LG AN-MR200 User Manual

OWNER’S MANUAL

MAGIC MOTION REMOTE

Please read this manual carefully before operating your set and retain it
for future reference.

AN-MR200

Remote control (AKB732955)
RF Dongle (EAT614134)

www.lg.com

2

CH

MUTE

VOL

ENTER

Home

OK

P

MUTE

Home

OK

P

ACCESSORIES

0(18

ENTER

VOL CH

MUTE

Magic Motion

Remote Control

Owner’s manual RF Dongle RF Dongle Cable Strap Velcro

and Batteries (AA)

REMOTE DESCRIPTION

Pointer (RF transmitter)

Blinks the light when operating.

Turns the TV on or off.

Home

POWER

ENTER/OK

Selects menus or options and

confirms your input.

Press this button to display the

pointer when it disappears from the

screen.

If you press the navigation button

while moving the pointer on the

screen, the pointer disappears, and

the Magic Motion remote control

works as a regular remote control.

To display the pointer again, shake

the Magic Motion remote control

from side to side within 2 minutes

after it disappeared. (If 2 minutes

have passed, press the Enter button

to display the pointer.)

Accesses the Home menu.

Navigation (up/down/left/right)

Scrolls through menus or options.

VOL(

/

+/-)

Adjusts the volume level.

CH(

P

/

∧/∨)

Scrolls through the saved program or
channels.

MUTE

Mutes all sounds.

Installing Batteries

ꔛ

Please read this manual carefully and use the TV correctly.

ꔛ

When the message “Magic motion remote control battery is low. Change the battery.”

is displayed, replace the battery.

ꔛ

To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching

and ends to the label inside the compartment, and close the battery cover. Be sure
to point the remote control at the remote control sensor on the TV.

ꔛ

To remove the batteries, perform the installation actions in reverse. Don’t mix old or used batteries

with new ones. Close cover.

3

RF DONGLE

Use LED LCD TV/LCD TV Only.
PDP Model (50/60PZ95/75/57**) don’t need this
device. PDP TV is built in.

Cable IN

Lamp

INSTALLING RF DONGLE

Image shown may differ from your TV.

1 Locate the designated Velcro attachment

location on the TV. Then tear off the
protection paper and attach the Velcro. (The
attachment location is different depending
on the TV model you own)

Velcro

3 Attach the RF Dongle to the velcro as shown

below and then turn on the TV.

*If the RF Dongle for the wireless media box is

attached, attach the RF Dongle for the Magic
Motion remote control on the below right of the
back of the TV.

*To avoid wireless interference, keep the distance

between the RF Dongle and the Wi-Fi dongle at
20 cm.

20cm

or

*Attach the RF Dongle aligning with the upper left

corner bracket.

2 Connect the RF Dongle Cable plug on the RF

Dongle to a USB1 jack on the TV.

86%

RF SPECIFICATION

The Magic Motion Remote Control
communicates with RF Dongle using a

2.4 GHz bandwidth radio frequency (RF).

ꔛ

Output: 1 dBm or lower

ꔛ

Maximum Communication Distance:

10 m (32.8 ft) in an open space

ꔛ

Bandwidth: 2.4 GHz

(2.4035 GHz - 2.4783 GHz)

ꔛ

Transfer Rate: 250 kbps

4

OKOKOK

MUTE

ENTER

ENTER

ENTER

REGISTERING

The Magic Motion Remote Control
operates by pairing with your TV.

How to register the Magic Motion
Remote Control

To register the remote control,
press the ENTER (or OK) button
on the remote control while
aiming it at your TV.

How to Re-register the Magic
Motion Remote Control after
Registration Failure

Reset the remote control by
pressing and holding both the
ENTER (or OK) and MUTE
buttons for 5 seconds. (Once the
reset is complete, the light on
the Pointer blinks.) Then repeat
the above procedure to register
the remote control.

HOW TO USE

Press ENTER (or OK) button if
there is no pointer on your TV
screen. The pointer will appear
on the screen.
If the pointer has not been used
for a certain period of time, it will
disappear.

You can move the pointer by
aiming the front of the remote
control at your TV then move it
left, right, up or down.
If the pointer does not work
properly after clicking the ENTER
(or OK) button, wait for 10
seconds then use it again.

PRECAUTIONS TO TAKE

ꔛ

Use the remote control within the
maximum communication distance (10 m,

32.8 ft). Using the remote control beyond
this distance, or with an object
obstructing it, may cause a
communication failure.

ꔛ

A communication failure may occur due to
nearby devices. Electrical devices such as
a microwave oven or wireless LAN
product may cause interference, as this
will use the same bandwidth (2.4 GHz) as
the Magic Motion Remote Control.

ꔛ

The Magic Motion Remote Control may
be damaged or may malfunction if it is
dropped or receives a heavy impact.

ꔛ

When playing a game using the Magic
Motion Remote Control, hold it securely
by wrapping its strap around your wrist
and adjusting the length with the
adjustable ring.

ꔛ

Take care not to bump into nearby
furniture or other people when using the
Magic Motion Remote Control.

ꔛ

It is recommended that your wireless
access point be located more than 1 m
(3.28 ft) away from the TV. If the AP is
installed closer than 1 m, the magic
motion remote control may not perform
as expected due to frequency
interference.