LG 42PQ20, 42PQ30, 42PQ30C, 42PQ31, 42PQ60 Owner Manual

OWNER’S MANUAL

PLASMA TV

Please read this manual carefully before operating
your set and retain it for future reference.

42PQ20
50PQ20
42PQ30
50PQ30
42PQ31
50PQ31
42PQ60
50PQ60
50PS30
50PS60
60PS60

P/NO : SAC33575901 (1004-REV07)

42PQ30C
50PQ30C
50PS60C
60PS60C
50PS70
60PS70
50PS80
60PS80

www.lg.com

A

WARNING / CAUTION

WARNING / CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and
receiver.

- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV
technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two condi­tions: (1) This device may not cause (harmful)
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation (of the device).

Any changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product

The lightning flash with arrowhead
symbol, within an equilateral triangle, is

intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.

The exclamation point within an equilateral

triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the litera­ture accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.

1

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers)that produce
heat.

Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a
third grounding prong, The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.

Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

Only use attachments/accessories specified by
the manufacturer.

Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus com­bination to avoid injury from tip-over.

Unplug this apparatus during lighting storms
or when unused for long periods of time.

Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power­supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.

1

2

3

4

5

7

8

6

9

10

2

SAFETY INSTRUCTIONS

Never touch this apparatus or antenna during
a thunder or lighting storm.

When mounting a TV on the wall, make sure
not to install the TV by the hanging power and
signal cables on the back of the TV.

Do not allow an impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.

CAUTION concerning the Power Cord:
It is recommend that appliances be placed

upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance
and has no additional outlets or branch
circuits. Check the specification page of this
owner's manual to be certain.

Do not connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.

Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of
the appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.

Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug when
unplugging the power cord. Do not pull on the
power cord to unplug the TV.

WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product
near flammable objects such as gasoline or
candles or expose the TV to direct air
conditioning.

Do not expose to dripping or splashing and do
not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g.
on shelves above the unit).

GGRROOUUNNDDIINNGG
Ensure that you connect the earth ground wire

to prevent possible electric shock (i.e. a TV
with a three-prong grounded AC plug must be
connected to a three-prong grounded AC out­let). If grounding methods are not possible,
have a qualified electrician install a separate
circuit breaker.

Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas
pipes.

DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS
Mains plug is the disconnecting device. The

plug must remain readily operable.

"As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH"

(Except 42/50PQ30C, 50/60PS60C)

12

11

14

13

16

17

18

19

Power
Supply

Short-circuit

Breaker

15

3

AANNTTEENNNNAASS
OOuuttddoooorr aanntteennnnaa ggrroouunnddiinngg
If an outdoor antenna is installed, follow the

precautions below. An outdoor antenna system
should not be located in the vicinity of over­head power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur.

Be sure the antenna system is grounded so as
to provide some protection against voltage
surges and built-up static charges.

Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of
grounding conductors, location of antenna dis­charge unit, connection to grounding elec­trodes and requirements for the grounding
electrode.

AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee
NNaattiioonnaall EElleeccttrriiccaall CCoodde

e,, AANNSSII//NNFFPPAA 7700

CClleeaanniinngg
When cleaning, unplug the power cord and

scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners or benzene.

MMoovviinn gg
Make sure the product is turned off,

unplugged and all cables have been removed. It
may take 2 or more people to carry larger TVs.
Do not press against or put stress on the front
panel of the TV.

VVeenntt iillaattiioonn
Install your TV where there is proper ventila-

tion. Do not install in a confined space such as
a bookcase. Do not cover the product with
cloth or other materials (e.g.) plastic while
plugged in. Do not install in excessively dusty
places.

If you smell smoke or other odors coming from
the TV or hear strange sounds, unplug the power
cord contact an authorized service center.

Do not press strongly upon the panel with
hand or sharp object such as nail, pencil or
pen, or make a scratch on it.

Keep the product away from direct sunlight.

20

23

24

25

26

21

22

NEC: National Electrical Code

Équipement électrique

Pince de mise à la terre

Fil d entrée d antenne

Décharge d antenne
(section 810-20 du NEC)

Conducteur mis à la terre
(section 810-21 du NEC)

Pince de mise à la terre

Système d électrode
de mise à la terre (article 250,
section H du NEC)

4

CONTENTS

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . A

SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . 1

FEATURE OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PREPARATION

Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Stand Instruction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12

Desktop Pedestal Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Securing the TV to the wall to prevent falling
when the TV is used on a stand

. . . . . . . . . . . . . . . . . . . . . . . 14

Swivel Stand

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Antenna or Cable Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . 15

