LG 42PJ350 User Manual [en, es, fr]

OWNER’S MANUAL
PLASMA TV
Please read this manual carefully before operating your set and retain it for future reference.
42PJ250 50PJ250 50PK250 60PK250 60PK280 60PK290
P/NO : SAC34173302 (1007-REV03)
42PJ340 50PJ340 42PJ350 50PJ350
50PK350 50PK340 50PK540 60PK540
42PJ550 50PJ550 50PK550 60PK550
42PJ350C 50PJ350C 50PK550C 60PK550C
www.lg.com
2

WARNING / CAUTION

WARNING / CAUTION
To prevent fire or shock hazards, do not expose this product to rain or moisture.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two condi­tions: (1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (of the device).
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera­ture accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
3
IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not use this apparatus near water.
Clean only with soft dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus com­bination to avoid injury from tip-over.
Unplug this apparatus during lighting storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power­supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
1
2
3
4
5
7
8
6
9
10
4
SAFETY INSTRUCTIONS
Never touch this apparatus or antenna during a thunder or lighting storm.
When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.
Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something.
CAUTION concerning the Power Cord: It is recommend that appliances be placed
upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.
Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
GGRROOUUNNDDIINNGG Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC out­let). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS Mains plug is the disconnecting device. The
plug must remain readily operable.
"As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH"
12
11
14
13
16
17
18
19
Power Supply
Short-circuit
Breaker
15
5
AANNTTEENNNNAASS OOuuttddoooorr aanntteennnnaa ggrroouunnddiinngg If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system should not be located in the vicinity of over­head power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna dis­charge unit, connection to grounding elec­trodes and requirements for the grounding electrode.
AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700
CClleeaanniinngg When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
MMoo vviinn gg Make sure the product is turned off,
unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV.
VVeennttiillaa ttiioonn Install your TV where there is proper ventila-
tion. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places.
Take care not to touch the ventilation open­ings. When watching the TV for a long period, the ventilation openings may become hot.
If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center.
Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it. Do not allow a impact shock onto the panel.
Keep the product away from direct sunlight.
DDoott DDeeffeecctt
The Plasma or LCD panel is a high technology
product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you’reviewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.
GGeenn eerraatteedd SSoouunndd “Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is gener­ated by plastic thermal contraction due to temperature and humidity. This noise is com­mon for products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product.This generat­ed sound does not affect the performance and reliability of the product.
20
23
24
25
26
21
22
27
NEC: National Electrical Code
28
29
6

CONTENTS

WARNING / CAUTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY INSTRUCTIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . 3
FEATURE OF THIS TV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PREPARATION
Accessories
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Stand Instruction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
Desktop Pedestal Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Swivel Stand
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VESA Wall Mounting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Securing the TV to the wall to prevent falling
when the TV is used on a stand . . . . . . . . . . . . . . . . . . . . . . . 20
Antenna or Cable Connection
. . . . . . . . . . . . . . . . . . . . . . . . . . 21
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
VCR Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
USB Connection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Audio Out Connection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PC Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
WATCHING TV / CHANNEL CONTROL
Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Turning On TV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Channel Selection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
Volume Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Quick Menu
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Channel Setup
- Auto Scan (Auto Tuning)
. . . . . . . . . . . . . . . . . . . . . . . . . . .43
- Add / Delete Channel (Manual Tuning)
. . . . . . 44
- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
Channel List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Favorite Channel Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Favorite Channel List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Brief Information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Input Label
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
AV Mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
SIMPLINK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
USB
Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Photo List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
Music List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 64
Picture Wizard
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Energy Saving
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Preset Picture Settings(Picture Mode)
. . . . . . . . . . . . . . 69
Manual Picture Adjustment - User Mode
. . . . . . . . . . 70
Picture Improvement Technology
. . . . . . . . . . . . . . . . . . . . . 71
Expert Picture Control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Picture Reset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Demo Mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Image Sticking Minimization (ISM) Method
. . . . . . . 75
7
SOUND & LANGUAGE CONTROL
Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 76
Clear Voice II
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Preset Sound Settings (Sound Mode)
. . . . . . . . . . . . . . . 78
Sound Setting Adjustment - User Mode
. . . . . . . . . . .
79
Balance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
TV Speakers On/Off Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Audio Reset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Stereo/SAP Broadcasts Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . 84
Audio Language
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
On-Screen Menus Language Selection
. . . . . . . . . . . . . 86
Caption Mode
- Analog Broadcasting System Captions
. . . . . . . 87
- Digital Broadcasting System Captions
. . . . . . . . 88
- Caption Option
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
TIME SETTING
Clock Setting
- Auto Clock Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
- Manual Clock Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Auto On/Off Time Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Sleep Timer Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Downloadable Rating
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
External Input Blocking
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4
Key lock
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5
APPENDIX
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 6
Maintenance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 8
Product Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9
IR Codes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
External Control Through RS-232C
. . . . . . . . . . . . . . . . .114
8

