LG LAS950M User Manual

SMART Hi-Fi AUDIO

Wireless Multi-room Sound Bar

Model : LAS950M

ENGLISH | OWNER’S MANUAL

Please read this manual carefully before
operating your speaker and retain it for future
reference.

Getting Started 3

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK DO NOT REMOVE COVER (OR BACK) NO

USER-SERVICEABLE PARTS INSIDE REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

This lightning ash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the

sucient magnitude to constitute a risk of electric
shock to persons.

accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.

WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.

CAUTION: Do not use high voltage products
around this product. (ex. Electrical swatter) This
product may malfunction due to electrical shock.

CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, shall be placed on the
apparatus.

CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a built­in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.

product’s enclosure that may be of

The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature

NOTICE: For safety marking information including
product identication and supply ratings, please
refer to the main label on the bottom or rear of the
apparatus.

For models using an adapter

Only use the AC adapter supplied with this device.
Do not use a power supply from another device or
another manufacturer. Using any other power cable
or power supply may cause damage to the device
and void your warranty.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon
a dedicated circuit;

That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specication page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or re. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. The
Power Plug is the disconnecting device. In case of
an emergency, the Power Plug must remain readily
accessible.

1

Getting Started

Getting Started4

This device is equipped with a portable battery or
accumulator.

Safety way to remove the battery from the
equipment: Remove the old battery or battery

1

pack, follow the steps in reverse order than

Getting Started

the assembly. To prevent contamination of the
environment and bring on possible threat to
human and animal health, the old battery or
the battery put it in the appropriate container
at designated collection points. Do not dispose
of batteries or battery together with other
waste. It is recommended that you use local,
free reimbursement systems batteries and
accumulators. The battery should not be exposed
to excessive heat such as sunshine, re or the like.

FCC Compliance Statement

This device complies with part 15 of the FCC
rules. Operation is subject to the following two
conditions:

(1) This device may not cause harmful interference,
and

(2) This device must accept any interference

received, including interference that may cause
undesired operation.

NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:

yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment

and receiver.

yConnect the equipment into an outlet on a

circuit dierent from that to which the receiver is
connected.

yConsult the dealer or an experienced radio/TV

technician for help.

CAUTION: Any changes or modications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.

FCC WARNING: This equipment may generate
or use radio frequency energy. Changes or
modications to this equipment may cause harmful
interference unless the modications are expressly
approved in the instruction manual. The user could
lose the authority to operate this equipment if an
unauthorized change or modication is made.

FCC RF Radiation Exposure Statement : This
equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
This equipment should be installed and operated
with minimum distance 20 cm between the
radiator and your body. End users must follow the
specic operating instructions for satisfying RF
exposure compliance. This transmitter must not be
co-located or operating in conjunction with any
other antenna or transmitter.

FCC Radio Frequency Interference
Requirements

This device is restricted to indoor use due to its
operation in the 5.15 to 5.25 GHz frequency range.
FCC requires this product to be used indoors for
the frequency range 5.15 to 5.25 GHz to reduce the
potential for harmful interference to co-channel
Mobile Satellite systems. High power radars are
allocated as primary users of the 5.25 to 5.35 GHz
and 5.65 to 5.85 GHz bands. These radar stations
can cause interference with and/or damage this
device. This device cannot be co-located with any
other transmitter.

CAUTION: Regulations of the FCC and FAA prohibit
airborne operation of radio-frequency wireless
devices because their signals could interfere with
critical aircraft instruments.

Responsible Party :

LG Electronics USA, Inc.1000 Sylvan Avenue
Englewood Clis, NJ 07632
TEL. : [phone]

IMPORTANT SAFETY
INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.

8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.

9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.

10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

11. Only use attachments/accessories specified by
the manufacturer.

12. Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination
to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms
or when unused for long periods of time.

14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power­supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.