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

VCR Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Audio Out Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

USB Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24

PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Turning On TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Channel Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34

Volume Adjustment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Quick Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Channel Setup

- Auto Scan (Auto Tuning)

. . . . . . . . . . . . . . . . . . . . . . . . . . . 39

- Add / Delete Channel (Manual Tuning)

. . . . . . 40

- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

41

Channel List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Favorite Channel Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Favorite Channel List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Brief Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Input Label

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

AV Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

SIMPLINK

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

USB

Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Photo List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

51

Music List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Movie List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

DivX Registration Code

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

PICTURE CONTROL

Picture Size (Aspect Ratio) Control

. . . . . . . . . . . . . . . . . . 64

Picture Wizard

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Energy Saving

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

68

Preset Picture Settings(Picture Mode)

. . . . . . . . . . . . . . 69

Manual Picture Adjustment - User Mode

. . . . . . . . . . 70

Picture Improvement Technology

. . . . . . . . . . . . . . . . . . . . . 71

Expert Picture Control

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Image Sticking Minimization (ISM) Method

. . . . . . . 75

Demo Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

5

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 77

Clear Voice II

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Preset Sound Settings (Sound Mode)

. . . . . . . . . . . . . . 79

Sound Setting Adjustment - User Mode

. . . . . . . . . . .

80

Balance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

TV Speakers On/Off Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Audio Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Stereo/SAP Broadcasts Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . 84

Audio Language

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

On-Screen Menus Language Selection

. . . . . . . . . . . . . 86

Caption Mode

- Analog Broadcasting System Captions

. . . . . . . 87

- Digital Broadcasting System Captions

. . . . . . . . 88

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

TIME SETTING

Clock Setting

- Auto Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

- Manual Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Auto On/Off Time Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Sleep Timer Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

PARENTAL CONTROL / RATINGS

Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Downloadable Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3

External Input Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4

Key lock

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8

Product Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9

Programming The Remote Control

. . . . . . . . . . . . . . . . .

110

IR Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

113

External Control Through RS-232C

. . . . . . . . . . . . . . . . .115

6

FEATURE OF THIS TV

is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories.
“

Dolby

“and the double-D symbol are trademarks of

Dolby Laboratories.

■

When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV

for an extended period, it can become permanently imprinted on the screen. This phenomenon is known
as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.

■

In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period

(2 or more hours for LCD, 1 or more hours for Plasma).

■

Image burn can also occur on the letterboxed

areas of your TV if you use the 4:3 aspect
ratio setting for an extended period.

IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/ BURN-IN” ON YOUR TV SCREEN

High-definition television. High-resolution digital
television broadcast and playback system composed
of roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p
resolutions.

THX Cinema mode is recommended for watching
movies. Designed for use in a dark room.

(This feature is not available for all models.)

This TV contains the detailed calibrations necessary
for professional certification by the Imaging Science
Foundation. The resulting ISF “day” and “night” modes
will then be accessible by the user to experience the
best their LG HDTV has to offer.
CALIBRATE LIKE A PRO: Sophisticated and detailed
calibrations can be made through the ISFccc mode.
Detailed calibration requires a licensed technician.
Please contact your local dealer to inquire about an ISF
certified technician.

HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC."

■

This feature is not available for all models.

“DivX Certified to play DivX video, including premium

content”
ABOUT DIVX VIDEO: DivX®is a digital video format
created by DivX,Inc. This is an official DivX Certified
device that plays DivX video. Visit www.divx.com for
more information and software tools to convert your
files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified®device must be registered in order to play
DivX Video-on-Demand (VOD) content. To generate
the registration code, locate the DivX VOD section in
the device setup menu. Go to vod.divx.com with this
code to complete the registration process and learn
more about DivX VOD.

(This feature is not available for all models.)

PREPARATION

7

PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.

The accessories included may differ from the images below.

Protection Cover

(Refer to P.11)

1.5V 1.5V

Owner’s Manual Power Cord

Remote Control,

Batteries

INPUT

M

UTE

TV

PO

W

ER

Q. MENU

MENU

AV MODERETURN

ENTER

VOL

CH

123

456

78

0

9

FLASHBK

P
A

G

E

DVD

LIST

ENERGY SAVING

STB

F

R
E
E

ZE

R
A

T
IO

FAV

M
ARK

CD Manual

Bolts for stand assembly

(Refer to P.11)

x 4

Cable Holder

OOppttiioonn EExxttrraass

* Wipe spots on the exterior only with

the polishing cloth.

* Do not wipe roughly when removing

stain. Excessive pressure may cause
scratch or discoloration.