FEATURE OF THIS TV

Manufactured under license from Dolby Laboratories. “
Dolby
“and the double-D symbol are trademarks of
Dolby Laboratories.
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV
for an extended period, it can become permanently imprinted on the screen. This phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period
(2 or more hours for LCD, 1 or more hours for Plasma).
Image burn can also occur on the letterboxed
areas of your TV if you use the 4:3 aspect ratio setting for an extended period.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN / BURN-IN” ON YOUR TV SCREEN
High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."
This feature is not available for all models.
This TV contains the detailed calibrations necessary for professional certification by the Imaging Science Foundation. The resulting ISF “day” and “night” modes will then be accessible by the user to experience the best their LG HDTV has to offer. Sophisticated and detailed calibrations can be made through the ISFccc mode. Detailed calibration requires a licensed technician. Please contact your local dealer to inquire about an ISF certified technician.
AV Mode is three preset picture and audio settings. It allows the viewer to quickly switch between common settings. It includes Cinema, Sports, and Game Modes.
Displays HDTV programs in full 1920 x 1080p resolu­tion for a more detailed picture.
Automatically enhances and amplifies the sound of human voice frequency range to help keep dialogue audible when background noise swells.
Unlike other sensors which can only sense brightness of ambient light, LG’s “Intelligent Sensor” uses 4,096 sensing steps to evaluate its surroundings. Using a sophisticated algorithm, the LG processes picture quality elements including brightness, contrast, color, sharpness and white balance. The result is a picture optimized for it’s surroundings, more pleasing to watch and which can also save up to 50% in power consumption.
View videos and photos and listen to music on your TV through USB 2.0 (‘videos’ dependent on model).

PREPARATION

9
PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.
The accessories included may differ from the images below.
Protection Cover
(Refer to P.16)
1.5V 1.5V
Owner’s Manual Power Cord
Remote Control,
Batteries
E N
E R G
Y
CHVOL
O N /
O F
F
123
45
0
6
789
LIST
F L
A SH
B K
M A
R K
F R
E E
Z E
S A
V IN G
TV
A
V M
O D
E
IN P
U T
F A
V
R
A
T
IO
M
E
N
U
IN
F O
Q .M
E
N
U
BACK
E
X
IT
E
N
T
E
R
MUTE
P
A G E
CD Manual
Bolts for stand assembly
(Refer to P.15)
x 4
Cable Holder
OOppttiioonn EExxttrraass
* Wipe spots on the exterior only with
the polishing cloth.
* Do not wipe roughly when removing
stain. Excessive pressure may cause scratch or discoloration.
Polishing Cloth
(Not included with all models)
D-sub 15 pin Cable
When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain stan­dards compliance.
x 2
E N
E R
G Y
CHVOL
123
45
0
6
789
LIST
F
L
A S
H B
K
M A R
K
F R
E E
Z E
S A
V IN
G
TV
A V M
O
D E
IN P
U T
F
A
V
R
A T
IO
M E
N U
IN
F
O
Q
. M E
N
U
E X
I
T
E
N
T
E
R
M UTE
BACK
P
A G E
or
x 3
M4x28
M5x14
(Except 60PK250, 60PK540, 60PK550, 60PK280, 60PK290, 60PK550C)
Ferrite Core
(Black)
(This feature is not
available for all
models.)
close to the wall plug.
Ferrite core can be used to reduce the elec­tromagnetic waves that may interfere with the TV. Install the Ferrite core on the power cable close to the wall plug.
The ferrite core can be used to reduce the electromag­netic waves in the PC Audio cable. Wind the PC Audio cable on the ferrite core twice, and then plug the cables into the TV as shown in the fol­lowing picture. Place the ferrite core close to AUDIO IN(RGB/DVI) jack on the display.
Place the ferrite core close to
AUDIO IN(RGB/DVI) jack on the display.
Ferrite Core
(Gray)
(This feature is not
available for all
models.)
AUDIO IN
(RGB/DVI)
PREPARATION
10

