OWNER’S MANUAL
LED LCD TV
Please read this manual carefully before operating your set
and retain it for future reference.
47LS579C
55LS579C
60LS579C
P/NO : MFL67415427 (1206-REV00)
www.lg.com
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Short-circuit
Breaker
Power Supply
Short-circuit
Breaker
Power Supply
2
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak performance
of your product.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER
TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
WARNING
: This product contains chemicals
known to the State of California to cause cancer
and birth defects or other reproductive harm.
Wash hands after handling.
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet (Can differ by country).
Short-circuit
Breaker
Power Supply
Short-circuit
Breaker
Power Supply
IMPORTANT SAFETY INSTRUCTIONS
3
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
Only use attachments/accessories specified
by the manufacturer.
Use only with a cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Unplug this apparatus during lightning
storms or when unused for long periods of
time.
Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Keep the packing anti-moisture material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can
cause suffocation. Keep it out of the reach of
children.
CAUTION concerning the Power Cord
(Can differ by country):
It is recommended that appliances be
placed upon a dedicated circuit; that is, a
single outlet circuit which powers only that
appliance and has no additional outlets or
branch circuits. Check the specification page
of this owner’s manual to be certain. Do not
connect too many appliances to the same
AC power outlet as this could result in fire or
electric shock. Do not overload wall outlets.
Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power
cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could
result in electric shock or fire. Periodically
examine the cord of your appliance, and
if its appearance indicates damage or
deterioration, unplug it, discontinue use of
the appliance, and have the cord replaced
with an exact replacement part by an
authorized service. Protect the power cord
from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where
the cord exits the appliance. Do not move
the TV with the power cord plugged in. Do
not use a damaged or loose power cord. Be
sure do grasp the plug when unplugging the
power cord. Do not pull on the power cord
to unplug the TV.
ENGLISH
Do not stick metal objects or any other
conductive material into the power cord. Do
not touch the end of the power cord while it
is plugged in.
IMPORTANT SAFETY INSTRUCTIONS
4
ENGLISH
Warning
- To reduce the risk of fire or
electrical shock, do not expose this product
to rain, moisture or other liquids. Do not
touch the TV with wet hands. Do not install
this product near flammable objects such
as gasoline or candles, or expose the TV to
direct air conditioning.
Do not expose to dripping or splashing and
do not place objects filled with liquids, such
as vases, cups, etc. on or over the apparatus
(e.g. on shelves above the unit).
Grounding
(Except for devices which are not grounded.)
Ensure that you connect the earth ground
wire to prevent possible electric shock
(i.e. a TV with a three-prong grounded AC
plug must be connected to a three-prong
grounded AC outlet). If grounding methods
are not possible, have a qualified electrician
install a separate circuit breaker. Do not try to
ground the unit by connecting it to telephone
wires, lightening rods, or gas pipes.
Short-circuit
Breaker
Power Supply
As long as this unit is connected to the AC
wall outlet, it is not disconnected from the
AC power source even if the unit is turned
off.
Do not attempt to modify this product in any
way without written authorization from LG
Electronics. Unauthorized modification could
void the user’s authority to operate this
product.
ANTENNAS Outdoor antenna grounding
(Can differ by country):
If an outdoor antenna is installed, follow
the precautions below. An outdoor antenna
system should not be located in the vicinity
of overhead power lines or other electric light
or power circuits, or where it can come in
contact with such power lines or circuits as
death or serious injury can occur. Be sure the
antenna system is grounded so as to provide
some protection against voltage surges
and built-up static charges. Section 810 of
the National Electrical Code (NEC) in the
U.S.A. provides information with respect to
proper grounding of the mast and supporting
structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding
conductors, location of antenna discharge
unit, connection to grounding electrodes and
requirements for the grounding electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Antenna Lead in Wire
DISCONNECTING DEVICE FROM THE MAIN
POWER
Mains plug is the disconnecting device. The
plug must remain readily operable.
Ground Clamp
Electric Service
Equipment
Ground Clamp
NEC: National Electrical Code
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
Short-circuit
Breaker
Power Supply
IMPORTANT SAFETY INSTRUCTIONS
5
Cleaning
When cleaning, unplug the power cord and
wipe gently with a soft cloth to prevent
scratching. Do not spray water or other
liquids directly on the TV as electric shock
may occur. Do not clean with chemicals
such as alcohol, thinners or benzine.
Moving
Make sure the product is turned off,
unplugged and all cables have been
removed. It may take 2 or more people to
carry larger TVs. Do not press or put stress
on the front panel of the TV.
Ventilation
Install your TV where there is proper
ventilation. Do not install in a confined
space such as a bookcase. Do not cover the
product with cloth or other materials while
plugged. Do not install in excessively dusty
places.
If you smell smoke or other odors coming
from the TV, unplug the power cord and
contact an authorized service center.
Do not press strongly upon the panel with a
hand or a sharp object such as a nail, pencil
or pen, or make a scratch on it.
