LG LND5110 User Guide

OWNER’S MANUAL

High

Definition

Network

Camera

Please read this manual carefully before operating your set and retain it for future reference.

MODEL

LND5110 series

Specification

			Item	LND5110 series
			Image Device	6.28 mm (1/3 Type) CMOS
			Lens Type	3 mm to 9 mm F1.2
			Day/Night	ICR (Auto / Day / Night / External / Schedule)
			Minimum Illumination	Color: 0.03 lx (F1.2, Gain : High, 1/30 sec)
		Camera		B/W: 0.002 lx (F1.2, Gain : High, 1/30 sec)
			WDR	Support
				Backlight Compensation, 2D+3D-DNR, De-fog,
			Image Enhancement	Exposure Control, AGC, White Balance, Privacy Masking,
				Sharpness, EIS, Pivot
			Compression	H.264, H.264_High, MJPEG
			Resolution	1280 x 1024 / 1280 x 720 / D1 (704 x 576) /
				CIF (352 x 240)
			Maximum Frame Rate	60 fps @ 1280 x 1024
			Multi-Streaming	Up to 4
		Video /	ROI (Region of Interest)	Smart codec (Up to 8)
				Motion detection, Tampering alarm, Face detection,
		Audio
			Video Analytics	Intrusion detection, Crossing line, Object counting,
				Object removal, Object desertion
			Text Overlay	Support
			Audio Compression	G.711, G.726
			2-way Audio	Support
			Audio Detection	Support
			Event Trigger	Video analytics, Audio detection, Alarm input
		Event	Event Notification	Relay Out, Email, FTP
			Pre Event Buffering	Support
			Analog Out	BNC Out
		Interface	Audio In/Out	1 / 1
			Alarm In/Out	1 In / 1 Out
			SD Slot	micro SD (Up to 32 GB)

		Ethernet	RJ-45 10/100BASE-T
		Security	Password protection, HTTPS (SSL, TLS), IP filtering,
			IEEE 802.1X
		Open Protocol	ONVIF 2.2 Profile S, PSIA 1.1
	Network		IPv4 and IPv6 : TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP,
		Protocol	DHCP, ICMP, QoS, UPnP
			IPv4 : FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)
		Integrated Software	LG Ipsolute VMS Suite / Mobile application (iPhone,
			iPad, Android)
		Connections	Up to 20
		Power Source	DC 12 V, PoE
		Maximum Power	5.9 W
		Consumption
	General	Maximum Input Current	490 mA (DC 12 V), 130 mA (PoE)
		Operation Temperature/	-10 ºC to 55 ºC / 0 % RH to 80 % RH
		Humidity
		Dimension (Ø x H)	140 mm x 122 mm
		Weight	530 g

Note that design and specification of this unit may change from the manual as quality and improvement without prior notice.

Components

Camera, CD (Software and Owner’s Manual), Installation Manual, Test monitor cable, Screws (4 EA), Installation sticker, Camera mounting bracket

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

•A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

•Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

•Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Warning: Please adopt the power adapter which can meet the safety extra low voltage (SELV) standard. And source with DC 12 V or AC 24 V (depending on models) according to the IEC60950-1 and Limited Power Source standard.

Warning: Install the camera on a ceiling or wall where can withstand the weight of 5 times of the camera including mounting bracket.

Caution: This installation shall be made by a qualified service person and shall conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution: Make sure the power supply voltage is correct before using the camera.

Caution: Do not drop the camera or subject it to physical shock.

Caution: The sensor may be burned out by a laser beam, so when any laser equipment is being used, make sure that the surface of the sensor not be exposed to the laser beam.

Caution: While shipping, the camera should be packed in its original packing.

To disconnect power from mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

LG Electronics hereby declares that this/these product(s) is/ are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC and 2011/65/EU.

Contact office for compliance of this product:

LG Electronics Inc.

EU Representative, Krijgsman 1,1186 DM Amstelveen, The Netherlands

•Please note that this is NOT a Customer Service contact point. For Customer Service Information, see Warranty Card or contact the dealer that you purchased this product.

Important Safety

Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautious not to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail or to get cause of fire or electric shock.

•Remove dust or dirt on the surface of the lens with a blower.

•Use a soft and lint-free, dry cloth(such as glass cleaner) to clean the body. If it is very dirty, use a cloth dampened with a small quantity of neutral detergent then wipe dry.

•Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides.

They may damage the surface finish and/ or impair the operation of the camera.

•This camera is designed for mounting on the ceiling or wall. If you install this camera upside down, it may cause malfunction.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations.

•Extremely hot or cold places (operating temperature -10 °C to 55 °C, however, we recommend that the unit be used within a temperature range of 0 °C to 45 °C)

•Damp or dust place

•Places exposed to rain

•Places subject to strong vibration

•Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.

•Do not use the camera in such place where rapid temperature fluctuation by switching an air conditioner on and off.

Part Names and Functions

				A Dome Cover
				B micro SD card slot
					Insert the micro SD card.
				C Jog button
					Use this button for control the Zoom / Focus of the camera.
A					(Left : Wide, Right : Tele, Up : Near, Down : Far, Push : Auto Focus)
				D	Video Out Connector

Use this jack for checking the picture with portable monitor when install the camera.

E RESET button

Push the button more than 3 seconds, this would restore the factory default network related settings.

F Camera mounting bracket

You can lock the camera mounting bracket by tighten the screws.

, To disassemble the camera from the mounting bracket, rotate the camera counterclockwise with pressing the PUSH button inside the camera body.

