9 Installation Overview
10 Specifications
11 Unpacking Your Refrigerator
11 Choosing the Proper Location
11 - Flooring
12 - Ambient Temperature
12 - Measuring the Clearances
12 Removing/Assembling the Doors
17 Connecting the Water Line
17 - Before You Begin
18 - Water Pressure
18 - What You Will Need
19 - Water Line Installation Instructions
20 Turning On the Power
21 Leveling
21 Door Alignment
21 - Refrigerator Door Alignment
22 - Freezer Door Alignment
35 Storing Food
35 - Food Preservation Location
36 - Food Storage Tips
36 - Storing Frozen Food
37 Adjusting the Refrigerator Shelves
37 - Detaching the Shelf
37 - Assembling the Shelf
38 - Using the Folding Shelf
38 - When Closing the Door
39 Big Fresh Zone
39 - Removing the Big Fresh Zone drawer
39 - Assembling the Big Fresh Zone drawer
40 Removing/Assembling the Fresh Zone
compartment
42 EasyReach™
42 Dairy Corner
42 Door-in-Door
43 - Removing the Door-In-Door Compartment
44 Mini Table
44 - Removing the Mini Table
44 - Assembling the Mini Table
45 EasyLift Bin
45 Freezer Drawer
45 - Removing the Freezer Drawer
46 - Assembling the Freezer Drawer
46 Refrigerator/Freezer Door Bins
47 MAINTENANCE
47 Cleaning
48 Replacing the Fresh Air Filter
49 Replacing the Water Filter
23 HOW TO USE
23 Before Use
24 Control Panel
24 - Control Panel Features
27 Smart Features
31 In-Door Ice Bin
31 - Detaching the In-Door Ice Bin
31 - Assembling the In-Door Ice Bin
32 Automatic Icemaker
34 Ice and Water Dispenser
53 SMART DIAGNOSIS™
53 Using Smart Diagnosis™
54 TROUBLESHOOTING
64 WARRANTY
ENGLISH
PRODUCT FEATURES
PRODUCT FEATURES
3
* Depending on the model, some of the following functions may not be available.
DOOR ALARM
The Door Alarm function is designed to prevent refrigerator malfunctioning
that could occur if a refrigerator door or freezer door remains open. If a
refrigerator door or freezer door is left open for more than 60 seconds, a
warning alarm sounds at 30 second intervals until it is closed.
AUTO CLOSING HINGE
The refrigerator doors close automatically with a slight push. (The door only
closes automatically when it is open at an angle less than 30°.)
ICE PLUS
Ice production can be increased by approximately 20 percent when the
freezer section is maintained at the coldest temperature for a 24-hour
period.
FILTERED WATER AND ICE DISPENSER
The water dispenser dispenses fresh, chilled water.
The ice dispenser dispenses cubed and crushed ice.
4
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
This guide contains many important safety messages. Always
This is the safety alert symbol. It alerts you to safety messages that inform you of
hazards that can kill or hurt you or others, or cause damage to the product.
All safety messages will be preceded by the safety alert symbol and the hazard
signal word WARNING or CAUTION. These words mean:
WARNING
CAUTION
You can be killed or seriously injured if you do not follow instructions.
Indicates an imminently hazardous situation which, if not avoided, may result
in minor or moderate injury, or product damage.
read and obey
all safety messages.
WARNING
To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety
precautions should be followed, including the following:
Power
yNEVER unplug your refrigerator by pulling on the power cord. Always grip the plug firmly and pull it straight
out from the outlet.
yIf the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard. Do not use a cord that shows cracks or abrasion damage along its
length or at either the plug or connector end.
yDo not use an uncertified power outlet.
yUnplug the power plug immediately in the event of a blackout or thunderstorm.
yPlug in the power plug with the power cord facing downward.
Installation
yContact an authorized service center before you install or relocate the refrigerator.
yWhen moving your refrigerator away from the wall, be careful not to roll over or damage the power cord.
yPrior to use, ensure that you are connecting this product to a dedicated, grounded electrical outlet rated for
use with this product (115V, 60Hz, AC only). It is the user’s responsibility to replace a standard 2-prong wall
outlet with a standard 3-prong wall outlet.
yDo not install the refrigerator where there may be a danger of the unit falling.
