LG FP1482D6 Manual book [id]
OWNER’S MANUAL
WASHING MACHINE
FP1482D6
MFL67791852
www.lg.com/id
Before beginning installation, read these instructions carefully.
This will simplify installation and ensure that the washer is installed
correctly and safely. Leave these instructions near the washer
after installation for future reference.
PT. LG Electronics Indonesia
Gandaria 8 Office Tower, 31st Floor
Jl. Sultan Iskandar Muda,
Kebayoran Lama Utara–Kebayoran Lama
11240, INDONESIA
ENGLISH BAHASA
2
Contents....................................2
Product Features......................3
Important safety instructions
Important safety instructions....................4
Basic safety precautions..........................5
Save these instructions............................6
Specifications...........................7
Installation
Removing packing ...................................8
Removing transit bolts .............................8
Installation place requirements ................9
Connecting water supply hose...............11
Installation of drain hose........................13
Leveling .................................................14
How to use washer
Operating washing machine ..................16
Care before washing..............................17
Washing program table..........................18
Extra options..........................................19
Operating data .......................................20
Control panel .........................................21
Additional program.................................22
- Time Delay ..........................................22
- Crease Care ........................................22
- Favorite................................................22
- Pre Wash.............................................22
Options ..................................................23
- Medic Rinse.........................................23
- Wash ...................................................23
- Rinse ...................................................23
- Temp. .................................................23
- Spin .....................................................23
- Rinse+Spin ..........................................23
Other functions ......................................23
- Spin Only ............................................23
Child Lock ..............................................24
Beep On/Off...........................................24
Tub Clean ..............................................25
Door Lock & Detecting...........................25
Thank you for buying a LG Fully
Automatic Washing Machine.
Please read your owner’s manual
carefully, it provides instruction on safe
installation, use and maintenance.
Retain it for future reference.
Record the model and serial number of
your washing machine.
Model No.
Serial No.
Date of Purchase
Adding detergent
Adding detergent and fabric softener.....26
Maintenance
The water inlet filter ...............................28
The drain pump filter..............................29
Dispenser drawer...................................30
The washing drum .................................31
Cleaning your washer ............................31
Cold conditions ......................................31
Troubleshooting guide
Diagnosing Problem ..............................32
Error messages .....................................34
Using SMARTDIAGNOSIS™ ................35
Terms of warranty ..................36
Contents
3
ENGLISH
추가선택 예약
Inverter Direct Drive system
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
Low noise speed control system
By sensing the amount of load and balance, it evenly distributes load
to minimize the spinning noise level.
Child Lock
The Child Lock prevents children from pressing any button to change
the settings during operation.
More economical with Intelligent Wash system
Intelligent Wash System detects the size of load and water temperature,
and then determines the optimum water level and washing time to
minimize energy and water consumption.
Built-in heater
Internal heater automatically heats the water to the best temperature
on selected cycles.
Protection against creases
With the alternating rotation of the drum, creasing is minimized.
6 Motion
Washer is able to perform various drum actions or a combination of
different actions depending on the wash program selected.
Combined with a controlled spin speed and the ability of the drum to
rotate both left and right, the wash performance of the machine is greatly
improved, giving you perfect results every time.
Product Features
4
Important safety instructions
For your safety, the information in this manual must be followed to minimize the risk of fire or
explosion, electric shock, or to prevent property damage, injury to persons, or death.
READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION
BEFORE USE.
WARNING
You can be killed or seriously injured if you don’t follow instructions.
Your Safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance.
Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER,
WARNING or CAUTION.
These words mean:
WARNING
You may be slightly injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance
of injury, and tell you what can happen if the instructions are not followed.
CAUTION
You will be killed or seriously injured if you don’t immediately follow instructions.
DANGER
5
ENGLISH
Important safety instructions
To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic
precautions, including the following:
WARNING
• Before installation, check exterior
damages. If it has, do not install.
• Do not install or store the washer
where it will be exposed to the
weather.
• Do not tamper with controls.
• Do not repair or replace any part of
the washer or attempt any servicing
unless specifically recommended in
the user-maintenance instructions or
published user-repair instructions
that you understand and have the
skills to carry out.
• Keep the area underneath and around
your appliances free of combustible
materials such as lint, paper, rags,
chemicals, etc.