Getting Started 5

1

Getting Started

Table of Contents6

Table of Contents

1 Getting Started

3 Safety Information
8 Main Features
8 Introduction
9 Accessories
10 Front panel
10 Rear panel
11 Remote control
12 Installing the sound bar
12 – Installing the cover foot
12 Mounting the main unit on a wall

2 Connecting

14 Wireless subwoofer connection
15 Connection overview
15 Connecting to your TV
15 – Using an OPTICAL cable
16 – LG Sound Sync
17 – Using an HDMI cable
17 – Enjoy rich sound broadcast of the

channel with the sound bar
18 – What is SIMPLINK?
18 – ARC (Audio Return Channel) function
19 – Additional information for HDMI
19 Optional equipment connection
19 – HDMI connection
20 – PORT. (Portable) IN connection
21 – OPTICAL IN connection
21 – Connecting IR Blaster
22 Understanding Network Connection
22 – Basic Connection
22 – Group playback using Music Flow

Player app
23 Installing “Music Flow Player” App
24 – Starting with Music Flow Player app
25 Connecting the speaker to your Home

Network

25 – Connecting the speaker to your

network with a LAN cable

27 – Connecting the speaker to your

Network via the Wi-Fi Setup Method
(Android)

30 – Connecting the speaker to your

Network via the Wi-Fi Setup Method
(iOS)

34 Connecting the speakers to your Home

Network (Additional)

34 – Adding another speaker

3 Operating

37 Enjoying the Music with Music Flow Player

app
37 – Overview of Home menu
38 – Overview of the side menu
38 – Playing a song
40 – Overview of Playback
41 Different ways of listening to music
42 – Group Playback
43 – Surround playback
44 – Seamless playback
45 Using LG HomeChat
45 – About LG HomeChat
45 – How to start LG HomeChat
47 – Usage Examples
48 – Overview of setting menu
49 – [General] Menu
49 – [Speakers] Menu
50 – [Alarms/Sleep Timer] Menu
50 – [Music Library] Menu
50 – [Account management] Menu
51 – [Advance Settings] Menu
52 – [Account management] Menu
52 – [Update] Menu
52 – [Open source licenses] Menu
53 Using a Bluetooth Wireless Technology
53 – About Bluetooth
53 – Bluetooth profiles
53 – Listening to Music of a Bluetooth

Device
54 Other operations
54 – DRC (Dynamic Range Control)
54 – AV Sync
54 – Turn off the sound temporarily

55 – Displaying input source information
55 – Sleep timer setting
55 – Using your TV remote control
55 – Adjust the Treble/Bass/Sub-woofer
55 – Night mode
56 – AUTO POWER On/Off
56 Sound adjustment
56 – Adjust volume level automatically
56 Using Media Server for PC
56 – Music Flow PC Software for windows
57 – Nero MediaHome 4 Essentials for

Mac OS
58 Standby mode
58 – Standby mode
58 – Network standby mode
59 Reset the Speaker
59 – Resetting the speaker

Table of Contents 7

1

2

3

4 Troubleshooting

60 Troubleshooting
60 – General
61 – Network
62 – Application and PC Software

5 Appendix

63 File requirement
63 Trademarks and licenses
64 Specifications
66 Handling the Speaker
66 Important Information Relating to

Network Services

67 TERMS OF USE

Some of the content in this manual may dier from Music Flow Player app depending on the
application’s version.

4

5

Getting Started8

Main Features

Made for iPod/iPhone/iPad or

1

Android device

Getting Started

Enjoys music from iPod/iPhone/iPad or Android
device with simple connection.

LG Sound Sync

Controls volume level of this unit by the remote
control of your LG TV that is compatible with LG
Sound Sync.

Portable In

Listens to music from your portable device.

Music Flow Player application

Listens to music stored on your smart device.

You can control this speaker with your iPod touch/
iPhone/iPad or Android device via Music Flow
Player app. This speaker and your smart device
must be connected to the same network. Visit
“iTunes store” or “Google Play Store” or use the QR
code shown below to search for “Music Flow Player”
app. For detailed information, refer to page 23.