Use
yDO NOT allow children to climb, stand, or hang on the refrigerator doors or on the shelves in the
refrigerator. They could damage the refrigerator and seriously injure themselves.
yDo not hang on to or place heavy objects on the refrigerator’s dispenser.
yDo not place heavy or dangerous objects (bottles with liquid) on the refrigerator.
yDo not put live animals inside the refrigerator.
yDo not allow children to climb into the product when it is in use.
yIn the event of a gas leak (propane/LPG), ensure adequate ventilation and contact an authorized service
center before resuming use. Do not touch or disassemble the electric outlet of the refrigerator.
yIn the event of a refrigerant leak, move flammable objects away from the refrigerator. Ensure adequate
ventilation and contact an authorized service center.
yDo not use or place flammable substances (chemicals, medicine, cosmetics, etc) near the refrigerator or
store them inside the refrigerator. Do not place the refrigerator in the vicinity of flammable gas.
yDo not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or personal
injury if items are removed with excessive force.
yDo not open the door of the appliance with the door in door open, or do not open the door in door while the
door of the appliance is open. The door in door may be struck by the edge of the appliance and damaged.
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
5
To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety
precautions should be followed, including the following:
yThis product is not to be used for special purposes such as the storage of medicine or test materials
or for use on ships, etc.
yUnplug the power plug before cleaning or repairing the refrigerator.
yWhen you replace the light bulb in the refrigerator, unplug the refrigerator or turn off the power.
yDo not modify or extend the power cord.
yDo not use a dryer to dry the interior. Do not light a candle to remove interior odors.
yFor your safety, this appliance must be properly grounded. Have the wall outlet and the circuit
checked by a qualified electrician to make sure the outlet is properly grounded.
yDo not use an outlet that can be turned off with a switch. Do not use an extension cord. It is the
user’s responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.
yDo not, under any circumstances, cut or remove the third (ground) prong from the power cord.
yDo not use an adapter plug and plug the power plug into a multi-outlet extension cord.
yDisconnect the power cord immediately if you hear a noise, smell a strange odor or detect smoke
coming from the appliance.
yTurn the power off if water or dust penetrates into the refrigerator. Call a service agent.
yDo not disassemble or modify the refrigerator.
yDo not put hands, feet, or metal objects below or behind the refrigerator.
yDo not operate the refrigerator or touch the power cord with wet hands.
yIn refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector
mechanism or with the heating element that releases the cubes. Do not place fingers or hands on the
automatic ice-making mechanism while the refrigerator is plugged in.
yWhen dispensing ice from the dispenser, do not use crystal ceramics.
yDo not touch the cold surfaces in the freezer compartment with wet or damp hands, when your
refrigerator is in operation.
yDo not put glass containers, glass bottles or soda in the freezer.
yThis appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by a person responsible for their safety.
yDo not refreeze frozen food that has thawed completely. Doing so may result in a serious health
issue.
yIf you are throwing away your old refrigerator, make sure the CFC coolant is removed for proper
disposal by a qualified servicer. If you release CFC coolant, you may be fined or imprisoned in
accordance with the relevant environmental law.
yJunked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. When
disposing of the refrigerator, remove the packing materials from the door or take off the doors but
leave the shelves in place so that children may not easily climb inside.
yIf connected to a circuit protected by fuses, use time delay fuse.
WARNING
This product contains chemicals known to the State of California to cause cancer and birth defects
or other reproductive harm.
Wash hands after handling.
6
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety
precautions should be followed, including the following:
CAUTION
Installation
yThe refrigerator must be properly installed in accordance with the Installer Instructions that were
taped to the front of the refrigerator.
yBe careful when you unpack and install the refrigerator. Immediately dispose of plastic and other
packing materials out of reach of children.
yThe appliance must be positioned for easy access to a power source.
Use
yClose the door carefully when children are around.
yKeep fingers out of pinch point areas; clearances between the doors and cabinets are
necessarily small. Be careful closing doors when children are nearby.
yIf you store food improperly, be aware that it may fall and cause injury.
yDo not use aerosols near the refrigerator.
yDo not store articles on the top of the appliance.
