LG SAC33601903, 47LH41, 32CL40, 42LH40, 37LH41 User Manual

...
Please read this manual carefully before operating your set and retain it for future reference.
The model and serial number of the TV is located on the back and one side of the TV.
Record it below should you ever need service.
LCD TV OWNER’S MANUAL
37LH55 42LH55 47LH55 55LH55
55LH400C
32CL40 42CL40 47CL40
P/NO : SAC33601903 (0910-REV04)
www.lgusa.com / www.lg.ca
This product qualifies for ENERGY STAR in the “factory default (Home Use)” setting.
Changing the factory default settings or enabling other fea­tures may increase power consumption that could exceed the limits necessary to quality for ENERGY STAR.
Model:
Serial:
1-800-243-0000 USA, Consumer User 1-888-865-3026 USA, Commercial User 1-888-542-2623 CANADA
LG Customer Information Center
2
WARNING / CAUTION
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera­ture accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
WARNING / CAUTION
To prevent fire or shock hazards, do not expose this product to rain or moisture.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause unde­sired operation (of the device).
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.
SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus com­bination to avoid injury from tip-over.
Unplug this apparatus during lighting storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power­supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
1
2
3
4
5
7
8
6
9
10
IMPORTANT SAFETY INSTRUCTIONS
3
4
SAFETY INSTRUCTIONS
Never touch this apparatus or antenna during a thunder or lighting storm.
When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.
Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something.
CAUTION concerning the Power Cord: It is recommend that appliances be placed
upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.
Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
G
ROUN DING
Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC out­let). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
D
ISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The plug must remain readily operable.
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH.
12
11
14
13
16
17
18
19
Power Supply
Short-circuit
Breaker
15
5
A
NTE N NAS Outd o or ant en na gro un di ng
If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of over­head power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna dis­charge unit, connection to grounding elec­trodes and requirements for the grounding electrode.
A
ntenna grounding according to the National Electrical Code, ANSI/NFPA 70
Cle a ning
When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
M
ovi ng
Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV.
V
enti la tion
Install your TV where there is proper ventila­tion. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places.
Take care not to touch the ventilation open­ings. When watching the TV for a long period, the ventilation openings may become hot.
If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center.
Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it.
Keep the product away from direct sunlight.
F
or LCD TV
If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV.
Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.
Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary dis­tortion effects on the screen.
20
23
25
24
26
27
28
21
22
Antenna Lead in Wire
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductor (NEC Section 810-21)
Ground Clamps
Power Service Grounding Electrode System (NEC Art 250, Part H)
Ground Clamp
Electric Service
Equipment
NEC: National Electrical Code
ON DISPOSAL
(Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.
CONTENTS
WARNING / CAUTION
SAFETY INSTRUCTIONS
FEATURE OF THIS TV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PREPARATION
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Stand Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Kensington Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Securing the TV to the wall to prevent falling when the TV is used on a stand
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 24
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Channel Setup
- Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . .
. 48
- Add / Delete Channel (Manual Tuning) . . . . . . 49
- Channel Editing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Favorite Channel Setup / Favorite Channel List . . 52
rief Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
B
Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
AV Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Simple Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
SIMPLINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
USB
Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Music List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Audio out Connection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
WATCHING TV / CHANNEL CONTROL
Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . .
On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . 45
. . 46
. . . . . . . . . . . . . . . . . . . . . . . . . . 47
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 68
Picture Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Preset Picture Settings (Picture Mode) . . . . . . . . . . . . . 72
Manual Picture Adjustment - User Mode . . . . . . . . . . 73
Picture Improvement Technology . . . . . . . . . . . . . . . . . . . . . 74
Expert Picture Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Energy Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Picture Reset
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Demo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6
SOUND & LANGUAGE CONTROL
APPENDIX
Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 82
Clear Voice II
Preset Sound Setting (Sound Mode)
Sound Setting Adjustment - User Mode
alance
B
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
. . . . . . . . . . . . . . . . 84
. . . . . . . . . . . 85
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Audio Reset
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . 88
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
On-Screen Menus Language Selection
. . . . . . . . . . . . . . 91
Caption Mode
- Analog Broadcasting System Captions
Digital Broadcasting System Captions . . . . . . . . 93
-
. . . . . . . 92
- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
TIME SETTING
Clock Setting
- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Auto On/Off Time Setting
. . . . . . . . . . . . . . . . . . . . . . . . . .