Introduction

Symbol used in this manual

Note

,

Indicates special notes and operating features.

Caution

>

Indicates cautions for preventing possible damages
from abuse.

(Android OS)

yDepending on the application’s version and the

settings of smart device, Music Flow Player app
may not be operated normally.

ySome smart devices may not be compatible with

this speaker.

(Apple iOS)

Accessories

Please check and identify the supplied accessories.

Designs and specications of the accessories are
subject to change without prior notice.

Remote control (1) Batteries (2)

Getting Started 9

1

Getting Started

Wall bracket (2) Wall bracket install

Screws (2) Cable ties for arranging

Foot IR Blaster

Optical

guide (1)

cables (2)

Getting Started10

Front panel

1

Getting Started

Display window

A

Remote sensor

B

LED indicator

C

Shows connection status.

(Standby/On)

D 1/!

- Power On

- Switching to the standby mode (page 58)

F (Function)

E

Selects the function and input source.

Rear panel

IN 1

F p/o

G

H

(Volume)

Adjusts volume level.

(Wi-Fi)

Connects your speaker to your network.
(page 27)

(Add)

Adds the speaker to your network. (page 34)

IN 2 IN 3IR BLASTER

S/W download connector (For service only)

A

ETHERNET : LAN port

B

OPT. IN 2/OPT. IN 1 : Optical input

C

HDMI IN 1/HDMI OUT

D

output

(TV ARC)

: HDMI input /

PORTABLE IN : Portable input

E

HDMI IN 2/HDMI IN 3 : HDMI input

F

IR BLASTER

G

AC power cord

H

Getting Started 11

Remote control

Battery Installation

Remove the battery cover on the rear of the
Remote Control, and insert two R03 (size AAA)
batteries with and matched correctly.

• • • • • • • • • • a • • • • • • • • •

(Power) : Switches the unit ON or OFF. / Switches

1

to the standby mode.

FUNC : Selects the function and the input source.

(Mute) : Mutes the sound.

OPTICAL : Changes input source to OPTICAL
directly.

: Adjusts sound level of Treble, Bass and Sub-

woofer.

VOL o/p : Adjusts speaker volume.

• • • • • • • • • • b • • • • • • • • •

REPEAT : Listen to your music repeatedl-y.

C/V

- Skips Fast backward or Forward.

dM

playback.

INFO : Displays the input source information.

• • • • • • • • • • c • • • • • • • • •

DRC : Turns on or o DRC function.

intensity and improve neness and softness.

AUTO VOL : Turns on or o the AUTO VOLUME
mode.

AV SYNC : Synchronizes the audio and video.

SLEEP : Sets the system to turn o automatically at

a specied time.

AUTO POWER : Turns on or o AUTO POWER
function. (Refer to the page 56.)

(Skip) :

(Play/Pause) : Starts playback. / Pauses

Note

,

You can use these playback buttons after
play music by “Music Flow Player” App or PC
software.

: Set Night mode to On to reduce the sound

1

Getting Started

Getting Started12

Installing the sound bar

1

You can hear the sound by connecting the unit to

Getting Started

the other device : TV, Blu-ray disc player, DVD player,
etc.

Place the unit in front of the TV and connect it to
the device you want. (Refer to pp. 15 - 21)

You can place the wireless subwoofer anywhere in
your room. But it is better to place the subwoofer
near the main unit. Turn it slightly toward the center
of the room to reduce the wall reections.

Caution

>

yFor best performance of wireless connection

such as Bluetooth or wireless subwoofer,
do not install the unit on Metallic furniture
because wireless connection communicates
through a module positioned on the
bottom of the unit.

yBe careful not to make scratches on the

surface of the Unit /Sub-Woofer when
installing or moving them.

Installing the cover foot

You can extend the height of the unit by using
cover foot (height : 11 mm)

Mounting the main unit on a wall

You can mount the main unit on a wall.

Caution

>

Because it is dicult to make a connection
after installing this unit, you should connect
the cables before installation.