FRONT PANEL INFORMATION

PREPARATION
Image shown may differ from your TV.
50/60PK550, 50/60PK540, 42/50PJ550, 50/60PK550C
CH
VOL
ENTER
POWER Button
INPUT Button
MENU Button
ENTER Button
VOLUME Buttons
Power/Standby Indicator
Illuminates red in standby
mode.
The LED is off while the TV
remains on.
Intelligent Sensor
Adjusts picture according to the surrounding conditions.
CHANNEL Buttons
Remote Control Sensor
You can operate the button just by touching the button lightly with your finger.
ENTER
VOL
CH
11
PREPARATION
50/60PK250, 42/50PJ250, 60PK280, 60PK290
CH
VOL
ENTER
POWER Button
INPUT Button
MENU Button
ENTER Button
VOLUME Buttons
Power/Standby Indicator
Illuminates red in standby
mode.
The LED is off while the TV
remains on.
Intelligent Sensor
Adjusts picture according to the surrounding conditions.
CHANNEL Buttons
Remote Control Sensor
You can operate the button just by touching the button lightly with your finger.
ENTER
VOL
CH
PREPARATION
12
PREPARATION
CH
VOL
ENTER
POWER Button
INPUT Button
MENU Button
ENTER
Button
VOLUME Buttons
Power/Standby Indicator
Illuminates red in standby
mode.
The LED is off while the TV
remains on.
42/50PJ350, 42/50PJ340, 50PK340, 50PK350, 42/50PJ350C
Intelligent Sensor
Adjusts picture according to the surrounding conditions.
CHANNEL Buttons
G
Do not step on the glass stand or subject it to any impact.It may break, causing possible injury from fragments of glass, or the TV may fall.
G
Do not drag the TV. The floor or the product may be damaged.
Remote Control Sensor
You can operate the button just by touching the button lightly with your finger.
ENTER
VOL
CH
PREPARATION
13
Image shown may differ from your TV.

