LG LNU7210R Series Owner's Manual

Warning: This is a class A product. In a

domestic environment this product may cause
radio interference in which case the user may
be required to take adequate measures.
Warning: To reduce a risk of fire or electric
shock, do not expose this product to rain or
moisture.
Warning: Please adopt the power adapter
which can meet the safety extra low voltage
(SELV) standard. And source with DC 12 V or
AC 24 V (depending on models) according
to the IEC60950-1 and Limited Power Source
standard.
Warning: Install the camera on a ceiling or wall
where can withstand the weight of 5 times of
the camera including mounting bracket.
Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.
Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.
Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be placed
on the apparatus.
Caution: Make sure the power supply voltage
is correct before using the camera.
Caution: Do not drop the camera or subject it
to physical shock.
Caution: The sensor may be burned out by
a laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.
Caution: While shipping, the camera should be
packed in its original packing.

Note:

Please make sure the product is installed
appropriate places where secured from flood,
such as under the eaves, to operate properly.
This product is certified as IP66 standard.
However, if there is any flood concerns, it
is highly recommended to use an outdoor
Housing. When you install the camera inside
an outdoor Housing, please use one of the
following methods:

1. Remove the front glass of Housing before
installing the camera.

2. To keep the front glass of Housing, remove
the front cover, and then put the camera
close to the front glass.

The Power Plug is the disconnecting device.
In case of an emergency, the Power Plug
must remain readily accessible.

LG Electronics hereby declares
that this/these product(s)
is/are in compliance with the
essential requirements and
other relevant provisions of
Directive 2004/108/EC and
2011/65/EU.

Contact office for compliance of this
product:

LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The Netherlands

• Please note that this is NOT a Customer
Service contact point. For Customer
Service Information, see Warranty Card
or contact the dealer that you purchased
this product.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Important Safety
Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.

8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.

9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of
the obsolete outlet.

10. Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.

11. Only use attachments/accessories
specified by the manufacturer.

12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.

13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.

14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.

Handling of the unit

Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail
or to get cause of fire or electric shock.

• Remove dust or dirt on the surface of the
lens with a blower.

• Use a soft and lint-free, dry cloth(such as
glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.

• Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.

• This camera is designed for mounting on
the ceiling or wall. If you install this camera
upside down, it may cause malfunction.

Operating and storage
location

Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.

• Extremely hot or cold places (operating
temperature -10 °C to 50 °C, however, we
recommend that the unit be used within a
temperature range of 0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful

electromagnetic radiation such as radio or
TV transmitters.

• Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.

Specication

Item LNU7210R series

Camera

Image Device 6.4 mm (1/2.8 Type) CMOS

Lens Type 3 mm to 9 mm F1.2 (x3 Zoom)

Day / Night ICR (Auto / Day / Night / External / Schedule)

Minimum
Illumination

Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)

B/W: 0 lx @ IR LED on

WDR Support

IR Distance 30 m

Image
Enhancement

Backlight Compensation, 2D+3D-DNR, De-fog, Exposure
Control, AGC, White Balance, Privacy Masking, Sharpness, EIS,
Pivot, Smart IR

Video /
Audio

Compression H.264, H.264_High, MJPEG

Resolution 1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)

Maximum
Frame Rate

60 fps @ 1920 x 1080

Multi-Streaming Up to 4

ROI (Smart­Codec)

Support (Up to 8)

Video Analytics

Motion detection, Tampering alarm, Face detection, Intrusion
detection, Crossing line, Object counting, Object removal,
Object desertion

Text Overlay Support

Audio
Compression

G.711, G.726

2-way Audio Support

Audio Detection Suppor t

Event

Event Trigger Video analytics, Audio detection, Alarm input

Event
Notication

Relay Out, Email, FTP

Pre Event
Buering

Support

Interface

Analog Out BNC out

Audio In / Out 1 / 1

Alarm In / Out 1 In / 1 Out

SD Slot micro SD (Up to 32 GB)

