LG LND5220R User Guide

Specication

OWNER’S MANUAL

Network
Camera

Please read this manual carefully before operating
your set and retain it for future reference.

MODEL

LND5220R

Camera

Video /
Audio

Event

Interface

Item LND5220R

Image Device 6.4 mm (1/2.8 Type) CMOS

Lens Type 3 to 9 mm F1.2 (x3 Zoom)

Day / Night ICR (Auto / Day / Night / External / Schedule)

Minimum Illumination

WDR Digital (Automatic Tone Control)

IR Distance 30 m

Image Enhancement

Video Compression H.264, H.264_High, MJPEG

Resolution 1920 x 1080 / 1280 x 720 / D1 (720x576) / CIF (352 x 240)

Maximum Frame Rate 30 fps @ 1920 x 1080

Multi-Streaming Up to 4

ROI (Region of
Interest)

Video Analytics

Text Overlay Support

Event Trigger Video analytics, Alarm input

Event Notication Relay Out, Email, FTP

Pre Event Buering Support

Alarm In / Out 1 In / 1 Out

SD Slot micro SD (Up to 64 GB, FAT 32)

Color: 0.03 lx @ F1.2 (1/30 sec, 50 IRE)

B/W: 0 lx @ IR LED on

Backlight Compensation, HSBLC, 2D+3D-DNR, De-fog,
Exposure Control, AGC, White Balance, Privacy Masking,
Sharpness, Pivot

Smart codec (Up to 8)

Motion detection, Tampering alarm, Intrusion detection,
Crossing line, Object counting, Object removal,
Object desertion

Ethernet RJ-45 10 / 100 BASE-T

Security

Open Protocol ONVIF 2.2 Prole S, PSIA 1.1

Network

General

Note that design and specication of this unit may change from the manual as quality and
improvement without prior notice.

Components

Camera, CD (Software and Owner’s Manual), Installation Manual, Anchor (4 EA),
Tapping Screw (4 EA), Installation sticker, Camera mounting bracket

Protocol

Integrated Software

Connections Up to 20

Power Source DC 12 V, PoE

Maximum Power
Consumption

Maximum Input
Current

Operation
Temperature /
Humidity

Dimension
(Ø x H)

Weight 560 g

Password protection, HTTPS (SSL, TLS), IP ltering, IEEE 802.1X

IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP,
ICMP, QoS, UPnP port forwarding

IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)

LG Ipsolute VMS Suite / Mobile application (iPhone, iPad,
Android)

8.2 W

610 mA (DC 12 V), 170 mA (PoE)

-10 ºC to 55 ºC / 0 % RH to 80 % RH

140 mm x 122 mm

OPEN SOURCE SOFTWARE NOTICE

To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in
this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices
are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the
cost of performing such distribution (such as the cost of media, shipping and handling) upon email
request to [e-mail]. This oer is valid for three (3) years from the date on which you
purchased the product.

*MFL69355803*

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.

Warning: TO PREVENT FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.

Warning: Do not install this equipment in a
confined space such as a bookcase or similar
unit.

Warning: Wiring methods shall be in
accordance with the National Electric Code,
ANSI/NFPA 70.

Warning: This is a class A product. In a
domestic environment this product may cause
radio interference in which case the user may
be required to take adequate measures.

Warning: Please adopt the power adapter
which can meet the safety extra low voltage
(SELV) standard. And source with DC 12 V or
AC 24 V (depending on models) according
to the IEC60950-1 and Limited Power Source
standard.

Warning: Install the camera on a ceiling or
wall where can withstand the weight of 5 times
of the camera including mounting bracket.

Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.

Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.

Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be placed
on the apparatus.

Caution: Make sure the power supply voltage
is correct before using the camera.

Caution: Do not drop the camera or subject it
to physical shock.

Caution: The sensor may be burned out by
a laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.

Caution: While shipping, the camera should
be packed in its original packing.