• The appliance is not intended for use
by young children or infirm persons
without supervision. Do not allow
children to play on, with, or inside this
or any other appliance.
• Keep small animals away from the
appliance.
• Do not leave the washer door open.
An open door could entice children to hang
on the door or crawl inside the washer.
• Never reach into washer while it is
moving. Wait until the drum has
completely stopped.
• The laundry process can reduce the flame
retardant of fabrics.
To avoid such a
result, carefully follow the garment
manufacturer’s wash and care
instructions.
• Do not wash or dry articles that have
been cleaned in, washed in, soaked
in, or spotted with combustible or
explosive substances (such as wax,
oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.)
which may ignite or explode. Oil may
remain in the tub after a whole cycle resulting
in fire during drying.
So, do not load oiled clothes.
• Do not slam the washer door closed
or try to force the door open when
locked. This could result in damage to the
washer.
• When the machine runs high
temperature, the front door may be
very hot. Don’t touch it.
• To minimize the possibility of electric
shock, unplug this appliance from the
power supply or disconnect the
washer at the household distribution
panel by removing the fuse or
switching off the circuit breaker
before attempting any maintenance or
cleaning.
• When unplugging power cord, do not
pull out by grasping the cord.
Otherwise, the power cord may be damaged.
• Never attempt to operate this
appliance if it is damaged,
malfunctioning, partially
disassembled, or has missing or
broken parts, including a damaged
cord or plug.
■ Basic safety precautions
6
Important safety instructions
■ Basic safety precautions
To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic
precautions, including the following:
WARNING
• Before discarding an old machine
unplug it. Render the plug useless.
Cut off the cable directly behind the
appliance to prevent misuse.
• When a product was under water,
Please call service center. There is a
risk of electric shock and fire.
• Appliance connected to the water
mains using new hose-sets. Old hosesets should not be reused.
• To reduce the risk of personal injury,
adhere to all industry recommended
safety procedures including the use
of long sleeved gloves and safety
glasses. Failure to follow all of the safety
warnings in this manual could result in
property, personal injury or death.
• Do not push down the door
excessively, when washer door open.
This could topple over the washer.
■ Save these instructions
Improper connection of the equipment-grounding conductor can result in electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the
outlet, have a proper outlet installed by a qualified electrician.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a path of least resistance for electric current.
This appliance is equipped with a cord having an equipment-grounding conductor and
grounding plug. The plug must be plugged into an appropriate outlet that is properly installed
and grounded in accordance with all local codes and ordinance.
• Do not use an adapter this will defeat the grounding plug.
• If you don’t have the proper outlet, consult an electrician.
WARNING
7
ENGLISH
■ Name : Front loading washing machine
■ Power supply : 220 V~, 50 Hz
■ Size : 600 mm(W) 590 mm(D) 850 mm(H)
■ Weight : 66 kg
■ Max.Watt : 2000 W
■ Wash capacity : 9 kg
■ Permissible water pressure : 100 - 1000 kPa (1.0 - 10.0 kgf / cm
2
)
The appearance and specifications may vary without notice to improve the quality of the unit.
(For detergent and
fabric softener)
Drawer
Drain hose
Transit bolts
Power plug
Control panel
Drain pump filter
Lower cover cap
• If the supply cord is damaged,
it must be replaced by the
manufacturer or its service agents
or a similarly qualified person in
order to avoid a hazard.
Drum
Door
Drain plug
Adjustable feet
Specifications
■
Accessories
Inlet hose(1EA) Option : Hot/Cold(2EA)
Spanner
■ Removing packing
1. Remove the cardboard box and
styrofoam packing.
2. Lift the washing machine and remove
the base packing.
3. Remove the tape securing the power
supply cord and drain hose.
4. Remove the inlet hose from the drum.
1. Unscrew the 4 bolts with
the spanner supplied.
2. Take out the 4 bolts along with the
rubber bungs by slightly twisting the
bung.
3. Close the holes with the caps supplied.
To prevent internal damage during transport, the 4 special bolts are locked.
Before operating the washer, remove the bolts along with the rubber bungs.
If they are not removed, it may cause heavy vibration, noise and malfunction.
■ Removing transit bolts
Transit bolt
8
Installation
WARNING
• Packaging material (e.g. Films, Styrofoam) can be dangerous for children.
There is a risk of suffocation ! Keep all packaging well away from children.
NOTE
• Keep the spanner provided for
future use.