Network

Ethernet RJ-45 10 / 100 BASE-T

Security Password protection, HTTPS (SSL, TLS), IP ltering, IEEE 802.1X

Open Protocol ONVIF 2.2 Prole S, PSIA 1.1

Protocol

IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP,
QoS, UPnP

IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)

Integrated
Software

LG Ipsolute VMS Suite / Mobile application (iPhone, iPad,
Android)

Connections Up to 20

General

Power Source AC 24 V, DC 12 V, PoE

Maximum
Power
Consumption

10.6 W (AC 24 V), 9.1 W (DC 12 V), 9.6 W (PoE)

Maximum Input
Current

670 mA (AC 24 V), 750 mA (DC 12 V), 200 mA (PoE)

Operation
Temperature /
Humidity

-10 ºC to 50 ºC / 0 % RH to 80 % RH

Protection IK10, IP66

Dimension (W x
H x D)

92.1 mm x 89.8 mm x 338.6 mm

Weight 1.54 kg (with Sunshield 1.7 kg)

Note that design and specication of this unit may change from the manual as quality and
improvement without prior notice.

Components

Camera, CD (Software and Owner’s Manual), Installation Manual, Test monitor cable, Wrench, Screws
(3 EA), Installation sticker, Sunshield and Fixing screw

MODEL
LNU7210R series

Please read this manual carefully before operating
your set and retain it for future reference.

OWNER’S MANUAL

High
Denition
Network
Camera

Part Names and Functions

i j mk n

a b c

d e f g h

l

a Lens Cover
b Angle adjuster

Adjust the camera angle.
c Tilt adjuster
Adjust the tilt position.
d Pan adjuster
Adjust the pan position.
e Power input terminal
Connects to DC 12 V or AC 24 V power supply using proper cables. This camera must always

be operated DC 12 V or AC 24 V. Certified/Listed Adaptor which comply with LPS.

f AUDIO IN / OUT (Line Level Input / Output)
g ALARM IN & OUT / ALARM IN & OUT RETURN

Provides physical interface for sensor and Alarm/Relay.
h ETHERNET / PoE Port
Connects to a PC or a network via a hub with a 10 BASE-T / 100 BASE-TX cable attached RJ-45

connector.

NOTE:

Power over Ethernet (PoE) is a technology that integrates power into a standard LAN

infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates the need for
power outlets at the device locations and enables easier application of uninterruptible power
supplies (LPS).

i IR LED

NOTE:

Do not stare at operating IR LED within hazard distances (1 m).

j IR Sensor
k RESET button

Push the button more than 3 seconds, this would restore the factory default network related
settings.

l Video Out Connector

Use this jack for checking the picture with portable monitor when install the camera.

m Jog button
Use this button for control the Zoom / Focus of the camera.
n micro SD card slot

Insert the micro SD card.

Installation

Using the micro SD card

You can record your surveillance environment with
the micro SD card even if the network is disconnected
condition.

To insert the micro SD card

1. Open the Cover on the main body by loosening
the screw.

2. Insert the micro SD card carefully as shown in the
following illustrations. Make sure the micro SD
card terminal position before insert the micro SD
card. Push the back end of the micro SD card to
fix it at the last step.

NOTES:

• Do not use the power too much when you insert
the micro SD card. The micro SD card may be
damaged.

• If you insert the micro SD card in the wrong
position, the micro SD card may be damaged
or it may cause the malfunction of the micro SD
Card Slot.

• Keep the terminal part of the micro SD card in
clean. Be careful the terminal part of the micro SD
card not to dusty.

• As the micro SD card is consumable, the micro
SD card end its days and may be not able to save
data if you use it more than over certain times.
In this case, replace micro SD card to buy a new
one.

• Close the cover and fasten the screw securely
using a screwdriver as shown below.

Remove the micro SD card

1. Press the back end of the micro SD card to
release the lock condition.

2. Take the micro SD card out carefully from the
camera. It may cause a malfunction of the micro
SD card or the micro SD card slot if you use the
power too much at lock status.