Keep the product away from direct sunlight.
Never touch this apparatus or antenna during
a thunder or lightning storm.
When mounting a TV on the wall, make sure
not to install the TV by hanging the power
and signal cables on the back of the TV.
Do not allow an impact shock or any objects
to fall into the product, and do not drop
anything onto the screen.
Dot Defect
The Plasma or LCD panel is a high
technology product with resolution of two
million to six million pixels. In a very few
cases, you could see fine dots on the screen
while you’re viewing the TV. Those dots
are deactivated pixels and do not affect the
performance and reliability of the TV.
Generated Sound
“Cracking” noise: A cracking noise that
occurs when watching or turning off the TV
is generated by plastic thermal contraction
due to temperature and humidity. This noise
is common for products where thermal
deformation is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a highspeed switching circuit, which supplies a
large amount of current to operate a product.
It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
Take care not to touch the ventilation
openings. When watching the TV for a long
period, the ventilation openings may become
hot. This does not affect the performance of
the product or cause defects in the product.
If the TV feels cold to the touch, there may
be a small “flicker” when it is turned on. This
is normal, there is nothing wrong with TV.
Some minute dot defects may be visible on
the screen, appearing as tiny red, green, or
blue spots. However, they have no adverse
effect on the TV’s performance. Avoid
touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary
distortion effects on the screen.
ENGLISH
6
The fluorescent lamp used in this product contains
a small amount of mercury. Do not dispose of this
product with general household waste. Disposal of
this product must be carried out in accordance to
the regulations of your local authority.
ENGLISH
For USA and Canada
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the
National Electric Code (U.S.A.). The code provides
guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected
to the grounding system of the building, as close
to the point of the cable entry as practical.
IMPORTANT SAFETY INSTRUCTIONS
DISPOSAL (Hg lamp only used in LCD TVs)
Preventing “Image burn” or “Burn-in” on your TV screen
If a fixed image displays on the TV screen
for a long period of time, it will be imprinted
and become a permanent disfigurement on
the screen. This is “image burn” or “burn-in”
and not covered by the warranty.
If the aspect ratio of the TV is set to 4:3 for
a long period of time, image burn may occur
on the letterboxed area of the screen.
Avoid displaying a fixed image on the TV
screen for a long period of time (2 or more
hours for LCD, 1 or more hours for the
Plasma TV) to prevent image burn.
NOTE TO CABLE/TV INSTALLER
FCC NOTICE
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and the receiver.
- Connect the equipment to an outlet on
a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/
TV technician for help.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference and (2) this device must
accept any interference received, including
interference that may cause undesired
operation of the device.
Any changes or modifications in construction
of this device which are not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified
DivX video. Visit divx.com for more information and software tools to convert your
files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to
vod.divx.com for more information on how to complete your registration.
“DivX Certified
®
“DivX
, DivX Certified® and associated logos are trademarks of Rovi Corporation
or its subsidiaries and are used under license.”
®
to play DivX® video up to HD 1080p, including premium content.”
®
device that plays
®
device must be registered
7
ENGLISH
ENG
“Covered by one or more of the following U.S. patents:
7,295,673; 7,460,668; 7,515,710; 7,519,274”
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380;
6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the Symbol
& DTS and the Symbol together are registered trademarks & DTS 2.0+Digital
Out is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights
Reserved.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
TABLE OF CONTENTS
8
TABLE OF CONTENTS
2 IMPORTANT SAFETY INSTRUCTIONS
7 LICENSES
7 OPEN SOURCE SOFTWARE NOTICE
8 TABLE OF CONTENTS
9 INSTALLATION PROCEDURE
9 ASSEMBLING AND PREPARING
9 Unpacking
11 Parts and buttons
12 Lifting and moving the TV
13 Setting up the TV
13 - Attaching the stand
14 - Mounting on a table
ENGLISH
15 - Tidying cables
16 - Mounting on a wall
17 MAKING CONNECTIONS
17 Connecting to an antenna or cable
18 Connecting to a HD receiver, DVD, or VCR
18 - HDMI Connection
19 - DVI to HDMI Connection
20 - Component Connection
21 - Composite Connection
22 Connecting to a PC
22 - HDMI Connection, DVI to HDMI Connec-
24 Connecting to an Audio System
24 - Digital Optical Audio Connection
25 Connecting to a USB
player
tion or RGB Connection
26 REMOTE CONTROL
26 Magic Remote Control Functions
27 - Registering Magic Remote Control
27 - How to use Magic Remote Control
27 - Precautions to Take when Using the
Magic Remote Control
28 WATCHING TV
28 Turning the TV on for the first time
29 USING THE USER GUIDE
30 SPECIFICATIONS
32 MAINTENANCE
32 Cleaning Your TV
32 - Screen, frame, cabinet and stand
32 - Power cord
32 TROUBLESHOOTING
NOTE
Image shown may differ from your TV.
Your TV’s OSD (On Screen Display) may
differ slightly from that shown in this
manual.
