LG 55LH95QD Owner’s Manual

ENGLISH
OWNER’S MANUAL
LCD TV MODELS
4477LLHH88****** 5555LLHH88******
LCD TV
Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the TV and Media Box. Refer to the label on the back cover and quote this information. To your dealer when requiring service.
IIDD NNuummbbeerr(( ss)) :: 6543 : 47LH80YD 6544 : 55LH80YD 6547 : 55LH95QD
DVB is a registered trademark of the DVB Project
This product qualifies for ENERGY STAR in the “factory default (Home Use mode)” setting and this is the setting in which power savings will be achieved. Changing the factory default picture setting or enabling other features will increase power consumption that could exceed the limits necessary to qualify for Energy Star rating.
Media Box is not qualified for ENERGY STAR.
MEDIA BOX
MEDIA BOX MODEL
ASW1000
LED LCD TV
LED LCD TV MODEL
5555LLHH99******
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
1

ACCESSORIES

ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.
Here shown may differ from your TV.
Owner’s Manual
Remote Controls, Batteries
Power Cord
Polishing Cloth
Polishing cloth for use on
the screen.
This item is not included for all models.
* Lightly wipe any stains or
fingerprints on the surface of the set with the polishing cloth.
Do not use excessive force. This may cause scratching or dis­colouration.
Wall Mounting Bracket(Separate purchase)
AW-47LG30M
(47LH8***)
AW-55LH40M
(55LH8***, 55LH9***)
POWERPOWER
TV/RADTV/RAD
ON/OFFON/OFF
RA RATIOTIO
AV MODEV MODE
MARKMARK
FAV
Screws for stand assembly
(Refer to p.13)
x 4
Protection cover
(Refer to p.17)
(Only 47LH8***)
POWER
AV
MODE
ENERGY SAVING
P A G E
P
FAV
MARK/
MUTE
ON/OFF
123
4506
789
LIST
Q.VIEW
INPUT
MENU
RATIO
Q.MENU
RETURN
EXIT
GUIDE
INFO
OK
TV/RAD
or
OO nnllyy 4477//5555LLHH88 ******
OO nnllyy 5555 LLHH99**** **
Plug in Type Holder
(Refer to p. 15)
Protective Bracket
for Power Cord
(Refer to p. 15)
OK
x 2
Rubber supports
x 2
Use the provided rubber supports to raise the Media Box if needed.

