LG LUTE4619SN User Manual

OWNER’S MANUAL

ELECTRIC RANGE

Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times.

LUTE4619SN

MFL68881513

www.LGSIGNATURE.com

TABLE OF CONTENTS

IMPORTANT SAFETY

INSTRUCTIONS

PRODUCT OVERVIEW

9 Parts 9 Accessories

INSTALLATION

10 Installation Overview 10 Product Specifications 11 Before Installing the Range 12 Installing the Range 14 Connecting Electricity 18 Engaging the Anti-tip Device 18 Optional Rear Filler 18 Test Run

OPERATION

19 Control Panel Overview 20 Knob Positions 21 Changing Oven Settings

21 Clock 21 Oven Light 21 Minimum & Maximum Default Settings 22 Timer On/Off 22 Wi-Fi 22 Settings

-Setting the Hour Mode

-Setting Convection Auto Conversion

-Adjusting the Oven Temperature

-Turning the Preheat Alarm Light On/Off

-Adjusting the Beeper Volume

-Selecting Fahrenheit or Celsius

-Adjusting Cooktop On Alert Volume 23 Lock Out 24 Start Time (Delayed Timed Cook) 24 Cook Time (Timed Cook)

25 Using the Cooktop

25 Cooking Areas 25 Hot Surface Indicator 25 Using the Cooktop Elements 26 The Recommended Surface Cooking

Setting 27 Using the Proper Cookware 27 Choosing Cookware 27 Home Canning Tips

28 Using the Oven

28 Before Using the Oven 28 Oven Vent 28 Using Oven Racks 28 Bake 29 Convection Mode 30 Recommended Baking and Roasting Guide 31 Broil 32 Recommended Broiling Guide 33 Warm 33 Proof 33 Meat Probe 34 Remote Start

SMART FUNCTIONS

35 Application Installation 35 Product Registration 35 Using the Wi-Fi Function 36 FCC Notice 36 FCC RF Radiation Exposure Statement

MAINTENANCE

37 Cleaning the Glass-Ceramic Cooktop 38 EasyClean 41 Self Clean 43 Changing the Oven Light 43 Cleaning the Exterior 45 Removing and Replacing the Lift-Off Oven

Doors

47 Door Care Instructions

TROUBLESHOOTING

48 FAQs 50 Before Calling for Service

SMART DIAGNOSIS™

54 Using Smart Diagnosis™

WARRANTY

Rev.00_022017

IMPORTANT SAFETY INSTRUCTIONS

Read and follow all instructions when using the range to prevent the risk of fire, electric shock, personal injury, or damage. This guide does not cover all possible conditions that may occur. Always contact your service agent or manufacturer about problems that you do not understand.

Download this owner's manual at: http://www.LGSIGNATURE.com

This is the safety alert symbol. This symbol alerts you to potential hazards that can result in property damage and/or serious bodily harm or death. All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION. These words mean:

WARNING CAUTION

ANTI-TIP DEVICE

WARNING

TO REDUCE THE RISK OF TIPPING, THE APPLIANCE MUST BE SECURED BY A PROPERLY INSTALLED ANTI-TIP DEVICE. TO CHECK IF THE DEVICE IS INSTALLED PROPERLY, VERIFY THAT THE ANTI-TIP DEVICE IS ENGAGED, OR GRASP THE TOP REAR EDGE OF THE RANGE BACK GUARD AND CAREFULLY ATTEMPT TO TILT IT FORWARD. Refer to the installation section for instructions.

- Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result

in minor or moderate injury.

ENGLISH

%It is possible for a child or adult to tip the range and be killed. %Verify that the anti-tip device has been properly installed and

attached to the floor or wall and engaged to the leveling leg of the range.

%Do not operate the range without the anti-tip device in place and

engaged.

%Never remove the oven legs. The range will not be secured to the

anti-tip bracket if the legs are removed.

%Do not step or sit on the oven door. The range could be tipped and

injury might result from spilled hot liquid, food, or the range itself.

%Do not rest large, heavy items such as whole turkeys on the open

oven door. The range could tip forward and cause injury.

%Reengage the anti-tip device after pulling the range out for

cleaning, service, or any other reason.

%Failure to follow these instructions can result in death or serious burns to children or

adults.

Anti-tip bracket

Leveling leg

IMPORTANT SAFETY INSTRUCTIONS

SAFETY PRECAUTIONS

WARNING

This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

%DO NOT TOUCH HEATING ELEMENTS OR INTERIOR SURFACES OF OVEN. Heating

elements may be hot even though they are dark in color. Interior surfaces of an oven become hot enough to cause burns. During and after use, do not touch or let clothing or other flammable materials contact heating elements or interior surfaces of oven until they have had sufficient time to cool. Other surfaces, such as oven vent openings and surfaces near these openings, oven doors, and windows of oven doors, also get hot and may cause burns if not cooled.

