LG HT903WA-A2 Owner’s Manual

Model: HT903WA(HT903WA-A2, SH93WA-F/C/L/R/W, W93-T2)

Unique Features

P/NO : MFL56941197

5.1ch ez Set-up

Listen sound from TV, DVD and Digital Device with vivid

5.1ch mode.

Go to page 18

Full HD up-scaling (1080p)

View Full HD picture quality with simple setup.

Go to page 13

USB Direct Recording

Record music from CD to your USB device.

Go to page 20

Portable In

Listen to music from your portable device (MP3, Notebook, etc).

Go to page 20

HT903WA-A2_DARELLK_ENG_1197 6/27/08 10:03 PM Page 1

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE

COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction has been adhered to.

CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

Safety Precaution

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

HT903WA-A2_DARELLK_ENG_1197 6/27/08 10:03 PM Page 2

Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

To fix the power cable of wireless speakers . . . . . . . .6

LED indicator of Wireless Transmitter . . . . . . . . . . . . .7

Initial setting an ID of Transmitter . . . . . . . . . . . . . . . .7

Setting an ID of Wireless Transmitter . . . . . . . . . . . . .7

Hooking up the unit . . . . . . . . . . . . . . . . . . . . . . . . .8-9

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

OSD Initial language settings . . . . . . . . . . . . . . . . . .12

Initial Setting the Area Code . . . . . . . . . . . . . . . . . . .12

Adjust the settings . . . . . . . . . . . . . . . . . . . . . . . .12-14

Setting the sound mode . . . . . . . . . . . . . . . . . . . . . .14

Displaying Disc Information . . . . . . . . . . . . . . . . . . .15

Playing a disc or file . . . . . . . . . . . . . . . . . . . . . .15-17

Viewing photo files . . . . . . . . . . . . . . . . . . . . . . . . . .17

Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . .18

5.1ch ez Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Listening to music from your USB device . . . . . . . . .19

Recording music from CD to your USB device . . . . .20

Listening to music from your portable player . . . . . . .20

Language Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Types of Playable Discs . . . . . . . . . . . . . . . . . . . . . .23

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

What is SIMPLINK?

Some functions of this unit are controlled by TV’s remote control when this unit and LG TV with SIMPLINK are connected through HDMI connection.

• Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc.

• Refer to the TV owner’s manual for the details of SIMPLINK function.

• LG TV with SIMPLINK function has the logo as shown above.

• Use a higher version cable than 1.2A HDMI cable.

Welcome to your new Wireless DVD Receiver

POWER: This unit operates on a mains supply of 200-240V, 50/60Hz.

WIRING: This unit is supplied with a BSI 1363 approved 13 amp mains plug, fused

at 5 amp. When replacing the fuse always use a 5 amp BS 1362, BSI or ASTA

approved type. Never use this plug with the fuse cover omitted. To obtain a replace-

ment fuse cover contact your dealer. If the type of plug supplied is not suitable for

the mains sockets in your home, then the plug should be removed and a suitable

type fitted. Please refer to the wiring instructions below:

WARNING: A mains plug removed from the mains lead of this DVD player must be

destroyed. A mains plug with bared wires is hazardous if inserted in a mains socket.

Do not connect either wire to the earth pin, marked with the letter E or with the earth

symbol or coloured green or green and yellow. If any other plug is fitted, use a

5 amp fuse, either in the plug, or at the distribution board.

IMPORTANT: The wires in this mains lead are coloured in accordance with the fol-

lowing codes:

- BLUE: NEUTRAL, BROWN: LIVE - As the colours of the wires in the mains lead

of this DVD player may not correspond with the coloured marking identifying the ter-

minals in your plug, proceed as follows: The wire which is coloured blue must be

connected to the terminal which is marked with the letter N or coloured black. The

wire which is coloured brown must be connected to the terminal which is marked

with the letter L or coloured red.

In NIGERIA

HT903WA-A2_DARELLK_ENG_1197 6/27/08 10:03 PM Page 3

Setting up

Connect the red end of each wire to the terminals marked +(plus) and the black end to the terminals marked - (minus).

Connect the wires to the speakers.

Connect the other end of each wire to the correct speaker according to the colour coding

Attaching the speakers to the DVD receiver

You will have received six speaker cables.

Each one is colour-coded by a band near each end and connects one of the six speakers to the DVD receiver.

Connect the wires to the DVD receiver.

Match each wire’s coloured band to the same coloured connection terminal on the rear of the DVD receiver. To connect the cable to the DVD receiver, press each plastic finger pad to open the connection terminal. Insert the wire and release the finger pad.

1 Draw the speaker cord through the hole on the speaker.

2 Attach the speakers to the speaker stands by rotating the screw.

The speakers are detached from the speaker stands.