CONTENTS

2
CONTENTS
ACCESSORIES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
PREPARATION
Front Panel Controls..................................................... 4
Back Panel Information ................................................ 7
Wireless TV Operating Principle.............................. 10
Optimal Installation Method for Media Box......... 11
Stand Installation......................................................... 13
Back Cover for Wire Arrangement.......................... 14
Detaching Stand .......................................................... 16
Kensington Security System.......................................16
Careful installation advice ..................................... 17
Swivel Stand ..................................................................17
Not Using the Desk-type Stand ...............................17
Desktop Pedestal Installation ............................... 18
Wall Mount: Horizontal Installation ........................ 18
Antenna Connection................................................... 19
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup...................................................... 20
DVD Setup.................................................................... 22
VCR Setup..................................................................... 24
Digital Audio Out Setup ........................................... 26
Other A/V Source Setup .......................................... 27
Usb Setup...................................................................... 27
PC Setup........................................................................ 28
- Screen Setup for PC Mode ...............................30
WATCHING TV / PROGRAMME CONTROL
Remote Control Key Functions ............................... 34
Turning on the TV ........................................................39
Programme Selection ................................................ 40
Volume Adjustment ................................................... 40
Quick Menu ................................................................. 41
On-Screen Menus Selection and Adjustment..... 42
Auto Programme Tuning............................................ 43
Manual Programme Tuning (In Digital Mode)..... 44
Manual Programme Tuning (In Analogue Mode) ... 45
Programme Edit ........................................................... 47
Software Update...........................................................50
Diagnostics.................................................................... 51
Selecting the Programme List .................................. 52
Favourite Programme Setup...................................... 53
Input List........................................................................ 54
Input Label .................................................................... 55
Simple manual .............................................................. 56
................................................................. 57
AV Mode........................................................................ 60
Initializing (Reset to original factory settings) .....61
TO USE A USB DEVICE
When connecting a USB device.............................. 62
Photo List ...................................................................... 63
Music List........................................................................67
Movie List........................................................................70
DivX Registration Code..............................................74
Deactivation...................................................................75
CONTENTS
3
EPG (ELECTRONIC PROGRAMME GUIDE) (IN DIGITAL MODE)
Switch on/off EPG ...................................................... 76
Select a Programme.................................................... 76
Button Function in NOW/NEXT Guide Mode ....... 76
Button Function in 8 Day Guide Mode..................77
Button Function in Date Change Mode................ 77
Button Function in Extended Description Box ..........78
Button Function in Remind Setting Mode
......................... 78
Button Function in Schedule List Mode................ 78
PICTURE CONTROL
Picture Size (Aspect Ratio) Control ...................... 79
Picture Wizard................................................................81
Energy Saving ................................................................82
Preset Picture Settings
- Picture Mode-Preset............................................ 83
Manual Picture Adjustment
- Picture Mode-User option................................. 84
Picture Improvement Technology........................... 85
Expert Picture Control............................................... 86
Picture Reset ................................................................ 90
LED Local Dimming ..................................................... 91
Power Indicator............................................................ 92
Demo Mode.................................................................. 93
Mode Setting.................................................................94
SOUND & LANGUAGE CONTROL
Auto Volume Leveler................................................... 95
Clear Voice II..................................................................96
Preset Sound Settings - Sound Mode................... 97
Sound Setting Adjustment -User Mode ................98
SRS TruSurround XT ...................................................98
Balance............................................................................99
TV Speakers On/ Off Setup ...................................100
Selecting Digital Audio Out.....................................101
Audio Reset..................................................................102
Stereo Reception (In Analogue Mode Only)......... 103
Speaker Sound Output Selection ........................ 104
Language Selection (In Digital Mode only)....... 105
TIME SETTING
Clock Setup ................................................................ 106
Auto On/ Off Time Setting......................................107
Sleep Timer Setting .................................................. 108
PARENTAL CONTROL / RATINGS
Set Password & Lock System................................. 109
Block Programme....................................................... 110
Parental Control (In Digital Mode only).............. 111
External Input Blocking..............................................112
Key Lock ....................................................................... 113
TELETEXT
Switch on/off .............................................................. 114
SIMPLE Text................................................................. 114
TOP Text....................................................................... 114
FASTEXT........................................................................115
Special Teletext Functions ....................................... 115
APPENDIX
Troubleshooting.......................................................... 116
Maintenance ............................................................... 119
RF Specifications........................................................ 119
Product Specifications............................................. 120
Open Source Software Notice............................... 121
Open Source License.................................................122
4