NOTE
• Keep the transit bolts for future use.
Spanner
Washer
Base Packing
9
ENGLISH
• Level floor :
Allowable slope under entire washer is 1˚.
• Power outlet :
Must be within 1.5 meters of either side of location of washer.
Do not overload the outlet with more than one appliance.
• Additional Clearance :
For Wall, 10cm:rear / 2cm : right & left side
Do not place or store laundry products on top of washer at
any times.
They can damage the finish or controls.
■ Installation place requirements
Positioning
Location
• Install the washer on a flat hard floor.
• Make sure that air circulation around the washer is not impeded by carpets, rugs, etc.
• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under
the washer.
• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an
insulating(85x60cm) covered with aluminum foil on the side facing the cooker or stove,must be inserted
between the two appliance.
• The washer must not be installed in rooms where the temperature can drop below 0°C.
• Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of a
breakdown.
• With the washer installed, adjust all four feet using the transit bolt spanner provided ensuring the appliance
is stable, and a clearance of approximately 20mm is left between the top of the washer and the underside of
any work-top.
• This equipment is not designed for maritime use or for use in a mobile installations such as caravans,
aircraft etc.
• Do not use an extension cord or double adapter.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly
qualified person in order to avoid a hazard.
• Always unplug the machine and turn off the water supply after use.
• Connect the machine to an earthed socket in accordance with current wiring regulations.
• The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel.
Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your
local service center
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen
hoses may burst under pressure. The reliability of the electronic control unit may be impaired at
temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Place the
washing machine at room temperature for a few hours before putting it into operation.
Electrical connection
Installation
Washer
approx.
2cm
10
Installation
CAUTION
CAUTION concerning the Power cord
• Most appliances recommend they be placed upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance and has no additional outlets or branch
circuits. Check the specification page of this owner's manual to be certain.
• Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are
dangerous. Any of these conditions could result in an electric shock or fire.
• Periodically examine the cord of your appliance, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by an authorized servicer.
• Protect the power cord from physical or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the appliance.
If the appliance is supplied from a cord extension set or an electrical portable outlet
device, The cord extension set on electrical portable outlet device must be positioned
so that it is not subject to splashing or ingress of moisture.
CAUTION
• The appliance is not intended for use by young children or infirm persons without
supervision.
• Young children should be supervised to ensure that they do not play with appliance.
11
ENGLISH
1. Unscrew the adapter ring plate and the 4
adapter retaining screws.
2. Push the adapter onto the end of the tap
so that the rubber seal forms a watertight
connection. Tighten the adapter ring plate
and the 4 screws.
3. Push the water supply hose vertically
upwards so that the rubber packing within
the hose can adhere completely to the
tap and then tighten it by screwing it to
the right.
• Water supply pressure must be between 100 kPa and 1000 kPa (1.0 - 10.0 kgf / cm2).
• Do not strip or crossthread when connecting inlet hose to the valve.
• If the water supply pressure is more than 1000 kPa, a decompression device should be installed.
• Periodically check the condition of the hose and replace the hose if necessary.
Type-A : Connecting Screw-type hose to tap with thread
• Screw the hose connector onto water
supply tap.
■ Connecting water supply hose
Step1 : Check rubber seal inlet hose
Step2 : Connect hose to water tap
• Two rubber seals are supplied with the
water inlet hoses.
They are used for preventing water leaks.
Make sure the connection to taps is
sufficiently tight.
Upper
connector
Rubber
packing
Plate
Water supply
hose
Fixing screw
Hose
connector
Rubber
seal
Type-B : Connecting Screw-type hose to tap without thread
Installation
1. Unscrew the adapter ring plate and
the 4 adapter retaining screws.
2. Remove the guide plate if the tap is
too large to fit the adapter.
3. Push the adapter onto the end of
the tap so that the rubber seal forms
a watertight connection.
Tighten the adapter ring plate and
the 4 screws.
4. Pull the connector latch plate down,
push the inlet hose onto the adapter,
and release the connector latch plate.
Make sure the adapter locks into place.
Please use the horizontal tap
Horizontal tap Extension tap Square tap
Ring plate
Guide plate
Latch plate
Type-C : Connecting one touch type hose to tap without thread
Step3: Connect hose to washer
• Make sure that there are no kinks in the
hose and that they are not crushed.
When your washer has two valves.
• The Inlet hose which has red connector is
for the hot water tap.