The available menus and options may differ
from the input source or product model that
you are using.
New features may be added to this TV in
the future.
ASSEMBLING AND PREPARING
INSTALLATION PROCEDURE
Open the package and make sure all the accessories are included.
1
Attach the stand to the TV set.
2
Connect an external device to the TV set.
3
Make sure the network connection is available.
4
You can use the TV network functions only when the network connection is made.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
Any damages or injuries by using unapproved items are not covered by the warranty.
In case of some model, the thin film on screen is a part of TV, So don’t take it off.
9
ENGLISH
ENG
NOTE
The items supplied with your product may vary depending on the model.
Product specifications or contents of this manual may be changed without prior notice due to
upgrade of product functions.
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39
inches) thick and 18 mm (0.7 inches) width.
Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit
into your TV's USB port.
B
A
*A
10 mm (0.39 inches)
*B
18 mm (0.7 inches)
B
A
ASSEMBLING AND PREPARING
10
ENGLISH
ENG
Magic Remote Control,
Batteries (AA)
(See p.26)
Stand Screws
8 EA, M4 x 20
(See p.13)
Power Cord
(Depending on model)
Owner’s manual Cable holder
(Depending on model)
(See p.15)
Desk-mount Screw
(Depending on model)
(See p.14)
Component video cable
(See p.20)
Wall mount inner spacers
4 EA (Depending on model)
(See p.16)
Composite video cable
(See p.20, 21)
Stand Body
(See p.13)
Stand Base
(See p.13)
Polishing cloth
(Depending on model)
Use this to remove dust
from the cabinet.
Parts and buttons
Screen
ASSEMBLING AND PREPARING
11
Speakers
OK
Touch Button Description
v / ^ Scrolls through the saved channels.
- / + Adjusts the volume level.
⊙
OK
SETTINGS Accesses the main menus, or saves your input and exits the menus.
INPUT Changes the input source.
ꔰ
/ I
Selects the highlighted menu option or confirms an input.
Turns the power on or off.
SETTINGS
INPUT
Remote control and
intelligent sensors
1
Power indicator
Touch buttons
2
ENGLISH
ENG
1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment.
2 All of the buttons are touch sensitive and can be operated through simple touch with your finger.
ASSEMBLING AND PREPARING
12
Lifting and moving the TV
When moving or lifting the TV, read the following
to prevent the TV from being scratched or
damaged and for safe transportation regardless of
its type and size.
CAUTION
Avoid touching the screen at all times, as
this may result in damage to the screen.
It is recommended to move the TV in the
box or packing material that the TV originally
came in.
Before moving or lifting the TV, disconnect
the power cord and all cables.
When holding the TV, the screen should face
away from you to avoid damage.
When transporting a large TV, there should
be at least 2 people.
When transporting the TV by hand, hold the
TV as shown in the following illustration.
When transporting the TV, do not expose the
TV to jolts or excessive vibration.
When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
ENGLISH
ENG
Hold the top and bottom of the TV frame
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
ASSEMBLING AND PREPARING
Setting up the TV
Put your TV on a pedestal stand and mount the TV on a table or wall.
Attaching the stand
If you are not mounting the TV to a wall, use the following instructions to attach the stand.
13
1
3
4 EA
M4 x 20
Stand Base
Stand Body
Front
Top View
2
CAUTION
When attaching the stand to the TV
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
ENGLISH
ENG
NOTE
Remove the stand before installing the TV
on a wall mount by performing the stand
attachment in reverse.
4 EA
M4 x 20
CAUTION
Tighten the screws firmly to prevent
the TV from tilting forward. Do not over
tighten.
ASSEMBLING AND PREPARING
14
ENGLISH
ENG
Mounting on a table
Lift and tilt the TV into its upright position on a
1
table.
- Leave a 10 cm (4 inches) (minimum) space
from the wall for proper ventilation.
10 cm
(4 inches)
10 cm
Connect the power cord to a wall outlet.
2
CAUTION
Do not place the TV near or on sources
of heat, as this may result in fire or other
damage.
10 cm
10 cm
Adjusting the angle of the TV to suit view
Swivel 20±2 degrees to the left or right and adjust
the angle of the TV to suit your view.
20 220 2
NOTE
When adjusting the angle of the TV, watch
out for your fingers.
»
Personal injury may occur if hands or fingers are
pinched. If the product is tilted too much, it may
fall, causing damage or injury.
Securing the TV to a table
(Depending on model)
Fix the TV to a table to prevent from tilting
forward, damage, and potential injury.
To secure the TV to a table, insert and tighten the
supplied screw on the rear of the stand.
WARNING
To prevent TV from falling over, the TV
should be securely attached to the floor/wall
per installation instructions. Tipping, shaking,
or rocking the TV may cause injury.
ASSEMBLING AND PREPARING
15
Securing the TV to a wall (optional)
Insert and tighten the eye-bolts, or TV brackets
1
and bolts on the back of the TV.
- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
Mount the wall brackets with the bolts to the
2
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
Connect the eye-bolts and wall brackets tightly
3
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
CAUTION
Make sure that children do not climb on or
hang on the TV.
Tidying cables
Gather and bind the cables with the cable holder.
Cable holder
CAUTION
Do not move the TV by holding the cable
holder, as the cable holders may break, and
injuries and damage to the TV may occur.
ENGLISH
ENG
NOTE
Use a platform or cabinet that is strong and
large enough to support the TV securely.
Brackets, bolts and ropes are optional. You
can obtain additional accessories from your
local dealer.
ASSEMBLING AND PREPARING
16
ENGLISH
ENG
Mounting on a wall
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the
floor. When you attach the TV to other building
materials, please contact qualified personnel.
We recommend that you use an LG brand wall
mount when mounting the TV to a wall.
10 cm
(4 inches)
10 cm
10 cm
10 cm
Make sure to use screws and wall mounts that
meet the VESA standard. Standard dimensions for
the wall mount kits are described in the following
table.
A
B
Model 47LS579C
VESA 400 x 400
Standard screw M6
Number of screws 4
Wall mount bracket
(optional)
55LS579C
60LS579C
LSW400BX
CAUTION
Disconnect the power first, and then move
or install the TV. Otherwise electric shock
may occur.
If you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorized LG wall mount and contact
the local dealer or qualified personnel.
Do not over tighten the screws as this may
cause damage to the TV and void your
warranty.
Use the screws and wall mounts that meet
the VESA standard. Any damages or injuries
by misuse or using an improper accessory
are not covered by the warranty.
NOTE
Use the screws that are listed on the VESA
standard screw specifications.
The wall mount kit includes an installation
manual and necessary parts.
The wall mount bracket is optional. You can
obtain additional accessories from your local
dealer.
The length of screws may differ depending
on the wall mount. Make sure to use the
proper length.
For more information, refer to the manual
supplied with the wall mount.
When attaching a third-party wall mounting
bracket to the TV, insert the wall mount
inner spacers into the TV wall mount holes
to move your TV in vertical angle. Please
make sure not to use the spacers for LG wall
mounting bracket.
LSW420BX
Wall Mount Inner Spacer
MAKING CONNECTIONS
17
MAKING CONNECTIONS
Connect various external devices to the TV and switch input modes to select an external device. For more
information on external device’s connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC,
gaming devices, and other external devices.
NOTE
If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable
to the TV through a DVD recorder or VCR. For more information on recording, refer to the manual
provided with the connected device.
The external device connection may differ from the model.
Connect external devices to the TV regardless of the order of the TV port.
If you connect a gaming device to the TV, use the cable supplied with the gaming device.
Refer to the external equipment’s manual for operating instructions.
Connecting to an antenna or cable
Connect an antenna, cable, or cable box to watch TV while referring to the following. The illustrations may
differ from the actual items and a RF cable is optional.
VHF Antenna
UHF Antenna
Antenna
ANTENNA / CABLE
Coaxial (75Ω)
CAUTION
Make sure not to bend the copper wire of
the RF cable.
Copper wire
Complete all connections between devices,
and then connect the power cord to the
power outlet to prevent damage to your TV.
Terminal
NOTE
Use a signal splitter to use more than 2 TVs.
Visit http://lgknowledgebase.com for more
information about the antenna and cable
connection. Search for antenna.
ENGLISH
18
Connecting to a HD receiver, DVD, or VCR player
Connect a HD receiver, DVD, or VCR player to the TV and select an appropriate input mode.
HDMI Connection
HDMI is the best way to connect a device.
Transmits the digital video and audio signals from an external device to the TV. Connect the external device
and the TV with the HDMI cable as shown in the following illustration.
ENGLISH
MAKING CONNECTIONS
NOTE
Use the latest High Speed HDMI™ Cable with CEC (Customer Electronics Control) function.
High Speed HDMI™ Cables are tested to carry an HD signal up to 1080p and higher.
Choose any HDMI input port to connect.
It does not matter which port you use.
(PC)
4
(*Not Provided)
HDMI
IN
2 3 1
(ARC)
NOTE
DTV Audio Supported Codec: MPEG, Dolby
Digital
HDMI Audio Supporeted Format: Dolby
Digital, PCM (Up to 192 KHz, 32k/44.1k/48k/
88k/96k/176k/192k) -> Not supported DTS.
DVD/ Blu-Ray / HD Cable Box / HD STB
ARC (Audio Return Channel)
When connected with a high-speed
HDMI cable, digital audio can be sent to a
compactible device without an additional
optical audio cable.
ARC is only supported on the HDMI input
1 (ARC) port. An external audio device that
supports ARC should be connected to
HDMI 1 if you wish to use ARC.
MAKING CONNECTIONS
DVI to HDMI Connection
Transmits the digital video signal from an external device to the TV. Connect the external device and the
TV with the DVI-HDMI cable as shown in the following illustration. To transmit an audio signal, connect an
audio cable.