%Use care when opening door. The hot air and steam that escape can cause burns to

hands, face and eyes. Let hot air or steam escape from the oven before removing or replacing food in the oven.

%Do not repair or replace any part of the appliance unless specifically recommended in the

manual. All other servicing should be performed by a qualified technician.

%Do not use harsh etching, abrasive cleaners or sharp metal scrapers to clean the oven

door glass since they can scratch the surface. Scratches may cause the glass to shatter.

WARNING

If the door glass, surface, or oven heating unit of the range are damaged, discontinue use of the range and call for service.

%Do not operate the oven without the charcoal heater mesh. %Do not use plastic to cover food. Use foil or oven-safe lids only. %Do not allow anyone to climb, stand or hang on the door or cooktop. They could damage

the range and even tip it over, causing severe personal injury.

%Do not line the oven walls, racks, bottom, or any other part of the oven with aluminum foil

or any other material. Doing so will disrupt heat distribution, produce poor baking results and cause permanent damage to the oven interior (aluminum foil will melt to the interior

surface of the oven) %Never attempt to dry a pet in the oven. %Never use your appliance for warming or heating the room. %Always use pot holders or oven mitts when removing food from the oven or the surface

element. Cookware will be hot. Use only dry pot holders. Moist or damp pot holders on

hot surfaces may result in burns from steam. Do not let the pot holder touch hot heating

elements. Do not use a towel or other bulky cloth to remove food. %Do not heat unopened food containers. Pressure in the containers may cause them to

burst which may result in injury. %To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage

space located above the surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood that projects horizontally a

minimum of 5 inches beyond the bottom of the cabinets.

IMPORTANT SAFETY INSTRUCTIONS

FLAMMABLE MATERIALS

WARNING

Be certain that all packing materials are removed from the appliance before operating. Keep plastic, clothes, paper, and other flammable materials away from parts of the appliance that may become hot.

%Do not store or use flammable material in the oven or near or on the cooktop. Flammable

materials include paper, plastic, pot holders, linens, wall coverings, curtains, and gasoline

or other flammable vapors and liquids such as grease or cooking oil. These materials can

be ignited when the oven and cooktop are in use. %Wear proper apparel. Do not wear loose-fitting or hanging garments, which may ignite if

they contact hot surfaces, and cause severe burns. %Do not use the oven for drying clothes. Only use the oven for its intended purpose. %If a cabinet storage is provided directly above cooking surface, place items that are not

frequently used and can be safely stored in an area subjected to heat. Temperatures may

be unsafe for volatile items such as flammable liquids, cleaners or aerosol sprays.

ELECTRICAL SAFETY

CAUTION

ENGLISH

%Always disconnect power from the appliance before servicing. %Do not use aluminum foil or any other material to line the oven bottom.

Improper installation of these liners may result in a risk of electric shock or fire. %Do not allow aluminum foil or the temperature probe to contact heating elements.

WARNING

Before replacing the oven light bulb, switch off the electrical power to the oven at the main fuse or circuit breaker panel. Failure to do so can result in severe personal injury, death, or electrical shock.

DEEP FAT FRYER

%Use extreme caution when moving or disposing of hot grease. %Always heat fat slowly, and watch as it heats. %If frying combinations of oils and fats, stir them together before heating. %Use a deep fat thermometer, if possible, to prevent overheating fat beyond the smoking

point. %Use the least possible amount of fat for effective shallow or deep-fat frying. Filling the pan

with too much fat can cause spillovers when food is added.

IMPORTANT SAFETY INSTRUCTIONS

CHILD SAFETY

%Do not touch the hot surface between the bottom of the oven door and the top of the

drawer on the front of the oven while the oven is in operation. The surface becomes hot

and can cause burns and other injury. %Do not leave small children unattended near the oven.

WARNING

Do not leave children alone or unsupervised near the appliance when it is in use or is

still hot. Children should never be allowed to sit or stand on any part of the appliance as they could be injured or burned.

CAUTION

Do not store items of interest to children in cabinets above a range or on the back guard of a range – children climbing on the range to reach items could be seriously injured.

%Never let a child hang on the oven door. %Do not allow children to crawl into the oven. %Let hot utensils cool in a safe place, out of reach of small children. %Children should not be allowed to play with controls or other parts of the appliance.

