LG F1203TDS5 User Manual

• W

ater supply is not adequate in area

ater supply taps are not completely open.

Water inlet hose(s) are kinked.

•

The filter of the inlet hose(s) are clogged.

• Drain hose is kinked or clogged.

• The drain filter is clogged.

• Load is too small

.

• Load is out of balance.

The appliance has an unbalance detection

and correction system. If individual heav

y

articles are loaded (ex. bath mat, both robe,

etc.), this system may stop spinning or even

interrupt the spin cycle altogether.

If the laundry is still too wet at the end of the

cycle, add smaller articles of laundry to

balance the load and repeat the spin cycle.

• Is the door opened or not

completely closed?

•

Water overfills due to the faulty water

valve.

•

Water level sensor has malfunctioned.

• Over load in motor.

Water leaks

• The washer experienced a power failure.

Check another tap in the house.

Fully open tap.

Straighten hose(s)

Check the filter of the inlet hose(s)

Clean and straighten the drain hose.

Clean the drain filter.

For more detailed information,

please refer to

Cleaning the drain pump filter

”

Add 1 or 2 similar items to help

balance the load.

Rearrange load to allow proper

spinning

Close the door completely

.

If “ ”is not released, call for service

Unplug the power plug and call for service.

Close the water tap.

Unplug the power plug.

Call for service

Call for service

Restart the cycle.

4

1

2

3

7

1 2

3 4

6

60 - 100 cm

@

N

Adjustable feet

Adjustable feet

CAUTION

The appliance is not intended for use by young children or infi rm persons without supervision.
Young Children should be supervised to ensure that they do not play with appliance.

Disposal

• When this crossed-out wheeled bin symbol is attached to a product it means the product is
covered by European Directive 2002/96/EC.

• All electrical and electronic products should be disposed of separately from municipal
waste stream via designated collection facilities appointed by the government or the local
authorities.

• The correct disposal of your old appliance will help prevent potential adverse consequences
for the environment and human health.

• For more detailed information about disposal of your old appliance, please contact your city
offi ce, waste disposal ser vice or the shop where you purchased the product.

BS Plug Safety Details (For U.K. User)

This appliance must be earthed As the colours of the wires in the mains lead of
this apparatus may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows: The green and yellow wire must be
connected to the terminal in the plug marked E or by the earth symbol or

coloured green or green and yellow. The wire coloured blue must be connected to
the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal
marked with the letter L or coloured red. If a 13 amp (BS 1363) plug is used, fi t a 13 amp BS 1362 fuse.

Owner‘s Manual

F1403TDS(1~9)
F1203TDS(1~9)

Safety instructions for use

Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the
operating instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner
always receives these operating instructions. The following warnings must be strictly obser ved for safety rea­sons. They must be read before installing the appliance and putting it into operation.

• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only
with cold drinking water and only for washing textiles with washing detergents designed for washing machines. Every
other use is improper and may lead to injuries, whereby the liability of the manufacturer will cease.

• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.

• Never modify the appliance on your own, as this is dangerous.

• This appliance is heavy. Transporting with care.

• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.

• All installation work must be carried out by a qualifi ed fi tter or technician.

• Have electrical connections done by a qualifi ed electrician.

• Never place the appliance on the power cord.

• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.

• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug

- never disconnect by pulling the power cord. Never touch the plug with wet fi ngers or hands.

• Do not overload the appliance.

• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.

• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or
parts to warp.

• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fi re.

• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.

• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized
customer service.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive
substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in
fi re or explosion.

• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain re­mover has been used then make sure that the solvent has been carefully washed out before inserting the clothes into
the appliance. Oil may remain in the tub after a whole cycle resulting in fi re during drying. So, do not load oily clothes.

• Do not operate the appliance at locations where fl ammable substances are present such as oil, benzene or highly
infl ammable gas. Such materials may cause fi re or explosion. Never use combustible detergents.

• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.

• After washing, keep the drum door open to protect the door seal.

• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of
scalding.

• Animals and children may get into the washing machine. So always check the appliance before using it.

• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.

• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.

• The product should be serviced and repaired only by the authorised customer service using original replacement
parts.

• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in
order to protect children.

• When placing on a carpeted fl oor, make sure that the opening in the socket is not blocked.

