LG 49UT672M, 43UT672M, 55UT672M User Manual

43UT672M 49UT672M 55UT672M
Hospital Grade Interactive Pro:Centric ® TVs
Commercial Mode Setup Guide
Note: Selected features shown in this guide may not be available on all models.
EXPERIENCED INSTALLER
First Use Wizard pages 17 – 19
© Copyright 2020 LG Electronics U.S.A., Inc.
Custom Master TV Setup pages 64 – 67
P/N: 206-4344 (Rev B)
For Customer Support/Service, please call:
1-888-865-3026
The latest product information and documentation is available online at:
www.lg.com/us/business
MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here:
Model No._________________ Serial No._______________
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER­SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING:
This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
POWER CORD POLARIZATION:
This product is equipped with a 3-wire grounding-type alternating current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the 3-wire grounding-type plug.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electrical Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
2
© Copyright 2020 LG Electronics U.S.A., Inc.
206-4344
IMPORTANT SAFETY INSTRUCTIONS
PORTABLE CART WARNING
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accor­dance with the manufacturer’s instructions.
8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination in order to avoid injury from tip-over.
13.
Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14. Never touch this apparatus or antenna during a thunder or
lightning storm.
15. Do not apply pressure on or scratch the TV panel during handling. Do not press against the TV panel with your hand or a sharp object such as a nail, pencil, or pen.
16. Power Cord Caution: Check the TV specifications in the Owner’s
Manual to determine power requirements.
Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as twisting, kinking, or pinching or being closed in a door or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Do not use a damaged or loose power cord. Be sure to grasp
the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
Do not stick metal objects or any other conductive material
into the power cord. Do not touch the end of the power cord while it is plugged in.
17. Overloading Do not connect too many appliances to the same AC power
outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of
these conditions could result in re or electric shock.
18. Outdoor Use/Wet Location
Warning: To reduce the risk of re or electrical
shock, do not expose this product to rain, moisture or other liquids.
Do not touch the TV with wet hands. Do not install this product
near ammable objects such as gasoline or candles or expose
the TV to direct air conditioning.
Do not expose to dripping or splashing and do not place
objects lled with liquids, such as vases, cups, etc., on or over
the apparatus (e.g., on shelves above the unit).
19. Grounding (Except for devices that are not grounded) Ensure that you
connect the earth ground wire to prevent possible electric shock (i.e., a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualied electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightning rods, or gas pipes.
20. Disconnect Device The power plug is the disconnecting device. The power plug
must remain readily accessible.
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if the unit is turned off.
206-4344
(Continued on next page)
3
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
21. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the
product, follow the precautions below.
An outdoor antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to provide
some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code (NEC) in the U.S.A.
provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Antenna Grounding According to NEC, ANSI/NFPA 70
Ground Clamp
Electric Service
Equipment
Antenna Lead in Wire
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductor (NEC Section 810-21)
Ground Clamps
Power Service Grounding Electrode System (NEC Art 250, Part H)
22. Cleaning When cleaning, unplug the power cord and wipe gently with
a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
23. Transporting Product Make sure the TV is turned off and unplugged and that all
cables have been removed. It may take two or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV.
24. Ventilation Install the TV where there is proper ventilation. Do not install
in a conned space such as a bookcase. Do not cover the TV
with cloth or other materials (e.g., plastic) while it is plugged in. Do not install in excessively dusty places.
25. If you smell smoke or other odors coming from the TV or
hear strange sounds, unplug the power cord, and contact an authorized service center.
26. Keep the product away from direct sunlight.
27. When mounting a TV on the wall, make sure that none of the
electrical cabling bears any of the weight of the TV. Install in accordance with the manufacturer’s instructions.
28. Do not install this product on a wall if it could be exposed to
oil or oil mist. This may damage the product and cause it to fall.
29. Do not allow an impact shock or any objects to fall into the
product, and do not drop objects onto the screen.
30. Do not touch the ventilation openings, as they may become
hot while the TV is operating. This does not affect the perfor­mance of the product or cause defects in the product.
31. Do not use high voltage electrical equipment near the TV
(e.g., a bug zapper). This may result in product malfunction.
32. Dot Defect
This panel is an advanced product that contains millions of
pixels. In a very few cases, you could see ne dots on the
screen while you are viewing the TV. Those dots are deacti­vated pixels and do not affect the performance and reliability of the TV.
33. Generated Sound
“Cracking”: A cracking noise that occurs while the TV is on or when it is turned off is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.
34. If the TV feels cold to the touch, there may be a small “icker”
when it is turned on. This is normal; there is nothing wrong with the TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid
touching the screen or holding your nger(s) against it for
long periods of time. Doing so may produce some temporary distortion effects on the screen.
35. Displaying a still image for a prolonged period of time may
cause image burn-in. Avoid displaying a xed image on the
TV screen for an extended length of time.
4
206-4344
Table of Contents
Safety Warnings .................................. 2
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4
Table of Contents ...............................5 – 6
Commercial Mode Overview ....................7
Setup Checklist ................................. 7
Pass-through Mode.............................. 7
FTG Mode..................................... 8
Application Tuning Mode / Pro:Centric Direct......... 10
Determining the TV Operating Mode ................
Pro:Centric Operation ........................12 – 16
Interactive Menu Features ....................... 12
Interactive Menu Navigation ...................... 12
Pro:Centric Java Application Setup ................ 14
Pro:Centric Direct HTML Application Setup .......... 15
First Use Wizard .............................17 – 19
Before You Begin .............................. 17
Initiate Configuration or Exit the First Use Wizard ..... 18
Basic Settings Wizard ........................20 – 24
Hospital Setup Wizard ........................25 – 34
Configure Pro:Centric Settings .................... 25
Complete the TV Configuration ................... 27
Channel Banks Overview . . . . . . . . . . . . . . . . . . . . . . . . 32
EZ-Manager Wizard ..........................35 – 46
TV Configuration Options.......................... 35
Zones and Room Number Assignments ............. 36
Network Settings............................... 37
Configure Pro:Centric Settings .................... 40
USB Configuration ............................. 44
Ez Download Utility ..........................47
Before You Begin .............................. 47
Accessing and Using the Ez Download Utility ........ 47
Installer Menu ...............................52 – 63
Accessing the Installer Menu ..................... 52
Navigating Within the Installer Menu ............... 53
Modifying Installer Menu Settings.................. 53
Exiting the Installer Menu and Activating Settings ..... 53
Detailed Descriptions of Installer Menu Items ........ 56
– 11
11
– 51
Custom Master TV Setup..................... 64
Before You Begin .............................. 64
Clonable TV Setup Menu Features ................ 64
Custom Master TV Setup Procedure ............... 65
Cloning Procedures ..........................68
Exporting a Clone File .......................... 68
Importing a Clone File........................... 70
Cloud Configuration Tool Overview .............75 – 81
Creating an FTG Configuration File ................ 75
File Manager Web Page Overview................. 78
Channel Map Web Page Overview................. 79
Installer Menu Web Page Overview ................ 81
IP Environment Setup ........................82 – 94
Accessing the IP Environment Menu ............... 82
Network Configuration .......................... 82
Pro:Centric Setup .............................. 87
Portal Settings................................. 90
Media Share Setup ............................. 92
References
Updating TV/PTC Software using a USB Memory
Device......................................95 – 96
Downloading Images or Icons using a USB Memory
Device......................................97 – 99
Downloading a Hotel (Hospital) Video using a
USB Memory Device ........................100 – 102
Downloading a Pro:Idiom Media Key using a USB
Memory Device ................................ 103
Power Consumption Settings...................... 104
TV Aux Input Configuration ....................... 105
b-LAN Setup & Overview ......................... 106
FTG Mode via EBL (Local Configuration) ........107 – 108
Auto Input(s) Sensing Feature .................109 – 110
UT672M Hospital Operations.................. 111 – 112
Restoring Factory Defaults on the TV(s) ..............113
Using the TV’s Zoning Features................114 – 117
Using Media Share Features ..................11 8 – 119
UT672M Rear and Side Jack Panels................ 120
Installer Remote Control Typical Key Functions ....... 121
– 67
74
Notes
Installer Menu content is intended for use primarily by qualied TV electronics technicians.