GLASS-CERAMIC COOKING SURFACE

%Surface units may be hot even though they are dark in color. Areas near surface units may

become hot enough to cause burns. During and after use, DO NOT TOUCH SURFACE

UNITS OR AREAS NEAR UNITS or let clothing or other flammable materials contact

surface units or areas near units until they have had sufficient time to cool. This includes

the cooktop and the area above the oven door. %Do not cook on a broken cooktop. If the cooktop is broken, cleaning solutions and

spillovers may penetrate the broken cooktop and create a risk of electric shock. Contact a

qualified technician immediately. %Do not use the glass cooktop surface as a cutting board. %Do not place or store items that can melt or catch fire on the glass cooktop, even when it

is not being used. %Choose proper burner size. For smaller pots and pans, use the smaller heating

elements. For larger pots and pans, use the larger heating elements. Select pans that

have flat bottoms large enough to cover the heating elements. Using undersized pans

exposes a portion of the heating element to direct contact and may result in clothing

burning. %Glazed cookware. Only certain types of glass, glass-ceramic, ceramic, earthenware,

or other glazed cookware are suitable for range-top service without breaking due to the

sudden change in temperature. %Never cook directly on the glass. Always use cookware. %Always turn the surface units off before removing cookware. %Turn cookware handles inward so they don't extend over adjacent surface units.

This reduces the risk of burns, ignition of flammable materials, and spillage due to

unintentional contact with the cookware. %Immediately clean spills on the cooking area to prevent a tough cleaning chore later. %Some cleaners can produce dangerous fumes if applied to a hot surface.

IMPORTANT SAFETY INSTRUCTIONS

%Always place the pan in the center of the surface unit you are cooking on. Never leave

surface units unattended at high heat settings. Proper contact of cookware to burner

also will improve efficiency. Boilovers cause smoking and greasy spills that may catch on

fire. %Clean cooktop with caution. Do not use sponges or cloth to wipe spills on a hot cooking

area. Use a proper metal scraper. If a wet sponge or cloth is used to wipe spills on a hot

cooking area, it can cause steam burns. Some cleaners can produce noxious fumes if

applied to a hot surface. %Do not turn surface units on before placing cookware. %Do not store heavy items above the cooktop surface that could fall and damage it. %Do not place aluminum foil or plastic items such as salt and pepper shakers, spoon

holders, or plastic wrappings or any other material on the range when it is in use. %Do not use a steel-wool pad or scrub pad or abrasive cleaning pads. They can scratch the

surface.

ENERGY SAVING TIPS

%Multiple-rack cooking saves time and energy. Whenever possible, cook foods requiring the

same cooking temperature together in one oven. %For optimal performance and energy savings, follow the guides on page 30 for proper rack

and pan placements. %Match the size of the cookware to the amount of food being cooked to save energy when

heating. Heating ½ quart of water requires more energy in a 3-quart pot than in a 1-quart

pot. %Use cookware with flat bottoms to provide the best contact with the cooktop surface when

cooking on the glass-ceramic cooktop. %Match the size of the cooktop burner or element to the size of the cookware in use. Using

a large element for a small pan wastes heating energy, and the exposed surface of the

element is a burn or fire hazard. %Reduce energy use by cleaning light oven soils with the EasyClean

self-clean. %Avoid opening the oven door more than necessary during use. This helps the oven

maintain temperature, prevents unnecessary heat loss, and saves on energy use.

feature instead of

ENGLISH

SAFETY DURING USE

%Do not touch the oven racks while they are hot. %If a rack must be moved while the oven is hot, do not let the pot holder contact the hot

heating element in the oven. %Use caution with the Timed Cook or Delayed Timed Cook features. Use the automatic

timer when cooking cured or frozen meats and most fruits and vegetables. Foods that can

easily spoil, such as milk, eggs, fish, meat or poultry, should be chilled in the refrigerator

first. Even when chilled, they should not stand in the oven for more than 1 hour before

cooking begins, and should be removed promptly when cooking is complete. Eating

spoiled food can result in sickness from food poisoning. %Accessible parts may become hot when the grill is in use. %Do not place food or cookware on the bottom of the oven cavity. Doing so will cause

permanent damage to the oven bottom finish. %Do not use water on grease fires. Should an oven fire occur, leave the oven door closed

and turn the oven off. If the fire continues, throw baking soda on the fire or use a fire

extinguisher. Do not put water or flour on the fire. Flour may be explosive and water can

spread a grease fire and cause personal injury.