• If the washer has two valves, the energy is
saved by using hot valve.
12
Installation
NOTE
• After completing connection, if water leaks from the hose, repeat the same steps.
Use the most conventional type of faucet for water supply. In case the faucet is square or
too big, remove the spacing ring before inserting the faucet into the adaptor.
NOTE
• After connecting inlet hose to water
tap, turn on the water tap to flush
out foreign substances (dirt, sand or
sawdust) in the water lines. Let
water drain into a bucket, and
check the water temperature.
13
ENGLISH
Installation of drain hose
• The drain hose should not be placed
higher than 100 cm above the floor.
Water in the washer does not drain or
drains slowly.
• Securing the drain hose correctly will
protect the floor from damage due to
water leakage.
• If the drain hose is too long, do not force
back into the washer.
This will cause abnormal noise.
• When installing the drain hose to a sink,
secure it tightly with string.
• Securing the drain hose correctly will
protect the floor from damage due to
water leakage.
about 100 cm
about 145 cm
about 105 cm
max. 100 cm
Hose
Retainer
Tie strap
Laundry tub
max. 100 cm
max. 100 cm
Installation
•
Diagonal Check
When pushing down the edges of the
washing machine top plate diagonally,
the machine should not move up and down
at all (Please, check both directions). If
machine rocks when pushing the machine
top plate diagonally, adjust the feet again.
2. If the floor is uneven, turn the adjustable feet
as required. (do not insert pieces of wood
etc. under the feet)
Make sure that all four feet are stable and
resting on the floor and then check that the
appliance is perfectly level. (use a spirit
level)
1. Leveling the washing machine properly
prevents excessive noise and vibration.
Install the appliance on a solid and level
floor surface, preferably in a corner of the
room.
■ Leveling
•
Once the washer is level, tighten the lock
nuts up towards the base of the washer.
All lock nuts must be tightened.
Raise Lower
Lock
Nut
Tighten all 4
locknuts securely
14
Installation
NOTE
• Timber or suspended type flooring
may contribute to excessive
vibration and unbalance.
NOTE
• If the washing machine is installed on a raised platform, it must be securely fastened in
order to eliminate the risk of falling off.
15
ENGLISH
Concrete floors
Wooden floors (Suspended floors)
• The installation surface must be clean, dry and level.
• Install washer on a flat hard floor.
Tile floors (Slippery floors)
• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into
70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.)
• Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.
•
Wooden floors are particularly susceptible to vibration.
•
To prevent vibration we recommend you place rubber cups under
each foot under washer at least 15mm thick, secured to at least
2 floor beams with screws.
•
If possible install the washer in one of the corners of the room, where the floor is more stable.
•
Fit the rubber cups to reduce vibration.
•
You can obtain the rubber cups (p/no.4620ER4002B) from the LG spares dept.
Rubber Cup
Installation
NOTE
• Proper placement and leveling of the washer will ensure long, regular and reliable
operation.
• The washer must be 100% horizontal and stand firmly in position.
• It must not “Seesaw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.
Operating washing machine
2. Open the door and load laundry.
1. Sort Laundry.
(Refer to 17 page)
3. Press the Power button.
4. Select a Program.
(Refer to 18~20 page)
5. Add detergent.
(Refer to 26~27 page)
6. Press the Start/Pause button.
Select options at this time
(Refer to 22~25 page)
■ Additional Program
■ Temperature
■ Spin Speed
■ Other functions
16
How to use washer
17
ENGLISH
■ Care before washing
3. Caring before loading
Combine large and small items in a load. Load large items first.
Large items should not be more than half the total wash load. Do
not wash single items.
This may cause an out-of-balance load. Add one or two similar
items.
• Check all pockets to make sure that they are empty. Items such
as nails, hair clip, matches, pens, coins and keys can damage
both your washer and your clothes.
• Close zippers, hooks and strings to make sure that these items
don’t snag on other clothes.
• Pre treat dirt and stains by brushing a little detergent dissolved in
water onto stains like collars and cuffs to help lift dirt.
• Check the folds of the flexible gasket (gray) and remove any
small articles.
• Check inside of the drum and remove any item from a previous
wash.
• Remove any clothing or items from the flexible gasket to prevent
clothing and gasket damage.
2. Sorting
To get the best results, sort clothes into loads that can be
washed with the same wash cycle.
