LG LNV7210R User guide

Specication

OWNER’S MANUAL

High
Denition
Network
Camera

Please read this manual carefully before operating
your set and retain it for future reference.

MODEL
LNV7210 series LNV7210R series

Camera

Video /
Audio

Event

Item LNV7210R series LNV7210 series

Image Device 6.4 mm (1/2.8 Type) CMOS

Lens Type 3 mm to 9 mm F1.2 (x3 Zoom)

Day / Night ICR (Auto / Day / Night / External / Schedule)

Minimum
Illumination

WDR Support

IR Distance
(LNV7210R only)

Image
Enhancement

Compression H.264, H.264_High, MJPEG

Resolution 1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)

Maximum Frame
Rate

Multi-Streaming Up to 4

ROI (Region of
Interest)

Video Analytics

Text Overlay Support

Audio
Compression

2-way Audio Support

Audio Detection Support

Event Trigger Video analytics, Audio detection, Alarm input

Event Notication Relay Out, Email, FTP

Pre Event
Buering

Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)

B/W: 0 lx @ IR LED on

20 m

Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control,
AGC, White Balance, Privacy Masking, Sharpness, EIS, Pivot,
SmartIR (LNV7210R only)

60 fps @ 1920 x 1080

Smart codec (Up to 8)

Motion detection, Tampering alarm, Face detection, Intrusion
detection, Crossing line, Object counting, Object removal, Object
desertion

G.711, G.726

Support

B/W: 0.003 lx @ F1.2
(1/30 sec, 50 IRE)

Analog Out BNC out

Interface

Network

General

Note that design and specication of this unit may change from the manual as quality and
improvement without prior notice.

Components

Camera, CD (Software and Owner’s Manual), Installation Manual, Test monitor cable, Wrench,
Screws (4 EA), Installation sticker, Camera mounting bracket

Audio In / Out 1 / 1

Alarm In / Out 1 In / 1 Out

SD Slot micro SD (Up to 32 GB)

Ethernet RJ-45 10 / 100 BASE-T

Security Password protection, HTTPS (SSL, TLS), IP ltering, IEEE 802.1X

Open Protocol ONVIF 2.2 Prole S, PSIA 1.1

IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP,

Protocol

Integrated
Software

Connections Up to 20

Power Source DC 12 V, PoE

Maximum Power
Consumption

Maximum Input
Current

Operation
Temperature /
Humidity

Protection IK10, IP66

Dimension
(Ø x H)

Weight 957 g 950 g

QoS, UPnP

IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)

LG Ipsolute VMS Suite / Mobile application (iPhone, iPad,
Android)

8.7 W (DC 12 V), 10.4 W (PoE 48 V)

730 mA (DC 12 V), 280 mA (PoE)

-10 ºC to 50 ºC / 0 % RH to 80 % RH

140 mm x 122 mm

*MFL69458110*

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.
Warning: Please adopt the power adapter which can meet the safety extra low voltage (SELV)

standard. And source with DC 12 V or
AC 24 V (depending on models) according to the IEC60950-1 and Limited Power Source standard.

Warning: Install the camera on a ceiling or wall
where can withstand the weight of 5 times of
the camera including mounting bracket.

Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.

Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.

Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be placed
on the apparatus.

Caution: Make sure the power supply voltage
is correct before using the camera.

Caution: Do not drop the camera or subject it
to physical shock.

Caution: The sensor may be burned out by
a laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.

Caution: While shipping, the camera should be
packed in its original packing.

Caution: It is permitted to use ancillary
equipment (e.g. A UPS) to prevent the damage
from mains supply voltage reductions.

Note:

Please make sure the product is installed
appropriate places where secured from flood,
such as under the eaves, to operate properly.
This product is certified as IP66 standard.
However, if there is any flood concerns, it
is highly recommended to use an outdoor
Housing. When you install the camera inside
an outdoor Housing, please use one of the
following methods:

1. Remove the front glass of Housing before
installing the camera.

2. To keep the front glass of Housing, remove
the front cover, and then put the camera
close to the front glass.

Disposal of your old appliance

1. This crossed-out
wheeled bin symbol
indicates that waste
electrical and electronic
products (WEEE)
should be disposed
of separately from the
municipal waste stream.