PREPARATION

PREPARATION

FRONT PANEL CONTROLS

Here shown may be somewhat different from your TV.
G
When the TV cannot be turned on with the remote control, press the main power button on the TV. (When the power is turned off with the main power button on the TV, it will not be turned on with the remote control).
G
Do not step on the glass stand or subject it to any impact.
It may break, causing possible injury from fragments of glass, or the TV may fall.
G
Do not drag the TV. The floor or the product may be damaged.
CAUTION
PROGRAMME
VOLUME
OK
MENU
INPUT
POWER
Main Power Switch
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to the surrounding conditions.
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates white when the TV is switched on.
SPEAKER
Do not block this area. The wireless features will not work properly if obstacles are in front of this area.
Do not expose it to high humidity and tempera­ture or dust.
NOTE
!
G
TV can be placed in standby mode in order to reduce the power consumption. And TV should be switched off using the power switch on the TV if it will not be watched for some time, as this will reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost.
Only 47/55LH8***
P
OK
MENU
INPUT
5
PREPARATION
Here shown may be somewhat different from your TV.
Main power switch
ON
OFF
SPEAKER
RReemmoottee CC oonnttrroo ll SSeennss oorr
II nn tteelllliiggeenntt SS eennssoo rr Adjusts picture according to the surrounding con­ditions.
Power/Standby Indicator
Illuminates red in standby mode. Illuminates blue when the TV is switched on.
Note: You can turn the
PP oowweerr II nn ddiicc aa ttoorr
on or
off in the OPTION menu.
Do not block this area. The wireless features will not work properly if obstacles are in front of this area.
Do not expose it to high humidity and temperature or dust.
INPUTPOWER
MENU
OK
VOLUME PROGRAMME
TV back
TV Front
Touch Button
Light the button by touching first. At this time, you can use the desired button function.
Only 55LH9***
6
PREPARATION
PREPARATION
MEDIA BOX
Here shown may be somewhat different from your TV.
USB IN
IN 4
TV
AV1 AV2
COM1 COM21RGB WIRELESS
2 3 4
Input Source Indicator & INPUT touch button
Select the input source by touching.
POWER touch button
Turn the Media Box on or off by touching.
Even if you turn the Media Box off, it turns on again automatically if
the TV is switched on (when connected with the media box).
USB INPUT
Used for viewing photos, watching movies and listening to MP3s.
HDMI IN
Digital Connection. Supports HD video and Digital audio.
Doesn’t support 480i and 576i.
Wireless Connection Indicator
Blinks and then turns on when connecting wirelessly.
Do not place any obstacles between the RF Receiver/Transmitter of the TV and Media Box.
Do not expose it to high humidity and temperature or dust.
* ID Label of Media Box is located at the bottom of Media Box.
7
PREPARATION
Power Cord Socket
This TV operates on an AC power. The voltage is indicated on the Specifications page(
GG
pp .. 112200
). Never attempt to
operate the TV on DC power.
HDMI IN
Digital Connection. Supports HD video and Digital audio. Doesn’t support 480i, 576i and SIMPLINK (HDMI-CEC).
USB SERVICE ONLY, SERVICE ONLY
Used for software updates.

BACK PANEL INFORMATION

Here shown may be somewhat different from your TV.
1
2
3
1
3
2
Only 47/55LH8***
IN 5
SERVICE ONLY
USB
SERVICE ONLY
8
PREPARATION
PREPARATION
Here shown may be somewhat different from your TV.
HDMI IN Input
Digital Connection. Supports HD video and Digital audio. Doesn’t support 480i,576i and SIMPLINK (HDMI-CEC).
USB IN SERVICE ONLY, RS-232C IN SERVICE ONLY
Used for software updates.
Power Cord Socket
This TV operates on an AC power. The voltage is indi­cated on the Specifications page(
GG
pp .. 112200
). Never
attempt to operate the TV on DC power.
1
2
3
3
2 1
Only 55LH9***
RS-232C IN
SERVICE ONLY
USB IN
SERVICE ONLY
IN 5
9
PREPARATION
Main power switch
If you cannot turn the Media Box on with the remote control, turn the power on using the Main power switch and then switch the TV on with POWER button on the remote control.
If you turned the Media Box off using the Main power switch, you cannot turn it on with the remote control.
Component Input
Connect a component video/audio device to these jacks.
Audio/Video Input
Connect audio/video output from an external device to these jacks.
Power Cord Socket
This Media Box operates on an AC power. The voltage is indicated on the Specifications page(
GG
pp .. 112200
). Never attempt to operate the Media
Box on DC power.
RS-232C IN (SERVICE ONLY) PORT
Used for software updates.
HDMI/DVI IN Input
Connect a HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.
RGB IN (PC) Input
Connect the output from a PC.
AUDIO IN (RGB/DVI) Input
Connect the audio from a PC or DTV.
SERVICE ONLY PORT
Used for software updates.
OPTICAL DIGITAL AUDIO OUT
Connect digital audio to various types of equip-
ment. Connect to a Digital Audio Component. Use an Optical audio cable.
Antenna Input
Connect RF antenna to this jack.
1
2
3
4
5
6
7
8
9
10
1
2
1
2
COMPONENT IN
AV IN
LYPB PR R
VIDEO
AUDIO
L/MONO
R
213
/DVI IN
RGB IN (PC)
AUDIO IN
(RGB/DVI)
SERVICE ONLY
ANTENNA IN
RS-232C IN
(SERVICE ONLY)
OFFON
AC IN
VIDEO
AUDIO
OPTICAL DIGITAL AUDIO OUT
MEDIA BOX
Here shown may be somewhat different from your TV.
1
3
2
9
10
6
7
4
5
8
10
PREPARATION
PREPARATION