B
C		G AUDIO IN / OUT (Line Level Input / Output)
D		H ALARM IN & OUT / ALARM IN & OUT RETURN
E		Provides physical interface for sensor and Alarm/Relay.
		I Power input terminal
		Connects to a DC 12 V power supply using proper cables. This camera must always be operated
		a DC 12 V. Certified/Listed Adaptor which comply with LPS.
		J ETHERNET/PoE Port
F		Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached
		RJ-45 connector.
		, Power over Ethernet (PoE) is a technology that integrates power into a standard LAN
G	H I J	infrastructure. It enables power to be provided to the network device, such as a network
		camera, using the same cable as that used for network connection. It eliminates
		the need for power outlets at the device locations and enables easier application of
		uninterruptible power supplies (LPS).

Connection

Precautions

•Be sure to switch off the unit before installation and connection.

•The installation should be made by qualified service personnel or system installers.

•Do not expose the power and connection cables to moisture, which may cause damage to the unit.

Connecting Network

You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration

or monitor the image via network. After the installation, check the network settings for the remote control and monitoring work.

Connect the IP camera to your network using a standard RJ-45 network cable as shown below.

PoE Device (IEEE802.3af )

Broadband

Service

Router

Broadband

Service

Connecting Power Source

Connect power, using one of the methods listed below:

To use the power adapter

Connect a DC 12 V power source to the power input terminal as shown below. (Recommended power adapter is DC 12 V/ 1.5 A or above)

,• When the connecting Alarm and Audio, tighten the screws as shown above.

•Put your finger between the power connector and the camera body to pull out the connector.

To use the PoE (Power over Ethernet) device

Connect the PoE cable to the LAN port on the unit. You must use the “IEEE802.3af” standard PoE device.

PoE Device (IEEE802.3af )

,If the camera doesn’t work properly after connecting PoE device, please check if the PoE device supplies enough power.

Connecting Alarm Device

Alarm terminals are used to connect the alarm (relay) devices such as sensors, door switches, etc.

ALARM IN & OUT / ALARM IN & OUT RETURN (Sensor Input / Relay Output)

Connect the sensor device and alarm (relay) device to the alarm terminal. Alarm signal is outputted at an event occurrence.

Sensor			Alarm (relay)
Device			Device

,• The Photo MOS Relay is rated for 100 mA at DC 20 V or 100 mA at AC 28 V.

•Grasp both ends of the 3 or 4 pin connector plug and then sway both side to pull it out.

Connecting Microphone and Speaker Device

Optionally connect an active speaker and/or external microphone with a built-in amplifier.

Audio IN	Audio OUT

,Keep the microphone away from the speaker to avoid howling.

Installation

Using the micro SD card

You can record your surveillance environment with the micro SD card even if the network is disconnected condition.

To insert the micro SD card

1.Remove the Dome Cover.

2.Insert the micro SD card carefully as shown in the following illustrations. Make sure the micro SD card terminal position before insert the micro SD card. Push the back end of the micro SD card to fix it at the last step.

Remove the micro SD card

1.Press the back end of the micro SD card to release the lock condition.

2.Take the micro SD card out carefully from the camera. It may cause a malfunction of the micro SD card or the micro SD card slot if you use the power too much at lock status.

Mounting the camera

3. Connect the cables to the cable jacks of the camera body.

Follow the instructions below to surface mount the camera with supplied camera mounting bracket.

1.Use the installation guide template to check the mounting location. Face the front of the label toward the area of interest. Using the template as a guide, make a hole through the ceiling.

4.Assemble the camera and mounting bracket after align the front part of the camera and mounting bracket. Connect the unit by following step Aand B.

,• Do not use the power too much when you insert the micro SD card. The micro SD card may be damaged.

•If you insert the micro SD card in the wrong position, the micro SD card may be damaged or it may cause the malfunction of the micro SD Card Slot.

•Keep the terminal part of the micro SD card in clean. Be careful the terminal part of the micro SD card not to dusty.

•As the micro SD card is consumable, the micro SD card end its days and may be not able to save data if you use it more than over certain times. In this case, replace micro SD card to buy a new one.

. • If you install the micro SD card on the camera and remove with the micro SD card condition indicator lights on, you must unmount the micro SD card by using the [System > Storage > Device Management > Unmount] menu. The micro SD card data is compromised or the camera may not

operate normally, if you remove the card without use [Unmount] function.

•LG Electronics is not responsible for deleted data caused by user mishandling when you insert or remove the micro SD card.

Recommended the micro SD card specification

	Maker	Capacity	Block Size
			(FAT 32)
	LG
	Sandisk	Less than 32 GB	32 kbyte

Transcend

, Speed(Class 6)of reading and writing more than 10 MB/Sec.

2.Disassemble the camera from the mounting bracket. Install the camera mounting bracket to the ceiling.

,• Be careful of sharp edge after removing the cap of cable conduit.

•Arrange the cables by cable tie after installation.

Camera Adjustment

1.Connect the portable monitor to the video jack using the test monitor cable.

2.Adjust the Pan/Tilt/Rotation position of the camera.

TILT

ROTATION

PAN

,• When you assemble the dome cover, make sure the SD card PCB position is aligned with the LG logo.

•Manual adjustment:

PAN: 360° / TILT: 75° / ROTATION: 355°

•When you adjust PAN/TILT/ROTATION manually,

be careful your hand is not to hurt by protrusions of other part.