Preparation materials

Unit

Wall bracket install guide

Wall bracket

Screws

(Not supplied)

Screws (A)

Wall plug

1. Turn the unit upside down.

2. Peel off a sticker attached to the cover foot.
Then place it on the existing foot of the unit.

3. Press the cover foot with adequate force to get
it rmly xed.

Getting Started 13

1. Match the TV’s BOTTOM EDGE of Wall bracket
install guide with the bottom of TV and attach
to the position.

TV

2. When you mount it on a wall (concrete), use the
wall plugs. You should drill some holes. A guide
sheet (Wall bracket install guide) is supplied to
drill. Use the sheet to check the point to drill.

3. Remove the Wall bracket install guide.

4. Fix the brackets with screws (A) as shown in the
illustration below.

5. Put the unit on the brackets to match screw
holes on the bottom of the unit.

6. Fix the unit with the screws firmly.

Note

,

To detach the unit, perform it in reverse order.

Caution

>

yDo not install this unit upside down. It can

damage the parts of this unit or be the
cause of personal injury.

yDo not hang onto the installed unit and

avoid any impact to the unit.

ySecure the unit rmly to the wall so that it

does not fall o. If the unit falls o, it may
result in an injury or damage to the product.

yWhen the unit is installed on a wall, please

make sure that a child does not pull any of
connecting cables, as it may cause it to fall.

1

Getting Started

Note

,

Screws (A) and Wall Plugs are not supplied for
mounting the unit. We recommend the Hilti
(HUD-1 6 x 30) for the mounting.

Connecting14

Wireless subwoofer connection

LED indicator of wireless subwoofer

LED Color Status

Green

2

(Blink)

Connecting

Green The connection is completed.

Red The wireless subwoofer is

O (No
display)

Setting up the wireless subwoofer
for the first time

1. Connect the power cord of the wireless
subwoofer to the outlet.

2. Turn on the main unit : The main unit and
wireless subwoofer will be automatically
connected.

Manually pairing wireless subwoofer

When your connection is not completed, you can
see the red LED or the blinking of green LED on
the wireless subwoofer and the subwoofer does
not make sound. To solve the problem, follow the
below steps.

1. Adjust volume level of the main unit to
minimum.

-”VOL MIN” appears on the display window.

2. Press and hold (Mute) on the remote control
for about 3 seconds.

-“WL RESET” appears on the display window
briey.

The connection is trying.

in standby mode or the
connection is failed.

The power cord of wireless
subwoofer is disconnected.

3. If the LED of the wireless subwoofer already
blinks in green continually, you can skip this
step.

Press and hold PAIRING on the back of the

wireless subwoofer for more than 5 seconds.

-The LED of the wireless subwoofer lights up
alternately in red and green.

4. Disconnect the power cord of the main unit
and the wireless subwoofer.

5. Connect them again after the LED of the main
unit and the wireless subwoofer is fully turned
off.

The main unit and the wireless subwoofer will

be paired automatically when you turn on the
main unit.

-When the connection is completed, you can
see the green LED on the subwoofer.

Note

,

yIt takes a few seconds (and may take longer)

for the main unit and the subwoofer to
communicate with each other and make
sounds.

yThe closer the main unit and the subwoofer,

the better sound quality. It is recommended
to install the main unit and the subwoofer
as close as possible and avoid the cases
below.

-There is a obstacle between the main
unit and the subwoofer.

-There is a device using same frequency
with this wireless connection such as a
medical equipment, a microwave or a
wireless LAN device.

Connecting 15

Connection overview

Connect or disconnect the jack in order of the
image.

OUT

(TV ARC)

IN 1

or

Connecting to your TV

Please connect with this unit and TV using the
optical digital cable or HDMI cable considering the
state of the TV.

Using an OPTICAL cable

1. Connect the OPT. IN 1 or OPT. IN 2 jack on the
back of the unit to OPTICAL OUT jack on the TV
using an OPTICAL cable.

Optical cable

2. Set the input source to OPTICAL. Press
repeatedly FUNC on the remote control or
F on the unit until the function is selected.

