LG F1450ST1W Manual book

<![if ! IE]>

<![endif]>BAHASA ENGLISH

OWNER’S MANUAL

WASHING MACHINE

Before beginning installation, read these instructions carefully. This will simplify installation and ensure that the washer is installed correctly and safely. Leave these instructions near the washer after installation for future reference.

F1450ST1W

PT. LG Electronics Indonesia

Gandaria 8 Office Tower, 31st Floor

Jl. Sultan Iskandar Muda,

Kebayoran Lama Utara–Kebayoran Lama

11240, INDONESIA

MFL68801067

www.lg.com/id

Contents
Product Features......................	3
Important safety instructions
Important safety instructions .................	4
Basic safety precautions .......................	5
Save these instructions.........................	6
Safety instructions for use.....................	7
Specifications...........................	8
Installation
Removing packing ................................	9
Removing transit bolts ..........................	9
Installation place requirements ...........	10
Connecting water supply hose............	12
Installation of drain hose .....................	14
Leveling...............................................	15
How to use washer
Operating washing machine ...............	17
Care before washing...........................	18
Washing program table.......................	19
Extra options .......................................	20
Operating data ....................................	21
Control panel.......................................	22
Options................................................	23
- Pre Wash ..........................................	23
- Favorite.............................................	23
- Steam (Wash and Softener) .............	23
- Delay.................................................	24
- Wash.................................................	24
- Temp.................................................	24
- Rinse.................................................	24
- Spin...................................................	24
Child Lock ...........................................	25
Beep On/Off ........................................	25
Tub Clean ...........................................	26
Door Lock & Detecting ........................	26
Add Item..............................................	27

Before using the Tag On function

Turning on the NFC function of the

smart phone...........................................	28
The Tag On guide..................................	29

Thank you for buying a LG Fully

Automatic Washing Machine.

Please read your owner’s manual carefully, it provides instruction on safe installation, use and maintenance. Retain it for future reference.

Record the model and serial number of your washing machine.

Model No.

Serial No.

Date of Purchase

Adding detergent

Adding detergent and fabric softener..30

The water inlet filter.............................	32
The drain pump filter ...........................	33
Dispenser drawer ................................	34
The washing drum ..............................	35
Cleaning your washer .........................	35
Cold conditions ...................................	35
Troubleshooting guide
Diagnosing problems ..........................	36
Error messages...................................	38
Using SmartDiagnosis™ .....................	39
Terms of warranty ..................	40

2

Product Features

Inverter Direct Drive system

The advanced Brushless DC motor directly drives the drum without belt and pulley.

6 Motion

Washer is able to perform various drum actions or a combination of different actions depending on the wash program selected. Combined with a controlled spin speed and the ability of the drum to

rotate both left and right, the wash performance of the machine is greatly improved, giving you perfect results every time.

Tag on

This is a function that may use Diagnosis, Download Cycle, Washing Coach, One Touch Washing, etc. when you touch the Tag On logo of the washing machine by using your smartphone with NFC.

Protection against creases

With the alternating rotation of the drum, creasing is minimized.

More economical with Intelligent Wash system

Intelligent Wash System detects the size of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption.

Child Lock

The Child Lock prevents children from pressing any button to change the settings during operation.

Low noise speed control system

By sensing the amount of load and balance, it evenly distributes load to minimize the spinning noise level.

Auto Restart

Auto Restart allows the program to restart all by itself in case of power failure. It does from the stage where it stopped.

SmartDiagnosis™

Should you experience any technical difficulty with your washing machine, it has the capability of transmitting data by phone to the Customer Information Center. The call center agent records the data transmitted from your machine and uses it to analyze the issue, providing a fast and effective diagnosis.

<![if ! IE]>

<![endif]>ENGLISH

3

Important safety instructions

READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE.

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

Your Safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION.

These words mean:

DANGER

You will be killed or seriously injured if you don’t immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow instructions.

CAUTION

You may be slightly injured or cause damage to the product if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

4

Important safety instructions

■ Basic safety precautions

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

•Before installation, check exterior damages. If it has, do not install.

•Do not install or store the washer where it will be exposed to the weather.

•Do not tamper with controls.

•Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out.

•Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc.

•The appliance is not intended for use by young children or infirm persons without supervision. Do not allow children to play on, with, or inside this or any other appliance.

•Keep small animals away from the appliance.

•Do not leave the washer door open.

An open door could entice children to hang on the door or crawl inside the washer.

•Never reach into washer while it is moving. Wait until the drum has completely stopped.

•The laundry process can reduce the flame retardant of fabrics. To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.

•Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.) which may ignite or explode. Oil may remain in the tub after a whole cycle resulting in fire during drying.

So, do not load oiled clothes.

•Do not slam the washer door closed or try to force the door open when locked. This could result in damage to the washer.

•When the machine runs high temperature, the front door may be very hot. Don’t touch it.

•To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.

•When unplugging power cord, do not pull out by grasping the cord.

Otherwise, the power cord may be damaged.

•Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

<![if ! IE]>

<![endif]>ENGLISH

5

Important safety instructions

■ Basic safety precautions

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

•Before discarding an old machine unplug it. Render the plug useless. Cut off the cable directly behind the appliance to prevent misuse.

•When a product was under water, Please call service center. There is a risk of electric shock and fire.

•Appliance connected to the water mains using new hose-sets. Old hosesets should not be reused.

■ Save these instructions

GROUNDING INSTRUCTIONS

•To reduce the risk of personal injury, adhere to all industry recommended safety procedures including the use of long sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could result in property, personal injury or death.

•Do not push down the door excessively, when washer door open.

This could topple over the washer.

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.

•Do not use an adapter this will defeat the grounding plug.

•If you don’t have the proper outlet, consult an electrician.

WARNING

Improper connection of the equipment-grounding conductor can result in electric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

6

Important safety instructions

■ Safety instructions for use

To minimize the risk of fire within the inner bowl, the following should be observed:

•Items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be placed in a tumble dryer.

Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer.

The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping and so create a fire hazard. If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce, but not eliminate, the hazard.

The ‘cool down’ cycle of tumble dryers should be used to reduce the temperature of the items.

They should not be removed from the tumble dryer or piled or stacked while hot.

•Items that have been previously cleaned in, washed in, soaked in or spotted with petrol/gasoline, drycleaning solvents or other flammable or explosive substances should not be placed in a tumble dryer. Highly flammable substances commonly used in domestic environments include acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some brands), turpentine, waxes and wax removers.

•Items containing foam rubber (also known as latex foam) or similarly textured rubber like materials should not be dried in a tumble dryer on a heat setting. Foam rubber materials can, when heated, produce fire by spontaneous combustion.

•Fabric softeners or similar products should not be used during a drying cycle, to eliminate the effects of static electricity unless this practice is specifically recommended by the manufacturer of the fabric softener or product.

•Undergarments that contain metal reinforcements should not be placed in a tumble dryer.

Damage to the tumble dryer can result if metal reinforcements come loose during drying. When available a drying rack could be used for such items.

•Plastic articles such as shower caps or babies waterproof napkin covers should not be placed in a tumble dryer.

•Rubber-backed articles, clothes fitted with foam rubber pads, pillows, rubber boots and rubber-coated tennis shoes should not be placed in a tumble dryer.

<![if ! IE]>

<![endif]>ENGLISH

7

Specifications

Transit bolts

Drawer

(For detergent and fabric softener)

Drain hose

Door

Adjustable feet

■Name

■Power supply

■Size

■Weight

■Max.Watt

■Wash capacity

■Permissible water pressure

Power plug

• If the supply cord is damaged, it must be replaced by the

manufacturer or its service agents or a similarly qualified person in order to avoid a hazard.

Control panel

Drum

Drain pump filter

Drain plug

Lower cover cap

:Front loading washing machine

:220 V~, 50 Hz

:600 mm (W) 610 mm (D) 850 mm (H)

:70 kg

:2100 W (Wash)

:10.5 kg (Wash)

:100 - 1000 kPa (1.0 - 10.0 kgf / cm2)

The appearance and specifications may vary without notice to improve the quality of the unit.

