LG LND7210R User guide

OWNER’S MANUAL

High

Definition

Network

Camera

Please read this manual carefully before operating your set and retain it for future reference.

MODEL
LND7210 series	LND7210R series

*MFL69458109*

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

•A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

•Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit. Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Specification

		Item	LND7210R series	LND7210 series
		Image Device	6.4 mm (1/2.8 Type) CMOS
		Lens Type	3 mm to 9 mm F1.2 (x3 Zoom)
		Day / Night	ICR (Auto / Day / Night / External / Schedule)
		Minimum	Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)
				B/W: 0.003 lx @ F1.2
		Illumination	B/W: 0 lx @ IR LED on
				(1/30 sec, 50 IRE)
	Camera
		WDR	Support
		IR Distance	20 m
		(LND7210R only)
		Image	Backlight Compensation, 2D+3D-DNR, De-fog, Exposure Control,
			AGC, White Balance, Privacy Masking, Sharpness, EIS, Pivot,
		Enhancement
			SmartIR (LND7210R only)
		Compression	H.264, H.264_High, MJPEG
		Resolution	1920 x 1080 / 1280 x 720 / D1 (704 x 576) / CIF (352 x 240)
		Maximum Frame	60 fps @ 1920 x 1080
		Rate
		Multi-Streaming	Up to 4
		ROI (Region of	Smart codec (Up to 8)
		Interest)
	Video /
			Motion detection, Tampering alarm, Face detection, Intrusion
	Audio
		Video Analytics	detection, Crossing line, Object counting, Object removal, Object
			desertion
		Text Overlay	Support
		Audio	G.711, G.726
		Compression
		2-way Audio	Support
		Audio Detection	Support
		Event Trigger	Video analytics, Audio detection, Alarm input
	Event	Event Notification	Relay Out, Email, FTP
		Pre Event	Support
		Buffering

		Analog Out	BNC out
	Interface	Audio In / Out	1 / 1
		Alarm In / Out	1 In / 1 Out
		SD Slot	micro SD (Up to 32 GB)
		Ethernet	RJ-45 10 / 100 BASE-T
		Security	Password protection, HTTPS (SSL, TLS), IP filtering, IEEE 802.1X
		Open Protocol	ONVIF 2.2 Profile S, PSIA 1.1
			IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP,
	Network	Protocol	QoS, UPnP
			IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
		Integrated	LG Ipsolute VMS Suite / Mobile application (iPhone, iPad,
		Software	Android)
		Connections	Up to 20
		Power Source	DC 12 V, PoE
		Maximum Power	8.7 W (DC 12 V), 10.4 W (PoE 48 V)
		Consumption
		Maximum Input	730 mA (DC 12 V), 280 mA (PoE)
		Current
	General	Operation
		Temperature /	-10 ºC to 50 ºC / 0 % RH to 80 % RH
		Humidity
		Dimension	140 mm x 122 mm
		(Ø x H)
		Weight	620 g		613 g

Note that design and specification of this unit may change from the manual as quality and improvement without prior notice.

Components

Camera, CD (Software and Owner’s Manual), Installation Manual, Test monitor cable, Screws (4 EA), Installation sticker, Camera mounting bracket

Warning: Please adopt the power adapter which can meet the safety extra low voltage (SELV) standard. And source with DC 12 V or AC 24 V (depending on models) according to the IEC60950-1 and Limited Power Source standard.

Warning: Install the camera on a ceiling or wall where can withstand the weight of 5 times of the camera including mounting bracket.

Caution: This installation shall be made by a qualified service person and shall conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution: Make sure the power supply voltage is correct before using the camera.

Caution: Do not drop the camera or subject it to physical shock.

Caution: The sensor may be burned out by a laser beam, so when any laser equipment is being used, make sure that the surface of the sensor not be exposed to the laser beam.

Caution: While shipping, the camera should be packed in its original packing.

Caution: It is permitted to use ancillary equipment (e.g. A UPS) to prevent the damage from mains supply voltage reductions.

Disposal of your old appliance

1.This crossed-out wheeled bin symbol indicates that waste electrical and electronic products (WEEE) should be disposed

of separately from the municipal waste stream.

2.Old electrical products can contain hazardous substances so correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. Your old appliance may contain reusable parts that could be used to repair other products, and other valuable materials that can be recycled to conserve limited resources.

3.You can take your appliance either to the shop where you purchased the product, or contact your local government waste office for details of your nearest authorised WEEE collection point. For the most up to date information for your country please see www.lg.com/global/recycling

EuSP Ltd.