To directly select the OPTICAL 1 or OPTICAL 2

function, press OPTICAL on the remote control.

Note

,

yYou can enjoy the TV audio through the

speakers of this unit. In the case of some
TV models, you must select the external
speaker option from the TV menu. (For
details, reference your TV user manual.)

ySet up the sound output of TV to listen to

the sound through this unit :
TV setting menu [ [Sound] [ [TV Sound
output] [ [External speaker (Optical)]

yDetails of TV setting menu vary depending

on the manufacturers or models of your TV.

2

Connecting

Connecting16

LG Sound Sync

You can control some functions of this unit by
your TV’s remote control with LG Sound Sync. It is
compatible with the LG TV that is supported LG
Sound Sync. Make sure of the LG Sound Sync logo
on your TV.

2

Controllable function by LG TV’s remote control :

Connecting

Volume up/down, mute

Refer to the TV’s instruction manual for the details
of LG Sound Sync.

Make one of the following connections, depending
on the capabilities of your equipment.

Note

,

yYou can also use the remote control of

this unit while using LG Sound Sync. If you
use TV's remote control again, the unit
synchronizes with the TV.

yWhen the connection fails, make sure of the

condition of the TV and power.

yMake sure of the condition of this unit and

the connection in the cases below when
using LG Sound Sync.

-Turn o the unit.

-Changing the function to the others.

-Disconnecting the optical cable.

yThe amount of time to turn o this unit is

dierent depending on your TV when you
set AUTO POWER function to ON.

With wired connection

1. Connect your LG TV to the unit by using an
optical cable.

Optical cable

2. Set up the sound output of TV to listen to the
sound through this unit :
TV setting menu [ [Sound] [ [TV Sound
output] [ [LG Sound Sync (Optical)]

3. Turn on the unit by pressing 1 (Power) on the
remote control.

4. Select OPTICAL function by using FUNC on
the remote control or F on the unit until the
function is selected.

You can see “LG OPT” on the display window

if connecting normally between this unit and
your TV.

Note

,

Details of TV setting menu vary depending on
the manufacturers or models of your TV.

With wireless connection

1. Turn on the unit by pressing 1 (Power) on the
remote control.

2. Select LG TV function by using FUNC on
the remote control or F on the unit until the
function is selected.

3. Set up LG Sound Sync (Wireless) on the TV. Refer
to the TV’s instruction manual.

“PAIRED” appears on the display window for

about 3 seconds and then you can see “LG TV”
on the display window if connecting normally
between this unit and your TV.

Note

,

If you turned o the unit directly by pressing

(Power), LG Sound Sync (Wireless) will be

1

disconnected. To use this function again, you
should reconnect the TV and the unit.

Connecting 17

Using an HDMI cable

If you connect this unit to a TV that supports HDMI
CEC and ARC (Audio Return Channel), you can
enjoy the TV audio through the speakers of this unit
without connecting the optical cable.

Connect the HDMI OUT (TV ARC) jack on the back
of the unit to ARC jack on the TV using an HDMI
cable.

HDMI cable

OUT

(TV ARC)

Note

,

yHDMI CEC (Consumer Electronics Control):

Using a single remote control, you have the
ability to operate CEC compatible devices
(TV, Sound Bar, Blue-ray player, etc.)

yYou can also enjoy extra functions such as

Bluetooth with FUNC on remote control
or F on this unit. When you go back to live
TV channel after using the extra functions
(Bluetooth) of this audio system, you should
choose your preferred speaker on TV to
enjoy the sound from this audio system
again.

HDMI cable Checklist

Some HDMI cables do not support the ARC
function, this can result in no sound output.

When connecting this unit to the TV, if there is no
sound, there might be a problem with the HDMI
cable. Therefore connect this unit to the TV and
check whether the Type A, High speed HDMI™
Cable with Ethernet.