■ Accessories

Inlet hose(1EA)	Elbow Bracket	Spanner
Option : Hot/Cold(2EA)	(for securing drain hose)

8

Installation

■ Removing packing

Washer

Base Packing

1. Remove the cardboard box and styrofoam packing.

2. Lift the washing machine and remove the base packing.

3. Remove the tape securing the power supply cord and drain hose.

4. Remove the inlet hose from the drum.

	NOTE
	• Keep the spanner provided for
Spanner	future use.

WARNING

•Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation ! Keep all packaging well away from children.

■Removing transit bolts

To prevent internal damage during transport, the 4 special bolts are locked. Before operating the washer, remove the bolts along with the rubber bungs. If they are not removed, it may cause heavy vibration, noise and malfunction.

1. Unscrew the 4 bolts with the spanner supplied.

2. Take out the 4 bolts along with the rubber bungs by slightly twisting the bung.

NOTE

• Keep the transit bolts for future use.

3. Close the holes with the caps supplied.

Transit bolt

<![if ! IE]>

<![endif]>ENGLISH

9

Installation

■ Installation place requirements

Washer

approx.

2cm

Location

•Level floor :

Allowable slope under entire washer is 1˚.

•Power outlet :

Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance.

•Additional Clearance :

For Wall, 10cm:rear / 2cm : right & left side

Do not place or store laundry products on top of washer at any time.

They can damage the finish or controls.

Positioning

•Install the washer on a flat hard floor.

•Make sure that air circulation around the washer is not impeded by carpets, rugs, etc.

•Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under the washer.

•If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an insulating(85x60cm) covered with aluminum foil on the side facing the cooker or stove,must be inserted between the two appliance.

•The washer must not be installed in rooms where the temperature can drop below 0°C.

•Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of a breakdown.

•With the washer installed, adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable, and a clearance of approximately 20mm is left between the top of the washer and the underside of any work-top.

•This equipment is not designed for maritime use or for use in a mobile installations such as caravans, aircraft etc.

Electrical connection

•Do not use an extension cord or double adapter.

•If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard.

•Always unplug the machine and turn off the water supply after use.

•Connect the machine to an earthed socket in accordance with current wiring regulations.

•The appliance must be positioned so that the plug is easily accessible.

•Repairs to the washing machine must only be carried out by qualified personnel.

Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service center

•Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.

•If the appliance is delivered in the winter months and temperatures are below freezing : Place the washing machine at room temperature for a few hours before putting it into operation.

10

Installation

CAUTION

CAUTION concerning the Power cord

•Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

•Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in an electric shock or fire.

•Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.

•Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

If the appliance is supplied from a cord extension set or an electrical portable outlet device, The cord extension set on electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture.

CAUTION

•The appliance is not intended for use by young children or infirm persons without supervision.

•Young children should be supervised to ensure that they do not play with appliance.

<![if ! IE]>

<![endif]>ENGLISH

11

Installation

■ Connecting water supply hose

•Water supply pressure must be between 100 kPa and 1000 kPa (1.0 - 10.0 kgf / cm2).

•Do not strip or crossthread when connecting inlet hose to the valve.

•If the water supply pressure is more than 1000 kPa, a decompression device should be installed.

•Periodically check the condition of the hose and replace the hose if necessary.

Step1 : Check rubber seal inlet hose

• Two rubber seals are supplied with the water inlet hoses.

They are used for preventing water leaks. Make sure the connection to taps is

sufficiently tight.

Hose connector

Rubber seal

Step2 : Connect hose to water tap

Type-A : Connecting Screw-type hose to tap with thread

• Screw the hose connector onto water supply tap.

Type-B : Connecting Screw-type hose to tap without thread

	Upper	1. Unscrew the adapter ring plate and the 4
	connector	adapter retaining screws.
	Rubber
	packing	2. Push the adapter onto the end of the tap
		so that the rubber seal forms a watertight
	Fixing screw	connection. Tighten the adapter ring plate
		and the 4 screws.
		3. Push the water supply hose vertically
		upwards so that the rubber packing within
	Plate	the hose can adhere completely to the
		tap and then tighten it by screwing it to
	Water supply	the right.
	hose

12

Installation

Type-C : Connecting one touch type hose to tap without thread

		1. Unscrew the adapter ring plate and
		the 4 adapter retaining screws.
	Ring plate	2. Remove the guide plate if the tap is
		too large to fit the adapter.
	Guide plate
		3. Push the adapter onto the end of
		the tap so that the rubber seal forms
		a watertight connection.
		Tighten the adapter ring plate and
		the 4 screws.
		4. Pull the connector latch plate down,
		push the inlet hose onto the adapter,
		and release the connector latch plate.
		Make sure the adapter locks into place.