Polishing Cloth

(Not included with all models)

D-sub 15 pin Cable

When using the VGA (D-sub 15 pin
cable) PC connection, the user must
use shielded signal interface cables
with ferrite cores to maintain stan­dards compliance.

x 2

FAV

MARK

Q

.M

EN

U

MENU

LIST

123

456

78

0

9

FLASHBK

MUTE

VOL

CH

P
A
G

E

RETURN

IN

FO

ENTER

INPUT

POWER

AV MODE

ENERGY SAVING

F
R

E
EZ

E

R

A
TIO

or

(Except 60PS60, 60PS60C,

60PS70, 60PS80)

Cable management

clip

(Refer to P.12)

(Only

60PS60, 60PS60C,

50/60PS70, 50/60PS80)

Install the power plug closely.

Use of ferrite core

(Not included with all models)

Ferrite core can be used to reduce the electromagnetic wave
when connecting the power cord.
The closer the location of the ferrite core to the power plug,
the better it is.

or

Ferrite Core

PREPARATION

8

PREPARATION

FRONT PANEL INFORMATION

■

Image shown may differ from your TV.

INPUT
Button

POWER
Button

MENU
Button

ENTER
Button

VOLUME
Buttons

CHANNEL
Buttons

42/50PQ20

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates blue when the TV is switched on.

Intelligent Sensor

Adjusts picture according to the
surrounding conditions.

Remote Control Sensor

GG

When the TV cannot be turned on with the remote control, press the (power) button on the TV. (The
remote control will not work when the (power) button on the TV is switched off. )

CAUTION (Except

42/50PQ30C, 50/60PS60C)

CHANNEL
Buttons

VOLUME
Buttons

ENTER Button

MENU Button

INPUT Button

POWER Button

50/60PS70, 50/60PS80

Power/Standby Indicator

• Illuminates red in standby mode.

•

The LED is off while the TV remains on.

Remote Control Sensor
Intelligent Sensor

Adjusts picture according to
the surrounding conditions.

G

Do not step on the glass stand or subject it to any impact.It
may break, causing possible injury from fragments of glass, or
the TV may fall.

G

Do not drag the TV. The floor or the product may be damaged.

INPUT

MENU

ENTER

VOL

CH

CH

CH

VOL

VOL

ENTER

MENU

INPUT

9

INPUT
Button

MENU
Button

ENTER
Button

VOLUME
Buttons

CHANNEL
Buttons

Power/Standby Indicator

Illuminates red in standby

mode.

Illuminates blue when the TV

is switched on.

42/50PQ30, 42/50PQ31, 42/50PQ30C, 42/50PS30

Remote Control Sensor
Intelligent Sensor

Adjusts picture according to
the surrounding conditions.

POWER
Button

Power/Standby Indicator

Illuminates red in standby mode.
Illuminates white when the TV is switched on

and goes out slowly .

42/50PQ60, 50/60PS60, 50/60PS60C

CHANNEL
Buttons

VOLUME
Buttons

ENTER Button

MENU Button

INPUT Button

POWER Button

Remote Control Sensor
Intelligent Sensor

Adjusts picture according to
the surrounding conditions.

PREPARATION

INPUT

MENU

ENTER

VOL

CH

CH

CH

VOL

VOL

ENTER

MENU

INPUT

PREPARATION

10

PREPARATION

BACK PANEL INFORMATION

■

Image shown may differ from your TV.

AV IN 2

L/ MONO

R

AUDIO

VIDEO

USB IN

HDMI /

DVI IN 3

7

1

9

AV IN 2

L/ MONO

R

AUDIO

VIDEO

USB IN

HDMI/DVI IN 3

HDMI/DVI IN 4

7

1

9

Only 42/50PQ60,

50/60PS60, 50/60PS60C,

50/60PS70,

50/60PS80

R

ANTENNA/

CABLE IN

HDMI/DVI IN

2

1

RGB IN (PC)

RS-232C IN

(CONTROL & SERVICE)

OPTICAL
DIGITAL
AUDIO OUT

AUDIO IN

(RGB/DVI)

COMPONENT IN

1

2

VIDEO

AUDIO

L

R

AUDIO

AV IN 1

VIDEO

S-VIDEO

REMOTE

CONTROL IN

/MONO

1

2

HDMI/DVI IN, HDMI IN

Digital Connection. Supports HD video and Digital
audio. Doesn’t support 480i.

Accepts DVI video using an adapter or HDMI to
DVI cable (not included)

OPTICAL DIGITAL AUDIO OUT

Optical digital audio output for use with amps and
home theater systems.

Note: In standby mode, this port doesn’t work.

RS-232C IN (CONTROL & SERVICE) PORT

Used by third party devices.