Water temperature and spin speed and different fabrics need to
be washed in different ways.
Always sort dark colors from pale colors and whites. Wash
separately as dye and lint transfer can occur causing
discolouration of white etc. If possible, do not wash heavily
soiled items with lightly soiled one.
• Soil (Heavy, Normal, Light)
Separate clothes according to amount of soil.
• Color (White, Lights, Darks)
Separate white fabrics from colored fabrics.
• Lint (Lint producers, Collectors)
Wash lint producers and lint collectors separately.
1. Care Labels
Look for a care label on your clothes.
This will tell you about the fabric content of your garment and
how it should be washed.
Wash temperature
Normal machine wash
Permanent press
Hand wash
Sort laundry by...
Soiling
Colour
Wash
temperature
Fabric type
Delicate
Do not wash
How to use washer
NOTE
• Before the first wash, select a cycle (Cotton 60°C, add a half load of detergent) allow the unit to
wash without clothing. This will remove residues and water from the drum that may have been
left during manufacturing.
Washing program table
•
Recommended courses according to the laundry type.
18
How to use washer
Program
Description
Fabric type
Proper
Temp.
Maximum
Load
Cotton
Provides better performance by
combining various drum motions.
Provides optimized washing
performance with less energy
consumption.
Cotton
Eco
40°C
(Cold to 95°C)
60°C
(Cold to 60°C)
Rating
Rating
Color fast garments (shirts,
nightdresses, pajamas, etc) and
normally soiled cotton load
(underwear).
Within 60 mins provides better
washing performance and energy
efficiency.
Intensive
60
This cycle is suitable for casual
shirts that do not need ironing
after washing.
Polyamide, Acrylic, Polyester.
Easy
Care
40°C
(Cold to 60°C)
Less than
4.0 kg
Less than
4.5 kg
Enables various fabrics to be
washed simultaneously.
Various kind of fabrics except
special garments. (Silk/delicate,
sports wear, dark clothes, wool,
Duvet/Curtains).
Mix
40°C
(Cold to 40°C)
Baby
Care
Remove solid and protein stain and
provide better rinse performance
Lightly soiled baby wear
60°C
(95°C)
Provides less noise and vibration
and saves money by using
overnight electricity.
Color fast garments (shirts,
nightdresses, pajamas, etc) and
lightly soiled white cotton
(underwear).
Silent
Wash
40°C
(Cold to 60°C)
Remove efficiently detergent
residue in clothes
Skin Care
Fabrics which will be in direct
contact with the skin, e.g.
underwear, nappies, towelling, bed
linen, pillow and mattress covers
1 single size
This cycle is for large items such
as bed cover, pillows, sofa
covers, etc.
Cotton bedding except special
garments (delicates, wool, silk, etc.)
with filling: duvets, pillows, blankets,
sofa covers with light filling.
Duvet
40°C
(Cold to 40°C)
Sports
Wear
This cycle is suitable for sports
wear such as jogging clothes and
running wear.
Less than
2.0 kg
Less than
4.0 kg
Coolmax, Gore-tex, fleece and
Sympatex.
Dark
Wash
If it's possible for clothes to
decolourate, please use this cycle.
The cycle prevent decolorization.
(Please use detergent for colored
fabrics.)
Dark garments made from cotton
or mixed fabrics.
Delicate
This cycle is for delicate clothes
such as underwear, blouse, etc.
Delicate, easily damaged laundry.
Wool
Enables to wash wool fabrics.
(Please use detergent for
machinewashable woolens).
Machine washable woolens with
pure new wool only.
Quick 30
This cycle provides fast washing
time for small loads and lightly
soiled clothes.
Colored laundry which is lightly
soiled fast.
Cotton and mix fabrics.
(Special PROGRAM within 60
mins for normally soiled laundry).
30°C
(Cold to 40°C)
40°C
(Cold to 40°C)
30°C
(Cold to 40°C)
60°C
(Cold to 60°C)
19
ENGLISH
How to use washer
NOTE
• Neutral detergent is recommended.
• The wool cycle features gentle tumbling and low-speed spin for garment care.
•
Water Temperature: Select water temperature to suit wash cycles.
Always follow garment manufacture’s care label or instructions when washing.
Extra options
* : This option is automatically included in the cycle and can not be deleted.