• If the appliance has been under water then contact the customer service. There is danger of electric shock and fi re.

• The cover cup of the fi lter as well as the dispenser drawer may not be opened during the operation.

• Keep all washing powder and detergents away from children. Danger of poisoning

Before use please read carefully the safety instructions!

Thank you for buying an LG fully automatic washing machine.

Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.

Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.

Remove Packaging

Requirements for installation site

Transit bolts

Electrical connection

• The appliance is fi tted with transit bolts to prevent internal
damage during transport. Be careful, heavy load!

• Packing and all transit bolts must be removed before using
the washing machine.

• When unpacking the base, be sure to remove the additional
packing support in the middle of the base packing.

Store original packing for future move.
Dispose of packing material according to local regulations.

Unscrew the 4 bolts
using the spanner
supplied.

Keep the 4 bolts and the spanner for the future use. Refi t transit bolts before transporting the appliance.

Level fl oor: Permissible fl oor gradient under entire washing machine
is 1˚ .

Power socket: Must be within 100 cm of either side of location of
washing machine. Do not overload the socket with more than one
appliance.

Additional Clearance: For wall, fl oor and door space is needed.
(10cm: rear / 2cm:right & left side). Do not place or store laundry pro­ducts on top of the washing machine at any times. They can damage
the fi nish or controls of the machine.

1. Do not use an extension cord or double adapter.

2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualifi ed person
to prevent danger.

3. Always unplug the machine and turn off the water supply after use.

4. Connect the machine to an earthed socket in accordance with current wiring regulations.

5. The appliance must be positioned so that the plug is easily accessible.

• Repairs to the washing machine must only be carried out by qualifi ed personnel. Repairs carried out by inexpe-
rienced persons may cause injury or serious malfunctioning. Contact your local service centre.

• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The electronic control unit may become unreliable at temperatures below freezing point.

• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.

• The drain hose should not be placed higher than 100 cm above the fl oor.

• Proper securing of the drain hose will protect the fl oor from damage due to any water leakage.

• If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.

• Proper level-adjustment of the washing ma­chine prevents excessive noise and vibration.
Install the appliance on a solid and level fl oor
surface, preferably in a corner of the room.

• If the fl oor is uneven, adjust feet as required.
(Do not insert pieces of wood etc. under the
feet). Make sure that all four feet are stable
and resting on the fl oor. Then check that
the appliance is perfectly level. (Use a spirit
level).

Safety instuctions for the installation

Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the
washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted fl oor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.

CAUTION about positioning the appliance

Install the washing machine on a fl at hard fl oor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.

•

Never try to correct any unevenness in the fl oor using pieces of wood, cardboard or similar materials under the washing machine.

•

If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.

•

The washing machine must not be installed in rooms where the temperature may drop below 0°C.

•

Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.

•

Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.

CAUTION about the power cord

We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance
concerned, without any additional outlets or branch circuits. Check the specifi cations of this owner‘s manual. Do not overload
wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or
cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fi re. Periodically examine the
cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular atten-
tion to plugs, wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated
device in the mains supply.

CAUTION about location and moving

This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stop-
cock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no fl oor drain (gully)
in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young
children becoming trapped inside. Packaging material (e.g. plastic fi lm, Styrofoam) can be dangerous for children. There is a risk
of suffocation! Keep all packaging well away from children.

CAUTION about the fl oor surface

• The installation surface must be clean, dry and level.

• Install washing machine on a fl at hard fl oor.

• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.

• The washing machine must be perfectly level and fi rmly in position.

• It must not “see-saw” across corners under load.

• The installation surface must be clean, free from fl oor wax and other lubricant coatings.

• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.

Name of product Front loading washing machine

Power supply 220~240 V~, 50 Hz

Size WxDxH mm: 600 x 590 x 850

Weight 63 kg

Max. Watt

2100 W (Wash) / 1100 W (Steam)

Wash capacity 8 kg

Water consumption 52 ℓ (6.5 ℓ / kg)

Permissible water pressure 1.0-10 bar (100-1000kPa)

Rattling and clanking noise Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound Heavy wash loads may produce a thumping sound. This is usually normal.
Vibrating noise Have all transit bolts and packing been removed?
Water leaks. Check and tighten hose connections. Unclog drain pipe.