(PC)
4
(*Not Provided)
DVI OUT
19
(RGB/HDMI-PC)
(RGB/HDMI-PC)
AUDIO
AUDIO
IN
(*Not Provided)
DVD/ Blu-Ray / HD Cable Box
AUDIO OUT
ENGLISH
MAKING CONNECTIONS
20
Component Connection
Transmits analog video and audio signals from an external device to the TV. Connect the external device
and the TV with a component cable as shown in the following illustration.
NOTE
If cables are installed incorrectly, it could case the image to display in black and white or with
distorted color.
Check to ensure each cable is matched with the corresponding color connection.
IN
VIDEO
AV
AUDIO
COMPONENT
PB Y
PR
ENGLISH
(Use the composite video cable provided.)
YELLOW
WHITE
WHITE
(*Not Provided)
L R
WHITE
GREENYELLOW
(Use the component video cable provided.)
RED
RED
GREEN
GREEN
BLUE
BLUE
RED
RED
(*Not Provided)
RED
GREEN
BLUE
RED
AUDIO
VIDEO
DVD/ Blu-Ray / HD Cable Box
MAKING CONNECTIONS
Composite Connection
Transmits analog video and audio signals from an external device to the TV. Connect the external device
and the TV with the composite cable as shown in the following illustration.
NOTE
Check to ensure each cable is matched with the corresponding color connection.
IN
VIDEO
AV
AUDIO
COMPONENT
PBY
PR
21
YELLOW
(Use the composite video cable provided.)
YELLOW
YELLOW
WHITE
WHITE
RED
RED
(*Not Provided)
YELLOW
WHITE
RED
ENGLISH
VIDEO
( )
MONO
AUDIOL R
VCR / DVD/ Blu-Ray / HD Cable Box
MAKING CONNECTIONS
22
Connecting to a PC
NOTE
It is recommended to use the HDMI connection for the best image quality.
Depending on the graphics card, DOS mode video may not work if a HDMI to DVI Cable is in use.
In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or
brightness. If noise is present, change the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
The synchronization input form for Horizontal and Vertical frequencies is separate.
Depending on the graphics card, some resolution settings may not allow the image to be positioned
on the screen properly.
HDMI Connection, DVI to HDMI Connection or RGB Connection
Choose method A, B, or C to make connection.
Method A: HDMI Connection
ENGLISH
Choose any HDMI input port to connect.
It is recommended to connect the DVI-HDMI
to HDMI IN 4.
(PC)
4
IN
2 3 1
(ARC)
HDMI
(*Not Provided)
PC
Method B: DVI to HDMI Connection
AUDIO OUT
DVI OUT
4
(PC)
IN
(RGB/HDMI-PC)
AUDIO
(RGB/HDMI-PC)
AUDIO
HDMI
2 3 1
(ARC)
4
(PC)
IN
(RGB/HDMI-PC)
(RGB/HDMI-PC)
AUDIO
AUDIO
IN
(PC)
4
MAKING CONNECTIONS
(*Not Provided)
23
(*Not Provided)
Method C: RGB Connection
AUDIO OUT
PC
DVI OUT
ENGLISH
(PC)
(PC)
RGB
RGB
(*Not Provided)
RGB OUT (PC)
(RGB/HDMI-PC)
(RGB/HDMI-PC)
AUDIO
AUDIO
(*Not Provided)
AUDIO OUT
PC
MAKING CONNECTIONS
24
Connecting to an Audio System
You may use an optional external audio system instead of the built-in speaker.
NOTE
If you use an optional external audio device instead of the built-in speaker, set the TV speaker feature
to off.
Digital Optical Audio Connection
Transmits a digital audio signal from the TV to an external device. Connect the external device and the TV
with the optical audio cable as shown in the following illustration.
NOTE
Do not look into the optical output port. Looking at the laser beam may damage your vision.
Audio with ACP (Audio Copy Protection) function may block digital audio output.
ENGLISH
Digital Audio System
OUT
OPTICAL
DIGITAL
AUDIO
(*Not Provided)
OPTICAL AUDIO IN
MAKING CONNECTIONS
Connecting to a USB
Connect a USB storage device such as a USB flash memory, external hard drive, or a USB memory card
reader to the TV and access the Smart Share menu to use various multimedia files.
NOTE
To use a USB Hub device, make sure that it is connected to the USB IN 2 USB port.
To store apps on a USB storage device, make sure that it is connected to the USB IN 3 USB Apps
port.
Some USB Hubs may not work. If a USB device connected using a USB Hub is not detected, connect
it to the USB port on the TV directly.
Choose any USB input port to connect.
It does not matter which port you use.
(*Not Provided)
USB
25
3
USB Hub USB Apps
USB IN
2
HDD IN
1
ENGLISH
REMOTE CONTROL
26
REMOTE CONTROL
Magic Remote Control Functions
When the message “Magic remote control battery is low. Change the battery.” is
displayed, replace the battery. To replace batteries, open the battery cover, replace
batteries (1.5 V AA) matching
and close the battery cover. Be sure to point the remote control at the remote control
sensor on the TV. To remove the batteries, perform the installation actions in reverse.