Assembling the Speakers

Green

Orange

Red

White

Center

Sub Woofer

Front

Above screen, directly in front of you.

In front of you, to the right of the screen.

In front of you, to th e left of the screen.

POSITION

SPEAKER

COLOR

To connect the cable to the speakers, press each plastic finger pad to open the connection terminals on the base of each speaker. Insert the wire and release the finger pad.

HT903WA-A2_DARELLK_ENG_1197 6/27/08 10:03 PM Page 4

Attaching the Wireless Transmitter to the DVD receiver

Connect the DC power cable to the unit and transmitter.

Connect the SOUND SIGNAL connector of the Wireless Transmitter and rear (right, left) speaker of the main set with the sound signal cable.

Connecting the power cord

Connect the power cord of the Wireless speakers to the outlet.

Setting up

HT903WA-A2_DARELLK_ENG_1197 6/27/08 10:03 PM Page 5

To fix the power cable of wireless speakers

To fix the power cable of wireless speakers, insert the power cable of wireless speakers in to the hole on the speakers.

Be careful of the following

• Be careful to make sure children do not put their hands or any objects into the *speaker duct.

*Speaker duct: A hall for plentiful bass sound on speaker cabinet(enclosure).

• Set the distance between this unit and Wireless Speakers within 10m.

• Optimum performance can be implemented only when the Wireless Transmitter and the Wireless Speakers within distance of 2m to 10m is used since communication failure may occur if longer distance is used.

• Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to –. If the cables are reversed, the sound will be distorted and will lack bass.

•

It takes a few seconds (and may take longer) for the

Wireless Transmitter

and

Wireless Speakers

to communicate with each other.

• When the unit is turned off, the Wireless Transmitter is in standby mode (off) automatically after about 10 seconds.

• If the Wireless Transmitter is turned off, the Wireless Speakers will not function.

• Do not fix the speaker cables in the hole on the speakers

HT903WA-A2_DARELLK_ENG_1197 6/27/08 10:03 PM Page 6

Be careful of the following

If there is a strong electromagnetic wave product nearby, interference may occur. Put the unit (Wireless Speakers and main unit) away from there.(Ex: Microwave oven) If there is no audio signal for longer than 10 minutes, the Wireless Speakers and Wireless Transmitter will be automatically switched to standby mode. In power saving mode, both LEDs will turn red. LEDs will turn blue when there is any audio signal back. If you operate main unit then wireless speakers (rear speakers) sound within a few seconds in standby mode.

LED indicator of Wireless Transmitter

BLUE The main set is turned on, everything is connected

and transmitting.

RED The wireless transmitter is in standby mode.

OFF (No display) The DC cable is disconnected to the unit.

LED color

Operation

Setting an ID of Wireless Transmitter

1Disconnect power cord of wireless speakers: -

2Press the ID. button for more than about

3 seconds: The blue LED indicator will quickly flicker. ID.

3 Connect power cord of wireless speakers.: -

If an interference is occurred or you use a new wireless speaker, set the ID.

ON Wireless Kit

Initial setting an ID of Transmitter

ON REMOTE

1 Connect the SOUND SIGNAL connector of

transmitter and the rear (right, left) speaker terminals of main unit with the SOUND SIGNAL cable: -

2 Connect the DC IN connector of transmitter

and the transmitter connector of main unit with the DC power cable.: -

3 Connect power cord of each wireless

speakers to the wall power outlet.: -

4Turn the main unit ON.: POWER

Blue LEDs of transmitter will flicker and Blue LEDs of wireless speakers will flicker in turn, then the Blue LEDs of both transmitter and wireless speakers will stay on when the wireless system works normally.

HT903WA-A2_DARELLK_ENG_1197 6/27/08 10:03 PM Page 7

Hooking up the unit

a Connect jacks on the unit and your TV (DVD player or Digital Device etc.) using the cables.

b Plug the power cord into the power source.

Audio In connection

The unit’s Audio jacks are colour coded (red for right audio and white for left audio). If your TV has only one input for audio (mono), connect it to the left (white) audio jack on the unit.

AM/FM connection

AM - Connect the AM loop aerial to the DVD receiver. FM - Connect the FM aerial. The reception will be its best when the two loose ends of the aerial are in a straight and horizontal line.

Video Out connection

Connect the VIDEO OUTPUT jack on the unit to the corresponding input jack on your TV using a Video cable.

Component Video connection

Connect the COMPONENT/PROGRESSIVE SCAN OUTPUT jacks on the unit to the corresponding input jacks on your TV using a Y PB PR cable.

HT903WA-A2_DARELLK_ENG_1197 6/27/08 10:03 PM Page 8

+ 16 hidden pages