IMPORTANT SAFETY INSTRUCTIONS

%Pull the oven rack to the stop-lock position when loading and unloading food from the

oven. This helps prevent burns caused by touching hot surfaces of the door and oven

walls. %Do not use the oven if a heating element develops a glowing spot during use or shows

other signs of damage. A glowing spot indicates the heating element may fail and present

a potential burn, fire, or shock hazard. Turn the oven off immediately and have the heating

element replaced by a qualified service technician. %When using cooking or roasting bags in the oven, follow the manufacturer’s directions.

SAFETY WHEN CLEANING

%Open a window or turn on a ventilation fan or hood before self-cleaning. %If the oven is heavily soiled with oil, self-clean the oven before using the oven again. The

oil could cause a fire. %Wipe up heavy soil on the bottom of the oven before using the Self Clean function. %Do not use oven cleaners. Commercial oven cleaner or oven liner protective coating of

any kind should not be used in or around any part of the oven. %Never keep pet birds in the kitchen. The health of birds is extremely sensitive to the fumes

released during an oven self-clean cycle. Fumes may be harmful or fatal to birds. Move

birds to a well-ventilated room. %Clean in the self-clean cycle only parts listed in this manual. Before self-cleaning the oven,

remove the broiler pan, all oven racks, the meat probe and any utensils or food from the

oven. %Important Instruction. The oven displays an F error code and sounds three long beeps

during the self-cleaning process if it malfunctions in the self-clean mode. Switch off the

electrical power to the main fuse or breaker and have the oven serviced by a qualified

technician. %It is normal for the cooktop of the range to become hot during a self-clean cycle.

Therefore, touching the cooktop during a self-clean cycle should be avoided. %Never pour cold water over a hot oven for cleaning. Doing so may cause the oven to

malfunction. %Make sure oven lights are cool before cleaning. %Do not clean door gasket. The door gasket is essential for a good seal. Care should be

taken not to rub, damage, or move the gasket. %If there is a fire in the oven during self-clean, turn the oven off and wait for the fire to go

out. Do not force the door open. Introduction of fresh air at self-clean temperatures may

lead to a burst of flame from the oven. Failure to follow this instruction may result in severe

burns.

COOK MEAT AND POULTRY THOROUGHLY

%To protect against food-borne illnesses, cook meat and poultry thoroughly. The USDA has

indicated the following as safe minimum internal temperatures for consumption:

%Ground beef: 160 °F %Poultry: 165 °F %Beef, veal, pork, or lamb: 145 °F %Fish/seafood: 145 °F

PRODUCT OVERVIEW

Parts

Cooktop Control panel

Cooktop controller

Upper oven door

Lower oven door

Accessories

Included Accessories

ENGLISH

Model & serial number plate

Oven mode knob Gasket

Rack

Heavy rack (2ea)

Meat probe (1ea) 5HDU¿OOHUHD Owner’s manual

Gliding rack (1ea) Spray bottle

(1ea)

Non-scratch scouring

pad (1ea)

Cleaner

Cooktop cleaner

(1ea)

Cleaning

pad

Cooktop cleaning pad

(1ea)

Optional Accessories

Grid Broiler pan

NOTE

%Contact the LG SIGNATURE Customer Information Center at 1-800-984-6306 if any accessories are

missing. %For your safety and for extended product life, only use authorized components. %The manufacturer is not responsible for product malfunction or accidents caused by the use of separately

purchased, unauthorized components or parts. %The images in this guide may be different from the actual components and accessories, which are subject

to change by the manufacturer without prior notice for product improvement purposes.

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another location.

Check and choose the

proper location

240 V or 208 V

Black White Red

Terminal block

Conduit connection plate

Install anti-tip device Level the range Connect electric range

Plug in the power cord Engage the anti-tip device Test run

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Oven Range Models LUTE4619SN

Description Electric Slide In Oven Range Electrical requirements 15.5 kW 120/240 VAC or 11.6 kW 120/208 VAC

Exterior Dimensions

Height to cooking surface 36" (91.4 cm) Net weight 188.7 lb (85.6 kg)

Total capacity

29 7/8" (W) x 37 7/8" (H) x 28 15/16" (D) (D with door closed)

75.9 cm (W) x 96.2 cm (H) x 73.5 cm (D) (D with door closed)

Upper Oven: 3.0 cu. ft. Lower Oven: 4.3 cu. ft. Total cap.: 7.3 cu. ft.

INSTALLATION

Before Installing the Range

WARNING

Tip - Over Hazard

A child or adult can tip the range and be killed. Verify the anti-tip bracket has been installed. Ensure the anti-tip bracket is engaged when the range is moved. Do not operate the range without the anti-tip bracket in place. Failure to follow these instructions can result in death or serious burns to children and adults.