AUDIO IN (RGB/DVI)

1/8” headphone jack for analog PC audio input.

RGB IN (PC)

Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).

REMOTE CONTROL IN PORT

For a wired remote control.

COMPONENT IN

Analog Connection. Supports HD.
Uses a red, green, and blue cable for video & red

and white for audio.

AV (Audio/Video) IN

Analog composite connection. Supports standard
definition video only (480i).

S-VIDEO

Better quality than standard composition.
Supports standard definition video only (480i).

ANTENNA/CABLE IN

Connect over-the air signals to this jack.
Connect cable signals to this jack.

USB IN

Used for viewing photos and listening to MP3.

Power Cord Socket

For operation with AC power.
Caution: Never attempt to operate the TV on DC

power.

1

2

3

4

5

9

10

8

6

7

3

4

5

6

7

8

10

PREPARATION

11

STAND INSTRUCTION

■

Image shown may differ from your TV.

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

Assemble the TV as shown.

1

2

Fix the 4 bolts securely using the holes in the
back of the TV.

3

Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

1

Loose the bolts from TV.

2

Detach the stand from TV.

3

After removing the stand, install the included

pprr ootteeccttiioonn ccoovveerr

over the hole for the stand.

Press the

PPRROOTTEECCTTIIOONN CCOOVVEERR

into the TV

until you hear it click.

Protection Cover

GG

When assembling the desk type stand, check
whether the bolt is fully tightened. (If not tight­ened fully, the product can tilt forward after the
product installation). If you tighten the bolt with
excessive force, the bolt can deviate from abra­sion of the tightening part of the bolt.

NOTE

!

Installation

Detachment

GG

When assembling the stand, make sure to distinguish
and assemble the front and rear side of the stand
correctly.

(Except 60PS60, 60PS60C,

60PS70, 60PS80)

FRONT

PREPARATION

12

PREPARATION

After connecting the cables as necessary, install
CABLE HOLDER as shown and bundle the
cables.

To connect additional equipment, see

EXTERNAL EQUIPMENT SETUP section.

1

Install the CABLE MANAGEMENT CLIP
as shown.

2

CABLE MANAGEMENT CLIP

GG

Hold the CABLE MANAGEMENT CLIP with both
hands and pull it upward.

CABLE HOLDER

HOW TO REMOVE THE CABLE MANAGEMENT CLIP

(Only 60PS60, 60PS60C, 50/60PS70, 50/60PS80)

(Only 60PS60, 60PS60C, 50/60PS70, 50/60PS80)

CABLE MANAGEMENT

■

Image shown may differ from your TV.

PREPARATION

13

VESA WALL MOUNTING

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact your nearest installer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.

GG

Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock.

CAUTION

GG

Screw length needed depends on the wall mount
used. For further information, refer to the instruc­tions included with the mount.

GG

Standard dimensions for wall mount kits are shown
in the table.

GG

When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.

GG

Do not use screws longer then the standard dimen­sion, as they may cause damage to the inside to
the TV.

GG

For wall mounts that do not comply with the VESA
standard screw specifications, the length of the

screws may differ depending on their specifica­tions.

GG

Do not use screws that do not comply with the
VESA standard screw specifications.

Do not use fasten the screws too strongly, this may
damage the TV or cause the TV to a fall, leading to
personal injury. LG is not liable for these kinds of
accidents.

GG

LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installa­tion instructions.

NOTE

!

DESKTOP PEDESTAL INSTALLATION

For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.

■

Image shown may differ from your TV.

4 inches

4 inches

4 inches

4 inches

GG

Ensure adequate ventilation by following
the clearance recommendations.

GG

Do not mount near or above any type
of heat source.

CAUTION

Model

VESA (A *B)

Standard Screw Quantity

Wall Mounting

bracket

(sold separately)

42PQ20, 42PQ30,

42PQ31, 42PQ30C,

42PQ60,

50PQ20, 50PQ30,

50PQ31, 50PQ30C,

50PQ60, 50PS30,

50PS60, 50PS60C,

50PS70, 50PS80

60PS60, 60PS60C,

60PS70, 60PS80

400* 400 M6 4

600* 400 M8 4

AW-50PG60MS

AW-60PG60MS

AA

BB

PREPARATION

14

PREPARATION

SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is
mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope (sold separately) to tie the product. It is safer to tie
the rope so it becomes horizontal between the wall and the product.

■

You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).

■

Image shown may differ from your TV.

GG

Use a platform or cabinet strong enough and large enough to support
the size and weight of the TV.

GG

To use the TV safely, make sure that the height of the bracket on the
wall and the one on the TV are the same.