		NOTE
		• After connecting inlet hose to water
		tap, turn on the water tap to flush
	Latch plate	out foreign substances (dirt, sand or
		sawdust) in the water lines. Let
		water drain into a bucket, and
		check the water temperature.

Step3: Connect hose to washer

• Make sure that there are no kinks in the hose and that they are not crushed.

When your washer has two valves.

• The Inlet hose which has red connector is for the hot water tap.

• If the washer has two valves, the energy is saved by using hot valve.

NOTE

•After completing connection, if water leaks from the hose, repeat the same steps.

Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.

Please use the horizontal tap

Horizontal tap

Extension tap

Square tap

<![if ! IE]>

<![endif]>ENGLISH

13

Installation

Installation of drain hose

	about 100 cm
	about 145 cm
<![if ! IE]> <![endif]>100 cm
<![if ! IE]> <![endif]>max.	about 105 cm

•The drain hose should not be placed higher than 100 cm above the floor. Water in the washer does not drain or drains slowly.

•Securing the drain hose correctly will protect the floor from damage due to water leakage.

•If the drain hose is too long, do not force back into the washer.

This will cause abnormal noise.

• When installing the drain hose to a sink, secure it tightly with string.

• Securing the drain hose correctly will protect the floor from damage due to water leakage.

Laundry tub
	Hose
	Retainer
	max. 100 cm
max. 100 cm	Tie strap

14

Installation

■ Leveling

1. Leveling the washing machine properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room.

NOTE

• Timber or suspended type flooring may contribute to excessive vibration and unbalance.

Raise	Lower
Lock
Nut
	Tighten all 4
	locknuts securely

2.If the floor is uneven, turn the adjustable feet as required. (do not insert pieces of wood etc. under the feet)

Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level. (use a spirit level)

•Once the washer is level, tighten the lock nuts up towards the base of the washer. All lock nuts must be tightened.

•Diagonal Check

When pushing down the edges of the washing machine top plate diagonally,

the machine should not move up and down at all (Please, check both directions). If machine rocks when pushing the machine top plate diagonally, adjust the feet again.

<![if ! IE]>

<![endif]>ENGLISH

NOTE

•If the washing machine is installed on a raised platform, it must be securely fastened in order to eliminate the risk of falling off.

15

Installation

Concrete floors

•The installation surface must be clean, dry and level.

•Install washer on a flat hard floor.

Tile floors (Slippery floors)

•Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.)

•Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.

Wooden floors (Suspended floors)

•Wooden floors are particularly susceptible to vibration.

•To prevent vibration we recommend you place rubber cups under each foot under washer at least 15mm thick, secured to at least 2 floor beams with screws.

Rubber Cup

•If possible install the washer in one of the corners of the room, where the floor is more stable.

•Fit the rubber cups to reduce vibration.

•You can obtain the rubber cups (p/no.4620ER4002B) from the LG spares dept.

NOTE

•Proper placement and leveling of the washer will ensure long, regular and reliable operation.

•The washer must be 100% horizontal and stand firmly in position.

•It must not “Seesaw” across corners under load.

•The installation surface must be clean, free from floor wax and other lubricant coatings.

•Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.

16

How to use washer

Operating washing machine

1. Sort Laundry.

(Refer to 18 page)

2. Open the door and load laundry.

3. Press the Power button.

4. Select a Program.

(Refer to 19~21 page)

Select options at this time (Refer to 23~26 page)

■ Additional Program ■ Temperature

■ Spin Speed

■ Other functions

5. Add detergent.

(Refer to 29~30 page)

6. Press the Start/Pause button.

<![if ! IE]>

<![endif]>ENGLISH

17

How to use washer

■ Care before washing

			Wash temperature
	Normal machine wash
	Permanent press		Delicate
	Hand wash		Do not wash
	Sort laundry by...
	Soiling	Wash
		temperature
	Colour		Fabric type

NOTE

1. Care Labels

Look for a care label on your clothes.