CAUTION
Do not mix old and new batteries, as this may damage the remote control.
Make sure to point the remote control at the remote control sensor on the TV.
Pointer (RF transmitter)
and ends to the label inside the compartment,
ENGLISH
Turns the TV on or off.
(POWER
BACK
Returns to the previous level.
Wheel (OK)
Selects menus or options and confirms
your input.
Scrolls through the saved channels.
If you press the navigation button while
moving the pointer on the screen, the
pointer disappears, and the Magic remote
control works as a regular remote control.
To display the pointer again, shake the
Magic remote control from side to side.
(User Guide)
Sees User Guide.
)
HOME
Accesses the Home menu.
Navigation buttons
Scrolls through menus or options.
VOL
Adjusts the volume level.
CH
Scrolls through the saved channels.
(MUTE)
Mutes all sounds.
MY APPS
Shows the list of Apps.
Q.MENU
Accesses the quick menu.
(up/down/left/right)
REMOTE CONTROL
27
Registering Magic Remote Control
The Magic Remote Control operates by pairing
with your TV.
Once you purchased the TV, please register the
Magic remote control as follows;
How to register the Magic Remote Control
(Wheel)
To register automatically, turn the TV
on and press the
registration is completed, the completion
message appears on the screen.
If registration fails, turn the TV off and
back on, then press the
complete registration.
Wheel (OK)
Wheel (OK)
. When
to
How to Re-register the Magic Remote Control
BACK
BACK
and
button for 5
BACK
HOME
1 Press and hold the
buttons together for 5 seconds
HOME
to reset, then register it by following
“How to register the Magic remote
control” above.
2 To re-register the Magic remote control,
press and hold the
seconds toward the TV.
How to use Magic Remote Control
1 You can move the pointer by aiming the
Pointer Receiver of the remote control
at your TV then move it left, right, up or
down.
»
If the pointer does not work properly
leave the remote control for 10 seconds
then use it again.
2 If the pointer disappears, move the
remote control slightly to left or right.
Then, it will automatically appear on the
screen.
»
If the pointer has not been used for a
certain period of time, it will disappear.
132
i
If you press
remote control, the screen appears.
1
Shows information about the current program
and screen.
Pressing this button will display number
2
keypad which you can select channel number.
You can select My Apps Menu.
3
Wheel (OK)
on the Magic
Precautions to Take when Using
the Magic Remote Control
Use the Magic remote control within the
maximum communication distance (10 m,
32.8ft). Using the remote control beyond
this distance, or with an object obstructing it,
may cause a communication failure.
A communication failure may occur due to
nearby devices. Electrical devices such as
a microwave oven or wireless LAN product
may cause interference, as these use the
same bandwidth (2.4 GHz) as the Magic
remote control.
The Magic remote control may be damaged
or may malfunction if it is dropped or
receives a heavy impact.
Take care not to bump into nearby furniture
or other people when using the Magic
remote control.
Manufacturer and installer cannot provide
service related to human safety as the
applicable wireless device has possibility of
electric wave interference.
It is recommended that an Access Point (AP)
be located more than 1 m (3.28 ft) away
from the TV. If the AP is installed closer than
1 m (3.28 ft), the Magic remote control may
not perform as expected due to frequency
interference.
ENGLISH
WATCHING TV
28
WATCHING TV
Turning the TV on for the first
time
When you turn the TV on for the first time, the
Initial setting screen appears. Select a language
and customize the basic settings.
1
2
3
ENGLISH
Connect the power cord to a power outlet.
In Standby mode, press the power button on
the remote control to turn the TV on.
The Initial setting screen appears if you turn
the TV on for the first time.
NOTE
You can also access
accessing
Follow the on-screen instructions to customize
your TV settings according to your preferences.
Language Selection*
OPTION
Initial Setting
in the main menu.
Selects a language to
display.
Using the Magic remote
control
Sets the Magic remote
contol.
by
NOTE
Select
mode puts the TV in demo mode.
If you select
settings will switch back to the default
settings of
When the basic settings are complete,
4
press
when prompted.
Home
Store
Store
(Wheel)
.
Store
, the any customized
in 5 minutes.
NOTE
If you do not complete the Initial setting,
it will appear whenever the TV turns on.
Disconnect the power cord from the
power outlet when you do not use the TV
for a long period of time.
To turn the TV off, press the power button on
5
the remote control.
Enviroment Selection
Time Zone Setting
Network Connection
Auto Tuning
Auto Energy Saving
mode Setting
Setting is completed.
Select
home environment.
Selects the time zone
and daylight saving.
(Depending on country)
Sets your network to
enable network-related
features on the TV.
Scans and saves available
channels automatically.
Selects Auto Energy
Saving mode.
Confirms the setting
options.
Home*
for the
USING THE USER GUIDE
USING THE USER GUIDE
29
User Guide allows you to more easily access the
detailed TV information.