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
. . . . 97
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
IR Codes
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
External Control Through RS-232C . . . . . . . . . . . . . . . . .116
Open Source License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
PARENTAL CONTROL / RATINGS
Set Password & Lock System
Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Movie & TV Rating Downloadable Rating
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
. . . . . . . . . . . . . . . . . . . . . . . . . . . 99
7
FEATURE OF THIS TV
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN / BURN-IN” ON YOUR TV SCREEN
The AV Mode optimizes the picture into Cinema, Sports, and game Mode according to the video and audio content. The viewer has the ability to quickly choose the correct mode for the picture they are viewing.
Displays HDTV programs in full 1920 x 1080p resolu­tion for a more detailed picture.
Advance 120Hz panel provides clearer, smoother images, even during fast action scenes creating a more stable structure for a crisper picture.
TruMotion 240Hz displays 240 scenes per second by combining advanced 120Hz technology with scanning backlight. This technology is verified from Intertek &TüV Rheinland.
Automatically enhances and amplifies the sound of human voice frequency range to help keep dialogue audible when background noise swells.
LG TV include a unique invisible speaker system, tuned by renowned audio expert, Mr. Mark Levinson. Speakers are embedded in strategic spots behind the front cabinet and use minute vibrations to turn the entire front bezel into the speaker system. The result is a clean, polished look, and enhanced audio by increasing the “sweet spot”, giving a wider and richer sound field.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."
is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.
Manufactured under license from Dolby Laboratories. “
Dolby
“and the double-D symbol are trademarks of
Dolby Laboratories.
This TV contains the detailed calibrations necessary for professional certification by the Imaging Science Foundation. The resulting ISF “day” and “night” modes will then be accessible by the user to experience the best their LG HDTV has to offer. CALIBRATE LIKE A PRO: Sophisticated and detailed calibrations can be made through the ISFccc mode. Detailed calibration requires a licensed technician. Please contact your local dealer to inquire about an ISF certified technician.
High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV
for an extended period, it can become permanently imprinted on the screen. This phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period
(2 or more hours for LCD, 1 or more hours for Plasma).
Image burn can also occur on the letterboxed
areas of your TV if you use the 4:3 aspect ratio setting for an extended period.
8
PREPARATION
9
ACCESSORIES
PREPARATION
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.
The accessories included may differ from the images below.
1.5V 1.5V
Owner’s Manual Power Cord
Remote Control,
Batteries
FAV
M
UTE
MARK
RATIO
S L E
E P
POWER
Q. MEN
U
MENU
A
V M
O D
E
R E
TU
R
N
V O
L
C
H
1 2 3
4 5 6
7 8
0
9
FLASHBK
P
A G E
INPUT
E NE
RG Y S
A V ING
IN F
O
LI
S
T
ENTER
CD Manual
Option Extras
* Wipe spots on the exterior only with
the polishing cloth.
* Do not wipe roughly when removing
stain. Excessive pressure may cause scratch or discoloration.
Polishing Cloth
Not included with all models
D-sub 15 pin Cable
When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.
For 32/37/42/47/55LH40, 32/37/42/47/55LH41, 37/42/47/55LH55, 55LH400C
Bolts for stand assembly
(Refer to P.16)
Screw for stand fixing
(Refer to P.22)
Protection Cover
x 4
(Except 55LH40, 55LH41,
55LH55, 55LH400C)
(Except 47/55LH40, 47/55LH41,
47/55LH55, 55LH400C)
For 32/42/47CL40
Bolts for stand assembly
(Refer to P.14)
Screw for stand fixing
(Refer to P.22)
x 4 x 4
(Except 47CL40) (Except 47CL40)
Protection Cover
or
PREPARATION
10
FRONT PANEL INFORMATION
PREPARATION
Image shown may differ from your TV.
INPUT
MENU
ENTER
CH
VOL
CHANNEL (D,E) Buttons
VOLUME (+, -) Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
Power/Standby Indicator
Illuminates red in standby mode. Illuminates blue when the TV is switched on. (Can be adjusted
Pow e r Ind ic at or
in the
OPTION menu.
G
p.8 0
)
Remote Control Sensor, Intelligent Sensor
Adjusts picture according to the surrounding conditions
32/37/42/47/55LH40, 32/37/42/47/55LH41, 37/42/47/55LH55, 55LH400C
AC power control switch
OFF ON
SPEAKER
POWER Button
Power/Standby Indicator
Illuminates red in standby mode. Illuminates blue when the set is switched on.
CH
VOL
MENU
INPUT
ENTER
Intelligent Sensor
Adjusts picture according to the surrounding conditions
32/42/47CL40
Remote Control Sensor
SPEAKER
CHANNEL ( , ) Buttons
VOLUME (+, -) Buttons
ENTER Button
MENU Button
INPUT Button
PREPARATION
11
PREPARATION
12
BACK PANEL INFORMATION
PREPARATION
Image shown may differ from your TV.