Maintenance
yDo not use strong detergents like wax or thinners for cleaning. Clean with a soft cloth.
yWipe foreign objects (such as dust and water) off the prongs of the power plug and contact
areas regularly.
yDo not store, disassemble or repair the refrigerator by yourself.
yRemove any dust or foreign matter from the power plug pins.
yDo not use a wet or damp cloth when cleaning the plug.
yIf the refrigerator is disconnected from the power supply, you should wait for at least five
minutes before plugging it back in.
yIf you notice a chemical or burning plastic smell or see smoke, unplug the refrigerator
immediately and contact your LG Electronics Service Center.
SAVE THESE INSTRUCTIONS
ENGLISH
COMPONENTS
COMPONENTS
7
Use this page to become more familiar with the parts and features of your refrigerator.
*The appearance and specifications of the actual product may differ depending on the model.
Refrigerator Exterior
LED Display
Displays the refrigerator and
freezer’s target temperatures,
the water filter condition and the
dispenser status.
Control Panel
Sets the refrigerator and freezer
temperatures, the water filter
condition and the dispenser mode.
Filtered Water and
Ice Dispenser
Dispenses purified water and ice.
Refrigerator
Preserves food.
Door in Door
Release Button
Freezer
Preserves frozen food.
8
ENGLISH
COMPONENTS
Refrigerator Interior
Adjustable Refrigerator Shelf
The shelves in your refrigerator are adjustable
to meet your individual storage needs.
Bluetooth Speaker*
LED Interior Lamp
The interior lamps light up
the inside of the refrigerator.
Refrigerator
Bin
Indoor Ice Bin
Ice cubes are
automatically
produced.
Big Fresh Zone
Freezer Bin
Dairy Corner
Used to preserve dairy products.
Cheese & Butter Bin
Cheese & butter and
Condiment bins, that
are specially designed
for these items, making
spreading butter and
slicing cheese easier.
Door-In-Door Case
A convenient storage area
for frequently-used items
that require easy access
Condiment Bin
Big Fresh Zone
EasyReach™
You can store small items,
or defrost an item.
Freezer Bin
* on some models
Freezer
Drawer
Freezer
Drawer
ENGLISH
INSTALLATION
INSTALLATION
9
Installation Overview
Please read the following installation instructions first after purchasing this product or transporting
it to another location.
1 Unpacking your
refrigerator
4 Connecting the
water supply and
water line
2 Choosing the proper
location
5 Leveling and Door
Alignment
3 Disassembling/Assembling
NOTE
Connect to potable water supply only.
ENGLISH
10
INSTALLATION
Specifications
The appearance and specifications listed in this manual may vary due to constant product
improvements.
Bottom-freezer refrigerator model LNXS30866*
DescriptionFrench door refrigerator
Electrical requirements115 VAC @ 60 Hz
Min./Max. Water pressure
Dimensions
Net weight377 lb. (171 kg)
Bottom-freezer refrigerator model LNXC23766*, LNXC23726*
DescriptionFrench door refrigerator
Electrical requirements115 VAC @ 60 Hz
Min./Max. Water pressure
Dimensions
Net weight335 lb. (152 kg)
20 - 120 psi (138 - 827 kPa)
35 7/8' (W) X 36 3/8' (D) X 70 1/2' (H), 49 3/4' (D w/ door open)
912 mm (W) X 923 mm (D) X 1790 mm (H), 1263 mm (D w/ door open)
20 - 120 psi (138 - 827 kPa)
35 7/8' (W) X 29 7/8' (D) X 70 1/2' (H), 43 1/4' (D w/ door open)
912 mm (W) X 758 mm (D) X 1790 mm (H), 1098 mm (D w/ door open)
INSTALLATION
ENGLISH
11
Unpacking Your Refrigerator
WARNING
yUse two or more people to move and
install the refrigerator. Failure to do so
can result in back or other injury.
yYour refrigerator is heavy. When moving
the refrigerator for cleaning or service,
be sure to protect the floor. Always pull
the refrigerator straight out when moving
it. Do not wiggle or walk the refrigerator
when trying to move it, as floor damage
could occur.
yKeep flammable materials and vapors,
such as gasoline, away from the
refrigerator. Failure to do so can result in
fire, explosion, or death.