To check that leveling leg is inserted into anti-tip bracket, grasp the top rear edge of the range and carefully attempt to tilt it forward.

Tools Needed

Anti-tip bracket

Leveling leg

If you did not receive an anti-tip bracket with your purchase, call 1-800-984-6306 to receive one at no cost.

WARNING

%The information in this manual should be

followed exactly. Failure to do so may result in fire, electrical shock, property damage, personal injury, or death.

%Wear gloves during the installation

procedure. Failure to do so can result in bodily injury.

ENGLISH

Phillips screwdriver

Level

Flat-blade screwdriver

Adjustable wrench

Parts Provided

Template (1) Anti-tip bracket kit (1)

Anchor sleeves (6) Lag bolts (6)

5HDU¿OOHU

/4" Nut driver

Drill

Pliers

Safety glasses

Parts Not Provided

4-Wire cord or

3-Wire cord

(UL approved 40 or 50

AMP)

Tape measure

Strain relief

(For conduit

Installations only)

NOTE

%Observe all governing codes and ordinances. %Have the installer show you the location of the circuit breaker or fuse. Mark it for easy reference. %As when using any appliance generating heat, there are certain safety precautions you should follow. %Be sure your range is installed and grounded properly by a qualified installer or service technician.

Gloves

INSTALLATION

Installing the Range

Unpacking and Moving the Range

CAUTION

%You should use two or more people to move

and install the range. (Excessive Weight

Hazard) Failure to do so can result in back or

other injury. %Do not use the door handles to push or

pull the range during installation or when

moving the range out for cleaning or

service. Doing so can result in serious damage

to the door of the range.

Remove packing material, tape and any temporary labels from your range before using. Do not remove any warning-type labels, the model and serial number label, or the Tech Sheet that is located on the back of the range.

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your range.

Your range is heavy and can be installed on soft floor coverings such as cushioned vinyl or carpeting. Use care when moving the range on this type of flooring. Use a belt when moving the range to prevent damaging the floor. Or slide the range onto cardboard or plywood to avoid damaging the floor covering.

Choosing the Proper Location

CAUTION

%Avoid placing cabinets above the range. To

minimize the hazard caused by reaching over the open flames of operating burners, install a ventilation hood over the range that projects forward at least five inches beyond the front of the cabinets.

%Make sure wall covering, countertop and

cabinets around the range can withstand the heat (up to 194 °F) generated by the range. Discoloration, delamination or melting

may occur. This range has been designed to comply with the maximum allowable wood cabinet temperature of 194 °F.

%Before installing the range in an area

covered with linoleum or other synthetic floor covering, make sure the floor covering can withstand temperatures of at least 200 °F (93 °C).

%Use an insulated pad or

plywood under the range if installing the range over carpeting.

The range should always be plugged into its own individual properly grounded electrical outlet. This prevents overloading house wiring circuits which could cause a fire hazard from overheated wires. It is recommended that a separate circuit serving only this appliance be provided.

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280), or when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

%When this range is installed in a mobile home, it

must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

%A four-wire power supply cord or cable must be

used in a mobile home installation.

/4 in. (0.64 cm)

INSTALLATION

Dimensions and Clearances

NOTE

Save for the use of the local electrical inspector.

3" (7.6 cm)

Acceptable gas pipe and electrical outlet area

24"

(60.9 cm)

36"

(91.4 cm)

29.8"

(75.7 cm)

(60.9 cm)

Cabinet opening

Cabinet

(10 cm)

24"

ENGLISH

3" (7.6 cm)

25"

Normal counter

(63.5 cm)

top depth

36" (91.4 cm)

Counter top height

Wall

11" (28 cm)

(10 cm)

Center

2.5" (6.3 cm)

5" (13 cm)

(15.2 cm)

(23 cm)

2.5"

(6.3 cm)

15" (38 cm)

(15.2 cm)

(23 cm)

A = 30" (76.2 cm) For U.S.A = 30" (76.2 cm) ~ 31" (78.7 cm) For CANADA

For installation in Canada, a free-standing range is not to be installed closer than

/32" (12 mm) from any

adjacent surface.

Maximum depth for cabinets above countertops

/4"

(0.64 cm)

13"

(33.0 cm)

Front edge of the range side panel forward from cabinet

36"

(91.4 cm)

*30" (76.2 cm)

Minimum

5"(12.7 cm) Minimum

30"

(76.2 cm)

**15"

(38.1 cm)

Minimum Dimensions

* 30" (76.2 cm) minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet; or 24" (60.9 cm) minimum when bottom of wood or metal cabinet is protected by not less

/4" (0.64 cm) flame retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015"

than mm)

stainless steel, 0.024" (0.610 mm) aluminum or 0.020" (0.508 mm) copper.