WIRELESS TV OPERATING PRINCIPLE

This product transmits 1080p HD video wirelessly.
This Wireless TV uses a 60GHz signal to transmit 1080p HD class video without a loss in quality. This type of high-frequency signal is stronger in the front than on the sides as shown in examples below.
General Wireless Instrument High-Frequency Wireless Instrument
The TV can connect to the media box from the front or the side. But as shown above, the signal is stronger in the front. Therefore, the media box must be closer to the TV when connecting from the side. It will attempt to connect from the front first by bouncing the signal off the back wall in the room. If it is unable to connect from the front, it will attempt to connect from the side. You may also face the box directly at the TV from across the room.
This setup usually provides the best connect. The front of the Media Box is in line of sight to the front of the TV.
This setup option is the most common. Bouncing the signal off the back wall works best when there are lim­ited obstacles blocking the signal.
Passing the signal through solid objects will degrade it. You may get a degraded or lost signal when placing the Media Box in an enclosure.
11
PREPARATION

OPTIMAL INSTALLATION METHOD FOR MEDIA BOX

If you install TV and Media Box toward the same direction like a picture, you can watch wireless TV with an optimal picture quality.
This is a recommended installation type for good wireless connection.
Please install making the number of signal strength indication to be more than three as you move Media Box as below.
Rubber supports (accessories)
Use the provided rubber supports to raise the Media Box if needed.
47/55LH80
55LH95
To check a signal strength, press the INFO button on the remote control.
CNN
DOLBY DIGITAL
Brief Info Title Test..
Sat, Feb 21, 2009 10:10 AM 11:40 AM
10:40 AM
Multilingual CaptionD 1080i TV-PG D L S V
CC
Wireless Signal
DTV
70
DOLBY DIGITAL HD
7 HD Digital
ITS ACADEMIC
Thu. 8 Mar. 2007 16: 00
16: 30
16: 21
Next
c
16:9
576p
Childrens SIMON REEVE returns with all new episodes of the educational and entertaining show where schools compete to win cash and prizes. WS
Poor Reception
Good Reception
Adjust the location and direction of the Media Box until you get good reception.
12
PREPARATION
PREPARATION
When you install Media Box inside of a cabinet, a wireless TV might not operate normally if the cabinet door is sealed up.
IInnssttaallllaa ttiioonn
EExxaammppll ee
RR ee ccoommmmeennddeedd IInnssttaall llaa ttiioonn
MMeetthhoodd
WWrr oonngg IInnssttaallllaattii oonn MMeetthhoodd
CCaa bbiinn eett
SSttrr uuccttuurree
PPrr oobbll ee mm
PPhheennoommee nnoonn
HHaann ddll ii nngg
MMeetthhoodd
Glass
Open type
Partially open type (An electric wave transmitting part should be exposed to the outside.)
In case that there is Media Box inside a sealed cabinet
In case that an electric wave transmitting part of Media Box is obstructed
In case that a cabinet inside consists of a metal
In case that a Media Box is installed deep inside of a cabinet
It is possible to watch wireless TV normally.
It is impossible to watch wireless TV.
Please check if an antenna of wireless con­nection intensity is more than three.
Please install Media Box outside of a cabi­net.
OPTIMAL INSTALLATION METHOD FOR MEDIA BOX
Media Box is capable of transmitting signal up to 25°
angle backwards, so adjust the location of the Media Box by moving back and forth until signal strength is in good reception.
Media Box Console
Signal path
GG
Move any other equipment or metal object placed on the same console that Media box is installed. They may interfere each other and wire­less connection may fail.
CAUTION
13
PREPARATION

STAND INSTALLATIONS

Only 47LH8***
1
2
3
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the TV as shown.
Fix the 4 screws securely using the holes in the back of the TV.
Image shown may differ from your TV When assembling the desk type stand, check whether the screws are fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt.
14
PREPARATION
PREPARATION