2. Old electrical products can contain
hazardous substances so correct disposal
of your old appliance will help prevent
potential negative consequences for the
environment and human health. Your old
appliance may contain reusable parts that
could be used to repair other products,
and other valuable materials that can be
recycled to conserve limited resources.

3. You can take your appliance either to the
shop where you purchased the product,
or contact your local government waste
office for details of your nearest authorised
WEEE collection point. For the most up to
date information for your country please
see www.lg.com/global/recycling

EuSP Ltd.
Herald Way Pegasus Business Park
Castle Donington, DE74 2TZ United Kingdom

Important Safety
Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.

8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.

9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.

10. Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.

11. Only use attachments/accessories
specified by the manufacturer.

12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.

13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.

14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.

Handling of the unit

Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail
or to get cause of fire or electric shock.

• Remove dust or dirt on the surface of the
lens with a blower.

• Use a soft and lint-free, dry cloth(such as
glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.

• Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.

• This camera is designed for mounting on
the ceiling or wall. If you install this camera
upside down, it may cause malfunction.

Operating and storage
location

Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.

• Extremely hot or cold places (operating
temperature -10 °C to 50 °C, however, we
recommend that the unit be used within a
temperature range of 0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful

electromagnetic radiation such as radio or
TV transmitters.

• Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.

Part Names and Functions

Connection

a

b
c

d
e
f
g

l

h i jk

a Dome Cover

b IR Sensor (LNV7210R only)

IR LED (LNV7210R only)

c

NOTE:

Do not stare at operating IR LED within hazard distances (1 m).

micro SD card slot

d

Insert the micro SD card.

Jog button

e

Use this button for control the Zoom / Focus of the camera.

Video Out Connector

f

Use this jack for checking the picture with portable monitor when install the camera.

RESET button

g

Push the button more than 3 seconds, this would restore the factory default network related
settings.

AUDIO IN / OUT (Line Level Input/ Output)

h

i ALARM IN & OUT / ALARM IN & OUT RETURN

Provides physical interface for sensor and Alarm/Relay.

Power input terminal

j

Connects to a DC 12 V power supply using proper cables. This camera must always be
operated a DC 12 V. Certified/Listed Adaptor which comply with LPS.

ETHERNET / PoE Port

k

Connects to a PC or a network via a hub with a 10 BASE-T / 100 BASE-TX cable attached
RJ-45 connector.

NOTE:

Power over Ethernet (PoE) is a technology that integrates power into a standard LAN
infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates the need for
power outlets at the device locations and enables easier application of uninterruptible power
supplies (LPS).

Camera mounting bracket

l

You can lock the camera mounting bracket by tighten the screws.

Precautions

• Be sure to switch off the unit before
installation and connection.

• The installation should be made by
qualified service personnel or system
installers.

• Do not expose the power and connection
cables to moisture, which may cause
damage to the unit.

Connecting Network

You can control and monitor the system via
network. With the remote control (monitoring),
you can change the system configuration
or monitor the image via network. After the
installation, check the network settings for the
remote control and monitoring work.
Connect the IP camera to your network using a
standard RJ-45 network cable as shown below.

PoE Device

(IEEE802.3af)

Broadband

Service

Router

Broadband

Service

Connecting Power Source

Connect power, using one of the methods
listed below:

To use the power adapter

Connect a DC 12 V power source to the power
input terminal as shown below.
(recommended power adapter is DC 12 V / 1.5
A or above)

NOTE:

• When the connecting Alarm and Audio,
tighten the screws as shown above.

• Put your finger between the power
connector and the camera body to pull
out the connector.

To use the PoE (Power over Ethernet)
device

Connect the PoE cable to the LAN port on the
unit. You must use the “IEEE802.3af” standard
PoE device.