VIDEO
AUDIO
L R
RS-232C IN
(
CONTROL&SERVICE)
AUDIO IN
(RGB/DVI)
OPTICAL DIGITAL
AUDIO OUT
ANTENNA/
CABLE IN
RGB IN (PC)
AV IN 1
COMPONENT IN
2
3
1
2
1
MONO
( )
AUDIOVIDEO
/DVI IN
L R
1 2 3
6 57
9
AV IN 2
L/MONO
R
AUDIO
VIDEO
USB IN
IN 4
1
8
2
4
PREPARATION
13
AV (Audio/Video) IN
Analog composite connection. Supports standard definition video only (480i).
HDMI/DVI IN, HDMI IN
Digital Connection. Supports HD video and Digital audio. Doesn’t
support 480i. Accepts DVI video using an adapter or HDMI to
DVI cable (not included).
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable).
AUDIO IN (RGB/DVI)
1/8" (0.32 cm) headphone jack for analog PC audio input.
OPTICAL DIGITAL AUDIO OUT
Digital optical audio output for use with amps and home theater systems.
Note: In standby mode, this port doesn’t work.
ANTENNA/CABLE IN
Connect over-the air signals to this jack. Connect cable signals to this jack.
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices. This port is used for Service or Hotel mode.
COMPONENT IN
Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red
and white for audio.
USB INPUT
Used for viewing photos and listening to MP3s.
Power Cord Socket
For operation with AC power. Caution: Never attempt to operate the TV on DC
power.
1
2
3
4
5
8
9
7
6
PREPARATION
STA ND B OD Y
COVE R BAS E
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
1
INSTALLATION (
Only 32/42CL40)
G
When assembling the desk type stand, make sure the screws are fully tightened (If not tightened fully, the TV can tilt forward after the product installation). Do not over tighten.
NOTE
!
Image shown may differ from your TV.
STAND INSTRUCTION (For 32/42/47CL40)
PREPARATION
2
3
Assemble the parts of the
COVE R BAS E
with screws supplied.
Assemble the TV as shown.
of the TV by using the 4
STAN D BOD Y
Fix the 4 bolts securely using the holes in the
4
back of the TV.
14
PREPARATION
15
DETACHMENT
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
1
Loose the bolts from TV.
2
Detach the stand from TV.
3
After removing the stand, install the included p
rot e ctio n c o ver
over the hole for the stand.
Press the
PROTECTIO N COVER
into the TV
until you hear it click.
PROTECTION COVER
PREPARATION
16
STAND INSTRUCTION
(For 32/37/42/47/55LH40, 32/37/42/47/55LH41, 37/42/47/55LH55, 55LH400C)
PREPARATION
Image shown may differ from your TV.
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the back of the TV.
1
2
3
INSTALLATION (Except 55LH40, 55LH41, 55LH55, 55LH400C)
G
When assembling the desk type stand, make sure the bolt is fully tightened (If not tightened fully, the TV can tilt forward after the product installa­tion). Do not over tighten.
NOTE
!
PREPARATION
17
DETACHMENT
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
1
Loose the bolts from TV.
2
Detach the stand from TV.
3
After removing the stand, install the included p
rot e ctio n c o ver
over the hole for the stand.
Press the
PROTECTIO N COVER
into the TV
until you hear it click.
PROTECTION COVER
PREPARATION
18
VESA WALL MOUNTING
PREPARATION
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer.
G
Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock.
CAUTION
G
Screw length needed depends on the wall mount used. For further information, refer to the instruc­tions included with the mount.
G
Standard dimensions for wall mount kits are shown in the table.
G
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
G
Do not use screws longer then the standard dimen­sion, as they may cause damage to the inside to the TV.
G
For wall mounts that do not comply with the VESA
standard screw specifications, the length of the screws may differ depending on their specifica­tions.
G
Do not use screws that do not comply with the VESA standard screw specifications.
Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents.
G
LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installa­tion instructions.
NOTE
!
Model
VESA (A *B)
Standard Screw Quantity
Wall Mounting Bracket
(sold separately)
32LH40, 32LH41,
32CL40
55LH40, 55LH41,
55LH55, 55LH400C
37LH40, 37LH41, 37LH55, 42LH40,
42LH41, 42LH55,
42CL40, 47LH40,
47LH41, 47LH55,
47CL40
200* 100 M4 4
200* 200 M6 4
400* 400 M6 4
AW-55LH40M
AA
BB
AW-47LG30M
RW230 AW-47LG30M
PREPARATION
19
CABLE MANAGEMENT
Connect the cables as necessary. To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP as shown.