BACK COVER FOR WIRE ARRANGEMENT

Only 47/55LH8***
Here shown may be somewhat different from your TV.
CABLE MANAGEMENT CLIP
1
2
3
Connect the cables as necessary. To connect additional equipment, see the
External Equipment Setup section of the manual.
Open the
CC AABBLLEE MMAANNAAGGEEMMEENN TT CCLLII PP
as
shown and manage the cables.
Fit the
CC AABBLLEE MMAANNAAGGEEMMEENN TT CCLLII PP
as
shown.
NOTE
!
GG
Do not use the CABLE MANAGEMENT CLIP to lift the TV.
- If the TV is dropped, you may be injured or the TV may be damaged.
15
PREPARATION
1
2
1
2
3
PROTECTIVE BRACKET FOR
POWER CORD
PROTECTIVE BRACKET FOR
POWER CORD
Connect the cables as necessary. To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Loose the screw as shown. Then, secure the power cord with the
PROTECTIVE BRACKET and reinstall the screw again.
It will help prevent the power cable from being removed by accident.
Install the PLUG IN TYPE HOLDER and put the cables inside it.
Connect the cables as necessary. To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Loose the screw as shown. Then, secure the power cord with the
PROTECTIVE BRACKET and reinstall the screw again.
PLUG IN TYPE HOLDER
FOR DESK-TYPE STAND FOR WALL MOUNT
Only 55LH9***
16
PREPARATION
PREPARATION

KENSINGTON SECURITY SYSTEM

This feature is not available for all models.
Here shown may be somewhat different from your TV.
The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below.
For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Security System.
For further information, contact http://www.kensing- ton.com, the internet homepage of the Kensington
company. Kensington sells security systems for expen­sive electronic equipment such as notebook PCs and LCD projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a. If the TV feels cold to the touch, there may be a
small “flicker” when when it is turned on. This is normal, there is nothing wrong with TV.
b. Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the moni­tor's performance.
c. Avoid touching the LCD screen or holding your finger(s)
against it for long periods of time. Doing so may produce some temporary distortion
effects on the screen.
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Remove the screws from the TV.
Detach the stand from TV.

DETACHING STAND

Only 55LH9***
1
2
3
17
PREPARATION
Here shown may be somewhat different from your TV.
When installing the wall-mounted unit, use the pro­tection cover. After removing the protection paper from the pro­tection cover, adhere it to the TV as shown.

NOT USING THE DESK-TYPE STAND

(
Only 47/55LH8***)

CAREFUL INSTALLATION ADVICE

A
You should purchase necessary components to fix the TV
safety and secure to the wall on the market.
A
Position the TV close to the wall to avoid the possibility
of it falling when pushed.
A
The instructions shown below are a safer way to set up
the TV, by fixing it to the wall, avoiding the possibility of
it falling forwards if pulled. This will prevent the TV from
falling forward and causing injury. This will also prevent
the TV from damage. Ensure that children do not climb
or hang from the TV.
NOTE
!
G
When moving the TV undo the cords first.
G
Use a platform or cabinet strong and large enough to support the size and weight of the TV.
G
To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
3
1
2
Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture.
(If your TV has bolts in the eyebolts, loosen then bolts.)
* Insert the eye-bolts or TV brackets/bolts and tight-
en them securely in the upper holes.
Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.
3
Use a sturdy rope to tie the product for alignmen. It is safer to tie the rope so it becomes horizontal between the wall and the product.
2
1
2
1

SWIVEL STAND

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.
18
PREPARATION
PREPARATION
4 inches
4 inches
4 inches
4 inches

DESKTOP PEDESTAL INSTALLATION

For adequate ventilation allow a clearance of 4” (10cm) all around the TV.
A
The TV can be installed in various ways such as on a wall, or on a desktop etc.
A
The TV is designed to be mounted horizontally.
Power Supply
Circuit breaker
EARTHING
Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to earth the TV by connecting it to tele­phone wires, lightening rods or gas pipes.

WALL MOUNT: HORIZONTAL INSTALLATION

A
We recommend the use of a LG Brand wall mounting bracket when mounting the TV to a wall.
A
We recommend that you purchase a wall mounting bracket which supports VESA standard.
A
LG recommends that wall mounting be performed by a qualified professional installer.
NOTE
!
G Should Install wall mount on a solid wall perpendicular to
the floor.
G Should use a special wall mount, if you want to install it to
ceiling or slanted wall.
G The surface that wall mount is to be mounted on should
be of sufficient strength to support the weight of TV set; e.g. concrete, natural rock, brick and hollow block.
G Installing screw type and length depends on the wall
mount used. Further information, refer to the instructions included with the mount.
G LG is not liable for any accidents or damage to property or
TV due to incorrect installation:
- Where a non-compliant VESA wall mount is used.
- Incorrect fastening of screws to surface which may cause
TV to fall and cause personal injury.
- Not following the recommended Installation method.
4 inches
4 inches
4 inches
4 inches
4 inches
Model
VESA
(A *B)
Standard
Screw
Quantity
47LH8*** 55LH8***
55LH9***
200 * 200 400 * 400
400 * 400
M6 M6
M6
4 4
4
GG
Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock.
CAUTION
AA
BB
19
PREPARATION
ANTENNA IN
ANTENNA IN