Caution: Do not use high voltage products
around this product. (ex. Electrical swatter)
This product may malfunction due to electrical
shock.

Notice: For safety marking information
including product identification and supply
ratings, please refer to the main label on the
bottom or the other surface of the product.

Contact oce for compliance of this product:

LG Electronics European Shared Service Center B.V.

European Standard Team

Krijgsman 1

1186 DM Amstelveen

The Netherlands

Disposal of your old appliance

1. This crossed-out
wheeled bin symbol
indicates that waste
electrical and electronic
products (WEEE)
should be disposed
of separately from the
municipal waste stream.

2. Old electrical products can contain
hazardous substances so correct disposal
of your old appliance will help prevent
potential negative consequences for the
environment and human health. Your old
appliance may contain reusable parts that
could be used to repair other products,
and other valuable materials that can be
recycled to conserve limited resources.

3. You can take your appliance either to the
shop where you purchased the product,
or contact your local government waste
office for details of your nearest authorised
WEEE collection point. For the most up to
date information for your country please
see www.lg.com/global/recycling

Handling of the unit

Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail
or to get cause of fire or electric shock.

• Remove dust or dirt on the surface of the
lens with a blower.

• Use a soft and lint-free, dry cloth(such as
glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.

• Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides. They may damage the surface
finish and/or impair the operation of the
camera.

• This camera is designed for mounting on
the ceiling or wall. If you install this camera
upside down, it may cause malfunction.

Operating and storage
location

Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.

• Extremely hot or cold places (operating
temperature -10 °C to 55 °C, however, we
recommend that the unit be used within a
temperature range of 0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful

electromagnetic radiation such as radio or
TV transmitters.

• Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.

Part Names and Functions

Connection

a

b

c

d
e

f

g

a Dome Cover

b IR Sensor

c IR LED

Do not stare at operating IR LED within hazard distances (1 m).

,

h i j

d micro SD card slot

Insert the micro SD card.

e Jog button

Use this button for control the Zoom / Focus of the camera.

(Left : Wide, Right : Tele, Up : Near, Down : Far, Push : Auto Focus)

f RESET button

Push the button more than 3 seconds, this would restore the factory default network related

settings.

g Camera mounting bracket

You can lock the camera mounting bracket by tighten the screws.

To disassemble the camera from the mounting bracket, rotate the camera

,

counterclockwise with pressing the PUSH button inside the camera body.

h ALARM IN & OUT / ALARM IN & OUT RETURN

Provides physical interface for sensor and Alarm/Relay.

i Power input terminal

Connects to a DC 12 V power supply using proper cables. This camera must always be operated

a DC 12 V. Certied/Listed Adaptor which comply with LPS.

j ETHERNET/PoE Port

Connects to a PC or a network via a hub with a 10 BASE-T / 100 BASE-TX cable attached

RJ-45 connector.

Power over Ethernet (PoE) is a technology that integrates power into a standard LAN

,

infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates
the need for power outlets at the device locations and enables easier application of
uninterruptible power supplies (LPS).

Precautions

• Be sure to switch o the unit before

installation and connection.

• The installation should be made by qualied

service personnel or system installers.

• Do not expose the power and connection

cables to moisture, which may cause
damage to the unit.

Connecting Network

You can control and monitor the system via
network. With the remote control (monitoring),
you can change the system conguration
or monitor the image via network. After the
installation, check the network settings for the
remote control and monitoring work.
Connect the IP camera to your network using a
standard RJ-45 network cable as shown below.

PoE Device

(IEEE802.3af )

Broadband

Service

Router

Broadband

Service

Connecting Power Source

Connect power, using one of the methods
listed below:

To use the power adapter

Connect a DC 12 V power source to the power
input terminal as shown below.
(Recommended power adapter is DC 12 V /

1.5 A or above)

2

3

• When the connecting Alarm and

,

Audio, tighten the screws as shown
above.