CABLE MANAGEMENT CLIP
1
2
Put the cables inside the C
ABLE MANAGEMENT
CLIP and snap it closed.
3
For 32/42/47CL40
Image shown may differ from your TV.
PREPARATION
Connect the cables as necessary. To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP as shown.
CABLE MANAGEMENT CLIP
1
2
Put the cables inside the C
ABLE MANAGEMENT
CLIP and snap it closed.
3
For 32/37/42/47/55LH40, 32/37/42/47/55LH41, 37/42/47/55LH55, 55LH400C
Image shown may differ from your TV.
CABLE MANAGEMENT
PREPARATION
20
PREPARATION
21
DESKTOP PEDESTAL INSTALLATION
SWIVEL STAND
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
Image shown may differ from your TV.
4 inches
G
Ensure adequate ventilation by following the clearance recommendations.
G
Do not mount near or above any type of heat source.
CAUTION
4 inches
4 inches
4 inches
PREPARATION
22
ATTACHING THE TV TO A DESK
(Except 47/55LH40, 47/55LH41, 47/55LH55, 47CL40, 55LH400C)
PREPARATION
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
G
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
WARNING
1-Screw
(provided as parts of the product)
Desk
Stand
KENSINGTON SECURITY SYSTEM
This feature is not available for all models.
- The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below.
- For the detailed installation and use of the Kensington Security
System, refer to the user’s guide provided with the Kensington Security System.
For further information, contact
h
ttp: //www .k ensi n gton . com
, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as note­book PCs and LCD projectors.
NOTE: The Kensington Security System is an optional accessory.
PREPARATION
23
SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
Use a sturdy rope (sold separately) to tie the produ
ct. It is safer to tie
the rope so it becomes horizontal between the wall and the product.
You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).
Image shown may differ from your TV.
G
Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
G
To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.
NOTE
!
PREPARATION
24
ANTENNA OR CABLE CONNECTION
PREPARATION
To prevent damage do not connect to the power outlet until all connections are made between the devices.
Image shown may differ from your TV.
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.
For optimum picture quality, adjust antenna direction if needed.
2. Cable
Wall Antenna Socket
Outdoor Antenna (VHF, UHF)
Cable TV Wall Jack
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
RF Coaxial Wire (75 ohm)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Be careful not to bend the copper wire when connecting the antenna.
Copper Wire
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
If the antenna is not installed properly, contact your dealer for assistance.
ANTENNA/
CABLE IN
ANTENNA/
CABLE IN
EXTERNAL EQUIPMENT SETUP
25
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUP
This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device.
Component Connection
1. How to connect
Connect the video outputs (Y, PB, PR)of the digital set­top box to the
C
OMPO NENT IN VIDEO 1
jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).
Connect the audio output of the digital set-top box to the
COMP ONENT IN AU DI O 1
jacks on the TV.
2
1
2. How to use
Turn on the digital set-top box. (
R
efer to the owner’s manual for the digital set-top box operation.
)
Select the
C
omp on ent1
input source on the TV using the
IN P UT
button on the remote control.
If connected to
COM P ONEN T IN 2
input, select the
Com po nent 2
input source on the TV.
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
Image shown may differ from your TV.
Y, CB/PB, CR/P
R
Supported Resolutions
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
15.73 59.94
15.73 60.00
31.47 59.94
31.50 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
26.97 23.976
27.00 24.00
33.71 29.97
33.75 30.00
67.432 59.94
67.50 60.00
Resolution
720x480i
7
20x480p
1280x720p
1920x1080i
1920x1080p
Signal
480i
480p
720p
1080i
1080p
Component
Yes
Y
es
Yes
Yes
Yes
HDMI
No
Y
es
Yes
Yes
Yes
AV IN 1
2
3
1
MONO
( )
AUDIOVIDEO L R
/DVI IN
VIDEO
AUDIO
L R
COMPONENT IN
2
1
Y L RPB PR
1
2
EXTERNAL EQUIPMENT SETUP
26
EXTERNAL EQUIPMENT SETUP
HDMI Connection
Connect the digital set-top box to
HDMI /D VI IN 1
,
2, 3
, or
4
jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Turn on the digital set-top box. (
R
efer to the owner’s manual for the digital set-top box.
)
Select the
HDMI1, HDMI2, HDMI3
, or
HDMI4
input
source on the TV using the
INPUT
button on the remote
control.