Contact plumber if necessary.

Excessive suds Too much detergent or unsuitable detergent.
Washing machine does not start Power cord may not be plugged in or connection may be loose.
Washing machine won’t spin Check that the door is fi rmly shut.
Door does not open Once started, the door can not be opened for safety reasons.

Wait one or two minutes before opening the door to allow the electric
locking mechanism time to release.

Troubleshooting

Level adjustment

To prevent internal dama­ge during transport, the
special 4 bolts are locked.
If they are not removed, it
may cause heavy vibrati­on, noise and machine to
malfunction.

Installation of drain hose

Technical Specifi cation

i

i

5

Connecting water supply hose

• Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks.

• Make sure the connection to taps is tight enough.

• Periodically check the condition of the hose and replace the hose if necessary.

• Make sure that there is no kink on the hose and that it is not crushed.

Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)

Don’t strip or crossthread when connecting inlet hose to the valve.

If the water supply pressure is more than 1000kPa, a decompression
device should be installed.

If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional
type of tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting
the tap into the adaptor.

i

The hose supplied with the machine must be used. Old hoses may not be reused

Close the holes with
the caps supplied.

Remove the 4 bolts
along with the rubber
bungs by slightly
twisting the bung.

P/No. :MFL59755582

For the U.K. customer

CUSTOMER SERVICES Tel. : [phone] LGLG(5454) Fax. : [phone]

LGEUK SERVICE WEB-SITE : http://www.lge.co.uk

1

2

3

B

A

C

A B C

1 2 3 4 5

1 3

Program

Fabric Type

Water Temp.

(Option)

Cotton

Lightly soiled clothing and
small loads

40

°C

(Cold,

30°C, 60°C)

Cotton, underwear, pillow
covers, bed sheets,
baby wear

Cotton

Quick

Synthetic

Baby Care

Allergy

Care

Delicate

Quick 30

Refresh

Hand Wash

/Wool

Color fast garments (shirts,
nightdresses, pajamas...)and
lightly soiled white cotton
(underwear)

Polyamide, Acrylic, Polyester

Lightly soiled baby wear

Delicate laundry easily
damaged

“Hand wash” marked delicate
and wool laundry

Colored laundry which is lightly
soiled fast

Cotton mixed, Polyester mixed
Dress shirts, blouses

- Time Delay

- Steam Default

- Intensive

- Crease Care

- Time Delay

- Steam Wash

- Intensive

- Soak

- Pre Wash

- Crease Care

- Rinse+Spin

- Medic Rinse

- Rinse+Spin

- Medic Rinse

- Time Delay

- Intensive

- Crease Care

- Rinse+Spin

- Steam Default

60°C

(Cold, 30°C,

40°C, 95°C)

Less than 6. 0kg

Less than 4. 0kg

Less than 4. 0kg

Rating

Less than 4. 5kg

Less than 3. 0kg

Less than 2. 0kg

3 items

40°C (Cold,

30°C, 60°C)

30°C

(Cold, 40°C)

30°C

(Cold, 40°C)

40°C

(Cold, 30°C)

No Choose

60°C

(40°C, 95°C)

60°C

Maximum Load

Option

1 2 3 4 5

5

2

1 2 3 4 5

4

[F1203T DS( 1~9)] [F1403TDS(1~9)]

INSERT PL US INTO THE MAIN S SOCKET

Never touch the plug with wet hands!
Never remove the plug from t he
socket by pulling on the cord.

HA NG UP WA STE WATER HOSE

Hose elbow connect ion e.g. at tach to water tap

WATE R CONNECT ION

Turn on the water tap

CHECKING THE MACHINE

Never use a defective machine! In case of any
failure, first unplug the machine and turn off the
water

tap.

DOING LAUNDRY A ND USING M ACHINE
WITH C ARE

- empty all pockets

- remove all metal parts

- place the delicate textiles into the laundr y net

- close zippers

WATE R TREATMENT

- wi th hardness III water

- us e water softening agent

DRUM CARE

- remove ext raneous object s

- leave door open to dry the drum

- check the rubber seals regularl y

ECOLOG ICAL WASH ING

- ma ke use of the max. wa shing quant it y

- do not “pre wash” if possible

- us e short program if possible

LAUNDRY WIT H DIFFERENT AMO UNTS OF
SOILING

Sor t the laundr y

note washing instruction symbols -

Degree of soiling -

Type of textile / colour -

Fill the drum

Check t he folds of t he f lexible gasket (grey) -

and remove a ny small ar ticles, if any. .