Remove tape and any temporary labels from your
refrigerator before using. Do not remove any
warning-type labels, the model and serial number
label, or the Tech Sheet that is located under the
front of the refrigerator.
To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue residue
can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with
your fingers. Wipe with warm water and dry.
Choosing the Proper Location
ySelect a place where a water supply can
be easily connected for the automatic
icemaker.
NOTE
The water pressure must be 20~120
psi or 138~827 kPa or 1.4~8.4 kgf/cm²
on models without a water filter and
40~120 psi or 276~827 kPa or 2.8~8.4
kgf/cm² on models with a water filter.
yThe refrigerator should always be plugged
into its own individual properly grounded
electrical outlet rated for 115 Volts, 60 Hz,
AC only, and fused at 15 or 20 amperes.
This provides the best performance
and also prevents overloading house
wiring circuits which could cause a fire
hazard from overheated wires. It is
recommended that a separate circuit
serving only this appliance be provided.
WARNING
To reduce the risk of electric shock, do not
install the refrigerator in a wet or damp
area.
Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator.
Refrigerator shelves are installed in the shipping
position. Please reinstall shelves according to
your individual storage needs.
Flooring
To avoid noise and vibration, the unit must be
leveled and installed on a solidly constructed
floor. If required, adjust the leveling legs to
compensate for unevenness of the floor. The
front should be slightly higher than the rear to
aid in door closing. Leveling legs can be turned
easily by tipping the cabinet slightly. Turn the
leveling legs to the left to raise the unit or to
the right to lower it. (See Leveling and Door
AlIgnment.)
NOTE
Installing on carpeting, soft tile surfaces,
a platform or weakly supported structure
is not recommended.
12
ENGLISH
INSTALLATION
Ambient Temperature
Install this appliance in an area where the
temperature is between 55°F (13°C) and 110°F
(43°C). If the temperature around the appliance
is too low or high, cooling ability may be
adversely affected.
Measuring the Clearances
Too small of a distance from adjacent items
may result in lowered freezing capability and
increased electricity consumption charges.
Allow at least 24 inches (61 cm) in front of the
refrigerator to open the doors, and at least
2 inches (5.08 cm) between the back of the
refrigerator and the wall.
24” (61 cm)
Removing/Assembling the Doors
Removing the Left Refrigerator Door
The water supply is connected to the
1
upper right part of the rear surface of the
refrigerator. Remove the ring in the joint
area. Hold the water supply connection
and gently push the Collet to detach the
water supply line as shown in
Collet
NOTE
Detachment of the water supply line is
applicable only when detaching the left
refrigerator door.
.
2” (5.08 cm)
Remove the screw from the hinge cover
2
at the top of the refrigerator. Lift the hook
(not visible), located at the bottom of the
front side of the cover
screwdriver.
with a flat-head
INSTALLATION
ENGLISH
13
Remove the cover and pull out the tube .
3
Disconnect all wire harnesses
Rotate the hinge lever counterclockwise
4
. Lift the top hinge free of the hinge
lever latch.
Hinge Lever Latch
CAUTION
When lifting the hinge free of the latch, be
careful that the door does not fall forward.
.
Removing the Right Refrigerator
Door
Remove the top hinge cover screw .
1
Lift the hook (not visible), located at the
bottom of the front side of the cover
with a flat-head screwdriver.
Detach the wire harness .
2
,
Lift the door from the middle hinge pin and
5
remove the door.
CAUTION
Place the door, inside facing up, on a
non-scratching surface.
Rotate the hinge lever clockwise.
3
Lift the top hinge
lever latch.
CAUTION
When lifting the hinge free of the hinge
lever latch, be careful that the door
does not fall forward.
free of the hinge
Hinge Lever Latch
14
ENGLISH
INSTALLATION
Lift the door from the middle hinge pin and
4
remove the door.
CAUTION
Place the door, inside facing up, on a
non-scratching surface.
Removing the Freezer Doors
Remove the two hinge bolts.
1
Assembling the Freezer Doors
Lower the door onto the lower hinge pin.
