LG LW91105SS Owner’s Manual
http://au.lge.com (Australia)
http://nz.lge.com (New Zealand)
Built In Oven
Installation and Operating Instructions
LW91105SS
To avoid the risk of accidents or damage to the OVEN, it is essential to read these operating instructions before it is installed or used for the first time.
And please keep this manual for later reference.
P/No.: MFL62060309
Contents |
|
|
Instructions for safe and proper user |
....................................... 3 |
|
1. |
Instructions for safe and proper use ....................................... |
3 |
Instructions for the installer ...................................................... |
5 |
|
2. |
Installation .............................................................................. |
5 |
3. |
Description of controls ............................................................ |
7 |
4. |
Use of the oven .................................................................... |
12 |
5. |
Available accessories ........................................................... |
13 |
6. |
Cooking hints ....................................................................... |
14 |
Instructions for the user .......................................................... |
20 |
|
7. |
Cleaning and maintenance .................................................. |
20 |
8. |
Extraordinary maintenance .................................................. |
22 |
INSTRUCTIONS FOR THE INSTALLER: these are intended for the authorised person who must, install the appliance, set it functioning and carry out an inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the correct procedures for cleaning and maintenance of the appliance.
2
Instructions for safe and proper user
1. Instructions for safe and proper use
This manual is an integral part of the appliance and therefore must be kept in its entirety and in an accessible place for the whole working life of the oven. We advise careful reading of this manual and all the instructions therein before using the oven. Installation must be carried out by qualified personnel in accordance with the regulations in force. This appliance is intended for domestic uses and conforms to current regulations in force. The appliance has been built to carry out the following functions: Cooking and heating-up of food. All other uses are considered improper.
The manufacturer declines all responsibility for improper use.
Do not leave the packing in the home environment. Separate the various waste materials and take them to the nearest special garbage collection centre.
It is obligatory for the electrical system to be grounded according to the methods required by safety rules.
When linking up to mains by plug and socket, make sure that both are compatible and connect by means of a power cable complying with applicable regulations and power requirements.
The socket must be accessible after the appliance has been built in.
Never unplug by pulling on the cable.
Do not obstruct ventilation openings and heat dispersal slits.
Immediately after installation carry out a brief inspection test of the oven, following the instructions below. Should the appliance not function, disconnect it from the supply and call the nearest technical assistance centre.
Never attempt to repair the appliance.
3
Instructions for safe and proper user
Always check that the control knobs are in the “ZERO” (OFF) position when you finish using the oven.
Never put inflammable objects in the oven: They could be accidentally lighted and cause fires.
During use the appliance becomes very hot. Take care not to touch the heating elements inside the oven.
The I.D. plate with technical data, registration number and brand name is positioned visibly on the oven door frame.
The plate must not be removed.
The use of this appliance is not permitted to people (including children) of reduced physical and mental ability, or lacking in experience in the use of electrical appliances, unless they are supervised or instructed by adults or people responsible for their safety.
This appliance is designed for cooking food in a domestic application and it shall not be used as a space heater.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
Before the appliance is put into operation, all the labels and protective films applied inside or outside must be removed with the exception of the rating I.D. label.
The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the appliance or by the use of non-original spares.
4
Instructions for the installer
2. Installation
2.1 Electrical connection
Check that mains voltage and power cable ratings are as per the indications provided on the label attached to the oven door frame.
This label must never be removed.
It is obligatory for the electrical system to be grounded according to the methods required by safety rules.
If a plug and socket connection is being used make sure that the plug and socket are compatible. Avoid use of adapters and shunts as these could cause overheating and risk of burns. Extension leads must not be used.
If a fixed connection is being used fit power line with an omnipolar circuit breaker or isolation switch with a contact opening gap equal to or greater than 3 mm in an easily accessible position in proximity to the oven.
For operation on 230-240V~: use an H05RR-F / H05V2V2-F type three-core cable (3 x 1.5 mm2).
The cable end to be connected to the appliance must be provided with an
ground wire (yellow-green) at least 20 mm longer.
The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the appliance.
5
Instructions for the installer
2.2 Mounting the oven
The oven is designed for mounting into any piece of furniture as long as heat-resistant. Proceed according to the dimensions shown in Figures 1, 2.
Fixing is carried out using 4 screws at the corners “C” of the oven door frame, after removing the side panels secured by the screws “A” and the supports “B” as shown in figure 3. To replace the side panels, take care to engage the pins inside them correctly with the supports “B”, then retighten the screws “A”.
You are advised to use the side handles provided in order to facilitate installation of the appliance.
6
Before completely building in the oven, remove the side handles which might cause unpleasant vibrations and noise during normal operation of the oven.
Never use the oven door to lever the oven into place when fitting.
Avoid exerting too much pressure on the oven door when open.
The oven door should not be used as a resting table for food being removed or put in to the oven.
3. Description of controls
3.1 Front control panel
All the oven controls are grouped together on the front panel.
FUNCTION SWITCH KNOB
Rotate the knob in either direction to select desired function from the following:
7
Instructions for the installer
|
|
|
NO FUNCTION SET |
|
|
|
|
UPPER AND LOWER |
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
HEATING ELEMENT + |
|
|
|
OVEN LIGHT |
|
|
|
|
VENTILATION |
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
UPPER AND LOWER |
|
|
|
|
|
DEFROSTING |
|
|
|
|
|
|
|
|
||
|
|
|
HEATING ELEMENT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
WIDE GRILL ELEMENT |
|
|
|
|
|
|
|
|
|
+ SPIT ROASTING |
|
|
|
|
|
|
|
|
|
FUNCTION |
|
|
|
|
|
|
|
|
|
WIDE GRILL ELEMENT + |
|
|
|
|
|
|
|
|
|
VENTILATION + SPIT |
|
|
|
|
|
|
|
|
|
ROASTING FUNCTION |
|
|
|
|
|
|
THERMOSTAT KNOB
Cooking temperature is selected by turning the knob clockwise to the desired setting, between 50° and 250°C.
THERMOSTAT INDICATOR LIGHT
When this light comes on, the oven is heating up. When this light goes out, the preset heating temperature has been reached.
When the light turns on and off, the temperature inside the oven is steady at the set temperature.
8
Loading...