This will tell you about the fabric content of your garment and how it should be washed.

2. Sorting

To get the best results, sort clothes into loads that can be washed with the same wash cycle.

Water temperature and spin speed and different fabrics need to be washed in different ways.

Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can occur causing discolouration of white etc. If possible, do not wash heavily soiled items with lightly soiled one.

•Soil (Heavy, Normal, Light)

Separate clothes according to amount of soil.

•Color (White, Lights, Darks)

Separate white fabrics from colored fabrics.

•Lint (Lint producers, Collectors)

Wash lint producers and lint collectors separately.

3. Caring before loading

Combine large and small items in a load. Load large items first. Large items should not be more than half the total wash load. Do not wash single items.

This may cause an out-of-balance load. Add one or two similar items.

•Check all pockets to make sure that they are empty. Items such as nails, hair clip, matches, pens, coins and keys can damage both your washer and your clothes.

•Close zippers, hooks and strings to make sure that these items don’t snag on other clothes.

•Pre treat dirt and stains by brushing a little detergent dissolved in water onto stains like collars and cuffs to help lift dirt.

•Check the folds of the flexible gasket (gray) and remove any small articles.

•Check inside of the drum and remove any item from a previous wash.

•Remove any clothing or items from the flexible gasket to prevent clothing and gasket damage.

•Before the first wash, select a cycle (Cotton 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues and water from the drum that may have been left during manufacturing.

18

How to use washer

	Program	Description	Fabric type	Proper	Maximum
				Temp.	Load
	Cotton	Provides better performance by	Color fast garments (shirts,	40°C
		combining various drum motions.		(Cold to 95°C)
			nightdresses, pajamas, etc) and
		Provides optimised washing			Rating
	Cotton		soiled cotton load normally	60°C
		performance for a large amount of	(underwear).
	Large			(Cold to 60°C)
		laundry with less energy consumption.
	Easy Care	This cycle is suitable for casual shirts	Polyamide, Acrylic, Polyester.	40°C
		that do not need ironing after washing.		(Cold to 60°C)
		Enables various fabrics to be washed	Various kind of fabrics except
	Mix		special garments. (Silk/delicate,	40°C	Less than
		simultaneously.	sports wear, dark clothes, wool,	(Cold to 40°C)
					4.0 kg
			Duvet/Curtains).
	Allergy	Removes pet hair and allergens such	Cotton, underwear, pillow covers,	60°C
	Care	as house mite and pollen.	bed sheets, baby wear.
	Silent	Provides less noise and vibration and	Color fast garments (shirts,	40°C
			nightdresses, pajamas, etc) and		Less than
		saves money by using overnight
	Wash		lightly soiled white cotton	(Cold to 60°C)	5.0 kg
		electricity.
			(underwear).
	Steam	Removes wrinkles within 20mins with	Cotton mixed, Polyester mixed	No choice	3 items
	Refresh	steam	Dress shirts, blouses.
			Cotton bedding except special
	Duvet	This cycle is for large items such as	garments (delicates, wool, silk, etc.)		1 single
		bed cover, pillows, sofa covers, etc.	with filling: duvets, pillows, blankets,		size
				40°C
			sofa covers with light filling.
				(Cold to 40°C)
	Sports	This cycle is suitable for sports wear such	Coolmax, Gore-tex, fleece and
	Wear	as jogging clothes and running wear.	Sympatex.
					Less than
		If it's possible for clothes to decolourate,
			Dark garments made from cotton		3.0 kg
	Dark	please use this cycle.		20°C
	Wash	The cycle prevent decolorization.	or mixed fabrics.	(Cold to 40°C)
		(Please use detergent for colored fabrics.)
		This cycle provides fast washing time	Coloured laundry which is lightly
			soiled fast.	20°C	Less than
	Speed 14	for small loads and lightly soiled	CAUTION : Use less than 20g of
				(20°C to 40°C)	2.0 kg
		clothes.	detergent (for 2.0kg load) otherwise
			detergent may remain on the clothes.
		This cycle is for hand and machine	Wool, hand washable clothes.
	Gentle	washable delicate clothes such as		20°C	Less than
		washable wool, lingerie, dresses etc.	Delicate, easily damaged
	Care			(Cold to 30°C)	1.5 kg
		(Please use detergent for machine	laundry.
		washable woolens).
	Stain	Wash off several kinds of stain such as		40°C
		wine, juice, dirt, etc.	Cotton blended fabrics.		Less than
	Care	(Water temperature is increased step	NOT delicate clothes.	(30°C to 60°C)	3.0 kg
		by step for washing various stains.)
	Download	For downloadable cycles.
	Cycle	If you did not download any cycles, ‘Rinse+Spin’ is set.