CAUTION:

• If you install the micro SD card on the camera
and remove with the micro SD card condition
indicator lights on, you must unmount the micro
SD card by using the [System > Storage > Device
Management > Unmount] menu. The micro SD
card data is compromised or the camera may not
operate normally, if you remove the card without
use [Unmount] function.

• LG Electronics is not responsible for deleted data
caused by user mishandling when you insert or
remove the micro SD card.

Recommended the micro SD card specication

Maker Capacity

Block Size

(FAT 32)

LG

Less than

32 GB

32 kbyteSandisk

Transcend

NOTE:

Speed of reading and writing more than 10 MB/Sec.
(Class 6)

Follow the instructions below to ceiling or wall mount
the camera.

Mounting the Camera

1. Using a template as a guide, make a hole through
the ceiling.

2. Connect the cables to the cable jacks of the
camera body.

3. Install the camera by using M4 Tapping screws to
fix it on the ceiling.

Connecting Waterproof processing
of cable

Surely use the Butyl tape.

1. Connect the cables.

2. Bind the cables together with Butyl tape.

WARNING:

• The cables are not waterproofed completely. So
seal the tube ends and the portions between
cable cores as well as connecting portions with
Butyl tape.

• If not using the Butyl tape, it may cause water
absorption from a gap and finally condensation
and water leakage.

Adjust the camera position

You should adjust the camera angle position as shown
below illustration. Adjust the camera angle position by
following step a and b.

1. Adjust the Pan.

2. Adjust the Tilt.

3. Adjust the Angle.

NOTE:

• The camera could be damaged by adjusting Pan,
Tilt by force.

• Camera can be damaged if you adjust the Pan
/ Tilt / Angle when the screw is fixed.

• Be careful not to rotate the Pan and Angle more
than 360°, it may damage the internal cable.

Assemble the Sunshield

Adjust the position of the Sunshield, then assemble
the Sunshield.

Connection

Precautions

• Be sure to switch off the unit before
installation and connection.

• The installation should be made by
qualified service personnel or system
installers.

• Do not expose the power and connection
cables to moisture, which may cause
damage to the unit.

Connecting Network

You can control and monitor the system via
network. With the remote control (monitoring),
you can change the system configuration
or monitor the image via network. After the
installation, check the network settings for the
remote control and monitoring work.
Connect the IP camera to your network using a
standard RJ-45 network cable as shown below.

ETHERNET
With PoE

PoE Device

(IEEE802.3af)

Broadband

Service

Broadband

Service

Router

Connecting Power Source

Connect power, using one of the methods
listed below:

To use the power adapter

Connect DC 12 V or AC 24 V power source to
the power input terminal as shown below.
(recommended power adapter is DC 12 V or
AC 24 V / 1.5 A or above)

To use the PoE (Power over Ethernet) device

Connect the PoE cable to the LAN port on the
unit. You must use the “IEEE802.3af” standard
PoE device.

ETHERNET
With PoE

PoE Device

(IEEE802.3af)

NOTE:

If the camera doesn’t work properly after
connecting PoE device, please check if the PoE
device supplies enough power.

Connecting Alarm Device

Alarm terminals are used to connect the alarm
(relay) devices such as sensors, door switches,
etc.

ALARM IN & OUT / ALARM IN & OUT RE­TURN (Sensor Input/ Relay Output)

Connect the sensor device and alarm (relay)
device to the alarm terminal. Alarm signal is
outputted at an event occurrence.

Sensor Device

Alarm (relay)

Device

NOTE:

The Photo MOS Relay is rated for 100 mA at
DC 20 V or 100 mA at AC 28 V.

Connecting Microphone and
Speaker Device

Optionally connect an active speaker and/or
external microphone with a built-in amplifier.

AUDIO IN

AUDIO OUT

NOTE:

• When the connecting Network, Power
and Alarm, tighten the screws as shown
above.

• Keep the microphone away from the
speaker to avoid howling.

Connecting Portable Monitor

Connect the portable monitor to the video
jack using the test monitor cable.