ANTENNA CONNECTION

For optimum picture quality, adjust antenna direction.
An antenna cable and converter are not supplied.
To prevent damage do not connect to the mains outlet until all connections are made between the devices.
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Outdoor Antenna (VHF, UHF)
Wall Antenna Socket
RF Coaxial Wire (75 ohm)
Antenna
UHF
Signal Amplifier
VHF
In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above.
If signal needs to be split for two TVs, use an antenna signal splitter for connection.
1
2
1
2
COMPONENT IN
AV IN
LYPB PR R
VIDEO
AUDIO
L/MONO
R
213
/DVI IN
RGB IN (PC)
AUDIO IN
(RGB/DVI)
SERVICE ONLY
ANTENNA IN
RS-232C IN
(SERVICE ONLY)
OFFON
AC IN
VIDEO
AUDIO
OPTICAL DIGITAL AUDIO OUT
20

EXTERNAL EQUIPMENT SETUP

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
Image shown may differ from your TV or Media Box.

Connecting with a component cable

213
/DVI IN
RGB IN (PC)
RS-232C IN
(SERVICE ONLY)
1
2
COMPONENT IN
LYPB PR R
VIDEO
AUDIO
Y L RPB PR
VIDEO
AUD
L/MONO
1
2
Signal
480i/576i
480p/576p
720p/1080i
10 8 0 p
Component
O
O
O
O
(50Hz/60Hz)
HDMI
X
O
O
O
(24Hz/30Hz/50Hz/60Hz)
This Media Box can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below.
Connect the video outputs (Y, PB, PR
)
of the digital set
top box to the
CC OOMMPPOO NNEENN TT IINN VVIIDDEEOO
jacks on
the Media Box. Match the jack colours (Y = green, P
B
= blue, and PR = red).
Connect the audio output of the digital set-top box to the
CC OOMMPPOO NNEENNTT II NN AAUUDDII OO
jacks on the Media
Box.
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top
box.
)
Select
CC oo mm pp oo nnee nn tt 11
input source using the
IINN PPUUTT
button on the remote control. If connected to
CC OOMMPPOO NNEE NNTT II NN 22
, select
CC oo mm pp oo nneenn tt 22
input source.
2
3
4
1
GG
HDMI Audio Supported format : Dolby Digital, PCM
21
EXTERNAL EQUIPMENT SETUP
1
2
1
2
COMPONENT IN
AV IN
LYPB PR R
VIDEO
AUDIO
RGB IN (PC)
VIDEO
AUDIO
L/MONO
R
213
/DVI IN
AUDIO IN
(RGB/DVI)
L R
DVI OUTPUT
AUDIO

Connecting with an HDMI to DVI cable

1
2
Connect the digital set-top box to
HHDDMMII //DDVV II IINN 11
,
HHDDMMII //DD VVII IINN 22 orHHDDMMII //DD VVII IINN 33
jack on the
Media Box.
Connect the audio output of the digital set-top box to the
AAUU DDIIOO IINN ((RR GGBB // DDVV II))
jack on the Media Box.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.
)
Select
HH DDMM II 11,HH DD MMII22 orHH DDMM II 33
input source using
the
IINN PPUU TT
button on the remote control.
2
3
4
1
1
2
COMPONENT IN
LYPB PR R
VID
RG
VIDEO
AUDIO
213
/DVI IN
HDMI OUTPUT