STANDARD HDMI CABLE WITH ETHERNET

HIGH SPEED HDMI CABLE

HIGH SPEED HDMI CABLE WITH ETHERNET

(X)

(X)

(O)

Enjoy rich sound broadcast of the channel with the sound bar

Connection through HDMI Cable

Your television must support the newest HDMI
features (HDMI CEC1) / ARC (Audio Return Channel))
to fully enjoy the Live broadcasting channel with
audio system through an HDMI cable. Unless your
TV supports these HDMI features, the audio system
should be connected through an OPTICAL cable.

1) HDMI CEC (High-Denition Multimedia Interface
Consumer Electronics Control)

Consumer Electronics Control (CEC) is an HDMI
feature designed to allow the user to command
and control the CEC-enabled devices, that are
connected through HDMI by using only one of
their remote controls.

Trade names for CEC are SimpLink (LG) , Anynet+

※

(Samsung), BRAVIA Sync (Sony), EasyLink (Philips),
etc.

2

Connecting

Connecting18

What is SIMPLINK?

Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s with
SIMPLINK are connected through HDMI connection.

Controllable functions by LG TV’s remote control :

2

Power on/o, volume up/down, etc.

Connecting

Refer to the TV owner’s manual for the details of
SIMPLINK function.

LG TV’s with SIMPLINK function has the logo as
shown above.

Note

,

yDepending on the state of the unit, some

SIMPLINK operation may dier from your
purpose or not work.

yDepending on a TV or a player which

is connected with this unit, SIMPLINK
operation may dier from your purpose.

ARC (Audio Return Channel) function

The ARC function enables an HDMI capable TV to
send the audio stream to HDMI OUT of the unit.

To use this function :

-Your TV must support the HDMI-CEC and ARC
function and the HDMI-CEC and ARC must be
set to On.

-The setting method of HDMI-CEC and ARC may
dier depending on the TV. For details about
ARC function, refer to your TV manual.

-You must use the HDMI cable (Type A, High
Speed HDMI™ cable with Ethernet).

-You must connect the HDMI OUT on the unit
with HDMI IN of the TV that supports ARC
function using an HDMI cable.

-You can connect only one Sound bar to TV
compatible with ARC.

Note

,

yARC function is automatically selected when

ARC signal comes in from TV, no matter
what kind of the function you are using.

yYou can enjoy the TV audio through the

speakers of this unit. In the case of some
TV models, you must select the external
speaker option from the TV menu. (For
details, reference your TV user manual.)

ySet up the sound output of TV to listen to

the sound through this unit :
TV setting menu [ [Sound] [ [TV Sound
output] [ [External speaker (HDMI ARC)]

yDetails of TV setting menu vary depending

on the manufacturers or models of your TV.

Connecting 19

Additional information for HDMI

yWhen you connect an HDMI or DVI compatible

device make sure of the following:

- Try switching off the HDMI/DVI device and this
player. Next, switch on the HDMI/DVI device
and leave it for around 30 seconds, then switch
on this player.

- The connected device’s video input is set
correctly for this unit.

- The connected device is compatible with
720 x 576p, 1280 x 720p, 1920 x 1080i or
1920 x 1080p video input.

yNot all HDCP-compatible HDMI or DVI devices

will work with this player.

- The picture will not be displayed properly with
non-HDCP device.

Note

,

yIf a connected HDMI device does not accept

the audio output of the player, the HDMI
device’s audio sound may be distorted or
may not output.

yChanging the resolution when the

connection has already been established
may result in malfunctions. To solve the
problem, turn o the player and then turn it
on again.

yWhen the HDMI connection with HDCP

is not veried, TV screen is changed to
black screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.

yIf there are noises or lines on the screen,

please check the HDMI cable (length is
generally limited to 4.5 m(15 ft).

yYou cannot change the video resolution

in the HDMI IN mode. Change the video
resolution of the connected component.

yIf the video output signal is abnormal when

your personal computer is connected to
HDMI IN jack, change the resolution of your
personal computer to 576p, 720p, 1080i or
1080p.