1
Lower hinge
Position the middle hinge pin in place to
2
hold the door and insert the two hinge
bolts.
Tighten the two hinge bolts.
3
Rotate the hinge out of the way so that the
2
door can be lifted off.
Remove the door by raising it from the
3
lower hinge.
Lower hinge
INSTALLATION
ENGLISH
15
Assembling the Right Refrigerator Door
Install the right-side door first.
Make sure that the plastic sleeve is
1
inserted in the bottom of the door. Lower
the door onto the middle hinge pin as
shown in the figure.
Fit the hinge over the hinge lever latch
2
and slot it into place. Rotate the lever
counterclockwise to secure the hinge.
Hinge Lever Latch
Connect the wire harness .
3
Make sure that the door-switch located
4
inside the cover is tightly connected.
Position the cover in its place. Insert and
tighten the cover screw
.
16
ENGLISH
INSTALLATION
Assembling the Left Refrigerator
Door
Install the left refrigerator door after the right
door is installed.
Make sure that the plastic sleeve is
1
inserted in the bottom of the door. Install
the refrigerator door onto the middle hinge.
Fit the hinge over the hinge lever latch
2
and slot it into place. Rotate the lever
clockwise
Hinge Lever Latch
and fasten the hinge.
Push the water supply tube into the hole
4
on the top case and pull it through the
backplate.
Hold the water supply connection and
5
gently push in the collet to connect the
water supply line as shown in
the tube at least
connector.
5
/8 inch (15 mm) into the
Collet
. Insert
Connect all the wire harnesses.
3
Make sure that the door-switch located
6
inside the cover is tightly connected. Place
the cover
cover screw .
in its position and tighten the
INSTALLATION
ENGLISH
17
NOTE
Collet
Tube
Insert Line
1) Gently insert the tube until only one
line shows on the tube.
(Correct)
(Incorrect)
2) Pull the tube to make sure that the
tube is tightly fastened.
Connecting the Water Line
Before You Begin
This water line installation is not covered by the
refrigerator warranty. Follow these instructions
carefully to minimize the risk of expensive water
damage.
Water hammer (water banging in the pipes) in
house plumbing can cause damage to refrigerator
parts and can lead to water leakage or flooding.
Call a qualified plumber to correct water hammer
before installing the water supply line to the
refrigerator.
CAUTION
To prevent burns and product damage,
only connect the refrigerator water line to
a cold water supply.
If you use your refrigerator before connecting
the water line, make sure the icemaker power
switch is in the OFF (O) position.
CAUTION
Do not install the icemaker tubing in
areas where temperatures fall below
freezing.
18
ENGLISH
INSTALLATION
Water Pressure
The water pressure must be 20~120 psi or
138~827 kPa or 1.4~8.4 kgf/cm² on models
without a water filter and 40~120 psi or 276~827
kPa or 2.8~8.4 kgf/cm² on models with a water
filter.
If a reverse osmosis water filtration system is
connected to your cold water supply, this water
line installation is not covered by the refrigerator
warranty. Follow the instructions carefully to
minimize the risk of expensive water damage.
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs
to be a minimum of 40 to 60 psi (276~414 kPa or
2.8~4.2 kgf/cm², less than 2.0~3.0 sec. to fill a
cup of 7 oz or 198 cc capacity).
CAUTION
Wear eye protection during installation
to prevent injury.
If the water pressure from the reverse osmosis
system is less than 20 psi or 138 kPa or 1.4 kgf/
cm² (takes more than 4.0 sec to fill a cup of 7 oz
or 198 cc capacity):
yCheck to see if the sediment filter in
the reverse osmosis system is blocked.
Replace the filter if necessary.
yAllow the storage tank on the reverse
osmosis system to refill after heavy
usage.
yIf the issue concerning water pressure
from reverse osmosis remains, call a
licensed, qualified plumber.
yAll installations must be in accordance
with local plumbing code requirements.