Press
1
button to access the HOME
HOME
menu.
Select
2
User Guide
and press the
Wheel (OK)
User Guide
User Guide
CHANNEL Setting
PICTURE, SOUND Setting
OPTION
LG SMART Function
Advabced Function
Information
1
To use input device
To use Energy Saving feature
To set time options
To set TV lock options
To set language
Disabled Assistance
To set Magic Remote Control
4
1
User Guide
.
CHANNEL Setting
PICTURE, SOUND Setting
OPTION
LG SMART Function
Advabced Function
Information
OPTION > To set language
HOME Settings OPTION Language
Selects Menu Language and Audio Language displayed on the screen.
Menu
Selects a screen menu language.
Language
[In Digital Mode Only]
Audio
Selects the desired language when watching digital
Language
broadcasting containing several audio languages.
Select the language to make voice search.
Voice Search
✎ Only the voice search adopted model can support this
Language
setting.
Try Now Zoom In Close
2 3
HOME Settings OPTION Language
Selects Menu Language and Audio Language displayed on the screen.
Menu
Selects a screen menu language.
Language
[In Digital Mode Only]
Audio
Selects the desired language when watching digital
Language
broadcasting containing several audio languages.
Select the language to make voice search.
Voice Search
✎ Only the voice search adopted model can support this
Language
setting.
ENGLISH
Try Now Zoom Out Close
3
Shows the description of the selected menu.
1
You can use / to move between pages.
Moves to the selected menu directly from the
2
User Guide.
Zooms in or out the screen.
3
2 3
Shows the current channel.
1
Allows to select the category you want.
2
Allows to select the item you want.
You can use / button to move between
3
pages.
Allows to browse the description of the
4
function you want from the index.
SPECIFICATIONS
30
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
Power requirement
Television System NTSC-M, ATSC, 64 & 256 QAM
Program Coverage VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
External Antenna Impedance 75
Operating
Temperature
Environment
condition
Operating Humidity Less than 80 %
Storage Temperature -20 - 60 °C
Storage Humidity Less than 85 %
60LS579C: AC 120 V ~ 50 / 60 Hz
The others: AC 100 - 240 V ~ 50 / 60 Hz
Ω
0 - 40 °C
ENGLISH
MODELS
Dimensions
(Width x Height x
Depth)
Weight
Current Value / Power consumption 1.2 A / 120 W
Dimensions
(Width x Height x
Depth)
Weight
Current Value / Power consumption 1.5 A / 150 W
Dimensions
(Width x Height x
Depth)
Weight
Current Value / Power consumption 1.9 A / 190 W
With stand
Without stand
With stand 17.8 kg (39.2 lbs)
Without stand 15.3kg (33.7 lbs)
MODELS
With stand
Without stand
With stand 25.5 kg (56.2 lbs)
Without stand 21.9 kg (48.2 lbs)
MODELS
With stand
Without stand
With stand 32.3 kg (71.2 lbs)
Without stand 28.7 kg (63.2 lbs)
1089.0 x 720.0 x 269.0 mm
1263.0 x 822.0 x 315.0 mm
1391.0 x 889.0 x 315.0 mm
47LS579C
(47LS579C-UA)
(42.8 x 28.3 x 10.5 inch)
1089.0 x 655.0 x 35.5 mm
(42.8 x 25.7 x 1.3 inch)
55LS579C
(55LS579C-UA)
(49.7 x 32.3 x 12.4 inch)
1263.0 x 754.0 x 35.5 mm
(49.7 x 29.6 x 1.3 inch)
60LS579C
(60LS579C-UA)
(54.7 x 35.0 x 12.4 inch)
1391.0 x 821.0 x 43.2 mm
(54.7 x 32.3 x 1.7 inch)
SPECIFICATIONS
31
HDMI/DVI-DTV supported mode
Resolution
720X480
1280X720
1920X1080
Horizontal
Frequency (kHz)
31.469
31.5
44.96
45
33.72
33.75
26.97
27
33.716
33.75
67.43
67.5
Frequency (Hz)
Component port connecting information
Component ports on the
TV
Video output ports
on DVD player
Y P
Y P
Y B-Y R-Y
Y Cb Cr
Y Pb Pr
B
B
Vertical
59.94
60
59.94
60
59.94
60
23.97
24
29.976
30.00
59.94
60
Wireless LAN module(TWFM-B003D)
specification
Standard
Frequency Range
Modulation
Output Power (Typical)
Data rate
Antenna Gain (Typical)
Occupied bandwidth
P
R
Because band channel used by the country could
IEEE802.11a/b/g/n
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz
CCK / OFDM / MIMO
802.11a: 15 dBm
802.11b: 14 dBm
802.11g: 17 dBm
802.11n - 2.4GHz: 17 dBm
802.11n - 5GHz: 15 dBm
802.11a/g: 54 Mbps
802.11b: 11 Mbps
802.11n: 300 Mbps
2400 to 2483.5 MHz: -2.5 dBi
5150 to 5250 MHz: -2.2 dBi
5725 to 5850 MHz: -2.9 dBi
802.11a/b/g: HT20
802.11n: HT20/40
be different, the user can not change or adjust the
P
R
operating frequency and this product is set for the
ENGLISH
regional frequency table.