NOTE

!

SWIVEL STAND

(This feature is not available for all models.)

After installing the TV, you can adjust the TV manually to the left or right direction by 20 degrees to suit your
viewing position.

PREPARATION

15

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connection.

For optimum picture quality, adjust antenna direction if needed.

2. Cable

Wall
Antenna
Socket

Outdoor
Antenna
(VHF, UHF)

Cable TV
Wall Jack

Multi-family Dwellings/Apartments
(Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)

Be careful not to bend the copper wire
when connecting the antenna.

Copper Wire

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

ANTENNA/

CABLE IN

R

ANTENNA/

CABLE IN

R

■

To prevent damage do not connect to the power outlet until all connections are made between the devices.

EXTERNAL EQUIPMENT SETUP

16

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do
receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

Component Connection

1. How to connect

Connect the video outputs (Y, PB, PR

)

of the digital set-

top box to the

CCOOMMPPOONNEENNTT IINN VVIIDD EEOO 11

jacks on

the TV. Match the jack colors (Y = green, P

B = blue, and

P

R = red).

Connect the audio output of the digital set-top box to
the

CCOOMMPPOONNEENNTT IINN AAUUDDIIOO 11

jacks on the TV.

2

1

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box. operation

)

■

Select the

CCoommpp oonn eenntt 11

input source on the TV using the

IINNPPUU TT

button on the remote control.

■

If connected to

CCOOMMPPOONNEENNTT IINN 22

input, select the

CCoommpp oonn eenntt 22

input source on the TV.

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

■

Image shown may differ from your TV.

AN

CA

RGB IN (PC)

AUDIO

VIDEO

S-VIDEO

REMOTE

CONTROL IN

/MONO

COMPONENT IN

1

2

VIDEO

AUDIO

L

R

AV IN 1

Y L RPB PR

1

2

Y, CB/PB, CR/PR

Supported Resolutions

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

15.73 59.94

15.73 60.00

31.47 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

27.00 24.00

33.75 30.00

67.43 59.94

67.50 60.00

Resolution

720x480i

720x480p

1280x720p

1920x1080i

1920x1080p

Signal

480i
480p
720p

10 8 0 i

10 8 0 p

Component

Yes
Yes
Yes
Yes
Yes

HDMI

No
Yes
Yes
Yes
Yes

EXTERNAL EQUIPMENT SETUP

17

HDMI Connection

Connect the digital set-top box to

HHDDMMII//DD VVII IINN 11

,

22, 33

or

44

(Only 42/50PQ60, 50/60PS60,

50/60PS60C,

50/60PS70, 50/60PS80

) jack on the

TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Turn on the digital set-top box.
(

Refer to the owner’s manual for the digital set-top box.

)

■

Select the

HHDDMMII11, 22, 33

or

44

(Only 42/50PQ60, 50/60PS60,

50/60PS60C,

50/60PS70, 50/60PS80

) input source on the

TV using the

IINNPPUUTT

button on the remote control.

2

1

HDMI-DTV

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.469 59.94

31.50 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

27.00 24.00

33.75 30.00

67.43 59.94

67.50 60.00

Resolution

720x480p

1280x720p

1920x1080i

1920x1080p

HDMI/DVI IN

2

1

HDMI-DTV OUTPUT

RGB(PC)

RS-232C IN

(CONTROL & SERVICE)

OPTICAL
DIGITAL
AUDIO OUT

AUDIO

(RGB/DVI)

R

CO

1

GG

Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version

1.3, it can cause flickers or no screen display. In
this case use the latest cables that support HDMI
version 1.3.

NOTE

!

EXTERNAL EQUIPMENT SETUP

18

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

HDMI/DVI IN

2

1

RGB IN (PC)

RS-232C IN

(CONTROL & SERVICE)

OPTICAL
DIGITAL
AUDIO OUT

REMOTE

CONTROL IN

AV IN 1

AUDIO IN

(RGB/DVI)

LR

DVI-DTV OUTPUT

1

2

GG

A DVI to HDMI cable or adapter is required for this
connection. DVI doesn't support audio, so a separate
audio connection is necessary.

NOTE

!

Connect the DVI output of the digital set-top box to the
HHDDMMII//DDVVII IINN 11, 22, 33 or44

(Only 42/50PQ60,

50/60PS60, 50/60PS60C,

50/60PS70, 50/60PS80

)

jack on the TV.

Connect the audio output of the digital set-top box to
the

AAUUDDIIOO IINN ((RRGGBB//DDVVII))

jack on the TV.

1. How to connect

2. How to use

■

Turn on the digital set-top box. (Refer to the owner’s man­ual for the digital set-top box.