2
1
HDMI-DTV
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
31.47 59.94
31.50 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
26.97 23.976
27.00 24.00
33.71 29.97
33.75 30.00
67.432
59.94
67.50 60.00
Resolution
720x480p
1280x720p
1920x1080i
1920x1080p
AUDIO
L R
AUDIO IN
(RGB/DVI)
O
A
C
RGB IN (PC)
AV IN 1
1
MONO
( )
AUDIOVIDEO L R
2
3
1
/DVI IN
HDMI OUTPUT
RS-232C IN
(
CONTROL&SERVICE)
1
G
Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.
NOTE
!
EXTERNAL EQUIPMENT SETUP
27
DVI to HDMI Connection
AUDIO
L R
OPTICAL DIG
AUDIO OU
ANTENNA
CABLE IN
RGB IN (PC)
AV IN 1
1
MONO
( )
AUDIOL R
2
3
1
/DVI IN
AUDIO IN
(RGB/DVI)
L R
DVI OUTPUT
AUDIO
RS-232C IN
(
CONTROL&SERVICE)
1
2
G
A DVI to HDMI cable or adapter is required for this con­nection. DVI doesn't support audio, so a separate audio connection is necessary.
NOTE
!
Connect the DVI output of the digital set-top box to the
H
DMI / DVI IN 1, 2
, or 3jack on the TV.
Connect the digital set-top box audio output to the AUD IO I N
(
RGB /DVI
)
jack on the TV.
1. How to connect
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box.
)
Select the
HDMI1, HDMI2
, or
HDMI3
input source on the
TV using the
INPUT
button on the remote control.
2
1
EXTERNAL EQUIPMENT SETUP
AV IN 1
2
3
1
MONO
( )
AUDIOVIDEO L R
/DVI
VIDEO
AUDIO
L R
COMPONENT IN
2
1
Y L RPB PR
1 2
DVD SETUP
Component Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
Connect the video outputs (Y, PB, PR)of the DVD to the
1
2
OMPO NENT IN VID EO 1
C
Match the jack colors (Y = green, P
jacks on the TV.
B = blue, and PR = red
Connect the audio outputs of the DVD to the
OMPO NENT IN AUD IO 1
C
jacks on the TV.
)
.
2. How to use
Turn on the DVD player, insert a DVD.
Select the the
If connected to
omp on ent2
C
Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
IN P UT
Com po nent1
input source on the TV using
button on the remote control.
COM P ONEN T IN 2
input source on the TV.
input, select the
28
Component ports on the TV
Video output ports
on DVD player
Y PB PR
B
Y
Y
Y
Y
P
B-Y
C
Pb
b
PR
R-Y
Cr
Pr
EXTERNAL EQUIPMENT SETUP
29
Composite (RCA) Connection
VIDEO
AUDIO
L R
COMPONENT IN
2
3
1
2
1
/DVI IN
AV IN 1
MONO
( )
AUDIOVIDEO L R
L R
VIDEO
AUDIO
HDMI Connection
AUDIO
L R
AUDIO IN
(RGB/DVI)
OP
A
AN
C
RGB IN (PC)
AV IN 1
1
MONO
( )
AUDIOVIDEO L R
2
3
1
/DVI IN
HDMI OUTPUT
RS-232C IN
(
CONTROL&SERVICE)
1
Connect the
A
UD I O
/
V
ID E O
jacks between TV and DVD. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
1. How to connect
2. How to use
Turn on the DVD player, insert a DVD.
Select the
AV 1
or
AV 2
input source on the TV using the
IN P UT
button on the remote control.
Refer to the DVD player's manual for operating instructions.
1
Connect the HDMI output of the DVD to the H
DMI / DVI IN 1, 2, 3
or 4jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Select the
HDMI1, HDMI2, HDMI3
, or
HDMI4
input
source on the TV using the
IN P UT
button on the remote
control.
Refer to the DVD player's manual for operating instructions.
2
1
G
Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.
NOTE
!
1
EXTERNAL EQUIPMENT SETUP
30
VCR SETUP
EXTERNAL EQUIPMENT SETUP
Antenna Connection
Connect the RF antenna out socket of the VCR to the
ANT E NNA/ CA BLE I N
sock-
et on the TV.
Connect the antenna cable to the RF antenna in socket of the VCR.
1. How to connect
2. How to use
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
Insert a video tape into the VCR and press P
LAY on the VCR. (Refer to the VCR owner’s
manual.
)
2
1
OPTICAL DIGITAL
AUDIO OUT
RGB IN (PC)
ANTENNA/
CABLE IN
L R
S-VIDEO VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
AUDIO
RS-232C IN
(
CONTROL&SERVICE)
Wall Jack
Antenna
1
2
Loading...
+ 106 hidden pages