BACK PANEL INFORMATION

AV IN 2
L/ MONO
R
AUDIO
VIDEO
SERVICE
ONLY
HDMI IN 3
7
1
9
R
ANTENNA
/CABLE
IN
HDMI/DVI IN
2
1
RGB IN (PC)
RS-232C IN
(CONTROL & SERVICE)
OPTICAL DIGITAL AUDIO OUT
AUDIO IN
(RGB/DVI)
COMPONENT IN
1
2
VIDEO
AUDIO
L
R
REMOTE
CONTROL IN
AV IN 1
AUDIO
VIDEO
/MONO
1
2
3
4
5
7
8
10
6
42/50PJ250, 50/60PK250, 60PK280, 42/50PJ340,
50/60PK540, 50PK340
HDMI/DVI IN
Digital Connection. Supports HD video and Digital audio. Doesn’t support 480i.
Accepts DVI video using an adapter or HDMI to DVI cable (not included)
OPTICAL DIGITAL AUDIO OUT
Optical digital audio output for use with amps and home theater systems.
Note: In standby mode, this port doesn’t work.
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices.
AUDIO IN (RGB)
1/8” headphone jack for analog PC audio input.
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable).
REMOTE CONTROL IN PORT
For a wired remote control.
COMPONENT IN
Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red
and white for audio.
AV (Audio/Video) IN
Analog composite connection. Supports standard definition video only (480i).
ANTENNA/CABLE IN
Connect over-the air signals to this jack. Connect cable signals to this jack.
SERVICE ONLY
Used for software updates.
Power Cord Socket
For operation with AC power. Caution: Never attempt to operate the TV on DC
power.
1
2
3
4
5
9
10
8
6
7
PREPARATION
14
PREPARATION
AV IN 2
L/ MONO
R
AUDIO
VIDEO
USB IN
HDMI IN 3
7
1
9
R
ANTENNA
/CABLE
IN
HDMI/DVI IN
2
1
RGB IN (PC)
RS-232C IN
(CONTROL & SERVICE)
OPTICAL DIGITAL AUDIO OUT
AUDIO IN
(RGB/DVI)
COMPONENT IN
1
2
VIDEO
AUDIO
L
R
REMOTE
CONTROL IN
AV IN 1
AUDIO
VIDEO
/MONO
1
2
HDMI/DVI IN
Digital Connection. Supports HD video and Digital audio. Doesn’t support 480i.
Accepts DVI video using an adapter or HDMI to DVI cable (not included)
OPTICAL DIGITAL AUDIO OUT
Optical digital audio output for use with amps and home theater systems.
Note: In standby mode, this port doesn’t work.
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices.
AUDIO IN (RGB)
1/8” headphone jack for analog PC audio input.
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable).
REMOTE CONTROL IN PORT
For a wired remote control.
COMPONENT IN
Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red
and white for audio.
AV (Audio/Video) IN
Analog composite connection. Supports standard definition video only (480i).
ANTENNA/CABLE IN
Connect over-the air signals to this jack. Connect cable signals to this jack.
USB IN
Used for viewing photos and listening to MP3.
Power Cord Socket
For operation with AC power. Caution: Never attempt to operate the TV on DC
power.
1
2
3
4
5
9
10
8
6
7
3
4
5
7
8
10
6
42/50PJ350, 50PK350, 50/60PK550, 42/50PJ550, 60PK290,
42/50PJ350C, 50/60PK550C
PREPARATION
15

STAND INSTRUCTION

Image shown may differ from your TV.
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the parts of the Stand Body with the Stand Base of the TV.
1
2
Assemble the TV as shown.
3
Installation
(Except 60PK250, 60PK540, 60PK550, 60PK280, 60PK290, 60PK550C)
Fix the 4 bolts securely using the holes in the back of the TV.
4
Stand Body
Stand Base
M4x28
M5x14
x 3
x 4
PREPARATION
16
PREPARATION
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
1
Loose the bolts from TV.
2
Detach the stand from TV.
3
After removing the stand, install the included pprrootteeccttiioonn ccoovveerr
over the hole for the stand.
Press the
PPRROOTTEECCTTIIOONN CCOOVVEERR
into the TV
until you hear it click.
Protection Cover
Detachment
PROTECTION COVER (Fix a Guide to the Outsides.)
M4x28
x 4
M4x30
x 5
(60PK250, 60PK540, 60PK550, 60PK280, 60PK290, 60PK550C)
(42/50PJ250, 50PK250, 42/50PJ340, 42/50PJ350, 50PK350, 50PK340, 50PK540, 42/50PJ550, 50PK550
,
42/50PJ350C, 50PK550C
)
PREPARATION
17

CABLE MANAGEMENT

After connecting the cables as necessary, install CABLE HOLDER as shown and bundle the cables. To connect additional equipment, see EXTERNAL EQUIPMENT SETUP section.
1
CABLE HOLDER
Image shown may differ from your TV.
PREPARATION
18

DESKTOP PEDESTAL INSTALLATION

PREPARATION
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
Image shown may differ from your TV.
4 inches
4 inches
4 inches
4 inches
GG
Ensure adequate ventilation by following the clearance recommendations.
GG
Do not mount near or above any type of heat source.
CAUTION

SWIVEL STAND

(This feature is not available for all models.)
After installing the TV, you can adjust the TV manually to the left or right direction by 20 degrees to suit your viewing position.
PREPARATION
19