Refer to the applicable Owner’s Manual and/or Easy Setup Guide for additional information on TV installation, specications, maintenance,
and safety instructions.
Design and specications subject to change without prior notice. This document provides examples of typical TV displays. Your displays
may vary from those shown in this document.
206-4344
5
Table of Contents (Cont.)
LG Pro:Centric Patient Remote and Pillow
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 – 123
Pillow Speaker Setup ........................124 – 125
VESA Standard TV Mounts ....................... 126
TLT Communication Parameters ...............127 – 133
Troubleshooting ............................134
General Troubleshooting........................ 134
General Troubleshooting (Cont.) / Commercial
Mode Check / ................................ 135
FTG Operation Troubleshooting / Channel Banks
Setup Troubleshooting ......................... 136
Glossary of Terms .............................. 137
Document Revision History / Open Source Software
Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Back Cover.................................... 139
136
6
206-4344
Commercial Mode Overview
This document describes how to set up UT672M Pro:Centric ® TVs for Commercial Mode operation.
LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translation Controller (PTC), or embedded b-LAN™ (EBL) module, or it resides in a Pro:Centric application or an external device from the solution provider.
These TV models support several different operational modes: LG’s Free-To-Guest (FTG) Mode via the TV CPU, FTG Mode via the TV’s EBL module, Application Tuning Mode (ATM) with Pro:Centric application, or Pass-through Mode (default). When in Pass-through Mode, these TV models can also be externally controlled via Multiple Protocol Interface (MPI) or TV-Link Tuner (TLT) interface (RS-232C).
Setup Checklist
Note: This document provides information specific to Commercial Mode operation. Refer to the Owner’s
Manual and/or Easy Setup Guide for information on TV installation and hardware and cable connections.
Installation
__ Unpack TV and all accessories. __ Install batteries in the Installer Remote. __ Install TV on VESA mount or stand. Note: It may be advisable to make all cable
connections before installing on VESA mount or stand, as appropriate.
Hardware Connections
__ Install any additional hardware as
appropriate to your institution, LAN, etc.
Cable Connections
__ Make all rear jack panel connections, as
appropriate.
Commercial Mode Setup
__ Complete appropriate procedures as described
in this document for Commercial Mode operation.
Pass-through Mode
This mode allows you to configure individual TVs for Pro:Centric and/or FTG Mode via CPU operation. This mode also allows external control via either the GAME CONTROL/MPI port or the TLT (RS-232C) port on the TV rear jack panel.
There are several methods for configuring individual TVs that are currently in Pass-through Mode: using one of the First Use Wizard options or using the Custom Master TV Setup procedure.
First Use Wizard
When the TV is in a factory default state, the First Use Wizard provides four conguration options, including conguration of basic settings (language & location, network settings, etc.), conguration via Hospital Setup Wizard (streamlined conguration of the TV for FTG Mode via CPU with Hospital Mode features), conguration via EZ-Manager Wizard (automated or manual options for conguring essential items for Pro:Centric operation), and conguration via the IP Environment Menu (network settings,
manual Pro:Centric settings, etc.). Use the Installer Remote to make selections and complete each step. See “First Use Wizard” on pages 17 to 19 for further information.
Custom Master TV Setup
The Custom Master TV Setup procedure enables you to create a customized Master TV Setup for Pass-through Mode or FTG Mode via CPU configuration purposes. Use the Installer Remote to congure Installer Menu items as required for TV operation and set up TV features (Channels, Picture, Sound, etc.). See “Custom Master TV Setup” on pages 64 to 67 for detailed information.
206-4344
7
Commercial Mode Overview (Cont.)
Installer Menu
To create a Master TV Setup, you will need to know how to access the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. See pages 52 to 63 for information on accessing the Installer Menu and for detailed descriptions of the Installer Menu items.
PTC INSTALLER MENU
xxUT672M CPU - CTV
000 INSTALLER SEQ 000
TV Setup Menus
On-screen setup menus control the features of the TV. Use the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user.
Cloning
Cloning refers to the process of using a Master TV Setup to congure
a Target TV. The Master TV’s clonable setup menu features should
be congured as part of the Master TV Setup. If there are features in
the Master TV’s setup—channel icons or labels, digital font options, etc.—that are not set or that are set incorrectly, those features also will not be set or will be set incorrectly in the Target TVs. See pages 68 to 74 for detailed information on Clone (.tlx) les and cloning requirements and procedures.
External Control
To control the TV using an external MPI control device, you must use the TV’s GAME CONTROL/MPI port for communication purposes. In these TVs, Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port; therefore, to ensure that the GAME CONTROL/ MPI port circuitry is powered, thus enabling MPI communication, Installer Menu item 118 POWER SAVINGS must be set appropriately. See Installer Menu item descriptions as well as Reference section, “b-LAN Setup & Overview,” for further information.
To control the TV using an external TLT control device, you must use the TV’s RS-232C port for communication purposes. See Reference section, “TLT Communication Parameters,” for further information.
FTG Mode
In this mode, an FTG Channel Map enables the decryption of each
Pro:Idiom ® encrypted channel. The FTG Channel Map also provides
logical channel mapping of physical RF channels (digital and analog), IP streams, and Aux inputs. The method for creating the FTG Channel Map is ultimately determined by which element of the TV will “own” the FTG Channel Map—the CPU or the EBL.
For these TV models, there are two FTG Modes—FTG Mode via CPU and FTG Mode via EBL—which are separate and distinct FTG Modes of operation, each with its own unique advantages and requirements, as outlined below.
UPN 000-000-000-000 S3 ##.## 7F78
PTC V#.##.### CPU V#.##.##.##
Typical Installer Menu
X
TV Setup Menus (Quick Settings)
Picture
PICTURE
Sound
Picture Mode Settings
Channels
Aspect Ratio Settings
16:9
Additional Settings
General
Safety
Accessibility
TV Setup Menus (Advanced Settings)
8
206-4344
Commercial Mode Overview (Cont.)
When the TV CPU is configured with an FTG Channel Map, the CPU controls and restricts the tuning operation of the TV, and when the EBL is configured with an FTG Channel Map, the EBL controls and restricts the tuning operation of the TV. In these models, depending on the types of channels included in the FTG Channel Map, FTG Mode via CPU also provides the option to select either logical or physical tuning (see notes at the top of the following page) during configuration. You must determine which element of the TV will own the FTG Channel Map before you can begin configuration.
FTG Mode via CPU
This mode provides the following features:
• Logical or physical channel tuning of physical RF channels and Aux inputs.
• Logical channel tuning of IP streams.
• Mapping of RF channels with minor (program) numbers up to 999.
• FTG Channel Map of up to 600 channels.
• Start Channel set for RF, Aux input, or IP delivered content.
• Pro:Centric data delivery over RF or IP.
• TV Zoning (including channel restrictions by Zone) and
Wi-Fi Zoning options for location-specic congurations.
