LG 32LH590U, 43LH604V, 49LH590V, 55LH630V User Manual [en,it]
OWNER’S MANUAL
Safety and Reference
LED TV*
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and retain it for future reference.
www.lg.com
*MFL69311713* P/NO : MFL69311713(1605-REV01) Printed in Korea
<![endif]>ENGLISH
Safety instructions
Please read these safety precautions carefully before using the product.
WARNING
Do not place the TV and/or remote control in the following environments:
t A location exposed to direct sunlight
t An area with high humidity such as a bathroom
tNear any heat source such as stoves and other devices that produce heat
tNear kitchen counters or humidi!ers where they can easily be exposed to steam or oil
t An area exposed to rain or wind
t Near containers of water such as vases
Otherwise, this may result in !re, electric shock, malfunction or product deformation.
Do not place the product where it might be exposed to dust. This may cause a !re hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains electric supply. This plug must remain readily attached and operable when TV is in use.
Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust o". You may be electrocuted due to excess moisture.
Make sure to connect Mains cable to compliant AC mains socket with Grounded earth pin. (Except for devices which are not grounded on earth.) Otherwise possibility you may be electrocuted or injured.
Insert power cable plug completely into wall socket otherwise if not secured completely into socket, !re ignition may break out.
Ensure the power cord does not come into contact with hot objects such as a heater. This may cause a !re or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables. Otherwise, this may result in !re or electric shock.
Bend antenna cable between inside and outside building to prevent rain from #owing in. This may cause water damaged inside the Product and could give an electric shock.
When mounting TV onto wall make sure to neatly install and isolate cabling from rear of TV as to not create possibility of electric shock / !re hazard.
2
Do not plug too many electrical devices into a single multiple electrical outlet. Otherwise, this may result in !re due to over-heating.
Do not drop the product or let it fall over when connecting external devices. Otherwise, this may result in injury or damage to the product.
Keep the anti-moisture packing material or vinyl packing out of the reach of children. Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause su"ocation. Keep it out of the reach of children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not consume them. Please seek DoctorMedical Attention immediately if child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/ cutlery/screwdriver) between power cable plug and input Wall Socket while it is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into the wall input terminal. You may be electrocuted. (Depending on model)
Do not put or store in#ammable substances near the product. There is a danger of combustion/explosion or !re due to careless handling of the in#ammable substances.
Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the product, or in#ammable objects such as paper and matches. Children must pay particular attention. Electrical shock, !re or injury can occur. If a foreign object is dropped into the product, unplug the power cord and contact the service centre.
Do not spray water on the product or scrub with an in#ammable substance (thinner or benzene). Fire or electric shock accident can occur.
Do not allow any impact, shock or any objects to fall into the unit, and do not drop anything onto the screen. You may be injured or the product can be damaged.
<![endif]>ENGLISH
3
<![endif]>ENGLISH
Never touch this product or antenna during a thunder or lighting storm. You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the windows and ventilate. It may cause a !re or a burn by a spark.
Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.
If water enters or comes into contact with TV, AC adapter or power cord please disconnect the power cord and contact service centre immediately. Otherwise, this may result in electric shock or !re.
Do not disassemble, repair or modify the product at your own discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
If any of the following occur, unplug the product immediately and contact your local service centre.
t The product has been impacted by shock t The product has been damaged
t Foreign objects have entered the product
t The product produced smoke or a strange smell This may result in !re or electric shock.
Unplug the TV from AC mains wall socket if you do not intend to use the TV for a long period of time. Accumulated dust can cause !re hazard and insulation deterioration can cause electric leakage/shock/!re.
Apparatus shall not be exposed to dripping or splashing and no objects !lled with liquids, such as vases, shall be placed on the apparatus.
Only use an authorized AC adapter and power cord approved by LG Electronics. Otherwise, this may result in !re, electric shock, malfunction or product deformation.
Never Disassemble the AC adapter or power cord. This may result in !re or electric shock.
Be careful in handling the adapter to prevent any external shocks to it. An external shock may cause damage to the adapter.
Make sure the power cord is connected securely to the power plug on the TV. (Depending on model)
4
CAUTION
Install the product where no radio wave occurs.
There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. This may cause an electric shock.
Do not install the product on places such as unstable shelves or inclined surfaces. Also avoid places where there is vibration or where the product cannot be fully supported. Otherwise, the product may fall or #ip over, which may cause injury or damage to the product.
If you install the TV on a stand, you need to take actions to prevent the product from overturning. Otherwise, the product may fall over, which may cause injury.
If you intend to mount the product to a wall, attach VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), !x it carefully so as not to drop.
We recommend that you maintain a distance of at least 2 to 7 times the diagonal screen size when watching TV. If you watch TV for a long period of time, this may cause blurred vision.
Only use the speci!ed type of battery. This could cause damage to the remote control.
Do not mix new batteries with old batteries. This may cause the batteries to overheat and leak.
Batteries should not be exposed to excessive heat. For example, keep away from direct Sunlight, open !replace and electric heaters.