Connecting a set-top box with an HDMI cable

1
Connect the digital set-top box to
HHDDMMII // DDVVII II NN 11
,
HHDDMMII // DDVVII II NN 22,HHDDMMII // DDVVII II NN 33
or
HHDDMMII IINN 44
jack on the Media Box or
HHDDMMII IINN 55
on the TV.
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box.
)
Select
HH DDMM II 11, HH DDMM II 22, HH DDMM II 33, HH DDMM II 44
or
HH DDMM II 55
input source using the
IINN PPUUTT
button on the remote
control.
2
3
1
GG
Check that your HDMI cable is version 1.3 or higher.
If the HDMI cables don’t support HDMI version 1.3, flicker­ing or no screen display can result. Please use the latest cables that support at least HDMI version 1.3.
NOTE
!
22
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP

DVD SETUP

Connecting with a component cable

213
/DVI IN
RGB IN (PC)
RS-232C IN
(SERVICE ONLY)
1
2
COMPONENT IN
LYPB PR R
VIDEO
AUDIO
Y L RPB PR
VIDEO
L/MON
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the Media Box
YPB PR
Video output ports
on DVD player
Y
Y
Y
Y
P
B
B-Y
Cb
Pb
P
R
R-Y
Cr
Pr
1
2
Connect the video outputs (Y, PB, PR
)
of the DVD to
the
CC OOMMPPOO NNEENN TT IINN VVIIDDEEOO
jacks on the Media
Box.
Connect the audio outputs of the DVD to the CC OOMMPPOO NNEENNTT II NN AAUUDDII OO
jacks on the Media Box.
Turn on the DVD player, insert a DVD.
Select
CC oo mm pp oo nneenn tt 11
input source using the
IINN PPUUTT
button on the remote control. If connected to
CC OOMMPPOO NNEE NNTT II NN 22
, select
CC oo mm pp oo nneenn tt 22
input source.
Refer to the DVD player's manual for operating instructions.
2
3
4
5
1
23
EXTERNAL EQUIPMENT SETUP
1
2
COMPONENT IN
LYPB PR R
VIDEO
RGB
VIDEO
AUDIO
213
/DVI IN
HDMI OUTPUT

Connecting the HDMI cable

Connect the HDMI output of the DVD to the HHDDMMII // DDVVII II NN 11,HHDDMMII // DDVVII II NN 22,HHDDMMII // DDVVII II NN 33
, or
HHDDMMII IINN 44
jack on the Media Box or
HHDDMMII II NN
55
on the TV.
Select
HH DDMM II 11, HH DDMM II 22, HH DDMM II 33, HH DDMM II 44
or
HH DDMM II 55
input source using the
IINN PPUUTT
button on the remote
control.
Refer to the DVD player's manual for operating instructions.
2
3
1
1
GG
The Media Box or TV can receive video and audio signals simultaneously when using an HDMI cable.
GG
If the DVD does not support Auto HDMI, you must set the output resolution appropriately.
GG
The TV set can process audio format of PCM or Dolby Digital, when connect the external equipment using an HDMI cable.
GG
Check that your HDMI cable is version 1.3 or higher.
If the HDMI cables don’t support HDMI version 1.3, flicker­ing or no screen display can result. Please use the latest cables that support at least HDMI version 1.3.
NOTE
!
24
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP

VCR SETUP

To avoid picture noise (interference), allow adequate distance between the VCR and Media Box.
N
AUDIO IN
(RGB/DVI)
SERVICE ONLY
OPTICAL DIGITAL
AUDIO OUT
ANTENNA IN
L R
S-VIDEO VIDEO
OUTPUT SWITCH
ANT IN
ANT OUT
AUDIO
Wall Jack
Antenna
1
2

Connecting with a RF Cable

Connect the
AANNTT OO UUTT
socket of the VCR to the
AANNTT EENNNNAA II NN
socket on the Media Box.
Connect the antenna cable to the
AANNTT II NN
socket of the VCR.
Press the
PPLLAAYY
button on the VCR and match the appropriate channel between the Media Box and
VCR for viewing.
2
3
1
25
EXTERNAL EQUIPMENT SETUP