LG’s Cloud Conguration Tool enables you to create an FTG Conguration (.tlx) le, which may be used to congure the CPU for FTG Mode. You can also create a Clone (.tlx) le from a Master TV Setup that may be used to congure the CPU for FTG Mode.
Note: TV Zoning and Wi-Fi Zoning features are
supported via “.tlx” le. See Reference section, “Using
the TV’s Zoning Features,” for further information.
In this mode, the CPU is the owner of the FTG Channel
Map and must be congured with an FTG Channel Map
and FTG Installer Menu settings using one of the following processes:
Local: Congure an individual UT672M TV via its USB
port using a USB memory device / “.tlx” le. The le may be either a Clone le (see “Cloning Procedures” on pages 68 to 74) or an FTG Conguration le (see “Cloud Conguration Tool Overview” on pages 75 to 81).
Remote: Congure all UT672M TVs at the site using a Pro:Centric server head end device (Example: PCS400R). Refer to the Pro:Centric Server Admin Client User Guide for further information.
FTG Mode via EBL
This mode provides the following features:
• Logical channel tuning of physical RF channels and Aux inputs.
• Mapping of RF channels with minor (program) numbers up to 255.
• FTG Channel Map of up to 141 logical channels.
• Start Channel set for RF or Aux input delivered content.
• Pro:Centric data delivery over RF.
LG’s FTG Device Conguration Application PC software is required to congure the EBL. In this mode, the EBL
is the owner of the FTG Channel Map and must be
congured with an FTG Channel Map and FTG Installer
Menu settings using one of the following processes:
Note: In order to create an FMA Conguration (.fma) le for these models that can be used for remote
management of FTG Installer Menu settings, you will need to “Read” FTG Installer Menu settings from a Master TV. See Reference section, “FTG Mode via EBL
(Local Conguration),” for further information.
Local: Congure an individual UT672M TV’s EBL via its TV-LINK CFG jack using a direct PC-to-TV (EBL) connection and the FTG Device Conguration Application. See Reference section, “FTG Mode via
EBL (Local Conguration),” for information on the
“Write” process for an FTG Channel Map and FTG Installer Menu settings.
Remote: Congure all UT672M TV EBLs at the site using a Free-To-Guest Management Appliance (FMA) head end device (Example: FMA-LG102). Refer to the Free-To-Guest (FTG) Device Configuration Application User Guide and/or the Installation &
Conguration Guide for the FMA device for further
information.
206-4344
9
Commercial Mode Overview (Cont.)
Note: Logical channel mapping of physical RF channels eliminates dash tuning; for example, physical 19-3
can be mapped to logical channel 9. It also allows physical RF channels, IP streams, and Aux inputs to be listed in any order, not only in physical numeric ascending order. Physical channel tuning requires that you include the dash when direct entering RF channel numbers and Aux inputs (the latter designated by 130-0 through 137-0).
Note: Physical channel tuning is not available when IP channels are included in the FTG Channel Map.
While the TV is in FTG Mode:
• Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu items will be read-only.
FTG Mode via CPU conguration changes must be made using a “.tlx” le (typically edited in the Cloud
Conguration Tool), while FTG Mode via EBL conguration changes must be made using the FTG Device Conguration Application. Channel Map and Installer Menu conguration utilities in both applications
enable you to make changes, respectively, to the FTG Channel Map and FTG Installer Menu settings as necessary. Based on the initial method used to congure the TV for FTG Mode operation (via CPU or EBL), all subsequent changes must be transferred to either the TV CPU or the EBL via a process that is in accordance or compatible with that method (see information on local conguration in this document or refer to documentation for the head end device/server for information on remote management).
• If it becomes necessary to restore the TV to Pass-through Mode, there are several options that will enable you to do so. See Reference section, “Restoring Factory Defaults on the TV(s),” for further information.
Pages 75 to 81 provide overviews of the utilities that comprise the Cloud Conguration Tool. Refer to the Cloud Configuration Tool User Guide for further information on the Cloud Conguration Tool. Refer to the Free-To-Guest (FTG) Device Configuration Application User Guide for information on the FTG Device Configuration Application.
Remote Management in FTG Mode
When the TV is configured for FTG Mode via CPU, remote management of the FTG Channel Map and FTG Installer Menu settings is provided by a Pro:Centric server, via a Clone/Configuration (.tlx) file loaded on the Pro:Centric Admin Client. See the Pro:Centric Server Admin Client User Guide for further information.
When the TV is configured for FTG Mode via EBL, the b-LAN module, which is internal to the TV, allows hospital/institution head end equipment (for example, an FMA-LG102) with b-LAN technology to provide remote management of the FTG Channel Map and FTG Installer Menu settings. See Reference section, “b-LAN Setup & Overview,” for further information.
Application Tuning Mode / Pro:Centric Direct
In Application Tuning Mode, the TV’s Channel Map resides in an application, such as LG’s Pro:Centric Direct HTML application. With Pro:Centric Direct, the Channel Map is created in the Pro:Centric server’s Admin Client web editor, and the tuning operation of the TV is controlled and restricted based on this Pro:Centric Direct Channel Map.
Application Tuning Mode with the Pro:Centric Direct HTML application provides the following features:
Decryption of each Pro:Idiom ® encrypted channel.
• Logical channel tuning of physical RF channels (digital and analog) and IP streams.
• Mapping of RF channels with minor (program) numbers up to 999.
• Start Channel set for RF or IP delivered content.
10
206-4344
Commercial Mode Overview (Cont.)
• Pro:Centric data delivery over RF or IP.
TV Zoning (Installer Menu items only) and Wi-Fi Zoning options for location-specic congurations.
You must use the Pro:Centric Direct Admin Client / Channel Map conguration utility to create the Pro:Centric Direct Channel Map, dene channel attributes, and set the Start Channel. Refer to the
Pro:Centric Direct Admin Client User Guide for further information.
Note: TV Zoning and Wi-Fi Zoning features are supported via “.tlx” le—typically a Clone (.tlx) le that has
been created from a Master TV Setup. See Reference section, “Using the TV’s Zoning Features,” for further information.
While the TV is in Application Tuning Mode:
• Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu items will be read-only.
• While it is possible to update a TV’s Installer Menu and/or Setup Menu settings locally using a USB
memory device / Clone (.tlx) le, any Pro:Centric Direct conguration changes are typically made
remotely via the Pro:Centric server / Pro:Centric Direct Admin Client. The Admin Client’s Channel Map
conguration utility enables you to create and edit the Pro:Centric Direct Channel Map, while the TV Conguration utility (in conjunction with a Clone [.tlx] le loaded on a server carousel) enables you to
make changes to TV Installer Menu and/or Setup Menu settings.
• If it becomes necessary to restore the TV to Pass-through Mode, it is possible to do so. See Reference section, “Restoring Factory Defaults on the TV(s),” for further information.
Refer to the Pro:Centric Direct Admin Client User Guide for further information on conguration and management via the Pro:Centric Direct Admin Client.
Determining the TV Operating Mode
To determine the operating mode of the TV, press MENU on the Installer Remote. The menu displayed depends on the operating mode. See examples below.
If the Function Menu appears, the TV is in a mode (FTG, ATM, PPV, etc.) that does not allow the end user to change the fundamental TV setup. If the TV setup menus (Quick Settings) appear, the TV is in Pass-through Mode.