(0.381

** 15" (38.1 cm) minimum between countertop and adjacent cabinet bottom.

INSTALLATION

Installing the Anti-tip Device

WARNING

Tip - Over Hazard

To check that leveling leg is inserted into anti-tip bracket, grasp the top rear edge of the range and carefully attempt to tilt it forward.

Screw must enter wood or concrete

Anti-tip bracket

Locate the anti-tip bracket using the template

An anti-tip bracket is packaged with the template. The instructions include necessary information to complete the installation. Read and follow the range installation instruction sheet (template).

Leveling the Range

Level the range by adjusting the leveling legs with a wrench. Extending the legs slightly may also make it easier to insert the rear leg into the anti-tip bracket.

Leveling leg

Wall plate

Use a level to check your adjustments. Place the level diagonally on the oven rack, and check each direction for level.

First check direction Then check direction

. If the level doesn’t show level

on the rack, adjust the leveling legs with a wrench.

Connecting Electricity

Electrical Requirements

This appliance must be installed and grounded on a branch circuit by a qualified technician in accordance with the National Electrical code ANSI/NFPA NO. 70 latest edition.

All wiring should conform to Local and NEC codes. This range requires a single-phase, 3 wire, A.C 120/208 V or 120/240 V 60 Hz electrical system. Use only a 3-conductor or a 4-conductor UL-listed range cord with closed-loop terminals, open-end spade lugs with upturned ends or similar termination. Do not install the power cord without a strain relief.

A range cord rated at 40 amps with 120/240 minimum volt range is required. If a 50 amp range cord is used, it should be marked for use with 1 diameter connection openings. This appliance may be connected by means of a conduit or power cord. If a conduit is being used, go to page 17 for

3 wire conduit connections or 4 wire conduit connections.

INSTALLATION

WARNING

%Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack

in the line so that the range can be moved if

servicing is ever necessary.

%The power supply cord and plug should

not be modified. If it will not fit the outlet,

have a proper outlet Installed by a qualified

electrician.

%Using an extension cord to connect the

power is prohibited. Connect the power

cord and plug directly.

%Electrical ground is required on this

appliance.

%Make sure that the power cord is not

pinched by the range or heavy objects.

Failure to do so can result in serious burns or

electrical shock.

Specified power-supply-cord kit rating

Diameter (inches)

Range rating, watts

Specified

rating of

power

120/240

volts

3-wire

8,750 16,500

16,501 22,500

120/208

volts

3-wire

7,801 12,500

12,501 18,500

supply-

cord kit,

amperes

40 or 50A

3, 4 - Wire electrical wall Receptacle

of Range

connection

Opening

Power

cord

Conduit

1 1/

Use the cord/conduit connection plate to install the

ENGLISH

power cord or conduit. Leave the connection plate as installed for power cord installations. Remove the connection plate for conduit installations and use the

smaller 1

/8 in. (3.5 cm) power cord hole.

/8 in. (2.8 cm) conduit hole instead of the

/8"

(2.8 cm) Conduit

13/8"

(3.5 cm) Cord

Remove the conduit connection plate

For power cord installations, hook the strain relief over the 1

/8 in. (3.5 cm) power cord hole located below the rear of the oven. Insert the power cord through the strain relief and tighten it.

Conduit connection plate

Power cord

Assembling power cord strain relief at the 1

/8" opening

For conduit installations, insert the conduit strain relief in the 11/8 in. (2.8 cm) conduit hole. Then install the conduit through the body of the strain relief and fasten the strain relief with its ring.

4 Wire receptacle (14-50R)

3 Wire receptacle (10-50R)

Connecting the Power Cord

The rear access cover must be removed. Loosen the two screws with a screwdriver. The terminal block will then be accessible.

Access cover

Ring

Body

Assembling conduit cord strain relief at the 1

Cord/ Conduit connection plate

Conduit

/8" opening

INSTALLATION

3-Wire Connection : Power Cord

WARNING

%The middle (neutral or ground) wire, which

is white, of a 3-wire power cord or a 3-wire conduit has to be connected to the middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block.

Failure to do so can result in electrical shock, severe personal injury or death.

Install the power cord as follows:

For power cord installations, hook the strain relief over the power cord hole (1 of the oven. Insert the power cord through the strain relief and tighten it.

Do not install the power cord without a strain relief.

Remove the lower 3 screws from the terminal

block and retain them. Insert the 3 screws through each power cord

terminal ring and into the lower terminals of the terminal block. Make sure that the center (neutral) wire, which is white, is connected to the center lower position of the terminal block.