VESA WALL MOUNTING

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer.
GG
Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock.
CAUTION
GG
Screw length needed depends on the wall mount used. For further information, refer to the instruc­tions included with the mount.
GG
Standard dimensions for wall mount kits are shown in the table.
GG
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
GG
Do not use screws longer then the standard dimen­sion, as they may cause damage to the inside to the TV.
GG
For wall mounts that do not comply with the VESA standard screw specifications, the length of the
screws may differ depending on their specifica­tions.
GG
Do not use screws that do not comply with the VESA standard screw specifications.
Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents.
GG
LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installa­tion instructions.
NOTE
!
Model
VESA (A *B)
Standard Screw Quantity
Wall Mounting
bracket
(sold separately)
50PK550,
42/50PJ340
42/50PJ350,
42/50PJ250
50PK250, 50PK340, 50PK350, 50PK540,
42/50PJ550
,
42/50PJ350C,
50PK550C
400* 400 M6 4
PSW400B,
PSW400BG
60PK550, 60PK250, 60PK280, 60PK290, 50PK540,
60PK550C
600* 400 M8 4
PSW600B,
PSW600BG
AA
BB

PREPARATION
20
PREPARATION

SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
Use a sturdy rope (sold separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).
Image shown may differ from your TV.
GG
Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
GG
To use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are the same.
NOTE
!
PREPARATION
21

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection.
For optimum picture quality, adjust antenna direction if needed.
2. Cable
Cable TV Wall Jack
RF Coaxial Wire (75 ohm)
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
If the antenna is not installed properly, contact your dealer for assistance.
To prevent damage do not connect to the power outlet until all connections are made between the devices.
Wall Antenna Socket
Outdoor Antenna (VHF, UHF)
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Be careful not to bend the copper wire when connecting the antenna.
Copper Wire
R
ANTENNA
/CABLE
IN
R
ANTENNA
/CABLE
IN

EXTERNAL EQUIPMENT SETUP

22
EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
Component Connection
1. How to connect
Connect the video outputs (Y, PB, PR
)
of the digital set-
top box to the
CCOOMMPPOONNEENNTT IINN VVIIDD EEOO 11
jacks on
the TV. Match the jack colors (Y = green, P
B = blue, and
P
R = red).
Connect the audio output of the digital set-top box to the
CCOOMMPPOONNEENNTT IINN AAUUDD IIOO 11
jacks on the TV.
2
1
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box. operation
)
Select the
CCoommpp oonneenntt11
input source on the TV using the
IINNPPUUTT
button on the remote control.
If connected to
CCOOMMPPOONNEENNTT IINN 22
input, select the
CCoommpp oonneenntt22
input source on the TV.
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
Image shown may differ from your TV.
ANT
CA
O IN
REMOTE
CONTROL IN
AUDIO
VIDEO
/MONO
AV IN 1
COMPONENT IN
1
2
VIDEO
AUDIO
L
R
Y L RPB PR
1
2
Y, CB/PB, CR/PR
Supported Resolutions
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
15.73 59.94
15.73 60.00
31.47 59.94
31.47 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
27.00 24.00
33.75 30.00
67. 432 59.939
67.50 60.00
26.97 23.94
33.71 29.97
Resolution
720x480i
720x480p
1280x720p
1920x1080i
1920x1080p
Signal
480i
480p
720p
10 8 0 i
10 8 0 p
Component
Yes Yes Yes Yes Yes
HDMI
No Yes Yes Yes Yes
EXTERNAL EQUIPMENT SETUP
23
HDMI Connection
Connect the digital set-top box to
HHDDMMII//DDVVII IINN 11
,
22
or
33
No separate audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box.
)
Select the
HHDDMMII11, 22
or
33
input source on the TV using the
IINNPPUUTT
button on the remote control.
2
1
HDMI-DTV
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
31.47 59.94
31.47 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
27.00 24.00
33.75 30.00
67. 432 59.939
67.50 60.00
26.97 23.94
33.71 29.97
Resolution
720x480p
1280x720p
1920x1080i
1920x1080p
HDMI/DVI IN
2
1
HDMI-DTV OUTPUT
RGB IN(PC)
RS-232C IN
(CONTROL & SERVICE)
OPTICAL DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
1
GG
Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version
1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
GG
HDMI mode supports PCM, AC-3(Dolby Digital) audio format.
NOTE
!
EXTERNAL EQUIPMENT SETUP
24
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
RGB IN (PC)
RS-232C IN
(CONTROL & SERVICE)
OPTICAL DIGITAL AUDIO OUT
AUDIO IN
(RGB/DVI)
HDMI/DVI IN
2
1
LR
DVI-DTV OUTPUT
R
CO
1
2
1
2
GG
A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary.
NOTE
!
Connect the DVI output of the digital set-top box to the
HHDDMMII//DDVVII IINN 11, 22 or33
jack on the TV.
Connect the audio output of the digital set-top box to the
AAUU DDIIOO IINN ((RRGG BB//DDVVII))
jack on the TV.
1. How to connect
2. How to use
Turn on the digital set-top box. (Refer to the owner’s man­ual for the digital set-top box.
)
Select the
HHDDMMII11, 22
or
33
input source on the TV using
the
IINNPPUUTT
button on the remote control.
2
1
EXTERNAL EQUIPMENT SETUP
25