Aspect Ratio
ASPECT RATIO
Sound Out
Aspect Ratio
16:9
Audio Mode
Just Scan
O
General
Safety
Accessibility
Function Menu
Indicates the TV is not in
^
Pass-through Mode . While the TV is in this mode, Installer Menu settings can be accessed as read-only.
X
TV Setup Menus
Shows that the TV is in Pass-through Mode .
206-4344
11
Pro:Centric Operation
These TV models support LG’s Pro:Centric Java application, as well as the Pro:Centric Direct HTML application. Only one application may be implemented at a time. The following sections provide an overview of the application features and functionality.
Interactive Menu Features
Both the Pro:Centric Java (GEM) application and the Pro:Centric Direct HTML application enable patients and visitors to locate and select television entertainment, check the daily weather, view hospital and surrounding amenities, etc. via custom portal interactive menus. The Pro:Centric Java application provides multiple templates for portal interactive menus, while the Pro:Centric Direct HTML application, in addition to providing multiple templates for portal interactive menus, also enables you to custom-create portal and application content.
Pro:Centric application features include:
• Portal and information screens/pages (including a “Welcome” page) that include branding logos.
• An optional customized user interface (custom “skins”).
• Billboards and points-of-interest maps that can be customized to focus on hospital amenities, local attractions and businesses, hotels, restaurants, news, events, etc.
• An optional Weather billboard that includes a local radar map, current conditions, and a four day forecast.
• An interactive channel guide that provides a channel list with channel icons. An electronic program guide (EPG) is an optional feature that displays up to three days of programming information viewable by channel and time.
Video spooling that enables the hospital to deliver a video le to patient and visitor TVs for promotion and information purposes.
In addition to the those indicated above, the Pro:Centric Direct HTML application also offers the following features:
• Optional messaging features, including notices, ticker text, and ad banners.
Additional media support, specically music accompaniment, for portal displays.
An optional ight information display.
For each Pro:Centric application, an Admin Client web editor/content wizard is provided for customer conguration of portal content. The Pro:Centric Direct Admin Client features the Pro:Centric Direct Project Editor, which provides design tools (including templates) that enable customization of all portal pages. Please contact your LG service representative for further information.
Note: Customized content is typically dened by the service integrator and/or hospital administrators. LG does not provide hospital-specic content.
Interactive Menu Navigation
LG’s Pro:Centric pillow speaker provides access to both interactive menus and regular TV features. Press PORTAL on the Pro:Centric pillow speaker to access the interactive menus.
Interactive menu options may vary, depending on Pro:Centric features enabled for the site and/or customized content. The following examples show typical portal interactive menus.
12
206-4344
Example: Pro:Centric Java (GEM) Application Portal
Pro:Centric Operation (Cont.)
Example: Pro:Centric Direct HTML Application Portal
206-4344
13
Pro:Centric Operation (Cont.)
Pro:Centric Java Application Setup
The Pro:Centric Java (GEM) application operates in conjunction with FTG and PPV Modes. This section provides an overview of the setup required for the Pro:Centric features. Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric Server Admin Client
User Guide. This document describes only those settings that must be specied on the TVs to enable
Pro:Centric remote management and/or the Pro:Centric Java application.
• Remote management (TV E-Z Installation): The Pro:Centric Admin Client provides remote management facilities for downloading boot logo image and software updates as well as facilities for downloading a Clone/Configuration (.tlx) file for FTG Mode via CPU configuration.
• Pro:Centric Java application: The application comprises the Pro:Centric interactive menus/features described on page 12. Pro:Centric application settings are managed via the Pro:Centric Admin Client for the Java application.
The Pro:Centric remote management facilities and application download are based on Installer Menu item settings that are used to set up the TV’s Pro:Centric features. The Installer Menu / Pro:Centric server
settings can be congured using one of the methods described below.
Note: If using a Pro:Centric pillow speaker, also set Installer Menu item 027 HOSPITAL MODE to the required value.
TV in Factory Default State
When the TV is in a factory default state, LG’s First Use Wizard provides automated or manual options for conguring the TV’s Pro:Centric server settings. See “First Use Wizard” on pages 17 to 19 for further information. The First Use / EZ-Manager Wizard also provides a USB conguration option that enables
you to congure a TV for FTG Mode via CPU using a Clone/Conguration (.tlx) le stored on a USB memory device. The “.tlx” le incorporates FTG Installer Menu settings, including Installer Menu items 098
PRO:CENTRIC and 119 DATA CHANNEL, which are used to set up the TV’s Pro:Centric features.
TV in Pass-through Mode
If the First Use Wizard has been exited and the TV is in Pass-through Mode, either:
• Set Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL to the appropriate values. See Installer Menu information on pages 52 to 63 for further details. Also, as necessary, refer to “Custom Master TV Setup” on pages 64 to 67 and/or cloning information on pages 68 to 74.
Congure the appropriate Pro:Centric server settings in the IP Environment / Pro:Centric Menu. You must
use this option, in particular, if you wish to congure IP settings for the Pro:Centric server. See “Accessing
the IP Environment Menu” on page 82 and “Pro:Centric Setup” on pages 87 to 90 for further information.
Note: When the TV is in either Pass-through Mode or FTG Mode via CPU, you can also leave Installer Menu item 119 DATA CHANNEL set to its default value (255) to enable the TV’s Data Channel Auto Search feature to set the DATA CHANNEL value. See item 119 description on page 62 for additional information.
TV in FTG Mode
If the TV is already in FTG Mode (via CPU or EBL), use the appropriate FTG application to update Installer Menu items #98 Pro:Centric and #119 Data Channel (along with their affiliated fields). Then, transfer the FTG Installer Menu settings to the TV in accordance with the FTG Mode of configuration. Refer to the FTG Mode overview on pages 8 to 10 for further information on FTG Mode operation and configuration. Also—for FTG Mode via CPU only—see note above regarding the option to use the TV’s Data Channel Auto Search feature to set the DATA CHANNEL value.
14
206-4344
Pro:Centric Operation (Cont.)
Pro:Centric Direct HTML Application Setup
The Pro:Centric Direct HTML application operates only in Application Tuning Mode (ATM). This section provides an overview of the setup required for the Pro:Centric Direct features. Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric Direct Admin Client User Guide. This document describes only those settings that must be specied on the TVs to enable Pro:Centric remote management and/or the Pro:Centric Direct HTML application.
• Remote management (TV E-Z Installation): The Pro:Centric Direct Admin Client provides remote management facilities for downloading boot logo image and software updates as well as facilities for downloading Installer Menu configuration updates via Clone (.tlx) file to the TVs at the site/institution.
Note: The Pro:Centric Direct Channel Map is created and maintained in the Pro:Centric Direct Admin Client. Thus, any Clone le that is loaded on the server for remote conguration may only contain Installer
Menu and/or Setup Menu proles.
• Pro:Centric Direct HTML application: The application comprises the Pro:Centric interactive menus/ features described on page 12. Pro:Centric Direct application settings are managed via the Pro:Centric Direct Admin Client.
The Pro:Centric remote management facilities and application download are based on Installer Menu item settings that are used to set up the TV’s Pro:Centric features. The Installer Menu / Pro:Centric server
settings can be congured using one of the methods described below.
Note: If using a Pro:Centric pillow speaker, also set Installer Menu item 027 HOSPITAL MODE to the required value.
TV in Factory Default State
When the TV is in a factory default state, LG’s First Use Wizard provides automated or manual options
for conguring the TV’s Pro:Centric server settings. See “First Use Wizard” on pages 17 to 19 for further information. The First Use / EZ-Manager Wizard also provides a USB conguration option that enables you to congure the TV’s Installer Menu settings using a Clone (.tlx) le stored on a USB memory device.
Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL are used to set up the TV’s Pro:Centric features.
TV in Pass-through Mode
If the First Use Wizard has been exited and the TV is in Pass-through Mode, either:
• Set Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL to the appropriate values. See Installer Menu information on pages 52 to 63 for further details. Also, as necessary, refer to “Custom Master TV Setup” on pages 64 to 67 and/or cloning information on pages 68 to 74.
Congure the appropriate Pro:Centric server settings in the IP Environment / Pro:Centric Menu. You
must use this option, in particular, if you wish to congure IP settings for the Pro:Centric server. See
“Accessing the IP Environment Menu” on page 82 and “Pro:Centric Setup” on pages 87 to 90 for further information.
Note: When the TV is in either Pass-through Mode or Application Tuning Mode, you can also leave Installer Menu item 119 DATA CHANNEL set to its default value (255) to enable the TV’s Data Channel Auto Search feature to set the DATA CHANNEL value. See item 119 description on page 62 for additional information.
206-4344
15
Pro:Centric Operation (Cont.)
TV in Application Tuning Mode
If the TV is already in Application Tuning Mode, use a Master TV of the same model to create and
export a Clone (.tlx) le with the desired settings for Installer Menu items 098 PRO:CENTRIC and 119
DATA CHANNEL. Then, transfer (import) the Clone le to the Target TV. Refer to the Application Tuning Mode / Pro:Centric Direct overview on pages 10 to 11 for further information on Pro:Centric Direct operation
and conguration. To transfer the Clone le remotely, use the appropriate utilities in the Pro:Centric Direct Admin Client to upload the Clone le to the Pro:Centric server and set up its distribution to the Target
TV(s) at the site. See also note above regarding the option to use the TV’s Data Channel Auto Search feature to set the DATA CHANNEL value.
16
206-4344
First Use Wizard
Note: After it is turned ON, the TV begins an initialization process, and it may take several minutes
for the First Use Wizard to appear.
LG’s First Use Wizard, comprising multiple configuration options, will appear on the screen each time the TV is turned ON, until one of its configuration methods has been completed or the wizard is exited. Use the Installer Remote to make selections and complete each step.
• Basic Settings: Initiates the Basic Settings Wizard, which enables you to select basic TV settings, including the TV’s language and location, and run Channel Tuning. It also allows you to congure the TV’s network settings, as well as custom portal settings, if desired. See “Basic Settings Wizard” on pages 20 to 24 for further information.
• Hospital Settings: Initiates the Hospital Setup Wizard. The Hospital Setup Wizard guides you through the process of conguring the TV for FTG Mode via CPU operation with Hospital Mode features. This includes setting up the pillow speaker, as required, as well as setting up channel banks (up to four) for tiered channel programming. The Hospital Setup Wizard also enables you to congure the Pro:Centric settings on the TV. See “Hospital Setup Wizard” on pages 25 to 34 for further information.
Note that the Hospital Setup Wizard uses the TV’s standard RF Auto Tuning feature to create the TV’s channel lineup; IP channels are not supported.
• Advanced Settings (default): Initiates the EZ-Manager Wizard. The primary purpose of the EZ-
Manager Wizard is to guide you through the process (automated or manual) of conguring the
essential Installer Menu items for Pro:Centric operation.
While the EZ-Manager Wizard is intended primarily for Pro:Centric-related conguration, the wizard also offers Zoning and network conguration options and, in addition, enables you to access the TV Manager / USB download options as part of the conguration process, if desired, to perform USB conguration and/or update functions. See “EZ-Manager Wizard” on pages 35
to 46 for further information.
• IP Environment Settings: Enables you to access the IP Environment Menu to set up network features of the TV, including Pro:Centric and/or Media Share features. See “IP Environment Setup” on pages 82 to 94 for further information.
Caution: Do NOT unplug the TV power cord or remove the antenna cable or, if
applicable, the LAN cable during the conguration process, as doing so will interrupt the current step and may corrupt the conguration data.
Note: If you do not intend to complete the Hospital Setup Wizard, but you wish to enable Hospital Mode (pillow speaker functionality and also channel banks), you must set Installer Menu item 027 HOSPITAL MODE appropriately. See the “Installer Menu” section of this document for further information.
Before You Begin
• If you plan to create a customized Master TV Setup using the procedure described on pages 64 to 67, be sure to exit the LG First Use Wizard in order to avoid setup conicts or setting modes that may cause unintended behavior or restrict the custom setup procedure. See also “Initiate
Conguration or Exit the First Use Wizard” on the following page.
• If it has been completed or exited and therefore does not display, the First Use Wizard can be reactivated; however, this requires that you restore the TV to a factory default condition. See Reference section, “Restoring Factory Defaults on the TV(s),” for further information.
206-4344
17
First Use Wizard (Cont.)
• If you would like to enable the SoftAP and/or Beacon Media Share features or select
pre-loaded / Smart Launcher applications on a TV that will eventually be congured for FTG Mode, you will need to use the IP Environment Menu to do so before the TV is congured for FTG Mode. You can access the IP Environment Menu from the First Use Wizard or from the
Installer Menu. See “Initiate Conguration or Exit the First Use Wizard” below for information on accessing the IP Environment Menu from the First Use Wizard, and refer to “IP Environment Setup” on pages 82 to 94 for detailed information on the IP Environment Menu (as well as information on accessing the IP Environment Menu from the Installer Menu). See also “Custom Master TV Setup” on pages 64 to 67, as necessary.
Initiate Conguration or Exit the First Use Wizard
The Welcome screen provides a brief introduction to the First Use Wizard.
WELCOME TO LG’S FIRST USE WIZARD
Select the desired option, and then select START to continue.
Basic Settings
Quick settings for basic use (language, network, portal, voice service, channe...
Hospital Settings
Use the Hospital Setup Wizard to configure the TV for FTG Mode via CPU with...
Advanced Settings
Use the EZ-Manager Wizard to configure the TV for Pro:Centric operation.
IP Environment Settings
Access the IP Environment Menu.
EXIT
START
Use the arrow keys on the Installer Remote to select the desired option in the Welcome screen:
• To proceed with the Basic Settings Wizard, select/highlight Basic Settings, and then press OK. Then, select START and press OK to continue. See “Basic Settings Wizard” on pages 20 to 24 for further information.
• To proceed with the Hospital Setup Wizard, select/highlight Hospital Settings, and then press OK. Then, select START and press OK to continue. See “Hospital Setup Wizard” on pages 25 to 34 for further information.
• To proceed with the EZ-Manager Wizard, select/highlight Advanced Settings, and then press OK. Then, select START and press OK to continue. See “EZ-Manager Wizard” on pages 35 to 46 for further information.
• To access the IP Environment Menu, select/highlight IP Environment Settings, and then press OK. Then, select START and press OK to continue. See “IP Environment Setup” on pages 82 to 94 for further information.
• To exit the First Use Wizard, select/highlight the EXIT button at the bottom of the screen, and then press OK. In the exit conrmation screen, select EXIT, and then press OK once more on the Installer Remote.
18
206-4344
First Use Wizard (Cont.)
Note: Both the EZ-Manager Wizard and the Hospital Setup Wizard enable you to congure
Pro:Centric settings on this TV, even if you do not intend to congure any of the additional settings available. After you congure the Pro:Centric settings, you will have the option to exit without
completing the remainder of the EZ-Manager Wizard or Hospital Setup Wizard (as applicable), if desired.