Check inside of the drum and remove -

any lef t in items for next wash cycle. .

Remove any clothing or items on the flexible gasket -

to prevent clothing and the gasket damages .

Fill detergent

Refer to the

written information

on t he detergent's packing

Turn the machine ON

by pressing the Power button

Select a

Program

Select the

Spinning speed

Select an Option

Pre Wash / Soak / Crease Care / Rinse + Spin

Select Rinse mode

and Washing temperat ure

4 additional programs

Press Star t / Pause
to start t he washing process

Turn off tap

- Close wate r supply

- Clean the machine

- Unplug machine

Additional Steps

- Turn the machine off

- Leave door open to
allow drum to dry

Remove laundry

- Open t he door

- Remove the laundr y

W

a

it

u

n

t

i

l

w

a

s

h

i

ng

i

s

f

i

n

i

s

h

e

d

Time Delay / Steam Wash / Intensive / Medic Rinse

Main Wash

For ver y dirt y clothes f ill 1/4 of the
por tion of detergent in here and
select a prewashing programm

Sof tener

Do not exceed the MA X-Level.
Highly densed softeners are to
be diluted with some water.

Pre Wash

For normal dir ty clothes use a small
amount of detergent. Don't pre wash.
Mount the level plate to use fluid detergents.

Dry fl at

Do not bleach

Handy to bleach

Do not tumble dry

Hang to dry

Drip dry

Medium hot ironing

Hot ironing

Do not iron

Washing temperature

Do not wash

Luke warm ironing

Turn off the water
tap

Unscrew the water
inlet hose

Pull out the water
inlet filte r

Clean t he f ilter using
a ha rd bristle brush

Pull out the
dispenser drawer

Clean t he dispenser
drawer under flow­ing water

Clean inside the
recess wit h an old
toothbrush

Insert the dispenser
drawer

Cleaning the water inlet fi lter

Cleaning the dispenser drawer

Open the lower cove r
cap. Drain plug to
pull out the hose

Unplug the drain plug.
Then open t he f ilter
by t urning to the left

Remove any
ext raneous matter
from the pump filter

After clea ning, turn
the pump filter and
insert the drain plug

Time Delay

Set ting “Time Delay” determines when machine stops.

How to set “Time Delay”

- Press Power button.

- Turn the Program dia l to select the program you require.

- Press Time Delay but ton and set time required.

- Press the Start /Pause but ton.

Intensive

If the laundr y is heavily soiled “Intensive”option is ef fective.

- By selecting the Intensive option, the washing duration may be extended,
depending on the program selected.

- To use this option, press the intensive but ton once before the wash program is started.

Medic Rinse

For best results or for cleaner rinsing, select the “Medic Rinse” option.

Available in the Cotton, Cotton Quick, Synthetic, Baby Ca re, and

Allergy Care

programs.
Medic Rinse is set by default in the Baby Care program.
The respective temperature indicator will light up.

Steam Washing and Refresh cycle

Steam Wash is

- For heavily stained clot hes, underwear, or baby clothes.

- Steam Wash is available with the Cot ton, Cot ton Quick, Synt het ic, Baby Care, and Allergy Care programs.

- Refresh cycle is always Steam wash.

- Do not load delicates such as wool, silk, and easily discolored clothe s.

Program Temperature Program Temperature

Cot ton

Cold, 30°C, 40°C, 60°C, 95°C

Baby Ca re 40°C, 60°C, 95°C

Cot ton Quick C old, 30°C, 40°C, 60°C Refresh No choose

Synthetic Cold, 30°C, 40°C, 60°C Allergy Care 60°C

How to use Refresh Cycle

Spinning cycle

Temperature

Rinse

OptionsSta rt / Paus eProg ram C ycle

Powe r but ton

Drum

Dispenser
drawer

Cover cap

Control panel

Washing program table

Additional programs

Child Lock

Tub Clean

To activate:

press and hold
the Opt ion but tons
simultaneously

To deactivate:

press and hold
the Opt ion but tons
simultaneously

Change to the desired program, whilst in child lock mode:

Empty the drum
completly and close
the door

Add anti-limesc ale
(Calgon) to the main
wash compartment.
Close the disp. drawer

Power ON wit h
Then press and
hold Rinse and
Temp. button

Press the
Start/ Pause
but ton to start Tub
Clean process

After the cycle is
complete, leave the
door open to dry

Select this function to lock the buttons on the control panel and t o prevent tampering.