What You Will Need
yCopper Tubing,
connect the refrigerator to the water
supply. Be sure both ends of the tubing
are cut square.
yTo determine how
much tubing you need:
measure the distance
from the water valve on the back of
the refrigerator to the water supply
pipe. Then, add 8 feet (2.4 m). Be sure
there is sufficient extra tubing (about 8
feet [2.4 m] coiled into 3 turns of about
10 in. [25 cm] diameter) to allow the
refrigerator to move out from the wall
after installation.
yPower drill.
y½ in. or adjustable
wrench.
yFlat blade and Phillips
head screwdrivers.
yTwo ¼ in. outer
diameter compression
nuts and 2 ferrules (sleeves)
copper tubing to the shutoff valve and
the refrigerator water valve.
yIf your existing copper water line has a
flared fitting at the end, you will need
an adapter (available at plumbing supply
stores) to connect the water line to the
refrigerator OR you
can cut off the flared
fitting with a tube
cutter and then use a
compression fitting.
yShutoff valve
water line. The shutoff valve should
have a water inlet with a minimum
inside diameter of 5/32 in. at the point of
connection to the COLD WATER LINE.
Saddle-type shutoff valves are included
in many water
supply kits. Before
purchasing, make
sure a saddle-type
valve complies with
your local plumbing codes.
¼ in. outer diameter, to
to connect the
to connect to the cold
NOTE
A self piercing saddle type water valve
should not be used.
INSTALLATION
ENGLISH
19
Water Line Installation Instructions
WARNING
When using any electrical device
(such as a power drill) during
installation, be sure the device is
battery powered, double insulated
or grounded in a manner that will
prevent the hazard of electric shock.
Install the shutoff valve on the nearest
frequently used drinking water line.
SHUT OFF THE MAIN WATER SUPPLY
1
Turn on the nearest faucet to relieve the
pressure on the line.
CHOOSE THE VALVE LOCATION
2
Choose a location for
the valve that is easily
accessible. It is best to
connect into the side of a
vertical water pipe. When
it is necessary to connect
into a horizontal water
pipe, make the connection to the top or
side, rather than at the bottom, to avoid
drawing off any sediment from the water
pipe.
DRILL THE HOLE FOR THE VALVE
3
Drill a ¼ in. hole in
the water pipe using
a sharp bit. Remove
any burrs resulting
from drilling the hole
in the pipe. Be careful
not to allow water
to drain into the drill. Failure to drill a ¼ in.
hole may result in reduced ice production
or smaller cubes.
NOTE
The hookup line cannot be white, plastic
tubing. Licensed plumbers must use
only copper tubing (NDA tubing #49595
or #49599) or Cross Link Polyethylene
(PEX) tubing.
FASTEN THE SHUTOFF VALVE
4
Fasten the shutoff valve to the cold water
pipe with the pipe clamp.
Pipe Clamp
Saddle-Type
Shutoff Valve
Vertical Cold
Water Pipe
NOTE
Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered
to. Saddle valves are illegal and their use is
not permitted in Massachusetts. Consult
with your licensed plumber.
TIGHTEN THE PIPE CLAMP
5
Tighten the clamp screws until the sealing
washer begins to swell.
Do not overtighten the clamp or
NOTE:
you may crush the tubing.
Washer
Pipe Clamp
Clamp Screw
ROUTE THE TUBING
6
Route the tubing between the cold water
line and the refrigerator.
Route the tubing through a hole drilled in
the wall or floor (behind the refrigerator or
adjacent base cabinet) as close to the wall
as possible.
NOTE
Be sure there is sufficient extra tubing
(about 8 feet coiled into 3 turns of
about 10 in. diameter) to allow the
refrigerator to move out from the wall
after installation.
Inlet End
20
ENGLISH
INSTALLATION
CONNECT THE TUBING TO THE VALVE
7
Place the compression nut and ferrule
(sleeve) for the copper tubing onto the
end of the tubing and connect it to the
shutoff valve. Make sure the tubing is
fully inserted into the valve. Tighten the
compression nut securely.
Saddle-Type
Shutoff Valve
Packing Nut
Outlet Valve
FLUSH OUT THE TUBING
8
Turn the main water
supply on and flush out
the tubing until the water
is clear.
Shut the water off at the
water valve after about
one quart of water has
been flushed through the tubing.