Connecting with a RCA cable

Connect the
AAUU DD II OO/VVIIDDEE OO
jacks between Media Box and VCR. Match the jack colours (Video = yellow, Audio Left = white, and Audio Right = red)
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.
)
Select
AA VV 11
input source using the
IINN PPUUTT
button on
the remote control. If connected to
AAVV 22
input, select
AAVV 22
input source.
1
2
3
GG
If you have a mono VCR, connect the audio cable from the VCR to the
AAUU DDIIOO LL// MMOONN OO
jack of the Media Box.
NOTE
!
AUDIO IN
AV IN
VIDEO
AUDIO
L/MONO
R
L R
S-VIDEO VIDEO
AUDIO
OUTPUT
SWITCH
ANT IN
ANT OUT
1
2
LPB PR R
AUDIO
1
26
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP
GG
Do not look into the optical output port. Looking at the laser beam may damage your vision.
GG
Audio with ACP (Audio Copy Protection) function may block digital audio output.
CAUTION
V IN
UDIO IN
SERVICE ONLY
ANTENNA IN
OPTICAL DIGITAL AUDIO OUT
Connect one end of an optical cable to the Media Box port of
OOPPTT IICCAALL DDIIGGIITTAALL AAUUDDIIOO OOUUTT
.
Connect the other end of the optical cable to the digi­tal audio (Optical)input on the audio equipment.
Set the “TV Speaker option - Off ” in the AUDIO menu.(
G
pp..110000
) Refer to the external audio equipment
instruction manual for operation.
2
3
1
1
2

DIGITAL AUDIO OUT SETUP

Sending the TV’s audio signal to external audio equipment via the Digital Audio Output (Optical) port. If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of Media Box to a Home Theater (or amp).
GG
When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off.
GG
HDMI5 input source cannot be used for AUDIO OUT.
NOTE
!
27
EXTERNAL EQUIPMENT SETUP

USB SETUP

USB IN
IN 4
Memory Key
AV1 AV2
COM1 COM21RGB
2
Connect the USB device to the
UUSSBB II NN
jacks on
the Media Box.
After connecting the
UUSSBB II NN
jacks, you use the
UU SSBB
function. (
GG
pp..6622
)
2
1
1

OTHER A/V SOURCE SETUP

Connect the
AAUU DD IIOO/VVII DD EEOO
jacks between Media Box and external equipment. Match the jack colours
.
(
Video = yellow, Audio Left = white, and Audio
Right = red
)
Select
AA VV11
input source with using the
IINN PPUU TT
button on the remote control. If connected to
AAVV 22
input, select
AAVV 22
input
source.
Operate the corresponding external equipment. Refer to external equipment operating guide.
1
2
3
21
RGB IN (PC)
AUDIO IN
(RGB/DVI)
AV IN
VIDEO
AUDIO
L/MONO
R
L R
VIDEO
1
2
LPB PR R
AUDIO
SERVICE ONLY
OPTICAL DIG
AUDIO OU
Camcorder
Video Game Set
1
28
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP

Connecting with a HDMI to DVI cable

1
2
4
Connect the DVI output of the PC to the
HHDDMMII // DDVV II
II NN11, HHDDMMII //DDVV II IINN22
or
HHDDMMII //DDVV II IINN33
jack on
the Media Box.
Connect the PC audio output to the
AAUU DDIIOO II NN
((RR GGBB // DDVV II))
jack on the Media Box.
Turn on the PC and the Media Box.
Select
HH DDMM II 11,HH DDMM II 22orHH DDMM II 33
input source
using the INPUT button on the remote control.
2
3
1

PC SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the Media Box's settings.

Connecting with a D-sub 15 pin cable

AV IN
L R
VIDEO
AUDIO
1
SERVICE ONLY
AUDIO
L/MONO
R
O
RGB IN (PC)
AUDIO IN
(RGB/DVI)
RGB OUTPUT
AUDIO
1 2
4
Connect the RGB output of the PC to the
RRGG BB II NN
((PP CC))
jack on the Media Box.
Connect the PC audio output to the
AAUU DDIIOO II NN
((RR GGBB // DDVVII))
jack on the Media Box.
Turn on the PC and the Media Box.
Select
RRGGBB
input source using the INPUT button on
the remote control.
2
3
1
DVI-PC OUTPUT
AUDIO
COMPONENT IN
1
2
VIDEO
/DVI IN
LYPB PR R
23
1
AUDIO
VIDEO
L/MONO
RGB IN (PC)
AUDIO
AV IN
R
AUDIO IN
(RGB/DVI)
S
Loading...
+ 108 hidden pages