FCC ID of Wi-Fi module inside TV
FCC ID: BEJTWFM-B003D
Signal Component
480i O
480p O
720p/1080i O
1080p
(60 Hz only)
Bluetooth module (BM-LDS302) specification
Standard
Frequency Range
O
Output Power (Max.)
Data rate (Max.)
Communication
Distance
FCC ID of Bluetooth module inside TV
Bluetooth Version 3.0
2400 ~ 2483.5 MHz
10 dBm or lower
3 Mbps
Line of Open Sight
approx. 10 m
FCC ID: BEJLDS302
32
MAINTENANCE
Cleaning Your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
Screen, frame, cabinet and stand
To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
ENGLISH
MAINTENANCE / TROUBLESHOOTING
CAUTION
Make sure to turn the power off and disconnect the power cord and all other cables first.
When the TV is left unattended or unused for a long time, disconnect the power cord from the wall
outlet to prevent possible damage from lightning or power surges.
CAUTION
Do not push, rub, or hit the surface with your fingernail or a sharp object, as this may result in
scratches on the screen and image distortions.
Do not use any chemicals, such as waxes, benzene, alcohol, thinners, insecticides, air fresheners,
lubricants, as these may damage the screen’s finish and cause discoloration.
Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
Problem Solution
Cannot control the TV with the
remote control.
No image display and no sound is
produced.
The TV turns off suddenly.
Check the remote control sensor on the product and try again.
Check if there is any obstacle between the product and the remote control.
Check if the batteries are still working and properly installed (
Check if the product is turned on.
Check if the power cord is connected to a wall outlet.
Check if there is a problem in the wall outlet by connecting other products.
Check the power control settings. The power supply may be interrupted.
Check if the Auto sleep feature is activated in the Time settings.
If there is no signal while the TV is on, the TV will turn off automatically after 15
minutes of inactivity.
to , to ).
CHILD SAFETY:
It Makes A Difference How and Where
You Use Your Flat Panel Display
Congratulations on your purchase! As you enjoy your new product,
please keep these safety tips in mind:
THE ISSUE
The home theater entertainment experience is a growing trend and
larger flat panel displays are popular purchases. However, flat panel
displays are not always supported on the proper stands or installed
according to the manufacturer’s recommendations.
Flat pan el displ ays that are inappropriately situat ed on dressers,
bookcases, shelves, desks, speakers, chests or carts may fall over and
cause injury.
THIS MANUFACURER CARES!
The consumer electronics industry is committed to making home
entertainment enjoyable and safe.
TUNE INTO SAFETY
O n e si z e doe s NOT fit al l . F o l l o w t h e m a n u f a c tu r er ’s
recommendations for the safe installation and use of your flat panel
display.
Carefully read and understand all enclosed instructions for proper use
of this product.
Don’t allow children to climb on or play with furniture and television
sets.
Don’t allow place flat panel displays on furniture that can easily be
used as steps, such as a chest of drawers.
Remember th at chil dr en can become excited while wa tc hing
a program, especially on a “larger than life” flat panel display.
Care should be taken to place or install the display where it cannot be
pushed, pulled over, or knocked down.
Care should be taken to route all cords and cables connected to the
flat panel display so that they cannot be pulled or grabbed by curious
children.
WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT
YOUR FLAT PANEL DISPLAY, ALWAYS:
Use a mo unt th a t h as bee n r ecom m end e d b y t he dis play
manu f actu r e r a n d/or li s ted by an ind e pend e n t l a bora t ory
(such as UL, CSA, ETL).
Follow all instructions supp lied by the display and wall mount
manufacturers.
If you have any doubts about your ability to safely install your flat
panel display, contact your retailer about professional installation.
Make sure that the wall where you are mounting the display is
appropriate. Some wall mounts are not designed to be mounted
to wall s wit h stee l stu ds or old cind er bl ock c ons tru cti on.
If you are unsure, contact a professional installer.
A mi n i m um o f two p e o p le a r e requ i r e d fo r insta l l a t i o n .
Flat panel displays can be heavy
LG Customer Information Center
For inquires or comments, visit www.lg.com or call;
1-800-243-0000
1-888-865-3026
1-888-542-2623
USA, Consumer User
USA, Commercial User
CANADA
Register your product Online!
www.lg.com
The model and serial number of the TV is located
on the back and one side of the TV.
Record it below should you ever need service.
MODEL
SERIAL
(For 47/55LS579C)
This product qualifies for ENERGY STAR in the
“factory default (Home Use)” setting.
Changing the factory default settings or enabling
other features may increase power consumption
that could exceed the limits necessary to quality
for ENERGY STAR.
Loading...