Tighten the 3 screws securely into the terminal

block. Do not remove the ground strap connections.

3-wire connection

Black White Red

) located below the rear

4-Wire Connection : Power Cord

WARNING

%Only a 4-conductor power-supply cord

kit rated 120/240 volts, 50 amperes and marked for use with ranges with closedloop connectors or opened spade lugs with upturned ends shall be used. The white middle (neutral) wire of the power cord or 4-wire conduit has to be connected to the middle post of the main terminal block. The other two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block. The 4th ground wire (green) must be connected to the frame of the range with the ground screw. Failure

to do so can result in electrical shock, severe personal injury or death.

Install the power cord as follows: Do not install the power cord without a strain

relief.

Remove the lower 3 screws from the terminal

block and retain them. Remove the ground screw and bend the end of

the ground strap up so the slot is over the hole of the center screw removed in step 1.

Insert the ground screw into the power cord

ground wire (green) terminal ring and secure it to the range frame.

Insert the 3 screws through each power cord

terminal ring and into the lower terminals of the terminal block. Make sure that the white center (neutral) wire is connected to the center lower position of the terminal block.

Terminal block

Conduit connection plate

If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

Tighten the 3 screws securely into the terminal

block. The center screw now attaches the bent up ground strap to the block.

4-wire connection

Black White Red

Terminal block

Ground screw

If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

Conduit connection plate

Ground strap

Bend strap up and attach

INSTALLATION

3-Wire Connection: Conduit

Install the conduit as follows:

Remove the conduit connection plate from the rear of the oven and rotate it. The conduit hole (1 be used.

First, prepare the conduit wires as shown below.

3-Wire

Conduit connection plate

Second, install the conduit strain relief. For conduit installations, purchase a strain relief and

insert it in the 1 install the conduit through the body of the strain relief and fasten the strain relief with its ring. Reinstall the bracket. For conduit connections: If the wire in the conduit is copper it must be 8 or 10 AWG wiring. If the wire in the conduit is aluminum it must be 6 or 8 AWG wiring.

Loosen the lower 3 screws from the terminal

block. Insert the bare wire (white/neutral) end through

the center terminal block opening. Do not remove the ground strap connections.

/8 in. (2.8 cm) conduit hole. Then

4-Wire

/8") must

Ground wire

4-Wire Connection: Conduit

WARNING

%The white middle (neutral) wire of the power

cord or 4-wire conduit has to be connected to the middle post of the main terminal block. The other two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block. The 4th ground wire (green) must be connected to the frame of the range with the ground screw. Failure

to do so can result in electrical shock, severe personal injury or death.

Follow the instructions for installing the conduit

under 3-Wire Connection: Conduit until the strain relief and bracket are installed. Do not install the conduit without a strain relief.

Loosen the 2 lower left and right screws from

the terminal block. Remove the lower 2 center screws. Do not discard any screws.

Remove the ground screw and bend the end of

the ground strap up so the slot is over the hole of the center screw removed in step 1.

Attach the ground (green) bare wire end to

the range frame and secure it in place with the ground screw.

Insert the bare wire (white/neutral) end through the

center terminal block opening. The center screw now attaches the bent up ground strap to the block.

Insert the two side bare wire ends into the left

and the right terminal block openings. Tighten the 3 screws securely into the terminal block. (approximately 35 - 50 IN-LB)

ENGLISH

Insert the two side bare wire ends into the lower

left and the lower right terminal block openings. Tighten the 3 screws securely into the terminal block. (approximately 35 - 50 IN-LB)

3-wire connection

Black White Red

Terminal block

Wire ends

Conduit connection plate

If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

4-wire connection

Black White Red

Terminal block

Ground

Wire ends

Conduit connection plate

Ground screw

If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

Ground wire

strap

Bend strap up and attach

INSTALLATION

Engaging the Anti-tip Device

%Move the range close enough to the opening to

plug into the receptacle.

%Slide the range into position ensuring that the back

leg slides under the anti-tip bracket. The range should sit flush against the back wall when properly installed.

%Carefully attempt to tip the range forward to ensure

that the anti-tip bracket is engaged properly. If properly installed, the anti-tip bracket will prevent the range from being tipped. If the range can be tipped, reinstall the range until the anti-tip bracket is properly installed and the range will not tip forward.

%Turn on electrical power. Check the range for

proper operation.

Installing the Rear Filler

Using a screwdriver, remove the upper four

screws that attach the rear bracket and loosen the lower two screws.

Place the rear filler on the rear bracket.

Tighten the two lower screws on the rear

bracket. Insert one of the screws removed in step 1 in the slot at each end of the rear filler.

