LG Dryer Instruction

I

PART REPLACEMENT

LG Dryer

LOC DESCRIPTION P/No. QTY

V101 DUCT OUTLET-A 5209EL1004A t
V102 DUCT OUTLET-B 5208EL1006A 1

V103 DUCT ELBOW 5208EL1005A 1

V104 COVER PLATE 50peELe004 A 1

i

SCREW !,_TF040260'8 1

I

I

INSTRUCTIONSHEET 3858EL400 _1D 1

INSTRUCTION

V103

V101

V102

V104

BEFORE PERFORMING THIS EXHAUSt INSTALLATION, BE SURE TO DISCONNECT THE
DRYER. FROM ITS ELECTRICAL SUPPLIY. _

PROTECT _tOUR_HARD.S AND ARMS F_OM SHARP EDGES WHEN.'..WORKING INSIDE THE

CABINET. BE SURE TO WEAR GLOVES_

TOOLS_REQUIREE_ '_#2_PhillipgScr_wdriver, Duet tapir, Gloves, Long Sleeve Shirts,

.....Small flat blade screwdriver.

PREPARING EXHAUST
INSTALLATIbN' I I

1. Detacl_ ant'! remove the Bottom, right or

left side knockout as desiFed.

2. Remove the screw from i_ear of the dryer

;llqCI S; iV(r).

:3 Pull il]_t (Itv;[ OLd of I'hd chyer, (Refer Fig. l

.%, •_

REMOVE

SCREW

AND SAVE

• Electriconly ,-,.....

REMOVE DESIRED

KNOCKOUT (ONE ONLY)

<Fig. 1 >

ADDING NEW DUCT

4. Connect the new duot(A) supplied with kit.

..I .

_7trlKe sur(_ [hat the (IucI: is aligned with the
brackt_t in [lie b,'qse as shown in Fig 2.

5 ,Jse the-.,scr(;w supplied with kit :o secure

_he duct in place d]rough the bracket on
:h_..'uppli; race buse

Follow steps below for:

ADDING ELBOW AND DUCT

FOR EXHAUST TO LEFT OR
RIGHT SIDE OF CABINET

<Fig. 3>

Follow steps below for:

f-

ADDING ELBOW

FOR EXHAUST THROUGH
BOTTOM OF CABINET

.cuTDUCT (A)

+ DUCT (B)

j<? ............

_g. 4>

6. Beware of the direction of the elbow.

7. Insert 4" elbow through the rear of dryer
and connect the elbow to the dryer

internal duet as shown in Fig. 3.
W[ap duct tape aroundaoint,as_shown

and connect the duct t0 the elbow.

i _k CAUTION

{

Besurenot topuffordamagethe electrical

L_w_!res[.ns[detheflr_yer.wh_en[nse_[ng theduct.

Apply duct tape as shown Onthe joint.between •
the dryer internal duc: and the elbow•

[ A CAUTION
I Internalductjointsmustbesecuredwithtape, t

L_otherwisetheymay'separateandcauseasafetyhazard,j

ADDING COVER PLATE TO REAR OFCABINET

6. Cut the elbow as shown in Fig. 4. "

7. Insert the elbow through the rear
Iopening and connect it to the dryer

linternal duct.

8. _,pply dUCt*ta_p:e_6h_gie_j0iflt:"between

__hecJryerinteinal,du_t and elbow, as

shown below in,Fig.5:

_i _ -A CAUTION

_nt_rnalductjointsmustbesecuredwithtape_

otherwisethey,mayseparateandcauseasafetyhazard,'

TAPE

•_ DUCT

i

=]

<Fig. 5>

(SIDES AND BOTTOM EXHAUST)

9. Connect standard meLal elbows and

ducts [o complete the exhaust system

Ias shown in Fig. 6.

10. Cover back opening with a cover plate
supplied with kit. Usethe screw that was

removed from rear of dryer to secure.
Place dryer in final location.

CoverPlate

<Fig. 6>