• To remove the power connector, as
shown below. Grasp both ends of the
power connector and pull out.

To use the PoE (Power over Ethernet) device

Connect the PoE cable to the LAN port on the
unit. You must use the “IEEE802.3af” standard
PoE device.

PoE Device

(IEEE802.3af )

If the camera doesn’t work properly after

,

connecting PoE device, please check if
the PoE device supplies enough power.

Connecting Alarm Device

Alarm terminals are used to connect the alarm
(relay) devices such as sensors, door switches,
etc.

ALARM IN & OUT / ALARM IN & OUT RETURN
(Sensor Input / Relay Output)

Connect the sensor device and alarm (relay)
device to the alarm terminal. Alarm signal is
outputted at an event occurrence.

Sensor
Device

Alarm (relay)

Device

• The Photo MOS Relay is rated for

,

100 mA at DC 20 V or 100 mA at
AC 28 V.

• Grasp both ends of the 3 or 4 pin
connector plug and then sway both
side to pull it out.

Installation

Using the micro SD card

You can record your surveillance environment with the micro SD
card even if the network is disconnected condition.

To insert the micro SD card

1. Remove the Dome Cover.

2. Insert the micro SD card carefully as shown in the following
illustrations. Make sure the micro SD card terminal position
before insert the micro SD card. Push the back end of the
micro SD card to x it at the last step.

• Do not use the power too much when you insert the

,

micro SD card. The micro SD card may be damaged.

• If you insert the micro SD card in the wrong position,
the micro SD card may be damaged or it may cause
the malfunction of the micro SD Card Slot.

• Keep the terminal part of the micro SD card in clean.
Be careful the terminal part of the micro SD card not
to dusty.

• As the micro SD card is consumable, the micro SD
card end its days and may be not able to save data if
you use it more than over certain times. In this case,
replace micro SD card to buy a new one.

Remove the micro SD card

1. Press the back end of the micro SD card to release the lock
condition.

2. Take the micro SD card out carefully from the camera. It may
cause a malfunction of the micro SD card or the micro SD
card slot if you use the power too much at lock status.

• If you install the micro SD card on the camera
and remove with the micro SD card condition
indicator lights on, you must unmount the micro
SD card by using the [System > Storage > Device
Management > Unmount] menu. The micro SD
card data is compromised or the camera may not
operate normally, if you remove the card without use
[Unmount] function.

• LG Electronics is not responsible for deleted data
caused by user mishandling when you insert or
remove the micro SD card.

Recommended the micro SD card specication

Maker Capacity

LG

Transcend

• Speed of reading and writing more than

,

10 MB/Second (Class 6)

• Format the micro SD card before camera turns on.

• In the case of the [DiskID:SDCard] or [Status:Unknown],

you can run the micro SD card by using the format
function. (For example, initial insertion of micro SD
Card over 64 GB)

Less than 64 GB 32 kbyteSandisk

Block Size

(FAT 32)

Mounting the camera

Follow the instructions below to surface mount the camera with
supplied camera mounting bracket.

1. Use the installation guide template to check the mounting
location. Face the front of the label toward the area of
interest. Using the template as a guide, make a hole
through the ceiling.

2. Disassemble the camera from the mounting bracket.
Install the camera mounting bracket to the ceiling.

3. Connect the cables to the cable jacks of the camera body. 4. Assemble the camera and mounting bracket after align the
front part of the camera and mounting bracket. Connect
the unit by following step a and b.

• Be careful of sharp edge after removing the cap of

,

cable conduit.

• Arrange the cables by cable tie after installation.

Camera Adjustment

Adjust the Pan / Tilt / Rotation position of the camera.

TILT

PAN

• Manual adjustment:

,

PAN: 360° / TILT: 75° / ROTATION: 355°

• When you adjust PAN / TILT / ROTATION manually,
be careful your hand is not to hurt by protrusions of
other part.

• The camera could be damaged by adjusting Pan, Tilt
by force.

ROTATION