<![if ! IE]>

<![endif]>ENGLISH

19

How to use washer

•Water Temperature: Select water temperature to suit wash cycles.

Always follow garment manufacture’s care label or instructions when washing.

NOTE

•Neutral detergent is recommended.

Extra options

Program	Turbo	Pre	Intensive	Rinse+	Rinse	Medic	Steam	Steam	Favorite	Delay
	Wash	Wash			Hold	Rinse	Wash	Softener
Cotton
Cotton Large
Easy Care
Mix
Allergy Care							*
Silent Wash
Steam Refresh							*
Duvet
Sports Wear
Dark Wash
Speed 14	*
Gentle Care
Stain Care		*

* : This option is automatically included in the cycle and can not be deleted.

20

How to use washer

Operating data

		Max RPM
Program
	F14**		F12**
Cotton	1400		1200
Cotton Large	1400		1200
Easy Care	1000		1000
Mix	1400		1200
Allergy Care	1400		1200
Silent Wash	1000		1000
Steam Refresh	-		-
Duvet	1000		1000
Sports Wear	800		800
Dark Wash	1400		1200
Speed 14	800		800
Gentle Care	800		800
Stain Care	1400		1200

<![if ! IE]>

<![endif]>ENGLISH

21

How to use washer

■ Control panel

Power Button

Start/Pause Button

LED display

SmartDiagnosis™ function is	Program Button	Options
available only for the products with
a SmartDiagnosis™ mark.

Power

•Touch and release your fingers to turn it on.

•Touch and release your fingers after 1 second to turn it off.

Program button

•Programs are available according to the laundry type.

•Lamp will light up to indicate selected program.

Start/Pause

•This Start/Pause button is used to start wash cycle or pause the wash cycle.

•If temporary stop of wash cycle is needed, touch the Start/Pause button.

LED display

•The display shows the settings, estimated time remaining, options, and status messages for your washer.

The display will remain on through the cycle.

Options

•This allows you to select an additional cycle and will light when selected.

•Use these buttons to select the desired cycle options for the selected cycle.

22

How to use washer

■ Options

Pre Wash ()

If the laundry is heavily soiled, “Pre Wash” cycle is effective.

1.Touch the Power button.

2.Select a cycle.

3.Touch the Pre Wash button.

4.Touch the Start/Pause button.

Medic Rinse ()

For best results or for cleaner rinsing.

This allows the final rinse to be heated to 40 degrees.

1. Touch the Power button.

2. Select a cycle.

3. Touch the Medic Rinse button and set time required.

4. Touch the Start/Pause button.

Favorite

Favorite program allows you to store a customized wash cycle for future use.

1. Touch the Power button.

2. Select a cycle.

3. Select the cycle.

(Washing method, number of rinses, spin speed, water temperature etc.)

4. Touch and hold Favorite program button for 3 seconds.

The Favorite program is now stored for future use.

To reuse the program, select Favorite program and touch the Start/Pause.

Steam (Wash and Softener)

Steam Wash features enhanced washing performance with low energy consumption. Steam Softener sprays steam after spinning cycle to reduce creases and makes the laundry fluffy.

1. Touch the Power button.

2.For Steam Wash option, select steam cycles. For Steam Softener option, select Cotton or Cotton Large, Mix, Easy Care.

3.Touch the Steam button once for Steam Wash. Touch the Steam button one more time (twice) for Steam Softener.