PoE Device

(IEEE802.3af )

NOTE:

If the camera doesn’t work properly after
connecting PoE device, please check if the PoE
device supplies enough power.

Connecting Alarm Device

Alarm terminals are used to connect the alarm
(relay) devices such as sensors, door switches,
etc.

ALARM IN & OUT / ALARM IN & OUT RETURN
(Sensor Input / Relay Output)

Connect the sensor device and alarm (relay)
device to the alarm terminal. Alarm signal is
outputted at an event occurrence.

Alarm (relay)
Device

Sensor
Device

NOTE:

• The Photo MOS Relay is rated for 100 mA
at DC 20 V or 100 mA at AC 28 V.

• Grasp both ends of the 3 or 4 pin
connector plug and then sway both side
to pull it out.

Connecting Microphone and
Speaker Device

Optionally connect an active speaker and/or
external microphone with a built-in amplifier.

AUDIO OUT

AUDIO IN

NOTE:

Keep the microphone away from the speaker
to avoid howling.

Installation

Using the micro SD card

You can record your surveillance environment with the micro SD
card even if the network is disconnected condition.

To insert the micro SD card

1. Remove the Dome Cover.

2. Insert the micro SD card carefully as shown in the following
illustrations. Make sure the micro SD card terminal position
before insert the micro SD card. Push the back end of the
micro SD card to fix it at the last step.

NOTE:

• Do not use the power too much when you insert the micro
SD card. The micro SD card may be damaged.

• If you insert the micro SD card in the wrong position,
the micro SD card may be damaged or it may cause the
malfunction of the micro SD Card Slot.

• Keep the terminal part of the micro SD card in clean. Be
careful the terminal part of the micro SD card not to dusty.

• As the micro SD card is consumable, the micro SD card end
its days and may be not able to save data if you use it more
than over certain times. In this case, replace micro SD card
to buy a new one.

*MFL69458110*

Remove the micro SD card

1. Press the back end of the micro SD card to release the lock
condition.

2. Take the micro SD card out carefully from the camera. It
may cause a malfunction of the micro SD card or the micro
SD card slot if you use the power too much at lock status.

CAUTION:

• If you install the micro SD card on the camera and remove
with the micro SD card condition indicator lights on, you
must unmount the micro SD card by using the [System >
Storage > Device Management > Unmount] menu. The
micro SD card data is compromised or the camera may
not operate normally, if you remove the card without use
[Unmount] function.

• LG Electronics is not responsible for deleted data caused
by user mishandling when you insert or remove the micro
SD card.

Recommended the micro SD card specification

Maker Capacity Block Size (FAT 32)

LG

Transcend

NOTE:

Speed of reading and writing more than 10 MB/Sec. (Class 6)

Less than

32 GB

32 kbyteSandisk

Mounting the camera

Follow the instructions below to surface mount the camera with
supplied camera mounting bracket.

1. Use the installation guide template to check the mounting
location. Face the front of the label toward the area of
interest. Using the template as a guide, make a hole
through the ceiling.

2. Install the camera mounting bracket to the ceiling.

3. Connect the cables to the cable jacks of the camera body.

NOTE:

Push the cap from inside to arrange the cables through the
conduit. (Optional)

4. Assemble the camera and the housing. Make sure when
you assemble the camera in the right direction. Lock the
camera mounting bracket by tighten the fixing screw.

Fixing Screw

NOTE:

• Adjust the position of [ALIGN] arrow, to the hole at the
bottom of camera.
Then push and turn in the direction of the [LOCK] arrow.

• Arrange the cables by cable tie after installation.

Camera Adjustment

Adjust the rotation position of the camera.

ROTATION

NOTE:

• When you assemble the dome cover, make sure the SD
card PCB position is aligned with the LG logo.

• The camera could be damaged by adjusting Pan, Tilt by
force.

• PAN: 350° / TILT: 75° / ROTATION: 355°

• When you adjust PAN/TILT/ROTATION manually,

be careful your hand is not to hurt by protrusions of other
part.