Note: If you exit the First Use Wizard from the Welcome screen, no conguration will be performed and all Installer Menu items will retain their default values, including Installer Menu item 119 DATA CHANNEL. The default DATA CHANNEL setting (255) means that the Pro:Centric remote management feature on this TV will be activated if a Pro:Centric server is installed and the Data Channel value is set during a Data Channel Auto Search (see item 119 description on page 62 for additional information). If you actually would like to disable the Pro:Centric feature, the EZ-Manager Wizard, Hospital Setup Wizard, and the IP Environment Menu provide an option to do so, and/or you may disable Pro:Centric by modifying the value of Installer Menu item 119.
206-4344
19
Basic Settings Wizard
This section describes the conguration options available when you select “Basic Settings” from the First Use Wizard / Welcome screen. You can select the “BACK” button, where available, to check previous settings, as necessary.
Note: Each Basic Settings Wizard step is allotted a 10-second time frame after which the wizard proceeds without user interaction. If default settings are appropriate, the wizard can proceed through
each of the conguration steps with no further user interaction. If you turn OFF the TV while the
wizard is in progress, when you turn the TV back ON, the First Use Wizard / Welcome screen will
be displayed. You will then have the opportunity to (re)initiate the desired conguration process.
Note: To exit the wizard at any time, use the arrow keys on the Installer Remote to select/highlight
X
the
button at the top right of the screen, and then press OK. In the exit conrmation screen, select
EXIT, and then press OK once more on the Installer Remote.
1. In the Language & Location screen, use the arrow keys on the Installer Remote to select/high-
light each appropriate eld in turn—Language or Time Zone—and then press OK. Then, use the up/down arrow keys to select the applicable value from the drop-down list of options for the selected eld. When you are ready to continue, use the arrow keys on the Installer Remote to select NEXT, and then press OK.
Note: The Country eld is inaccessible/grayed out because these models are only available in
the US. Also, if you allow the wizard to progress without specifying data in this screen, the time
zone will be set for “New York” (Eastern Standard Time).
X
LANGUAGE & LOCATION
Confirm your language and location settings.
^
Language
English
^
Country
Disabled
^
Time Zone
New York
BACK
This wizard will continue automatically in 10 seconds.
NEXT
01
2. The next screen enables you to congure the network settings of the TV. Refer to the appropriate subsection(s) below for information on conguring the wired and/or wireless connection(s)
between the TV and the network. When you are ready to continue, use the arrow keys on the Installer Remote to select NEXT, and then press OK.
Note: If desired, you can congure both wired and wireless connections. However, note that a wired connection is always prioritized over a wireless connection. That is, when the TV is turned OFF and then back ON, if a Local Area Network (LAN) is detected by the TV, the TV will default to the wired connection. If the LAN cable is removed, the TV will then attempt to establish the wireless connection. Whenever the TV is reconnected to the LAN, the TV will re-establish the wired connection.
20
(Continued on next page)
206-4344
Basic Settings Wizard (Cont.)
(Continued from previous page)
Note: If a cable is not currently connected between the TV and the network and you do not want
to congure/complete conguration of network settings at this time, you can select/highlight
SKIP, and press OK on the Installer Remote to continue to the next step.
Congure a Wired Network Connection
X
NETWORK SETTINGS
Configure network settings.
Network Connection Type
Wired (Ethernet)
Advanced Options
^
IPv6
Disabled
Automatically Assign IP Address
IP Address
10.1.2.3
Subnet Mask
255.255.255.0
BACK
NEXT
This wizard will continue automatically in 10 seconds.
NEXT
^
^
^
02
a. If not already done, connect the appropriate cable between the TV and the network.
b. Make sure the Wired (Ethernet) option is selected in the Network Connection Type eld,
and then press OK on the Installer Remote.
c. By default, the TV uses DHCP, and if a LAN is detected, the TV will request an IP address
from the DHCP server on the network. If the TV is able to connect to the network, the network
conguration data will be displayed on the screen as shown in the example above.
If the network is not congured for DHCP, or if you want to enable/disable IPv6 or specify static IP conguration data, continue with steps (d) and/or (e), respectively.
d. (Optional) To enable IPv6, select/highlight the IPv6 eld and press OK. Then, select Enabled
from the drop-down list of options.
e. (Optional) If required, you can edit the IP data for this TV as follows:
• De-select the “Automatically Assign IP Address” checkbox under “Advanced Options.”
• For each data entry eld: Use the arrow keys on the Installer Remote to select the eld
and press OK. You can use the number keys on the Installer Remote to direct enter numeric values or use the arrow keys to select the appropriate alphanumeric characters (as applicable) from the pop-up virtual keyboard displayed at the bottom of the screen. When you are done, select Enter from the virtual keyboard, and then press OK on the Installer Remote.
Note: For IPv4, you must use the dot “.” key from the virtual keyboard to separate each octet of an IP address. For IPv6, you must use the colon “:” key from the virtual keyboard to separate each group of an IP address.
206-4344
(Continued on next page)
21
Basic Settings Wizard (Cont.)
(Continued from previous page)
Congure a Wireless (Wi-Fi) Network Connection
NETWORK SETTINGS
Configure network settings.
Network Connection Type
Wireless (Wi-Fi)
Wireless (Wi-Fi) Network
Network A
Advanced Options
^
IPv6
Disabled
Automatically Assign IP Address
IP Address
10.1.2.3
255.255.255.0
BACK
This wizard will continue automatically in 10 seconds.
NEXT
^
^
^
^
X
02
a. Select/highlight the Network Connection Type eld, and press OK on the Installer Remote.
Then, use the Up/Down arrow keys to select/highlight Wireless (Wi-Fi), and press OK once more.
b. Select/highlight the Wireless (Wi-Fi) Network eld, and press OK on the Installer Remote.
Then, use the Up/Down arrow keys to select/highlight the desired access point from the drop-down list of available options, or select the “Hidden Network” option at the bottom of the list to specify an access point with a hidden SSID. Press OK once more.
Note: Make sure you have the network security password—at least eight, but no more than 32 characters—or PIN available if you are attempting to connect to a secured network. If you would like to add an access point with a hidden SSID, you will need to direct enter the SSID— up to 32 characters—of the access point.
c. Follow the on-screen instructions to complete the appropriate network conguration. Use the
Installer Remote to navigate between elds and make entries, etc.
Note: As with a wired connection, you will have the option to specify static IP conguration
data for this network connection. Once the initial connection is established, you can de-select the “Automatically Assign IP Address” checkbox under “Advanced Options,” and then modify the IP data, as required. See step (e) of the wired connection procedure above for further
information on the data entry elds.
d. (Optional) To enable IPv6, select/highlight the IPv6 eld and press OK. Then, select Enabled
from the drop-down list of options.
e. Once the wireless network conguration is complete, use the arrow keys on the Installer
Remote to select CONNECT, and then press OK on the Installer Remote to continue.
Note: The “CONNECT” button becomes a “NEXT” button once the connection is successful.
22
(Continued on next page)
206-4344
Basic Settings Wizard (Cont.)
(Continued from previous page)
3. In the Portal Settings screen, you can specify the Portal Mode and the Portal Auto Start status
for this TV. Use the arrow keys on the Installer Remote to select/highlight each appropriate eld in
turn—Portal Mode or Portal Auto Start—and then press OK. Then, use the up/down arrow keys to select the applicable value from the drop-down list of options for the selected eld. When you are ready to continue, use the arrow keys on the Installer Remote to select NEXT, and then press OK.