Herald Way Pegasus Business Park

Castle Donington, DE74 2TZ United Kingdom

Important Safety

Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautious not to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail or to get cause of fire or electric shock.

•Remove dust or dirt on the surface of the lens with a blower.

•Use a soft and lint-free, dry cloth(such as glass cleaner) to clean the body. If it is very dirty, use a cloth dampened with a small quantity of neutral detergent then wipe dry.

•Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides.

They may damage the surface finish and/ or impair the operation of the camera.

•This camera is designed for mounting on the ceiling or wall. If you install this camera upside down, it may cause malfunction.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations.

•Extremely hot or cold places (operating temperature -10 °C to 50 °C, however, we recommend that the unit be used within a temperature range of 0 °C to 45 °C)

•Damp or dust place

•Places exposed to rain

•Places subject to strong vibration

•Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.

•Do not use the camera in such place where rapid temperature fluctuation by switching an air conditioner on and off.

	Символ «не для пищевой продукции»	Символ Кедендік одақтың 005/2011
	применяется в соответствие с техническим	техникалық регламентіне сәйкес
	регламентом Таможенного союза «О	қолданылады және осы өнімнің қаптамасын
	безопасности упаковки» 005/2011 и указывает	екінші рет пайдалануға арналмағанын және
	на то, что упаковка данного продукта не	жоюға жататынын көрсетеді. Осы өнімнің
	предназначена для повторного использования	қаптамасын азық-түлік өнімдерін сақтау үшін
	и подлежит утилизации. Упаковку данного	пайдалануға тыйым салынады.
	продукта запрещается использовать для
	хранения пищевой продукции.
	Символ «петля Мебиуса» указывает на	Символ қаптаманы жою мүмкіндігін көрсетеді.
	возможность утилизации упаковки. Символ	Символ сандық код және/немесе әріп
	может быть дополнен обозначением материала	белгілері түріндегі қаптама материалының
	упаковки в виде цифрового и/или буквенного	белгісімен толықтырылуы мүмкін.
	обозначения.

Российская Федерация

Импортер ООО “ЛГ Электроникс Рус”

Адрес импортера: 143160 Российская Федерация, Московская область, Рузский район, сельское поселение Дороховское, 86 км. Минского шоссе, д.9

Адрес производителя: ЛГ ЭЛЕКТРОНИКС (ХУЖОУ) ИНК., ЗАВОД ХАТАИ
ЛГ Электроникс (Хужоу) Инк., завод Хатаи
516006, Китай, пров. ГуанДонг, г. Хужоу, Промышленная зона	Сделано в Китае
Жонгкай, Индустриальный парк Хутаи, ХуФенг Донг Уи Роуд, 13.

Part Names and Functions

A Dome Cover

B IR Sensor (LND7210R only)

C IR LED (LND7210R only)

A

NOTE:

Do not stare at operating IR LED within hazard distances (1 m).

D micro SD card slot

Insert the micro SD card.

E Jog button

		Use this button for control the Zoom / Focus of the camera.
		F Video Out Connector
		Use this jack for checking the picture with portable monitor when install the camera.
		G RESET button
		Push the button more than 3 seconds, this would restore the factory default network related
	B	settings.
		H AUDIO IN / OUT (Line Level Input / Output)
	C
		I ALARM IN & OUT / ALARM IN & OUT RETURN

Provides physical interface for sensor and Alarm/Relay.

		H	I	J K	J Power input terminal
	D				Connects to a DC 12 V power supply using proper cables. This camera must always be
	E				operated a DC 12 V. Certified/Listed Adaptor which comply with LPS.
	F				K ETHERNET / PoE Port
	G				Connects to a PC or a network via a hub with a 10 BASE-T / 100 BASE-TX cable attached
					RJ-45 connector.

NOTE:

Power over Ethernet (PoE) is a technology that integrates power into a standard LAN infrastructure. It enables power to be provided to the network device, such as a network camera, using the same cable as that used for network connection. It eliminates the need for power outlets at the device locations and enables easier application of uninterruptible power supplies (LPS).

	L	L Camera mounting bracket
		You can lock the camera mounting bracket by tighten the screws.

Connection

Precautions Connecting Power Source

•Be sure to switch off the unit before installation and connection.

•The installation should be made by qualified service personnel or system installers.

•Do not expose the power and connection cables to moisture, which may cause damage to the unit.

