Order Number : GETEC-C1-09-264 FCC Class B CertificationTest Report Number : GETEC-E3-09-158 Page 1 / 1
APPENDIX G
: USER’S MANUAL
EUT Type: LED LCD TV/Monitor
FCC ID.: BEJ42LE7500UC
OWNER’S MANUAL
LED LCD TV / LCD TV
PLASMA TV
Please read this manual carefully before operating
your set and retain it for future reference.
P/NO : SAC34134203 (1001-REV00)
www.lge.com
WARNING / CAUTION
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equi-
lateral triangle is intended to alert
the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the
point of the cable entry as practical.
FCC Notice
Class B digital device
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC
Rules.
Operation is subject to the following two conditions: (1) This device may not cause (harmful)
interference, and (2) this device must accept
any interference received, including interference
that may cause undesired operation (of the
device).
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any
way without written authorization from LG
Electronics. Unauthorized modification could
void the user’s authority to operate this product.
2
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
1
Clean only with dry cloth.
2
Do not block any ventilation openings. Install in
3
accordance with the ma nufacturer’s instructions.
Protect the power cord from being walked
6
on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
Only use attachments/accessories speci-
7
fied by the manufacturer.
Use only with the cart, stand, tripod, bracket,
8
or table specified by the manufacturer, or
sold with the apparatus. When a cart is
used, use caution when moving the cart/
apparatus combination to avoid injury from
tip-over.
Do not install near any heat sources such as
4
radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized
5
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong, The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Unplug this apparatus during lighting
9
storms or when unused for long periods
of time.
Refer all servicing to qualified service per-
10
sonnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been
dropped.
3
SAFETY INSTRUCTIONS
Never touch this apparatus or antenna during
11
a thunder or lighting storm.
When mounting a TV on the wall, make sure
12
not to install the TV by the hanging power
and signal cables on the back of the TV.
Do not allow an impact shock or any objects
13
to fall into the product, and do not drop onto
the screen with something.
CAUTION concerning the Power Cord:
14
It is recommend that appliances be placed
upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance and has no additional outlets or
branch circuits. Check the specification page
of this owner's manual to be certain.
Do not connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged
or cracked wire insulation are dangerous . Any
of these conditions could result in electric
shock or fire. Periodically examine the cord of
your appliance, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by
an authorized servicer. Protect the power cord
from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where the
cord exits the appliance.
Do not use a damaged or loose power cord.
Do not pull on the power cord to unplug the
TV. Grasp the plug when unplugging the
power cord.
WARNING - To reduce the risk of fire or elec-
15
trical shock, do not expose this product to
rain, moisture or other liquids. Do not touch
the TV with wet hands. Do not install this
product near flammable objects such as
gasoline or candles or expose the TV to
direct air conditioning.
Do not expose to dripping or splashing and
16
do not place objects filled with liquids, such
as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
GROUNDING
17
Ensure that you connect the earth ground
wire to prevent possible electric shock (i.e. a
TV with a three-prong grounded AC plug
must be connected to a three-prong grounded AC outlet). If grounding methods are not
possible, have a qualified electrician install a
separate circuit breaker.
Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas
pipes.
Power
Supply
Short-circuit
Breaker
DISCONNECTING DEVICE FROM MAINS
18
Mains plug is the disconnecting device. The
plug must remain readily operable.
4
As long as this unit is connected to the AC
19
wall outlet, it is not disconnected from AC
power even if you turn off the power switch
on the unit.
ANTENNAS
20
Outdoor antenna grounding
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system should not be located in the vicinity of
overhead power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur.
Be sure the antenna system is grounded so as
to provide some protection against voltage
surges and built-up static charges.
Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of
grounding conductors, location of antenna
discharge unit, connection to grounding electrodes and requirements for the grounding
electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Ventilation
23
Install your TV where there is proper ventilation. Do not install in a confined space such
as a bookcase. Do not cover the product
with cloth or other materials (e.g.) plastic
while plugged in. Do not install in excessively dusty places.
Take care not to touch the ventilation open-
24
ings. When watching the TV for a long
period, the ventilation openings may
become hot.
If you smell smoke or other odors coming
25
from the TV or hear strange sounds, unplug
the power cord contact an authorized service
center.
Do not press strongly upon the panel with
26
hand or sharp object such as nail, pencil or
pen, or make a scratch on it.
Ground Clamp
Electric Service
Equipment
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
NEC: National Electrical Code
Cleaning
21
When cleaning, unplug the power cord and
rub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners or benzene.
Moving
22
Make sure the product is turned off, unplugged
and all cables have been removed. It may take
2 or more people to carry larger TVs. Do not
press against or put stress on the front panel
of the TV.
27
Keep the product away from direct sunlight.
For LED LCD TV/LCD TV
28
If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.
Some minute dot defects may be visible on
the screen, appearing as tiny red, green, or
blue spots. However, they have no adverse
effect on the monitor's performance.