)

■

Select the

HHDDMMII11, 22, 33

or

44

(Only 42/50PQ60,

50/60PS60, 50/60PS60C,

50/60PS70, 50/60PS80

)

input source on the TV using the

IINNPPUUTT

button on the

remote control.

2

1

EXTERNAL EQUIPMENT SETUP

19

DVD SETUP

Component Connection

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

YPBP

R

Video output ports

on DVD player

Y

Y

Y

Y

PB

B-Y

Cb

Pb

PR

R-Y

Cr

Pr

Connect the video outputs (Y, PB

, PR

)

of the DVD to the

CCOOMM PPOONNEENNTT IINN VVIIDD EEOO 11

jacks on the TV.

Match the jack colors (Y = green, P

B = blue, and PR = red

)

.

Connect the audio outputs of the DVD to the
CCOOMM PPOONNEENNTT IINN AAUUDDIIOO 11

jacks on the TV.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

CCoommpp oonneenn tt11

input source on the TV using

the

IINNPPUU TT

button on the remote control.

■

If connected to

CCOOMMPPOONNEENNTT IINN 22

input, select the

CCoommpp oonn eenntt 22

input source on the TV.

■

Refer to the DVD player's manual for operating instructions.

2

1

RGB(PC)

AUDIO

VIDEO

S-VIDEO

REMOTE

CONTROL IN

/MONO

COMPONENT IN

1

2

VIDEO

AUDIO

L

R

AV IN 1

Y L RPB PR

1 2

EXTERNAL EQUIPMENT SETUP

20

EXTERNAL EQUIPMENT SETUP

S-Video Connection

HDMI Connection

Connect the HDMI output of the DVD to the
HHDDMMII//DDVVII IINN 11, 22, 33

or

44

(Only 42/50PQ60,

50/60PS60, 50/60PS60C,

50/60PS70, 50/60PS80

)

jack on the TV.

No separate audio connection is necessary.
HDMI supports both audio and video.

1. How to connect

2. How to use

■

Select the

HHDDMMII11, 22, 33

or

44

(Only 42/50PQ60,

50/60PS60, 50/60PS60C,

50/60PS70, 50/60PS80

)

input source on the TV using the

IINNPPUU TT

button on the

remote control.

■

Refer to the DVD player's manual for operating instructions.

2

1

1

2

VIDEO

AUDIO

L

R

REMOTE

AN

CA

COMPONENT IN

L R

S-VIDEO

AUDIO

AUDIO

AV IN 1

S-VIDEO

/MONO

VIDEO

1

2

HDMI/DVI IN

2

1

(CONTROL & SERVICE)

HDMI-DVD OUTPUT

1

Connect the S-VIDEO output of the DVD to the
SS --VVIIDD EE OO

input on the TV.

Connect the audio outputs of the DVD to the

AAUUDDIIOO

input jacks on the TV.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select the

AAVV11

input source on the TV using the

IINNPPUU TT

button on the remote control.

■

Refer to the DVD player's manual for operating instructions.

2

1

EXTERNAL EQUIPMENT SETUP

21

VCR SETUP

Antenna Connection

ANTENNA/

CABLE IN

L R

S-VIDEO VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

Wall Jack

Antenna

1

2

Connect the RF antenna out socket of the
VCR to the

AANNTTEENNNNAA//CCAABBLLEE IINN

socket

on the TV.

Connect the antenna cable to the RF
antenna in socket of the VCR.

1. How to connect

2. How to use

■

Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.

■

Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.

)

2

1

EXTERNAL EQUIPMENT SETUP

22

EXTERNAL EQUIPMENT SETUP

Composite (RCA) Connection

Connect the

AAUUDDIIOO/VVIIDDEEOO

jacks between TV and
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.

)

■

Select the

AAVV11

input source on the TV using the

IINNPPUU TT

button on the remote control.

■

If connected to

AAVV IINN 22

, select

AAVV22

input source on the

TV.

1

2. How to use

■

Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.

)

■

Select the

AAVV11

input source on the TV using the

IINNPPUU TT

button on the remote control.

GG

If you have a mono VCR, connect the audio cable
from the VCR to the

AAUUDDIIOO LL//MMOONNOO

jack of the

TV.

NOTE

!

1

2

VIDEO

AUDIO

L

R

RGB IN (PC)

REMOTE

CONTROL IN

ANTE

CAB

S-VIDEO

COMPONENT IN

AUDIO

AV IN 1

VIDEO

/MONO

L R

S-VIDEO VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

1

S-Video Connection

Connect the S-VIDEO output of the VCR to the
SS --VVIIDDEEOO

input on the TV.