Do not place non-rechargeable batteries in charging device.
Make sure there are no objects between the remote control and its sensor.
Only use the attachments / accessories speci!ed by the manufacturer.
When installing the antenna, consult with a quali!ed service technician. If not installed by a quali!ed technician, this may create a !re hazard or an electric shock hazard.
Signal from Remote Control can be interrupted due to external/internal lighting eg Sunlight, #uorescent lighting. If this occurs turn o" lighting or darken viewing area.
<![endif]>ENGLISH
5
<![endif]>ENGLISH
When connecting external devices such as video game consoles, make sure the connecting cables are long enough. Otherwise, the product may fall over, which may cause injury or damage the product.
Do not turn the product On/O" by plugging-in or unplugging the power plug to the wall outlet. (Do not use the power plug for switch.) It may cause mechanical failure or could give an electric shock.
Please follow the installation instructions below to prevent the product from overheating.
t The distance between the product and the wall should be more than 10 cm.
tDo not install the product in a place with no ventilation (e.g., on a bookshelf or in a cupboard).
t Do not install the product on a carpet or cushion.
t Make sure the air vent is not blocked by a tablecloth or curtain. Otherwise, this may result in !re.
Take care not to touch the ventilation openings when watching the TV for long periods as the ventilation openings may become hot. This does not a"ect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Prevent dust collecting on the power plug pins or outlet. This may cause a !re hazard.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it, as it may cause damage to screen.
Avoid touching the screen or holding your !nger(s) against it for long periods of time. Doing so may produce some temporary or permanent distortion/damage to screen.
When cleaning the product and its components, unplug the power !rst and wipe it with a soft cloth. Applying excessive force may cause scratches or discolouration. Do not spray with water or wipe with a wet cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax, benzene, alcohol etc., which can damage the product and its panel. Otherwise, this may result in !re, electric shock or product damage (Deformation, corrosion or breakage).
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn o" this unit by SWITCH.
6
When unplugging the cable, grab the plug and unplug it, by pulling at the plug.
Don’t pull at the cord to unplug the power cord from the power board, as this could be hazardous.
When moving the product, make sure you turn the power o" !rst. Then, unplug the power cables, antenna cables and all connecting cables. The TV set or power cord may be damaged, which may create a !re hazard or cause electric shock.
This panel is an advanced product that contains millions of pixels. You may see tiny black dots and/or brightly coloured dots (red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and does not a"ect the performance and reliability of the product.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
You may !nd di"erent brightness and color of the panel depending on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not related with the product performance, and it is not malfunction.
When moving or unpacking the product, work in pairs because the product is heavy. Otherwise, this may result in injury.
Refer all servicing to quali!ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Displaying a still image for a prolonged period of time may cause image sticking. Avoid displaying a !xed image on the TV screen for a long period of time.
Generated Sound
“Cracking”noise: A cracking noise that occurs when watching or turning o" the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product.
This generated sound does not a"ect the performance and reliability of the product.
|
|
|
|
|
|
Do not use high voltage electrical goods near the TV (e.g. electric |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
||
If the product feels cold to the touch, there may be a small“#icker” |
|||||||
mosquito-swatter). This may result in product malfunction. |
|||||||
when it is turned on. This is normal, there is nothing wrong with |
|||||||
|
|||||||
product. |
|
||||||
<![endif]>ENGLISH
7
<![endif]>ENGLISH
Preparing
NOTE
t If the TV is turned on for the !rst time after it was shipped from the factory, initialization of the TV may take a few minutes. (Depending on model)
t Image shown may di"er from your TV.
tYour TV’s OSD (On Screen Display) may di"er slightly from that shown in this manual.
t The available menus and options may di"er from the input source or product model that you are using.
t New features may be added to this TV in the future.
t The items supplied with your product may vary depending on the model.
tProduct speci!cations or contents of this manual may be changed without prior notice due to upgrade of product functions.
tFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not !t into your TV’s USB port.
|
B |
B |
|
|
< |
10 mm |
|
|
|
||
|
|
*A = |
|
A |
A |
< |
18 mm |
*B = |
t Use a certi!ed cable with the HDMI logo attached.
tIf you do not use a certi!ed HDMIcable, the screen may not display or a connection error may occur. (Recommended HDMICable Types)
-High-Speed HDMI®/TM Cable (3m or less)
-High-Speed HDMI®/TM Cable with Ethernet (3m or less)
tHow to use the ferrite core (Depending on model)
-Use the ferrite core to reduce the electromagnetic interference in the power cord. Wind the power cord on the ferrite core once.
[Wall side] |
[TV side] |
10 cm (+ / -2 cm)
tThis Smart TV is for VOD watching service, some smart functions may not be supported including web browser. (Only LH57**)
CAUTION
tDo not use any unapproved items to ensure the safety and product life span.
tAny damage or injuries caused by using unapproved items are not covered by the warranty.
t Some models have a thin !lm attached on to the screen and this must not be removed.
tWhen attaching the stand to the TV set, place the screen facing down on a cushioned table or #at surface to protect the screen
from scratches.
tMake sure that the screws are fastened completely. (If they are not fastened securely enough, the TV may tilt forward after being installed.) Do not use too much force and over tighten the screws; otherwise screw may be damaged and not tighten correctly.
