LG 37LT660H, 37LT380H, 42LT380H, 32LT380H, 47LT380H User Manual
...
OWNER’S MANUAL
LED LCD TV
Please read this manual carefully before operating your set and retain it
for future reference.
LT38**
LT64**
LT66**
LT74**
LT76**
www.lg.com
ENGLISH
ENG
TABLE OF CONTENTS
2
TABLE OF CONTENTS
3 LICENSES
3 OPEN SOURCE SOFTWARE
NOTICE
4 INSTALLATION PROCEDURE
4 ASSEMBLING AND
PREPARING
4 Unpacking
6 Separate purchase
7 Parts and buttons
8 Lifting and moving the TV
9 Setting up the TV
9 - Attaching the stand
11 - Mounting on a table
12 - Mounting on a wall
14 - Tidying cables
14 - How to use Dual Lock™
15 MAKING CONNECTIONS
15 Connection of TV
15 Antenna connection
16 HDMI connection
16 Component connection
17 DVI to HDMI connection
17 RGB-PC connection
17 RS-232C Setup
18 Network Setup
18 - Wired Network Connection
18 Audio connection
18 - Digital optical audio connection
19 Speaker output SETUP
19 Headphone connection
19 USB connection
20 CI module connection
20 Euro Scart connection
21 REMOTE CONTROL
24 MAINTENANCE
24 Cleaning your TV
24 - Screen, frame, cabinet and stand
24 - Power cord
24 TROUBLESHOOTING
25 CAUTION FOR USING EZSIGN
2.0
26 SPECIFICATIONS
31 IR CODES
32 EXTERNAL CONTROL DEVICE
SETUP
32 RS-232C Setup
32 Type of connector;
D-Sub 9-Pin Male
32 RS-232C Configurations
33 Communication Parameters
33 Command reference list
34 Transmission / Receiving Protocol
WARNING
If you ignore the warning message, you may
y
be seriously injured or there is a possibility
of accident or death.
CAUTION
If you ignore the caution message, you may
y
be slightly injured or the product may be
damaged.
NOTE
The note helps you understand and use
y
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
3
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary
of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit
divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.”
.
ENGENGLISH
Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
4
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENGLISH
ENG
NOTE
Image shown may differ from your TV.
y
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
y
The available menus and options may differ from the input source or product model that you are
y
using.
New features may be added to this TV in the future.
y
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should
y
be turned off if it will not be watched for some time, as this will reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of brightness of the picture
y
is reduced, and this will reduce the overall running cost.
INSTALLATION PROCEDURE
Open the package and make sure all the accessories are included.
1
Attach the stand to the TV set.
2
Connect an external device to the TV set.
3
Make sure the network connection is available.
4
You can use the TV network functions only when the network connection is made. (Only LT74**, LT76**)
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and item.
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
y
Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
y
Some models have a thin film attached on to the screen and this must not be removed.
y
NOTE
The items supplied with your product may vary depending on the model.
y
Product specifications or contents of this manual may be changed without prior notice due to upgrade
y
of product functions.
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
y
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory
stick does not fit into your TV’s USB port.