Connecting Network

You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration

or monitor the image via network. After the installation, check the network settings for the remote control and monitoring work.

Connect the IP camera to your network using a standard RJ-45 network cable as shown below.

Connect power, using one of the methods listed below:

To use the power adapter

Connect a DC 12 V power source to the power input terminal as shown below. (recommended power adapter is DC 12 V / 1.5 A or above)

NOTE:

•When the connecting Alarm and Audio, tighten the screws as shown above.

•Put your finger between the power connector and the camera body to pull out the connector.

PoE Device (IEEE802.3af)

Broadband

Service

Router

Broadband

Service

To use the PoE (Power over Ethernet) device

Connect the PoE cable to the LAN port on the unit. You must use the “IEEE802.3af” standard PoE device.

PoE Device (IEEE802.3af )

NOTE:

If the camera doesn’t work properly after connecting PoE device, please check if the PoE device supplies enough power.

Connecting Alarm Device

Alarm terminals are used to connect the alarm (relay) devices such as sensors, door switches, etc.

ALARM IN & OUT / ALARM IN & OUT RETURN (Sensor Input / Relay Output)

Connect the sensor device and alarm (relay) device to the alarm terminal. Alarm signal is outputted at an event occurrence.

Alarm (relay)

Device

Sensor

Device

NOTE:

•The Photo MOS Relay is rated for 100 mA at DC 20 V or 100 mA at AC 28 V.

•Grasp both ends of the 3 or 4 pin connector plug and then sway both side to pull it out.

Connecting Microphone and Speaker Device

Optionally connect an active speaker and/or external microphone with a built-in amplifier.

AUDIO OUT

AUDIO IN

NOTE:

Keep the microphone away from the speaker to avoid howling.

Installation

Using the micro SD card

You can record your surveillance environment with the micro SD card even if the network is disconnected condition.

To insert the micro SD card

1.Remove the Dome Cover.

2.Insert the micro SD card carefully as shown in the following illustrations. Make sure the micro SD card terminal position before insert the micro SD card. Push the back end of the micro SD card to fix it at the last step.

Remove the micro SD card

1.Press the back end of the micro SD card to release the lock condition.

Mounting the camera	3. Connect the cables to the cable jacks of the camera body.
Follow the instructions below to surface mount the camera with
supplied camera mounting bracket.
1. Use the installation guide template to check the mounting
location. Face the front of the label toward the area of
interest. Using the template as a guide, make a hole
through the ceiling.

	4. Assemble the camera and mounting bracket after align the			Camera Adjustment
	front part of the camera and mounting bracket. Connect			Adjust the rotation position of the camera.
	the unit by following step A and B.

NOTE:

•Do not use the power too much when you insert the micro SD card. The micro SD card may be damaged.

•If you insert the micro SD card in the wrong position, the micro SD card may be damaged or it may cause the malfunction of the micro SD Card Slot.

•Keep the terminal part of the micro SD card in clean. Be careful the terminal part of the micro SD card not to dusty.

•As the micro SD card is consumable, the micro SD card end its days and may be not able to save data if you use it more than over certain times. In this case, replace micro SD card to buy a new one.

*MFL69458109*

2. Install the camera mounting bracket to the ceiling.

2.Take the micro SD card out carefully from the camera. It

may cause a malfunction of the micro SD card or the micro SD card slot if you use the power too much at lock status.

CAUTION:

•If you install the micro SD card on the camera and remove with the micro SD card condition indicator lights on, you

must unmount the micro SD card by using the [System > Storage > Device Management > Unmount] menu. The micro SD card data is compromised or the camera may not operate normally, if you remove the card without use [Unmount] function.

•LG Electronics is not responsible for deleted data caused by user mishandling when you insert or remove the micro SD card.

Recommended the micro SD card specification

	Maker	Capacity	Block Size
			(FAT 32)
	LG	Less than
	Sandisk		32 kbyte
		32 GB
	Transcend
	NOTE:

Speed of reading and writing more than 10 MB/Sec. (Class 6)

ROTATION

NOTE:

•Be careful of sharp edge after removing the cap of cable conduit.

•Arrange the cables by cable tie after installation.

NOTE:

•When you assemble the dome cover, make sure the SD card PCB position is aligned with the LG logo.

•The camera could be damaged by adjusting Pan, Tilt by force.

•PAN: 350° / TILT: 75° / ROTATION: 355°

•To disassemble the camera from the mounting bracket, rotate the camera counterclockwise with pressing the PUSH button inside the camera body.