** : This option is automatically included in the cycle and can be deleted.
Cotton
Cotton Eco
Easy Care
Mix
Baby Care
Silent Wash
Skin Care
Duvet
Sports Wear
Dark Wash
Delicate
Wool
Quick 30
Intensive 60
Time
Delay
Crease
Care
FavoriteProgram
Pre
Wash
Medic
Rinse
Rinse +
Spin
Time
Save
Intensive
*
** **
20
How to use washer
Operating data
Max RPM
Cotton
Cotton Eco
Easy Care
Mix
Baby Care
Slient Wash
Skin Care
Duvet
Sports Wear
Dark Wash
Delicate
Wool
Quick 30
Intensive 60
1400
1400
1000
1400
1000
1000
1400
1000
800
1400
800
800
1400
1400
Program
21
ENGLISH
■ Control panel
Power
• Press the Power button to turn power on
and off.
• To cancel the Time Delay function, the
power button should be pressed.
Program dial
• Programs are available according to the
laundry type.
• Lamp will light up to indicate selected
program.
Additional program
• Use these buttons to select the desired
cycle options for the selected cycle.
LED display
• The display shows the settings, estimated
time remaining, options, and status
messages for your washer.
The display will remain on through the
cycle.
Start/Pause
• This Start/Pause button is used to start
wash cycle or pause the wash cycle.
• If temporary stop of wash cycle is
needed, press the Start/Pause button.
• When in Pause, the power is turned off
automatically after 4 minutes.
Options
• This allows you to select an additional
cycle and will light when selected.
How to use washer
Start/Pause
button
Beep
On/Off
Power
button
Option
buttons
Additional
program
buttons
LED
display
Program
dial
SMARTDIAGNOSIS™ function is
available only for the products with
a SMARTDIAGNOSIS™ mark.
1. Press the Power button.
2. Select a cycle.
3. Touch the Time Delay button and set time
required.
4. Press the Start/Pause button.
You can set a time delay so that the washing
machine will start automatically and finish
after a specified time interval.
If the laundry is heavily soiled, “Pre Wash”
course is effective.
1. Press the Power button.
2. Select a cycle.
3. Touch the Pre Wash button.
4. Press the Start/Pause button.
Pre Wash
Time Delay
■ Additional program
22
Favorite program allows you to store
a customized wash cycle for future use.
1. Press the Power button.
2. Select a cycle.
3. Select the course.
(Washing method, number of rinses, spin
speed, water temperature etc.)
4. Touch and hold Favorite program button
for 3 seconds.
The Favorite program is now stored for future
use.
To reuse the program, select Favorite
program and press the Start/Pause.
Favorite
How to use washer
NOTE
• The delay time is the time to the end
of the programme, not the start.
The actual running time may vary
due to water temperature, wash load
and other factors.
If you want to prevent creasing, select
Crease Care option.
1. Press the Power button.
2. Select a cycle.
3. Touch the Crease Care button.
4. Press the Start/Pause button.
Crease Care
23
ENGLISH
How to use washer
• Spin Speed level can be selected by
touching 'Spin' button repeatedly.
1. Press the Power button.
2. Touch the Spin button to select RPM.
3. Press the Start/Pause.
Spin only
For best results or for cleaner rinsing.
This allows the final rinse to be heated to 40
degrees.
1. Press the Power button.
2. Select a cycle.
3. Touch the Medic Rinse button and set time
required.
4. Press the Start/Pause button.
Medic Rinse
• Time Save : This option can be used to
reduce the time of a wash program.
• Intensive : If the laundry is normal and
heavily soiled, “Intensive” option is effective.
Wash
• R++Hold : Add rinse once then after rinsing
process, the course is paused until start
button is pressed again.
• N+Hold : The course is paused until start
button is pressed again when rinse is
finished.
• Rinse++: Add rinse twice.
• Rinse+: Add rinse once.
Rinse
Spin
■ Options
■ Other functions
• By touching the Temp. button the water
temperature can be selected.
- Cold
- 30°C, 40°C, 60°C, 95°C
• Water temperature can be selected
according to the program.
Temp.
When you select "No Spin", it will still
rotate for a short time with low speed to
drain quickly.
NOTE
This can be helpful in preventing fresh stains
from setting in fabrics.
This is a separate cycle.
1. Press the Power button.
2. Select a cycle.
3. Touch the Rinse+Spin button.
4. Press the Start/Pause.
Rinse+Spin
Loading...