LG HSC5650 Quick Setup Guide

QUICK
SETUP
GUIDE
FOR HCS5650
Setup requires LG Setup Remote #124-213-07. Note:
Cloning multiple HCS5650 units requires an LG #LT2002 (TLL-1100A can also be used) cloner. Con­tact your LG Account Manager at 877-793-6484 for information on how to obtain these.
STEP 1. CONNECT THE HCS5650 TO MONITOR
Theorderin which you connectthe HCS5650tothe monitormaybe a crit­ical factor in a successful setup. Wait to turn on monitor. Make sure to first connect these cables from the HCS5650 to the monitor 1) HDMI, 2) RS-232C, 3) power cord and 4) RF Coaxial cable. The HCS5650 cycles at“plug-in” andlocates amonitorwith whichto integrate.Ifnomonitoriscon­nected at “plug-in”, it may not setup properly.
STEP 2. POWER UP MONITOR
After connectingas explainedabove, turn on the HCS5650/monitor using the setup remote. It is important to only hit the power button one time as the initial power-up may take 30 seconds from the time the power button is hit.
STEP 3. ENTER INSTALLER MENU
Aim the setup remote at the TV and toggle the menu button until the menu locks up. Then enter the installer’s menu code (9876) and press Enter. You will now see the installers menu.
STEP 4. SET TV TO DEFAULT
Using the arrowkeys onthe remote, select item 117 which is Factory Default. Change the setting to 1 and press enter.
STEP 5. TUNING SETTINGS Go back into the Installers menu using the directions above:
Set Band Mode (Item 003) – Default is “1” for cable; Set to “0” for
Broadcast
Scan Mode (Item 013) – Default is set to “1” to enabling TV to power
off after scrolling through all of the channels once the ‘2+5+5+Menu’ step is performed. This is generally desirable whenTV is being usedwith older pillow speaker/remotes which lack a TV Power Button. Option: Setto “0” to allowscrolling through channels continuously without pow­ering off the TV.
Disable unwantedinputs(One ormore of the following Installer Menu
Items: 035, 036, 038, 039, 087, 091, 092) – Set to “0” todisablese­lectedinput(s) fromshowing up inthechannel lineup. Without disabling an input, it will appear in the channel line up when channeling up or down. Thisisdoneto accommodate hospitalsusingDVD playersetc that desire patients to easily select the DVD player input by simply scrolling through the channels until the DVD input appears.
Panel Delay (Item 110): Make sure this Item is set on “4”. Default has
been “8”, however we are changing itto “4” with future shipments. This will make the monitor turn on faster (and keep it from going to hiberna­tion while the monitor is powering on).
Press the “Enter” or“OK” Button two or three times to exit the Installer menu and save your changes.
STEP 6. SET CHANNELS Enter the TV’s On-Screen Menu by pressing the Menu Button on the re­mote.
Perform the User Menu Set Up “AUTO PROGRAM” to generate your
Channel Map
Scan through the available channels using the Channel Up/DownEdit your channels to remove any unwanted channelsAdd logos to your channels as needed
STEP 7. LOCK CHANNELS & SETTINGS
Enter the Installers menu again to “set” your TV with the new settings. Upon entering the installers menu (previous directions), key in “2+5+5” and then press the “Menu” Button. (Caution: If you key in “2+5+5” and then the “Enter” Button, nothing will happen.) When you enter“2+5+5+Menu”, the Installer Menu is cleared from the screen and you will see your channels flash as the TV scrolls through all the settings and then stores them.
STEP 8. ADDING CUSTOM CHANNEL LOGOS
You can addcustom channel logos foranalog channels if youcould not find theappropriate logofora channel within the regularsetup menu. Upon en­tering the installers menu, press “2+5+4” and then the “Menu” Button. Use theChannelUp/Downbutton to locate desiredchannel and press the Right Arrow Button. You will see an “I” (Icon) placed on the ChannelIndicator.By pressingthe Right Arrow Button, the “I” changes to a “1”,so you can create seven-character length customlogos. Use the Up/downto select the desired alphanumeric character. By pressing the Right Arrow Button, the “1” changes to “2”. Use the Up/Down Arrows to select the desired character. You can even create a message on a selected channel like “Welcome”.
STEP 9. CHANNEL OVERRIDE
If you want to keep your patients from directly accessing channels not in your channel lineupyoucan now enter theinstallersmenu and go to “Chan­nel Override” (Item 28). Set this item to “0”.
Follow thedirections in yourcloner box to clone multiple TV’s from the “Mas­ter” setup TV.
This Guide should get you started. See the Operators Manual for more detailed settings.
w w w . LG c o m me r c i a l . c o m
LG Electronics U.S.A., Inc.
Commercial Products Division
2000 Millbrook Drive Lincolnshire, IL 60069
Healthcare: 877.793.6484
E-mail: healthcare1@lge.com
Guide_HSC5650_020908_PR
© Copyright 2009 LG Electronics USA, Inc. All Rights Reserved. “LG Life’s Good” is a registered trademark of LGCorp.
Printed in the USA. March 2009
Loading...