Press and hold
the Opt ion but tons
simultaneously

Press
Start/Pause

Select the desired
program

press
Start/Pause

TU B CL EA N is speci al cycle to clean the inside of the washing machine.
A higher water level is used in this cyle at higher spin speed. Per form thi s cyc le re gula rly.

Preparation

lightly

heavily

Tighten up the inlet
hose

Cleaning the drain pump fi lter

Close the lower
cover cap

Washing symbols

Dispenser drawer

Once you
have finished
cleaning, replace
the drawer and
run a rinse cycle
without laundry.

Cleaning and Maintenance

Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric shock .

DisplayAdditional progra ms

Steam Cycle

Note:

To use programs in the
Steam-C ycle, please pre ss
first t he “Steam Wash” button
(see additional programs).

Refresh Allergy Care Baby Care Cot ton Synt heticCot ton Quick

1

6 3 sec.

6 3 sec.

Exterior
Proper care of your washing machine can extend its ser vice life. T he
out side of the machine can be cleaned with warm water and a neutral
non-abrasive household detergent. Immediately wipe off any spillage.
Wipe with damp clot h. Avoid striking the surface wit h sharp objects. Never
hose down the machine!

Interior

Dry around the washing machine door
opening, flexible gasket and door glass.
Run washing machine through a complete
cycle using hot water. Repeat process if
necessar y.

Cleaning in general

Important: Do not use methylated spirits, solvent s or similar products.

Water Temperature: Select water temperature to suit wash cycles. Always follow garment manufact ure’s care label or instructions when washing.
Intensive: If the laundry is heavily soiled “Intensive” option is effective.

Set program at “Cotton 60°C + Steam Wash + Intensive” option for test in accordance or in conformity with IEC60456 and EN60456.

Pre Wash: If the laundr y is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available in the Cot ton, Cot ton Quick, Synthetic, and Baby Care progra m.
Crease Care: If you want to prevent creasing, select Crease Care option.
Medic Rinse: For best result s or for cleaner rinsing, you ca n choose Medic Rinse option. Medic Rinse is set by default in the Baby Care program.

6 3 sec.

By pressing the Steam Wash but ton, Ste am Function can be selected.
When Steam Function is selected, Steam wash (

ow to use washer

H

4. Medic Rinse

• For high effectiveness or more purity in rinse
operation you can choose Medic Rinse option.

3. Intensive

• If the laundry is heavily soiled “Intensive”
option is effective.

• By selecting the Intensive option, the wash
time may be extended, depending on the
program selected.

• To use this option, press the intensive button
once before the wash program is started.

) LED lights up.

Steam Washing features enhance washing performance with low
energy consumption. Refresh cycle reduces creases in clothes.

Select the Refresh
program

Load 3 items or less
and close t he door

Press the Steam Wash button repeatedly until the
required and correct number of items is displayed

Press the
Start /Pause
but ton

2 41

The Beep on/off function can be set only during the washing cycle.

To set the Beep On/Off function follow the below steps.

1. Turn on the washing machine (by pressing the Power button).

2. Press the S tart/Pause button.

3. Press and hold the Option and Rinse button simultaneously for three seconds to set Beep on/off
function.

Once the Beep on/off function is set, the setting is memorized even after Power is off.

Beep on / off

3

The wool wash cycle of t his machine has been approved by Woolmar k for the washing of machine washable Woolma rk products provided that the products are
washed according to the instructions on the garment label and t hose issued by the manufacturer of this wa shing machine M0806.

Notes

Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment care.

Warning: Keep all washing powder and detergents away from children. Danger of poisoning

2

6 3 sec.

- wash new textiles separately

- do not prewash

- pretreat dir ty spots

- pre wash