Lifting and moving the TV
Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.
tIt is recommended to move the TV in the box or packing material that the TV originally came in.
t Before moving or lifting the TV, disconnect the power cord and all cables.
tWhen holding the TV, the screen should face away from you to avoid damage.
tHold the top and bottom of the TV frame !rmly. Make sure not to hold the transparent part, speaker, or speaker grill area.
8
t When transporting a large TV, there should be at least 2 people.
tWhen transporting the TV by hand, hold the TV as shown in the following illustration.
tWhen transporting the TV, do not expose the TV to jolts or excessive vibration.
tWhen transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right.
t Do not apply excessive pressure to cause #exing /bending of frame chassis as it may damage screen.
tWhen handling the TV, be careful not to damage the protruding buttons.
CAUTION
tAvoid touching the screen at all times, as this may result in damage to the screen.
tDo not move the TV by holding the cable holders, as the cable holders may break, and injuries and damage to the TV may occur.
Basic functions
Power On (Press)
Power O" (Press and hold)1
Volume Control
Programmes Control
1 All running apps will close, and any recording in progress will stop.
Adjusting the menu
When the TV is turned on, press the
button one time. You can adjust the Menu items pressing or moving the buttons.
Turns the power o".
Clears on-screen displays and returns to TV viewing.
Changes the input source.
Accesses the settings menu.
Using the button
(Depending on model)
You can simply operate the TV functions, pressing or moving the button.
NOTE
tLH57/59 series does not have a Joystick functions but has only a power On/O" button.
Mounting on a table
1 Lift and tilt the TV into its upright position on a table.
tLeave a 10 cm (minimum) space from the wall for proper ventilation.
|
10 cm |
|
cm |
10 cm |
10 |
|
|
|
10 cm |
|
10 cm |
|
|
2 Connect the power cord to a wall outlet. |
Dome Button |
Joystick Button |
CAUTION |
|
|
|
or |
|
t Do not place the TV near or on sources of heat, as this may result in |
|
|
!re or other damage. |
<![endif]>ENGLISH
9
<![endif]>ENGLISH
Securing the TV to a wall
(This feature is not available for all models.)
10 cm
10 cm
10 cm
10 cm
1Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV.
tIf there are bolts inserted at the eye-bolts position, remove the bolts !rst.
2Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear of the TV.
3Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the #at surface.
CAUTION
t Make sure that children do not climb on or hang on the TV.
NOTE
t Use a platform or cabinet that is strong and large enough to support the TV securely.
tBrackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the #oor. When you attach the TV to other building materials, please contact quali!ed personnel. LG recommends that wall mounting be performed by a quali!ed professional installer. We recommend the use
of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with cables connected. When you do not use LG’s wall mount bracket, please use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices. It is advised to connect all the cables before installing !xed wall mounts.
Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.
Separate purchase(Wall mounting bracket)
|
32/43LH57** |
49LH57** |
|
32/43LH59** |
49LH59** |
Model |
32/40/43LH60** |
49/55LH60** |
|
32/43LH61** |
49/55LH61** |
|
32/43LH63** |
49/55LH63** |
VESA (A x B) (mm) |
200 x 200 |
300 x 300 |
|
|
|
Standard screw |
M6 |
M6 |
|
|
|
Number of screws |
4 |
4 |
|
|
|
Wall mount |
LSW240B |
LSW350B |
bracket |
MSW240 |
MSW240 |
Model |
55LH57** |
|
55LH59** |
|
|
|
|
|
VESA (A x B) (mm) |
400 x 400 |
|
|
|
|
Standard screw |
M6 |
|
|
|
|
Number of screws |
4 |
|
|
|
|
Wall mount |
LSW440B |
|
bracket |
MSW240 |
|
A
B
10
CAUTION
tRemove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.
NOTE
tWhen installing the wall mounting bracket, use the adhesive label or protective cover provided. The adhesive label or protective cover will protect the opening from accumulating dust and dirt. (Only when the label or cover is provided)
Provided item |
Adhesive Label
Provided item
Adhesive label
Provided item
Protective cover
tWhen installing the wall mounting bracket, it is recommended to cover the stand hole using tape, in order to prevent the in#ux of dust and insects. (Depending on model)
| <![if ! IE]> <![endif]>ENGLISH |
Stand hole |
tWhen attaching a wall mounting bracket to the TV, insert the wall mount spacers into the TV wall mount holes to adjust the vertical angle of the TV. (Only when the item of the following form is provided)
Provided Item |
Wall mount spacer |
tDepending on the shape of the stand, use a #at tool to remove the stand cover as illustrated below. (e.g., a #at screwdriver)
(Only when the item of the following form is provided)
Flat tool |
11
Loading...