Note: Customizable portal settings are for TVs that will NOT be congured for Pro:Centric operation. If the “Customizable Portal” option is selected in the Portal Mode eld, you will be
redirected to the IP Environment / Portal Settings Menu when this wizard is complete, so that you can congure the custom portal settings. The Portal Auto Start status is either “On” (display the portal when the TV is turned ON) or “Off” (do not display the portal when the TV is turned ON).
X
PORTAL SETTINGS
Confirm portal settings.
Portal Mode
Default Portal
Portal Auto Start
O
^
^
03
NEXT
BACK
This wizard will continue automatically in 10 seconds.
4. In the Voice Service Coverage screen, use the arrow keys on the Installer Remote to select/
highlight each appropriate eld in turn—LG Service Country or Service Area Zip Code—and
then press OK. Then, use the up/down arrow keys to select the applicable value from the drop­down list of options for the selected eld. When you are ready to continue, use the arrow keys on the Installer Remote to select NEXT, and then press OK.
X
VOICE SERVICE COVERAGE
Confirm voice service coverage settings.
LG Service Country
United States
Service Area Zip Code
None
BACK
^
^
NEXT
This wizard will continue automatically in 10 seconds.
NEXT
04
(Continued on next page)
206-4344
23
Basic Settings Wizard (Cont.)
(Continued from previous page)
5. The Channel Tuning screen is the nal step of the Basic Settings Wizard.
CHANNEL TUNING
If you intend to run Channel Tuning, first select the tuning band you would like to use.
Select the tuning band you would like to use
Cable Standard
^
X
BACK
DONE
CHANNEL TUNING
This wizard will continue automatically in 10 seconds.
05
• If you would like to initiate an automated channel scan (i.e., a search for all available digital and
analog channels), use the arrow keys on the Installer Remote to select the RF tuning band eld, and select the appropriate option. Then, press OK. Next, select the CHANNEL TUNING button at the bottom of the screen, and press OK.
Tuning progress will be shown in a new Channel Tuning screen. The scan typically takes a few minutes. When the channel scan is complete, the TV will launch the IP Environment Menu. See additional information below.
• If you would like to complete the Basic Settings Wizard without running Channel Tuning, select the
DONE button at the bottom of the screen, and press OK. The TV will launch the IP Environment Menu. See additional information below.
As indicated above, the IP Environment Menu is always launched after the Basic Settings Wizard is complete (and once Channel Tuning is nished, if applicable). If you selected the “Customized Portal” option in the Portal Settings screen, the IP Environment / Portal Settings Menu will be on display when
the IP Environment Menu launches, and you can congure the portal, as desired. If you did not select
“Customized Portal,” the IP Environment Menu launches with the Network Menu options on display (default IP Environment Menu launch scenario). See “IP Environment Setup” on pages 82 to 94 for further information on the options available in the IP Environment Menu.
24
206-4344
Hospital Setup Wizard
This section describes the conguration options available when you select “Hospital Settings” from
the First Use Wizard / Welcome screen. You can select the “BACK” button, where available, to check previous settings, as necessary.
Note: The Hospital Setup Wizard congures the TV for FTG Mode operation with Hospital Mode features. This means that while the TV is functioning in FTG Mode, Hospital Mode is enabled (i.e., Installer Menu item 027 HOSPITAL MODE is not set to 0). In addition, you can create custom channel lineups for channel banks 1 to 4.
Note: While the Hospital Setup Wizard enables you to set up TVs individually in lieu of cloning, you can also use the resulting Hospital TV Setup for cloning purposes, if desired. However, note that TV setup menu customization via the Hospital Setup Wizard is limited to Channels Menu options.
Note: To exit the wizard at any time, use the arrow keys on the Installer Remote to select/highlight
X
the
button at the top right of the screen, and then press OK. In the exit conrmation screen, select
EXIT, and then press OK once more on the Installer Remote.
Congure Pro:Centric Settings
The rst Hospital Setup Wizard screen enables you to set up the Pro:Centric feature of the TV (see screen examples below). By default, the Data Channel is congured for Auto Search, which
enables the TV’s Data Channel Auto Search feature to set the Data Channel value. See item 119 DATA CHANNEL description on page 62 for further information on the Data Channel Auto Search feature. The Pro:Centric Application Mode default setting is “Conguration Only,” which enables remote management only. That is, the TV will search for TV E-Z Installation data downloads; however, Pro:Centric application data will not be downloaded, i.e., Installer Menu item 098 PRO:CENTRIC will be set to 0.
• If you wish to proceed with the wizard without changing the default values for the Pro:Centric
settings, you can simply select NEXT and press OK on the Installer Remote. Or, if you wish to exit the wizard while retaining the default values for Pro:Centric settings, use the arrow keys on the Installer Remote to select DONE, and then press OK.
• If you already know the Pro:Centric settings that need to be congured in order for the TV to
connect to the Pro:Centric server and/or if the Pro:Centric server is not yet installed, use the procedure on the following page to expedite the setup process. Use the Up/Down arrow keys on
the Installer Remote to navigate between the elds.
PRO:CENTRIC CONFIGURATION
Pro:Centric Mode
Media Type
Data Channel
206-4344
BACK
CONFIGURATION ONLY
<
RF
<
<
AUTO SEARCH
DONE
NEXT
>
>
>
X
01
Pro:Centric Configuration Screen with RF Media Fields
Note: By default, the Pro:Centric
Conguration screen initially shows RF conguration elds.
(Continued on next page)
25
Hospital Setup Wizard (Cont.)
(Continued from previous page)
X
PRO:CENTRIC CONFIGURATION
Pro:Centric Mode
Media Type
Server Address
IP Type
IP Address
IP Port
DONE
BACK
CONFIGURATION ONLY
<
IP
<
<
<
IP Address
IPv4
0 0 0 0
NEXT
0
>
>
>
>
01
Pro:Centric Configuration Screen with IP Media Fields
Note: If you would like to disable the Pro:Centric feature of the TV, select the Data Channel eld,
and then use the Left/Right arrow keys on the Installer Remote to select DISABLED. From here, you may opt to proceed with the wizard (select NEXT) or save this setting and exit the wizard (select DONE). See also step 3 below.
1. In the Pro:Centric Mode eld, use the Left/Right arrow keys on the Installer Remote to select the
appropriate Pro:Centric Application Mode—GEM (Java), HTML, or CONFIGURATION ONLY.
Note: For remote management only, select CONFIGURATION ONLY. The TV will search for TV E-Z Installation data downloads; however, Pro:Centric application data will not be downloaded, i.e., Installer Menu item 098 PRO:CENTRIC will be set to 0.
2. Refer to the appropriate subsection below, depending on the Pro:Centric server conguration, to complete the remaining elds.
RF Conguration
a) In the Media Type eld, use the Left/Right arrow keys on the Installer Remote to select RF.
b) In the Data Channel eld, use the Left/Right arrow keys to select the RF channel number
that will be used by the Pro:Centric server as its data channel. The Data Channel value can be set from 1 to 135. *
IP Conguration
a) In the Media Type eld, use the Left/Right arrow keys on the Installer Remote to select IP.
Note: When you select “IP” as the Media Type, the default RF Data Channel eld is replaced
with Server Address, IP Type, IP Address, and IP Port elds.
b) The Server Address eld provides the option to specify the domain name of the Pro:Centric
server instead of the server’s IP address. Use the Left/Right arrow keys to select the desired option—IP Address or Domain Name—for dening the server.
* PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.
26
(Continued on next page)
206-4344
Hospital Setup Wizard (Cont.)