DVD SETUP

Component Connection
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
YPBP
R
Video output ports
on DVD player
Y
Y
Y
Y
PB
B-Y
Cb
Pb
PR
R-Y
Cr
Pr
Connect the video outputs (Y, PB
, PR
)
of the DVD to the
CCOOMMPPOONNEENNTT IINN VVIIDD EEOO 11
jacks on the TV.
Match the jack colors (Y = green, P
B = blue, and PR = red
)
.
Connect the audio outputs of the DVD to the CCOOMMPPOONNEENNTT IINN AAUUDD IIOO 11
jacks on the TV.
1. How to connect
2. How to use
Turn on the DVD player, insert a DVD.
Select the
CCoomm pp oo nneenntt11
input source on the TV using
the
IINNPPUUTT
button on the remote control.
If connected to
CCOOMMPPOONNEENNTT IINN 22
input, select the
CCoommpp oonneenntt22
input source on the TV.
Refer to the DVD player's manual for operating instructions.
2
1
A
REMOTE
CONTROL IN
AUDIO
VIDEO
/MONO
AV IN 1
COMPONENT IN
1
2
VIDEO
AUDIO
L
R
Y L RPB PR
1 2
EXTERNAL EQUIPMENT SETUP
26
EXTERNAL EQUIPMENT SETUP
HDMI Connection
Connect the HDMI output of the DVD to the HHDDMMII//DDVVII IINN 11, 22
or
33
jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Select the
HHDDMMII11, 22
or
33
input source on the TV using
the
IINNPPUUTT
button on the remote control.
Refer to the DVD player's manual for operating instructions.
2
1
HDMI/DVI IN
2
1
RGB IN (PC)
RS-232C IN
(CONTROL & SERVICE)
OPTICAL DIGITAL AUDIO OUT
AUD
(RGB/D
HDMI-DVD OUTPUT
1
EXTERNAL EQUIPMENT SETUP
27

VCR SETUP

Antenna Connection
CABLE
IN
L R
S-VIDEO VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
Wall Jack
Antenna
1
2
Connect the RF antenna out socket of the VCR to the
AANNTTEENNNNAA//CCAABBLLEE IINN
socket
on the TV.
Connect the antenna cable to the RF antenna in socket of the VCR.
1. How to connect
2. How to use
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.
)
2
1
Composite (RCA) Connection
Connect the
AAUUDDII OO/VVIIDDEEOO
jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
1. How to connect
2. How to use
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.
)
Select the
AAVV11
input source on the TV using the
IINNPPUUTT
button on the remote control.
If connected to
AAVV IINN 22
, select
AAVV22
input source on the
TV.
1
GG
If you have a mono VCR, connect the audio cable from the VCR to the
AAUU DDIIOO LL//MMOONNOO
jack of the
TV.
NOTE
!
(PC)
REMOTE
CONTROL IN
1
2
AV IN 1
L
R
AUDIO
VIDEO
/MONO
L R
S-VIDEO VIDEO
OUTPUT SWITCH
ANT IN
ANT OUT
1
EXTERNAL EQUIPMENT SETUP
28