Touch the Steam button one more time (three time) for Steam Wash and Steam Softener together.

4.Touch the Start/Pause button.

Steam Wash ( )

•For heavily stained clothes, underwear or baby clothes.

•Available with the Cotton, Cotton Large,

Mix, Easy Care, Duvet, Allergy Care, Wash+Dry, Steam Refresh cycles.

•Do not use Steam Wash for easily discoloured clothes and delicates such as wool, silk.

Steam Softener ( )

•Good to make Softens and fluffs fabrics after air drying.

•Available with the Cotton, Cotton Large,

Mix, Easy Care cycles.

•Do not use Steam Softener for easily discoloured clothes and delicates such as wool, silk.

•Depending on the kind of fabrics, softening performance may be different.

<![if ! IE]>

<![endif]>ENGLISH

23

How to use washer

Delay ()

You can set a time delay so that the washing machine will start automatically and finish after a specified time interval.

NOTE

•The delay time is the time to the end of the programme, not the start. The actual running time may vary

due to water temperature, wash load and other factors.

1. Touch the Power button.

2. Select a cycle.

3. Touch the Time Delay button and set time required.

4. Touch the Start/Pause button.

Rinse ( )

•Rinse plus () :Add rinse once.

•Rinse Hold () :

The cycle is paused until start button is touched again when rinse is finished.

Wash ( )

•Turbo Wash ( ) :

Wash cycle in under 1 hour with energy and water saving. (based on half of laundry)

•Intensive () :

If the laundry is normal and heavily soiled, “Intensive” option is effective.

Temp.

•By touching the Temp. button the water temperature can be selected.

-Cold (0)

-20°C, 30°C, 40°C, 60°C, 95°C

•Water temperature can be selected according to the program.

Spin

•Spin Speed level can be selected by touching 'Spin' button repeatedly.

•Spin Only

1. Touch the Power button.

2. Touch the Spin button to select RPM.

3. Touch the Start/Pause.

NOTE

When you select "No Spin(0)", it will still rotate for a short time with low speed to drain quickly.

24

How to use washer

■ Child Lock

Select this function to lock the buttons on the control assembly to prevent tampering.

Locking the control panel

1. Touch and hold the Child Lock button for 3 seconds.

2. A beeper will sound, and ' ' will appear on the LED display.

When the child lock is set, all buttons are locked except the Power button.

NOTE

• Turning off the power will not reset the child lock function. You must deactivate child lock before you can access any other functions.

Unlocking the control panel

1. Touch and hold the Child Lock button for 3 seconds.

2. A beeper will sound and the remaining time for the current programme will reappear on the LED display.

<![if ! IE]>

<![endif]>ENGLISH

■ Beep On / Off

1. Touch the Power button.

2. Touch the Start/Pause button.

3. Touch and hold the Temp. and Rinse button simultaneously for three seconds to set Beep

function.

the Beep on/off function is set, the setting memorized even after the power is turned off.

NOTE

• If you want to turn the Beeper off, simply repeat this process.

25

How to use washer

■ Tub Clean ( )

Tub Clean is a special cycle to clean the inside of the washing machine.

A higher water level is used in this cycle at higher spin speed. Perform this cycle regularly.

1. Remove any clothing or items from the washer and close the door.

2. Open the dispenser drawer and add Anti limescale(e.g. Calgon) to the main wash compartment.

3. Close the dispenser drawer slowly.

4. Power On and then touch and hold Tub Clean button for 3 seconds. Then ' ' and tub clean pictogram will be displayed on the LED display.

5. Touch the Start/Pause button to start.

6. After the cycle is complete, leave the door open to allow the washer door opening, flexible gasket and door glass to dry.

NOTE

•Do not add any detergent to the detergent compartments.

•Excessive suds may generate and leak from the washer.

CAUTION

•If there is a child, be careful not to leave the door open for too long.

■Door Lock & Detecting

• “Door Lock” - For safety reasons, the

door will lock while machine is in use and the “Door Lock” icon will light up. You can safely open the door after the “Door Lock” icon turns off.

• While "Detecting" is shown on the display the washing machine rotates slowly and detects how much laundry is loaded in the drum.

It will take a short time.

26