Connect the audio outputs of the VCR to the

AAUUDDIIOO

input jacks on the TV.

1. How to connect

2

1

1

2

VIDEO

AUDIO

L

R

RGB IN (PC)

REMOTE

CONTROL IN

ANTENN

CABLE

COMPONENT IN

AUDIO

AV IN 1

S-VIDEO

/MONO

VIDEO

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

1

2

GG

Do not connect to both Video
and S-Video at the same time. In
the event that you connect both
Video and the S-Video cables,
only the S-Video will work.

CAUTION

GG

S-Video provides better quality than composite. Use
it when available.

NOTE

!

EXTERNAL EQUIPMENT SETUP

23

OTHER A/V SOURCE SETUP

AUDIO OUT CONNECTION

L R

VIDEO

AV IN 2

L/ MONO

R

AUDIO

VIDEO

USB IN

HDMI IN 3

Camcorder

Video Game Set

Connect the

AAUUDDIIOO/VVIIDDEEOO

jacks
between TV and external equipment.
Match the jack colors

.

(

Video = yellow, Audio Left = white, and

Audio Right = red

)

1. How to connect

2. How to use

■

Select the

AAVV22

input source on the TV using

the

IINNPPUU TT

button on the remote control.

■

If connected to

AAVV II NN 11

input, select the

AAVV11

input source on the TV.

■

Operate the corresponding external equipment.

1

1

RGB(PC)

RS-232C IN

(CONTROL & SERVICE)

OPTICAL
DIGITAL
AUDIO OUT

AUDIO

(RGB/DVI)

C

HDMI/DVI IN

2

1

1

2

GG

When connecting with external audio equipment, such as
amplifiers or speakers, you can turn the TV speakers off in
the menu. (

GG

pp..8822

)

NOTE

!

G

Do not look into the optical output port. Looking at the laser beam may damage your vision.

GG

Audio with ACP (Audio Copy Protection) function may block digital audio output.

CAUTION

Connect one end of the optical cable to the TV’s

OOPPTTIICCAALL

port of

DDIIGGIITTAALL AAUUDDIIOO OOUUTT

.

Connect the other end of the optical cable to the digital
audio input on the audio equipment.

Set the “TV Speaker option - Off” in the AUDIO menu. (

GG

pp..

8822

).
See the external audio equipment instruction manual for
operation.

1. How to connect

2

3

1

Send the TV’s audio to external audio equipment via the Audio Output port.

EXTERNAL EQUIPMENT SETUP

24

EXTERNAL EQUIPMENT SETUP

USB CONNECTION

AV IN 2

L/ MONO

R

AUDIO

VIDEO

USB IN

HDMI /

DVI IN 3

Connect the USB device to the

UUSSBB IINN

jack on the side

of TV.

1. How to connect

1

2. How to use

■

After connecting the

UUSSBB IINN

jack, you use the USB func-

tion. (

GG

pp..5500

)

1

i.e)

EXTERNAL EQUIPMENT SETUP

25

PC SETUP

DVI to HDMI Connection

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

VGA (D-Sub 15 pin) Connection

VID

RS-232C IN

(CONTROL & SERVICE)

OPTICAL
DIGITAL
AUDIO OUT

REMOTE

CONTROL IN

S-VID

AV IN 1

C

RGB IN (PC)

AUDIO IN

(RGB/DVI)

AUDIO

RGB OUTPUT

1

2

RGB IN (PC)

RS-232C IN

(CONTROL & SERVICE)

OPTICAL
DIGITAL
AUDIO OUT

REMOT

CONTROL

AUDIO IN

(RGB/DVI)

HDMI/DVI IN

2

1

DVI-PC OUTPUT AUDIO

1

2

2. How to use

■

Turn on the PC and the TV.

■

Select the

RRGGBB--PPCC

input source on the TV using the

IINNPPUU TT

button on the remote control.

Connect the VGA output of the PC to the

RRGGBB II NN

((

PP CC

))

jack on the TV.

Connect the PC audio output to the

AAUUDDIIOO IINN

((

RRGGBB//DDVVII

))

jack on the TV.

1. How to connect

2

1

2. How to use

■

Turn on the PC and the TV.

■

Select the

HHDDMMII11, 22, 33

or

44

(Only 42/50PQ60,

50/60PS60, 50/60PS60C,

50/60PS70, 50/60PS80

)

input source on the TV using the

IINNPPUU TT

button on the

remote control.

Connect the DVI output of the PC to the

HHDDMMII//DDVVII

IINN 11, 22, 33

or

44

(Only 42/50PQ60, 50/60PS60,

50/60PS60C,

50/60PS70, 50/60PS80

) jack on the TV.