OTHER A/V SOURCE SETUP

EXTERNAL EQUIPMENT SETUP
L R
VIDEO
AV IN 2
L/ MONO
R
AUDIO
VIDEO
USB IN
HDMI IN 3
Camcorder
Video Game Set
Connect the
AAUUDDIIOO/VVIIDDEEOO
jacks between TV and external equipment. Match the jack colors
.
(
Video = yellow, Audio Left = white, and
Audio Right = red
)
1. How to connect
2. How to use
Select the
AAVV22
input source on the TV using
the
IINNPPUUTT
button on the remote control.
If connected to
AAVV II NN 11
input, select the
AAVV11
input source on the TV.
Operate the corresponding external equipment.
1
1
AV IN 2
L/ MONO
R
AUDIO
VIDEO
USB IN
HDMI IN 3
1
i.e)
Connect the USB device to the
UUSSBB II NN
jack on the side
of TV.
1. How to connect
1
2. How to use
After connecting the
UUSSBB IINN
jack, you use the USB function. (
GG
pp..5544
)

USB CONNECTION

- For 42/50PJ350, 50PK350, 42/50PJ550, 50/60PK550,
60PK290, 42/50PJ350C, 50/60PK550C models
EXTERNAL EQUIPMENT SETUP
29

AUDIO OUT CONNECTION

RGB(PC)
RS-232C IN
(CONTROL & SERVICE)
AUDIO
(RGB/DVI)
HDMII/DVI IN
2
1
OPTICAL DIGITAL AUDIO OUT
1
2
GG
When connecting with external audio equipment, such as amplifiers or speakers, you can turn the TV speakers off in the menu. (
GG
pp..8822
)
NOTE
!
G
Do not look into the optical output port. Looking at the laser beam may damage your vision.
GG
Audio with ACP (Audio Copy Protection) function may block digital audio output.
CAUTION
Connect one end of the optical cable to the TV’s
OOPPTTIICCAALL
port of
DDIIGGIITTAALL AAUUDDIIOO OOUUTT
.
Connect the other end of the optical cable to the digital audio input on the audio equipment.
Set the “TV Speaker option - Off” in the AUDIO menu. (
GG
pp..
8822
). See the external audio equipment instruction manual for operation.
1. How to connect
2
3
1
Send the TV’s audio to external audio equipment via the Audio Output port.
EXTERNAL EQUIPMENT SETUP
30

PC SETUP

EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
VGA (D-Sub 15 pin) Connection
(CONTROL & SERVICE)
OPTICAL DIGITAL AUDIO OUT
REMOTE
CONTROL IN
1
2
VIDEO
COMPONEN
VIDEO
RGB IN (PC)
AUDIO IN
(RGB/DVI)
AUDIO
RS-232C IN
1
RS-232C IN
RGB OUTPUT
RS-232C IN
1
2
RS-232C IN
(CONTROL & SERVICE)
OPTICAL DIGITAL AUDIO OUT
RGB IN (PC)
AUDIO IN
(RGB/DVI)
HDMI/DVI IN
2
1
DVI-PC OUTPUT AUDIO
1
2
2. How to use
Turn on the PC and the TV.
Select the
RRGG BB--PPCC
input source on the TV using the
IINNPPUUTT
button on the remote control.
Connect the VGA output of the PC to the
RRGG BB II NN
((
PP CC
))
jack on the TV.
Connect the PC audio output to the
AAUU DDIIOO IINN
((
RRGG BB//DDVV II
))
jack on the TV.
1. How to connect
2
1
2. How to use
Turn on the PC and the TV.
Select the
HHDDMMII11, 22
or
33
input source on the TV using
the
IINNPPUUTT
button on the remote control.
Connect the DVI output of the PC to the
HHDDMMII//DDVVII
IINN 11, 22
or
33
jack on the TV.
Connect the PC audio output to the
AAUU DDIIOO II NN
((RRGG BB//DD VVII))
jack on the TV.
1. How to connect
2
1
Loading...
+ 330 hidden pages