LG E2770VV User Manual

Order Number : GETEC-C1-10-215 FCC Part 15 subpart B
Test Report Number : GETEC-E3-10-111 Page 1 / 1

APPENDIX G

: USER’S MANUAL

EUT Type: LED LCD Monitor

FCC ID.: BEJE2770VV

OWNER’S MANUAL

ENGLISH

LED LCD MONITOR

Please read this manual carefully before operating
your set and retain it for future reference.

LED LCD MONITOR MODELS

E2370V
E2770V

www.lg.com

Important Precautions

This unit has been engineered and manufactured to ensure your personal safety,
however improper use may result in potential electrical shock or fire hazards. In
order to allow the proper operation of all safeguards incorporated in this display,
observe the following basic rules for its installation, use, and servicing.

On Safety

Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.

The appliance coupler is used as the disconnect device.

Please make sure the device is installed near the wall outlet to which it is
connected and that the outlet is easily accessible.

Operate the display only from a power source indicated in the specifications of this
manual or listed on the display. If you are not sure what type of power supply you
have in your home, consult with your dealer.

Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your
service technician for replacement.

As long as this unit is connected to the AC wall outlet, it is not disconnected from
the AC power source even if the unit is turned off.

Do not Open the Display:

There are no user serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.

To Avoid Personal Injury :

Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not drop an object on or apply impact to the product. Do not throw any toys
or objects on the product screen.
It can cause injury to human, problem to product and damage the display.

To Prevent Fire or Hazards:

Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
When the display is to be left unattended for an extended period of time, unplug
it from the wall outlet.
In the presence of thunder and lightning, never touch the power cord and signal
cable because it can be very dangerous. It can cause electric shock.

1

Important Precautions

On Installation

Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.

Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.

Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:

Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.

Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.

Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.

Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.

If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.

Leaving a fixed image on the screen for a long time may cause damage to the
screen and cause image burn-in. Make sure to use a screen saver on the product.
Burn-in and related problems are not covered by the warranty on this product.

Do not shock or scratch the front and sides of the screen with metallic objects.
Otherwise, it may cause damage to the screen.

Make sure the panel faces forward and hold it with both hands to move. If you
drop the product, the damaged product can cause electric shock or fire. Contact
an authorized the service center for repair.

Avoid high temperatures and humidity.

2

Important Precautions

On Cleaning

Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display

screen because over-spraying may cause electrical shock.

When cleaning the product, unplug the power cord and scrub gently with a soft

cloth to prevent scratching. Do not clean with a wet cloth or spray water or other
liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene, paint thinners or alcohol)

Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;

wipe in one direction only. Too much moisture may cause staining.

On Repacking

Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.

On Disposal (Only , Hg lamp used LCD Monitor)

The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of

your local authority.

3

Accessories

!!! Thank you for selecting LGE products !!!

Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.

Owner's Manual/Cards

15-pin D-Sub Signal Cable

Remote control

NOTE

This accessories may look different from those shown here.
User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite
cores to maintain standard compliance for the product.

Primary Cell Battery, Lithium

Power Cord

(Depending on the country)

DVI-D Signal Cable

(This feature is not available in

all countries.)

4

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.

Connecting the stand

1. Place the monitor face down on the cushion or soft cloth.

2. Assemble the Stand Base into the Stand Body in the correct direction as shown in the picture.

Stand Body

Stand Base

3. Use a Coin on the bottom of the stand base and turn screw clockwise to tighten.

Turn the screw
by using a Coin.

4. Once assembled take the monitor up carefully and face the front side.

5

Connecting the Display

Detach the monitor to the Stand Base by turning the
screw to the left.

IMPORTANT

This illustration depicts the general model of connection. Your monitor may differ from the items
shown in the picture.
Do not carry the product upside down holding only the stand base. The product may fall and get
damaged or injure your foot.

Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.

Positioning your display

Adjust the position of the panel in various ways for maximum comfort.

Tilt Range : -5˚ to 15˚

-5

IMPORTANT

It is recommended that in order to maintain an ergonomic and
comfortable viewing position, the forward tilt angle of the monitor
should not exceed 5 degrees.

Do not touch or press the screen when adjusting the angle of the monitor.

15

6

Connecting the Display

Connecting with the PC

1. Before setting up the monitor, ensure that the power to the monitor, the computer

system, and other attached devices is turned off.

2.

Connect signal input cable and power cord in order, then tighten the screw
of the signal cable.

A

Connect DVI-D(Digital signal) Cable

B

Connect D-sub(Analog signal) Cable

C

Connect HDMI Cable

NOTE

This is a simplified representation of the rear view.
This rear view represents a general model; your display may differ from the view as shown.

1

2

Wall-outlet type

Headphone/Earphone output

Connect the signal
input cable and
tighten it up by
turning in the
direction of the
arrow as shown in
the figure.

Varies according to model.

When using a D-Sub signal input cable
connector for Macintosh

Mac adapter : For Apple Macintosh use,

a separate plug adapter is needed to
change the 15 pin high density (3 row) D­sub VGA connector on the supplied cable
to a 15 pin 2 row connector.

7

AV equipment

(Set-Top Box, DVD,
Video, Video Game
Console)

* HDMI is optimized on the AV equipment.
* Not supported PC

DVI-D (This feature is not
available in all countries.)

