [NO1] White

ALARM OUT [COM1] Orange

ALARM OUT [NC1] Black

NC Red

ALARM OUT [NO2] Green

ALARM OUT [COM2]

Yellow

Installation

PORT B of the LW9228I/9226I series

ALARM OUT [COM1]

ALARM OUT [NO1] Brown

ALARM OUT [COM2] Orange

ALARM OUT [NO2] Black

PORT B of the LW9228/9226 series

ALARM OUT [NC2] Blue

NC Brown

Description Color

ALARM OUT [NC1] Blue

ALARM OUT [NC2] Gray

Description Color

Connecting Network

You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration or monitor the image via network. After the installation, check the network settings for the remote control and monitoring work.

Connect the IP camera to your network using a standard RJ-45 network cable as shown below.

Violet

Installation

ALARM OUT [NO1] White Blue

ALARM OUT [COM1] Beige

ALARM OUT [NC1] Black

ALARM OUT [NO2] Brown

ALARM OUT [COM2] Red

ALARM OUT [NC2]

Orange

CAUTION

Output specications are lowactive, open-collector and a drive capacity of 30 V DC 0.5 A maximum. Connecting the alarm out incorrectly may cause damaging the camera.

Installation

Connecting power source

Connect a AC 24 V power source to the power input terminal as shown below.

Installation

Connecting Microphone and Speaker Device

Optionally connect an active speaker and/or external microphone with a built-in amplifier.

NOTE

Keep the microphone away from the speaker to avoid howling.

Installation

Mounting the camera

You can mount the camera on the ceiling or wall.

Removing the Protection Tape

You should remove the protection tape before installing the camera. Remove the protection tape carefully.

For LW9226/9228 series models.

1. Loosen the screws using the wrench and remove the dome cover.

2. Remove the protection tape and attach the dome cover.

For LW9226I/9228I series models.

1. Press the Dome Cover open button and then disassemble the dome cover by using ALIGN mark.

2. Remove the protection tape and attach the dome cover.

CAUTION

Surface mount (optional)

Follow the instructions below to surface mount the camera.

CAUTION

The building structure must be able to support 8 kg.

1. Use the installation guide template to check the mounting location. Face the front of the label toward the area of interest.

Installation

You must align the OPEN and LOCK mark correctly when you turn the dome cover to open or close. If you do not align the mark, it causes a malfunction.

Installation

2. Install the surface mounting bracket on the ceiling.

Installation

3. Assemble the camera and the surface mounting bracket by following step a and b. Align the locking point of the surface mounting bracket and the camera.

4. Tighten the locking screw.

5. Connect the cables to the cable jacks of the camera body. After installing the camera, you should arrange the cables using the outlet box to protect the cables.

+ 42 hidden pages