B
A
B
A
*A 10 mm
*B 18 mm
ENERGY
SAVING
1 2 3
4 5 6
7 809
LIST
MENU
BACK
ASSEMBLING AND PREPARING
AV MODE
INPUT
TV
FLASHBK
MARK
FAV
P
A
G
3D
CHVOL
E
MUTE
INFO
Q.MENU
ENTER
EXIT
L/R SELECT
FREEZE
RATIO
Remote control,
Batteries (AAA)
(See p.21, 22, 23) Owner’s manual
5
ENGENGLISH
Power Cord Holder
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
EzSign 2.0 Editor CD
(Only
22/26/32/37/42/47LT640E)
32/37/42/47LT38
32/37/42/47LT74**,
**,
32/37/42/47LT76 **)
(See p.14)
Stand Screws
4 EA, M4 x 12
2 EA, M4 x 16
(Only 22LT64
(See p.9)
22LT38**)
**,
Stand Screws
8 EA, M4 x 14
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38
32/37/42/47LT74
32/37/42/47LT76**)
**
**,
(See p.10)
Power cord
(Depending on model)
Stand body / Stand base
(Only 22LT64
(See p.9)
22LT38**)
**,
Stand body / Stand base
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38**,
32/37/42/47LT74**,
32/37/42/47LT76**)
(See p.10)
Stand Screws
8 EA, M4 x 12
(Only 26LT64
26LT38**)
**,
26LT66
**,
(See p.9)
Desk-mount Screw
1 EA
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38**,
32/37/42/47LT74**,
32/37/42/47LT76**)
(See p.11)
DC Adapter
(Only 22/26LT64**,
26LT66**, 22/
26LT38**)
(See p.15)
Stand body / Stand base
(Only 26LT64**, 26LT66**,
26LT38**)
(See p.9)
Protection cover
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38**,
32/37/42/47LT74**,
32/37/42/47LT76**)
(See p.13)
or
Isolator
(Depending on model)
(See p.6)
Dual Lock™
(Only LT64**, LT66**,
LT74**, LT76**)
(See p.14)
Cable Holder
(Depending on model)
(See p.14)
ASSEMBLING AND PREPARING
6
ENGLISH
ENG
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AN-WF100
Wireless Dongle
Compatibility
AN-WF100
Wireless
Dongle
LT640E
•
NOTE
Antenna Isolator Installation Guide
y
- Use this to install TV in a place where there is a voltage difference between TV Set and GND of
antenna signal.
»If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact
might be heated and excessive heat might cause an accident.
- You can improve the safety when watching TV by efficiently removing power voltage from TV
antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall,
mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
- Before starting, be sure that the TV antenna is connected.
LT640H, LT380H, LT660H,
LT740H, LT760H
1. Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains
connection or through other equipment with a connection to protective earthing - and to a cable
distribution system using coaxial cable, may in some circumstances create a re hazard. Connection
to a cable distribution system has therefore to be provided through a device providing electrical
isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
or
Isolator
2. Connect to Set-Top box.
ASSEMBLING AND PREPARING
SPEAKER
STEREO
7
Parts and buttons
(Only 32/37/42/47LT64**,
32/37/42/47LT66
32/37/42/47LT38
32/37/42/47LT74
32/37/42/47LT76
,
**
,
**
,
**
)
**
Screen
(Only 22/26LT64
26LT66
**
22/26LT38
ENGENGLISH
,
**
,
)
**
Remote control sensor
Power Indicator
(Can be adjusted using
the Power Indicator in the
OPTION -menu.)
Clock LED
Button Description
∨∧
Speakers
Scrolls through the saved programmes.
Adjusts the volume level.
Turns the power on or off.
ASSEMBLING AND PREPARING
8
ENGLISH
ENG
Lifting and moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged
and for safe transportation regardless of its type
and size.
CAUTION
Avoid touching the screen at all times, as this
y
may result in damage to the screen.
It is recommended to move the TV in the
y
box or packing material that the TV originally
came in.
Before moving or lifting the TV, disconnect
y
the power cord and all cables.
When holding the TV, the screen should face
y
away from you to avoid damage.
When transporting a large TV, there should
y
be at least 2 people.
When transporting the TV by hand, hold the
y
TV as shown in the following illustration.
When transporting the TV, do not expose the
y
TV to jolts or excessive vibration.
When transporting the TV, keep the TV
y
upright, never turn the TV on its side or tilt
towards the left or right.
Hold the top and bottom of the TV frame
y
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
ASSEMBLING AND PREPARING
M4X20
9
Setting up the TV
Put your TV on a pedestal stand and mount the TV on a table or wall.