Store the remaining two screws with these

instructions for future use.

Test Run

Check if the range is properly installed and run a test cycle.

Press Upper CLEAR/OFF and Lower CLEAR/

OFF to start test Turn each knob to the Hi position to check

that the surface heating elements are working properly. The elements should glow red and radiate heat, and they should cycle on and off periodically even when the knob is in the Hi position. This cycling prevents the glass-ceramic from being cracked by thermal shock. IMPORTANT : The Warming Zone does not consume enough power to glow red.

Optional Rear Filler

If the counter does not bridge the opening at the rear wall, use the rear filler kit provided with the slide-in range.

NOTE

If the countertop depth is greater than 25" there will be a gap between the filler kit and the back wall.

If the countertop depth is less than 24", the control panel will not sit flush with the countertop.

After checking all the surface heating elements,

check the locking system by pressing Lower CLEAR/OFF for three seconds. The oven door

should lock and the cooktop should not operate while the Lockout function is turned on. Press Lower CLEAR/OFF for three seconds to disable Lockout.

Now check the oven's operation. Turn the oven

mode knob to select the Bake mode. 350 °F appears in the display. Press Start.

The oven should finish preheating in 15 minutes,

and the convection fan should operate while the oven is preheating.

After checking the oven's operation, turn the

temperature up to 450 °F and leave the oven on for at least an hour to help remove any oil which might cause smoke and odors when first using the oven.

NOTE

Smoke may come out of the range when it is first used.

OPERATION

Control Panel Overview

3 4 5 6 7 8 9

Smart Diagnosis

Use during the Smart Diagnosis feature.

Cook Time / Clock

%Press the button to set the desired amount of time

for food to cook. The oven shuts off when the set cooking time runs out.

%Press and hold button for three seconds to set the

time of day.

Start Time / Setting

%Press the button to set the delayed timed cook. The

oven starts at the set time.

%Press and hold button for three seconds to select

and adjust oven settings.

Temp.

%Press the button to change the oven or meat probe

temperature during cooking.

Timer On/Off / Wi-Fi

%Press the button to set or cancel automatic timer. %Press and hold button for three seconds to connect

to Wi-Fi network.

/RZHU

8SSHU

/RZHU

5HPRWH

6WDUW

FRPPRQ

/RZHU

- /+

Press the plus button to increase cooking time or oven temperature. Press the minus button to decrease cooking time or oven temperature.

START / Oven Light

%Press the button to start all oven features. %Press the button to manually turn the oven light on/

off.

Upper CLEAR/OFF

Press the button to end all upper oven features.

Lower CLEAR/OFF / Lock Out

%Press the button to end all lower oven feature. %Press and hold button for three seconds to lock the

door and control panel.

Oven Mode Knob

Turn the knob to select oven operating mode.

ENGLISH

OPERATION

Knob Positions

After cleaning the oven knobs, make sure to replace each knob in the correct position. Failure to do so can result in improper operation of the burners.

Bridge

Dual Single Single Mode Single Triple

OPERATION

Changing Oven Settings

Clock

The clock must be set to the correct time of day in order for the automatic oven timing functions to work properly.

Press and hold Cook Time for three seconds.

CLO shows in the display. Press plus(+) or minus(-) to select the desired

time. Plus(+) to increase the time and minus(-) to decrease the time.

Press Start to enter the time and start the clock.

NOTE

%The time of day cannot be changed during a

timed baking or self-clean cycle.

%If no other keys are pressed within 25 seconds

of pressing Clock, the display reverts to the original setting.

%If the display colon in the clock is blinking, you

may have experienced a power failure. Reset the time.

Oven Light

The interior oven light automatically turns on when the door is opened. Press Oven Light to manually turn the oven light on.

NOTE

The oven light cannot be turned on if the Self Clean function is active.

Minimum & Maximum Default Settings

All of the features listed have a minimum and a maximum time or temperature setting that may be entered into the control. An entry acceptance beep sounds each time a control key is pressed.

An entry error tone (two short tones) sounds if the entry of the temperature or time is below the minimum or above the maximum setting for the feature.

Feature

Clock

Timer

Cook Time

Conv. Bake

Conv. Roast

Speed Broil & Broil

min.

Temp. /

Time

12 Hr.

24 Hr.

12 Hr. 0:10 min.

24 Hr. 0:10 min.

12 Hr. 1:00 min.

24 Hr. 1:00 min.

1:00

Hr. / min.

0:00

Hr. / min.

300 °F /

150 °C

300 °F /

150 °C

400 °F

max.

Temp. /

Time