CONNECT THE TUBING TO THE
9
REFRIGERATOR
Before making the connection
NOTE:
to the refrigerator, be sure that the
refrigerator power cord is not plugged into
the wall outlet.
a. Remove the plastic flexible cap from the
water valve.
b. Place the compression nut and ferrule
(sleeve) onto the end of the tubing as
shown.
c. Insert the end of the copper tubing into
the connection as far as possible. While
holding the tubing, tighten the fitting.
Compression
Nut
Ferrule (sleeve)
TURN THE WATER ON AT THE SHUTOFF
10
VALVE
Tighten any connections that leak.
CAUTION
Check to see if leaks occur at the water
line connections.
PLUG IN THE REFRIGERATOR
11
Arrange the coil of tubing so that it
does not vibrate against the back of the
refrigerator or against the wall. Push the
refrigerator back to the wall.
START THE ICEMAKER
12
Turn the icemaker ON at the control panel.
The icemaker will not begin to operate
until it reaches its operating temperature
of 15°F (–9°C) or below. It will then begin
operation automatically if the icemaker has
been turned ON.
Turning On The Power
Plug in the refrigerator.
Tubing Clamp
¼ in.
Compression
Nut
Ferrule
(sleeve)
¼ in. Tubing
Refrigerator
Connection
CAUTION
yConnect to a rated power outlet.
yHave a certified electrician check
the wall outlet and wiring for proper
grounding.
yDo not damage or cut off the ground
terminal of the power plug.
INSTALLATION
ENGLISH
21
Leveling
After installing, plug the refrigerator’s power
cord into a 3-prong grounded outlet and push
the refrigerator into the final position.
The refrigerator has two front leveling legs—
one on the right and one on the left. Adjust the
legs to alter the tilt from front-to-back or sideto-side. If the refrigerator seems unsteady, or
you want the doors to close more easily, adjust
the refrigerator’s tilt using the instructions
below:
Turn the leveling leg to the left to raise
1
that side of the refrigerator or to the right
to lower it. It may take several turns of the
leveling leg to adjust the tilt of the
refrigerator.
NOTE
A flare nut wrench works best, but an
open-end wrench will suffice.
Do not over-tighten.
Open both doors again and check to make
2
sure that they close easily. If the doors do
not close easily, tilt the refrigerator slightly
more to the rear by turning both leveling
legs to the left. It may take several more
turns, and you should turn both leveling
legs the same amount.
Door Alignment
Leveling the doors may not be possible when
the floor is not level, or is of weak or poor
construction. The refrigerator is heavy and
should be installed on a rigid and solid surface.
Some wood flooring may cause leveling
difficulties if it flexes excessively.
Refrigerator Door Alignment
yIf either refrigerator door is lower, open the
door, lift it, and turn the hinge bolt using the
wrench as shown. (For upper refrigerator
doors, use wrench
(LNXS30866*/LNX23766*)
yIf the right side door is lower, lift the right
side door, and use a pair of long nose pliers
(not supplied) to additionally insert a snap
3
ring
as shown in the drawing, until the
heights are balanced.
Refrigerator
left hand door
Refrigerator
right hand door
1
.)
Height difference
(LNXC23726*)
Refrigerator
right hand door
(LNXS30866*/LNX23766*)
ENGLISH
22
INSTALLATION
Freezer Door Alignment
yMethod 1 is recommended.
yFor freezer doors, use wrench
Height difference
(Method 1)
1
Open the door, and adjust the height by
tightening the nut above the foot with the
wrench
2
.
Raise door
2
.
Method 2, only allows a maximum of 3mm
(
2
of adjustment)
(1) Use the wider side of the number
wrench to unscrew the locking nut.
Unscrew nut
(2) Use the narrower side of the wrench to
turn the adjustment hinge pin (
clockwise or ( ) counterclockwise,
and adjust the gap difference between the
refrigerator and the freezer door.
Locking nut
Adjustment
hinge pin
Lower door
2
)
Wrench
Lower door
Raise door
(3) After the door heights are adjusted,
completely tighten the locking nut by
turning it (
CAUTION
Do not adjust the hinge pin height level
too much. The hinge pin can fall out.
(Maximum height adjustment: 3mm)
) counterclockwise.
Tighten nut
Loading...
+ 49 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.