Connect the PC audio output to the

AAUUDDIIOO II NN

((RRGGBB//DD VVII))

jack on the TV.

1. How to connect

2

1

EXTERNAL EQUIPMENT SETUP

26

EXTERNAL EQUIPMENT SETUP

GG

42/50PQ20, 42/50PQ30, 42/50PQ31,
42/50PQ30C, 42/50PQ60: To get the the
best picture quality, adjust the PC graphics
card to 1360x768.

GG

50PS30, 50/60PS60, 50/60PS60C,
50/60PS70, 50/60PS80

: To get the the best
picture quality, adjust the PC graphics card to
1920x1080.

GG

Depending on the graphics card, DOS mode
may not work if a HDMI to DVI Cable is in use.

GG

In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change the
PC output to another resolution, change the
refresh rate to another rate or adjust the
brightness and contrast on the PICTURE menu
until the picture is clear.

GG

Avoid keeping a fixed image on the screen for a
long period of time. The fixed image could
become permanently imprinted on the screen.

GG

The synchronization input form for Horizontal
and Vertical frequencies is separate.

GG

Depending on the graphics card, some resolu­tion settings may not allow the image to be

NOTES

!

Supported Display Specifications
(RGB-PC, HDMI-PC)

Resolution

720x400

1360x768

640x480

800x600

1024x768

1920x1080

1280x768

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.468 70.08

31.469 59.94

37.879 60.31

48.363 60.00

47.78 59.87

47.72 59.80

66.647 59.988

EXTERNAL EQUIPMENT SETUP

27

Auto Configure

Automatically adjusts picture position and minimizes
image instability. After adjustment, if the image is still
not correct, try using the manual settings or a differ­ent resolution or refresh rate on the PC.

Select

SSccrreeeenn ((RRGGBB--PPCC))

.

Select

AAuuttoo ccoo nnffiigg..

.

Auto config.

G

Resolution

Position

Size

Phase

Reset

Screen

Move

To Set

3

2

ENTER

ENTER

Select

YYeess

.

4

ENTER

Start Auto Configuration.

5

ENTER

Select

PPIICCTTUURR EE

.

1

MENU

• If the position of the image is still not correct, try Auto adjustment again.

• If picture needs to be adjusted again after Auto adjustment in RGB-PC, you can adjust the

PPoossiittiioonn, SSiizzee

or

PPhhaassee

.

Yes No

Screen Setup for PC mode

Selecting Resolution

You can choose the resolution in RGB-PC mode.
The

PPoossiittiioonn, PPhhaassee

, and

SSiizzee

can also be adjusted.

Select

PPIICCTTUURR EE

.

Select

SSccrreeeenn ((RRGGBB--PPCC))

.

Select

RReessoolluuttiioonn

.

Select the desired resolution.

1024 x 768
1280 x 768
1360 x 768

Auto config.

Resolution

G

Position

Size

Phase

Reset

Screen

Move

Prev.

1

MENU

3

4

2

ENTER

ENTER

ENTER

5

ENTER

Enter

Move

PICTURE

Picture Mode : Standard

• Contrast 90

• Brightness 50

• Sharpness 60

• Color 60

• Tint 0

• Advanced Control

• Reset

Screen (RGB-PC)

RG

E

MENU

Prev.

MENU

EXTERNAL EQUIPMENT SETUP

28

EXTERNAL EQUIPMENT SETUP

Adjustment for screen Position, Size, and Phase

If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture
phase manually.

This feature operates only in RGB-PC mode.

Select

PPoossiittiioonn, SSiizzee

, or

PPhhaassee

.

Make appropriate adjustments.

Auto config.

Resolution

Position

G

Size

Phase

Reset

GF

D

E

Screen

Move

3

ENTER

4

ENTER

■

PPoossiittiioonn

: This function is to adjust pic­ture to left/right and up/down as you
prefer.

■

SSiizzee

: This function is to minimize any
vertical bars or stripes visible on the
screen background. And the horizontal
screen size will also change.

■

PP hh aassee

: This function allows you to
remove any horizontal noise and clear or
sharpen the image of characters.

Select

PPIICCTTUURR EE

.

Select

SSccrreeeenn ((RRGGBB--PPCC))

.

1

MENU

2

ENTER

Enter

Move

PICTURE

Picture Mode : Standard

• Contrast 90

• Brightness 50

• Sharpness 60

• Color 60

• Tint 0

• Advanced Control

• Reset

Screen (RGB-PC)

RG

E

5

ENTER

Prev.

MENU