Optional equipment connection

HDMI connection

For enjoying sound only

You can enjoy the sound from the external device
you connect.

IN 2 IN 3

IN 1

To the Blu-ray disc player,
DVD player, etc.

1. Connect HDMI IN 1, HDMI IN 2 or HDMI IN 3 jack
on the back of the unit to HDMI OUT jack on the
audio device such as Blu-ray disc player, DVD
player, etc.

2. Set the input source to HDMI IN 1, HDMI IN
2 or HDMI IN 3. Press repeatedly FUNC on
the remote control or F on the unit until the
function is selected.

2

Connecting

Connecting20

For enjoying both sound and picture

You can enjoy both sound and picture from the
external device you connect.

2

Connecting

IN 1

1. Connect HDMI IN 1, HDMI IN 2 or HDMI IN 3 jack
on the back of the unit to HDMI OUT jack on the
external device such as Blu-ray disc player, DVD
player, etc.

2. Connect HDMI OUT (TV ARC) jack on the back
of the unit to HDMI IN jack on the TV.

3. Set the input source to HDMI IN 1, HDMI IN
2 or HDMI IN 3. Press repeatedly FUNC on
the remote control or F on the unit until the
function is selected.

Note

,

yWith the unit connected to external devices

and TV as above illustration, TV will output
picture and sound from external devices
when the unit is turned o in HDMI IN
mode.

yHDMI OUT jack is for TV connection. Even

though PCM multi channel is inputted to
the unit through an HDMI cable, the unit
can only output 2 channel to TV.

yAudio sources without any transformation

pass through this unit when this unit is
turned o.

IN 2 IN 3

OUT

(TV ARC)

PORT. (Portable) IN connection

Listening to music from your
portable player

The unit can be used to play the music from many
types of portable players or external devices.

1. Connect the portable player to the PORTABLE
IN connector of the unit.

2. Turn the power on by pressing 1 (Power).

3. Select the PORTABLE function by pressing
FUNC on the remote control or F on the unit
until the function is selected.

4. Turn on the portable player or external device
and start playing it.

Connecting 21

OPTICAL IN connection

Connect an optical output jack of external devices
to the OPT. IN jack.

Optical cable

1. Connect the OPT. IN 1 or OPT. IN 2 jack on the
back of the unit to optical out jack of your TV (or
digital device etc.)

2. Select the input source to OPTICAL by pressing
FUNC on the remote control or F on the unit
until the function is selected.

To directly select the OPTICAL 1 or OPTICAL 2

function, press OPTICAL on the remote control.

3. Listen to sound from the connected device.

4. Press OPTICAL to exit from OPTICAL.
Function is retuned to previous one.

Connecting IR Blaster

IR blaster is supplied as an accessory with the unit
in order to communicate well with the remote
control and the TV.

Remote control of your TV may not be operated if
the unit hides the remote sensor of the TV.

You can solve the problem by connecting IR blaster
with LG TV.

2

Connecting

Remote sensor
of TV

Sensor of
IR Blaster

IR BLASTER

1. Remove the protective vinyl of IR blaster.

2. Put IR blaster on the back of the unit with the
sensor of IR blaster facing the remote sensor of
the TV.

3. Connect the end of IR blaster to IR BLASTER jack.

Caution

>

yDo not block ventilation when you put IR

blaster on the unit.

yDo not disconnect the power cord. If you

want to use IR blaster, keep the unit on
standby mode.

Note

,

Depending on your TV, some or all buttons
may not be function on the TV.

Connecting22

Understanding Network Connection

Basic Connection

A

Wired or Wi-Fi connection to router.

B

Wired and wireless connection.

You can use multiple speakers in a multi-room conguration.

2

Connecting

Router

A

Router

B

Router

LAN

OR

LAN

Speaker

Speaker

Speaker (Main)

Speaker (Add)

Group playback using Music Flow Player app

You can use multiple speakers in a multi-room conguration. (page 42)

Group setting via
Music Flow Player
app

Download

Music Flow Player app