(Continued from previous page)
c) Depending on your selection in the previous step, either:
Select the appropriate IP type (either IPv4 or IPv6) in the IP Type eld, and then enter the
Pro:Centric server IP address in the IP Address eld. The IP address must match the IPv4
or IPv6 (as applicable) address that is set in the Pro:Centric server.
Enter the Pro:Centric server domain name in the Domain Name eld. Note that in order
for the domain name to be resolved to an IP address, there must be a DNS entry for the domain name.
For each data entry eld: Use the arrow keys to select the eld and press OK. Then, you can either use the number keys on the Installer Remote to direct enter data values, or you can use the arrow keys to select the appropriate number(s)/alphanumeric character(s) from the pop-up virtual keyboard displayed at the bottom of the screen. When you are done, select
Enter from the virtual keyboard, and then press OK on the Installer Remote.
Note: For an IPv6 IP address, you must use the colon “:” key from the virtual keyboard to
separate each group.
d) Enter the Pro:Centric server port number in the IP Port eld. The port number must match
the port number that is set in the Pro:Centric server.
3. Once all elds are completed as required, you have two options:
To proceed with TV conguration via the Hospital Setup Wizard, select NEXT and press OK
on the Installer Remote. Continue to “Complete the TV Conguration” below.
• To save the data entered and exit the Hospital Setup Wizard, use the arrow keys to select
DONE and then press OK on the Installer Remote. Remember, however, that if you do not complete the Hospital Setup Wizard, pillow speaker functionality will not be enabled unless you set Installer Menu item 027 HOSPITAL MODE appropriately. See the “Installer Menu” section of this document for further information.
Complete the TV Conguration
The following procedure describes the remaining steps in the Hospital Setup Wizard. You can select the “BACK” button, where available, to check previous settings, as necessary. Typically, if you do not modify the default settings, the “NEXT” button is automatically selected when you proceed forward within the Hospital Setup Wizard. Where appropriate, you can simply press OK on the Installer Remote to proceed to the next step if the default value(s) for the TV parameter(s) in question are applicable for your installation.
Note: If you choose to exit the Hospital Setup Wizard from this point on, any settings made will not be retained.
1. In the Select the Tuning Band screen, use the Up/Down arrow keys on the Installer Remote to highlight/select the appropriate tuning band option: Cable Standard (default), Cable HRC, Cable IRC, or Air. Then, press OK. When you have made your selection, use the arrow keys to select NEXT, and then press OK.
206-4344
(Continued on next page)
27
Hospital Setup Wizard (Cont.)
(Continued from previous page)
SELECT THE TUNING BAND
X
Select the tuning band you would like to use
Cable Standard
Cable HRC
Cable IRC
Air
BACK
NEXT
^
02
2. By default, all Aux inputs are enabled, as shown initially in the Enable/Disable Aux Inputs screen. To disable an Aux input, use the arrow keys on the Installer Remote to select the desired input, and then press OK to toggle the status of the Aux input.
X
ENABLE/DISABLE AUX INPUTS
Enable/disable Aux inputs as required.
AV
HDMI 1
HDMI 2
03
BACK
NEXT
Enabled Aux inputs are included in the channel lineup. If an Aux input will not be used, it is typically advisable to disable it, though you may also simply delete it from the channel lineup in step 5, if you want to leave it enabled in the Installer Menu. When you are ready to continue, use the arrow keys to select NEXT, and then press OK.
Note: After the Hospital Setup Wizard is complete (see step 7), the only way to add or remove Aux inputs to/from the FTG Channel Map created by the wizard, is to export a Clone (.tlx) file from the TV, edit the FTG Channel Map using the Cloud Configuration Tool, and then import the edited Clone file to the TV. See “Cloning Procedures” on pages 68 to 74 and/or “Cloud Conguration Tool Overview” on pages 75 to 81 for further information.
28
(Continued on next page)
206-4344
Hospital Setup Wizard (Cont.)
(Continued from previous page)
Note: Disabled Aux inputs are not included in the channel lineup. However, if you wish to enable a disabled Aux input after the Hospital Setup Wizard is complete, you may do so by changing the applicable Installer Menu settings in the Cloud Configuration Tool. See also note above.
3. In the Speaker Selection screen, you will be able to select the speaker conguration for the TV.
This selection sets Installer Menu item 027 HOSPITAL MODE, which also means that when the Hospital Setup Wizard is complete, the TV will be operating in FTG Mode via CPU with Hospital Mode features enabled. See item 027 description on page 58 for further information.
Use the arrow keys on the Installer Remote to select the appropriate speaker conguration:
• Highlight/select the desired speaker: Pillow Only (default), TV Only, or Pillow & TV. Then,
press OK.
• If applicable, select the pillow speaker code/voltage and press OK.
Note: If using a Pro:Centric pillow speaker (LG IR codes) or a pillow speaker with Zenith IR codes, make sure the “Zenith” (+12v)” pillow speaker code/voltage is selected.
When you have made your selection(s), use the arrow keys to select NEXT, and then press OK.
X
S
PEAKER SELECTION
Select the desired speaker configuration
Pillow Only
TV Only
Pillow & TV
Pillow Speaker Code/Voltage
Zenith (+12v)
Philips (+5v)
RCA (-5v)
BACK
NEXT
^
^
04
4. In the Channel Tuning screen, you have the option to initiate an automated channel scan that will search for all available digital and analog channels. Select RUN AUTO TUNING and press OK on the Installer Remote to start the channel scan.
Auto Tuning progress will be shown in a new Channel Tuning screen. The scan typically takes a few minutes. When the channel scan is complete, the Hospital Setup Wizard will automatically advance to the Edit the Channel Lineup screen. Continue with step 5.
Note: You MUST select RUN AUTO TUNING and press OK in order to run the channel scan. If you move on to the next step without running Auto Tuning, there will be no digital or analog channels in the channel lineup. In this case, upon completion of the Hospital Setup Wizard, the only channels in the resulting FTG Channel Map will be any enabled Aux inputs.
206-4344
(Continued on next page)
29
Hospital Setup Wizard (Cont.)
(Continued from previous page)
Note: If you do not want to run Auto Tuning, use the arrow keys on the Installer Remote to select SKIP and press OK.
X
CHANNEL TUNING
Do you want to scan for available channels? You MUST select RUN AUTO TUNING and press OK in order to run the channel scan. If you SKIP Auto Tuning, there will be no digital or analog channels in the channel lineup.
05
BACK
SKIP
RUN AUTO TUNING
5. In the Edit the Channel Lineup screen, you can customize the channel lineup, add channel labels and icons, etc. before the channel lineup is used to create an FTG Channel Map in step 7.
You can also set up channel banks in this screen.
Note: The total number of channels found (“Searched”) during Auto Tuning is indicated at the top left of the display. Use Up/Down scroll arrows on the screen to access options for channel banks.
X
EDIT THE CHANNEL LINEUP
Edit the channel lineup as applicable/required.
Searched channels: 135; Enabled Aux: 3; Added channels: 128; Added Aux: 3 You can add up to 600 channels (Aux added as analog).
Channel/Input
Press OK ( ) to add or delete channels.
<
Channel Label
Channel Icon
You can also use numeric keys to direct enter Icon number (0–212)
<
BACK
NEXT
DIGITAL 2-1
NO LOGO
>
>
06
>
>
30
Note: If, for any reason, you elect to re-run Auto Tuning after customizing channels in the Edit the Channel Lineup screen, your current custom channel settings will be lost, and you will need to replicate the desired customization.
(Continued on next page)
206-4344
Loading...
+ 109 hidden pages