Attaching the stand
(Only 22/26LT64**, 26LT66**, 22/26LT38** )
1
M4 x 12
4 EA
Stand Body
Front
Stand Base
3
(Only 22LT64**, 22LT38** )
ENGENGLISH
M4 x 16
Top View
2 EA
2
(Only 26LT64
, 26LT66**, 26LT38**)
**
M4 x 12
4 EA
ASSEMBLING AND PREPARING
M4X20
10
ENGLISH
ENG
(Only 32/37/42/47LT64
3 2 / 37 /42 / 4 7 LT 3 8
32/37/42/47LT76**)
* * ,
1
Stand Body
Stand Base
32/37/42/47LT66
**,
32/37/42/47LT74** ,
**,
M4 x 14
4 EA
Front
Top View
3
2
M4 x 14
4 EA
CAUTION
When attaching the stand to the TV
y
set, place the screen facing down on a
cushioned table or flat surface to protect the
screen from scratches.
Make sure that the screws are fastened
y
completely. (If they are not fastened securely
enough, the TV may tilt forward after being
installed.)
Do not fasten the screws with too much
force; otherwise they may be worn out and
get loosened.
NOTE
Remove the stand before installing the TV
y
on a wall mount by performing the stand
attachment in reverse.
ASSEMBLING AND PREPARING
11
Mounting on a table
Lift and tilt the TV into its upright position on a
1
table.
- Leave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
Connect the power cord to a wall outlet.
2
CAUTION
Do not place the TV near or on sources
y
of heat, as this may result in fire or other
damage.
Attaching the TV to a table
Image shown may differ from your TV.
The TV must be attached to desk so it cannot be
pulled in a forward/backward direction, potentially
causing injury or damaging the pro duct.
(Only 32/37/42/47LT64**, 32/37/42/47LT66**,
32/37/42/47LT38**, 32/37/42/47LT74**,
32/37/42/47LT76**)
10 cm
10 cm
Securing the TV to a table
Fix the TV to a table to prevent from tilting forward,
damage, and potential injury.
Mount the TV on a table, and then insert and
tighten the supplied screw on the rear of the stand.
(Only 32/37/42/47LT64**, 32/37/42/47LT66**,
32/37/42/47LT38**, 32/37/42/47LT74**,
32/37/42/47LT76**)
WARNING
To prevent TV from falling over, the TV
y
should be securely attached to the floor/
wall per installation instructions. Tipping,
shaking, or rocking the TV may cause injury.
Adjusting the angle of the TV to suit view
Swivel 90 degrees to the left or right and adjust the
angle of the TV to suit your view.
ENGENGLISH
4-Screws
(not provided as parts of the product)
Stand
Table
Screws: M4 x L (*L: Table depth + 8-10 mm)
ex) Table depth: 15mm, Screw: M4 x 20
90
CAUTION
When adjusting the angle of the product,
y
watch out for your fingers.
»Personal injury may occur if hands or
fingers are pinched. If the product is tilted
too much, it may fall, causing damage or
injury.
90
ASSEMBLING AND PREPARING
12
ENGLISH
ENG
Securing the TV to a wall
(This feature is not available for all models.)
Insert and tighten the eye-bolts, or TV brackets
1
and bolts on the back of the TV.
- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
Mount the wall brackets with the bolts to the
2
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
Connect the eye-bolts and wall brackets tightly
3
with a sturdy rope.
Make sure to keep the rope horizontal with the
at surface.
Mounting on a wall
Attach an optional wall mount bracket at the rear of
the TV carefully and install the wall mount bracket
on a solid wall perpendicular to the oor. When you
attach the TV to other building materials, please
contact qualied personnel.
LG recommends that wall mounting be performed
by a qualied professional installer.
10 cm
10 cm
10 cm
10 cm
10 cm
CAUTION
Make sure that children do not climb on or
y
hang on the TV.
NOTE
Use a platform or cabinet that is strong and
y
large enough to support the TV securely.
Brackets, bolts and ropes are not provided.
y
You can obtain additional accessories from
your local dealer.
Loading...