Connecting the Display

3. Press the power button on the bottom right of the monitor to turn the power on. When

monitor power is turned on, the 'Self Image Setting Function' is executed
automatically. (Only Analog Mode)

Power Button

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display

settings.When the user connects the monitor for the first time, this function automatically adjusts
the display to optimal settings for individual input signals.
‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen
flicker or tilted screen while using the device or after changing screen resolution, press the
AUTO function button to improve resolution.

8

Remote Control Functions

Remote Control Controls

Button

Input Button

User Mode
Button

Aspect Ratio
Button

Thru Mode
Button

Super Res.
Button

PIP Button

Swap Button

Brightness
Button

Use this button to turn the display
on or off.

Use this button to select the input signal.
(D-SUB/DVI-D/HDMI1/HDMI2)

Use this button to select the User
Mode.

Use Aspect Ratio control.

Use Frame-Buffer to prevent
picture delay.

Use Super+ Resolution
control.

Use this button to select the PIP
function.

Use this button to switch between
the main screen and the PIP
screen.

To adjust the brightness.

Volume
Button

Replacing the Remote Control Battery

1. Take out the battery cap.

2. Replace the battery (CR 2032 3V) with the + side facing up.

3. Close the battery cap.
* Use a coin to open or close the battery cover.

Button

9

To adjust the volume.
(Use for the HDMI input)

To select the mute.
(Use for the HDMI input)

Control Panel Functions

INPUTINPUT

OKOK

D-SUBD-SUB

DVI-DDVI-D

Front Panel Controls

G-MODE Button

INPUT Button

(SOURCE Hot key)

Use this button to enter USER MODE, THRU MODE, SUPER+
RESOLUTION,

ASPECT RATIO or AUTO BRIGHT menus.

For more information, refer to page 15 to 20.

When two input signals at least are connected, you can
select the input signal (D-SUB/DVI-D/HDMI1/HDMI2) you
want. When only one signal is connected, it is automatically
detected. The default setting is D-Sub.

10

Control Panel Functions

MENU Button

AUTO Button

VOLUME Button

Use this button to enter or exit from the On Screen Display.

OSD LOCKED/UNLOCKED

This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.

You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message

"OSD UNLOCKED" should appear.

AUTO IMAGE ADJUSTMENT

When adjusting your display settings, always press
the AUTO button before entering the On Screen
Display(OSD). (Only Analog Mode)

This will automatically adjust your display image to
the ideal settings for the current screen resolution
size (display mode).

The best display mode is

1920 x 1080

To adjust the headphone/ earphone volume.
(Only HDMI Mode)

EXIT Button

Power Button &
Power Indicator

Exit the OSD(On Screen Display).

Use this button to turn the display on or off.

The power indicator stays red if the display is running
properly (On Mode). If the display is in Sleep Mode
(Energy Saving), the power indicator is blinking red.

11

On Screen Display (OSD) Control Adjustment

G-MODE

USER MODE

1

MODE 1MODE 1MODE 1

2

MODE 2MODE 2MODE 2

3

MODE 3MODE 3MODE 3

G-MODE

USER MODE

NORMALNORMAL MODE 1MODE 1 MODE 2MODE 2 MODE 3MODE 3

Screen Adjustment

Making adjustments to the image size, position and operating
parameters of the display is quick and easy with the On Screen
Display Control system.
A short example is given below to familiarize you with the use of the
controls. The following section is an outline of the available
adjustments and selections you can make using the OSD.

To make adjustments in the On Screen Display, follow these steps:

Press the discretionary button, then the main menu of the OSD appears.

1

(except for the power button)

To access a control, use the corresponding buttons.

2

Use the / buttons to adjust the image to the desired level.

3

Use the button to select other sub-menu items.

4

Press the EXIT Button to exit from the OSD.

12

On Screen Display(OSD) Selection and Adjustment

The following table indicates all the On Screen Display control, adjustment,
and setting menus.

D-SUB

: D-SUB(Analog signal) input

DVI-D

: DVI-D(Digital signal) input

HDMI

: HDMI signal

Main menu Sub-menu

G-MODE

USER MODE

THRU MODE

SUPER+ RESOLUTION

ASPECT RATIO

AUTO BRIGHT

Supported input

D-SUB

DVI-D

HDMI

Description

Use this menu to select the User Mode.

To prevent picture delay, frame
buffer (video memory) is not
used in this mode.

With the picture improvement
technology that minimizes the
degradation of picture quality
due to enlargement (e.g.
blurred focus and unsharp
edge), resolution is not
compromised even when
images are enlarged, thus
guaranteeing a clear image.

Use this menu to adjust the
aspect ratio of a picture
displayed on the screen.

Use this menu to adjust the
screen brightness
automatically.

INPUT

PICTURE

COLOR

D-SUB

DVI-D

HDMI 1

HDMI 2

BRIGHTNESS
CONTRAST
SHARPNESS

BLACK LEVEL

COLOR TEMP

(PRESET) (USER)

sRGB
5000K
6500K
7200K
8200K
9300K

RED
GREEN
BLUE

GAMMA

HUE
SATURATION

COLOR RESET

13

DSUB

DVI-D

HDMI

D-SUB

DVI-D

HDMI

HDMI

D-SUB

DVI-D

HDMI

HDMI

D-SUB

DVI-D
HDMI

Use this button to select the input
signal. (D-SUB/DVI-D/
HDMI1/HDMI2)

Use this menu to adjust the
screen brightness, contrast,
sharpness and offset level.

To customize the color of the
screen