Avoid touching the LCD screen or holding
your finger(s) against it for long periods of
time. Doing so may produce some temporary distortion effects on the screen.
5
CONTENTS
SAFETY INSTRUCTIONS
Important Safety Instructions............................3
Optional Extras
Front Panel Information
Back Panel Information
Stand instructions
VESA Wall Mounting
Cable Management
Desktop Pedestal Installation
Swivel Stand
Attaching the TV to a Desk
Kensington Security System
Securing the TV to the wall to prevent falling
when the tv is used on a stand
Antenna or Cable Connection
- Channel Editing
Favorite Channel Setup
Favorite Channel List
Channel List
Channel Information
Channel Brief Information
Input List
Input Label
Reset to Factory Default (Initial Setting)
Mode Setting
Demo Mode
AV Mode
Game
Some of these features are not available on all models.
High-definition television. Highresolution digital television broadcast and playback system composed of roughly a million or more
pixels, 16:9 aspect-ratio screens,
and AC3 digital audio. A subset of
digital television, HDTV formats
include 1080p, 1080i, and 720p
resolutions.
Manufactured under license from
Dolby Laboratories. “Dolby “and the
double-D symbol are trademarks of
Dolby Laboratories.
HDMI, the HDMI logo and HighDefinition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC."
ABOUT DIVX VIDEO: DivX® is a
digital video format created by
DivX,Inc. This is an official DivX
Certified device that plays DivX
video. Visit www.divx.com for more
information and software tools to
convert your files into DivX video.
ABOUT DIVX VIDEO-ONDEMAND: This DivX Certified®
device must be registered in order
to play DivX Video-on-Demand
(VOD) content. To generate the
registration code, locate the DivX
VOD section in the device setup
menu. Go to vod.divx.com with this
code to complete the registration
process and learn more about
DivX VOD.
“DivX Certified to play DivX video
up to HD 1080p, including premium content”
“Pat. 7,295,673;
7,460,688;7,519,274”
Displays HDTV programs in full
1920 x 1080p resolution for a more
detailed picture.
This TV contains the detailed calibrations necessary for professional
certification by the Imaging Science
Foundation. The resulting ISF “day”
and “night” modes will then be
accessible by the user to experience the best their LG HDTV has to
offer.
Sophisticated and detailed calibrations can be made through the
ISFccc mode.
Detailed calibration requires a
licensed technician.
Please contact your local dealer to
inquire about an ISF certified technician.
THX (Thomlinson Holman’s
Experiment) is an audio and video
certification standard established
by George Lucas and Thomlinson.
A THX certified display guarantees
screen quality that exceeds the display standard specification in both
hardware and software.
A unique invisible speaker system
tuned by renowned audio expert,
Mr. Mark Levinson. Speakers are
embedded in strategic spots
behind the front cabinet and use
minute vibrations to turn the entire
front bezel into the speaker system.
The result s a clean, polished look,
and enhanced audio by increasing
the “sweet spot”, giving a wider and
richer sound field.
Unlike other sensors which can only
sense brightness of ambient light,
LG’s “Intelligent Sensor” uses
4,096 sensing steps to evaluate its
surroundings. Using a sophisticated algorithm, the LG processes
picture quality elements including
brightness, contrast, color, sharpness and white balance. The result
is a picture optimized for it’s surroundings, more pleasing to watch
and which can also save up to 50%
in power consumption.
8
AV Mode is three preset picture
and audio settings. It allows the
viewer to quickly switch between
common settings. It includes
Cinema, Sports, and Game Modes.
Automatically enhances and amplifies the sound of human voice frequency range to help keep dialogue audible when background
noise swells.
Stream movies, TV shows and
video, and get up to the minute
news, stock information and weather updates directly to your TV using
Yahoo!, Netflix, YouTube and Vudu.
View videos and photos and listen
to music on your TV through USB
2.0 (‘videos’ dependent on model).
IMPORTANT INFORMATION TO PREVENT “IMAGE
BURN / BURN-IN” ON YOUR TV SCREEN
ᯫ
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed
on the TV for an extended period, it can become permanently imprinted on the screen. This
phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
ᯫ
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged
period (2 or more hours for LCD, 1 or more
hours for Plasma).
ᯫ
Image burn can also occur on the letterboxed areas of your TV if you use the 4:3
aspect ratio setting for an extended period.
ON DISPOSAL
(Only Hg lamp used LED LCD TV/LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this
product with general household waste. Disposal of this product must be carried out in accordance to
the regulations of your local authority.
9
PREPARATION
PREPARATION
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.
PREPARATION
The accessories included may differ from the images below.
1.5V 1.5V
Owner’s ManualCD Manual,
Program CD
Not included with all models
* Wipe spots on the exterior only
with the polishing cloth.
* Do not wipe roughly when remov-
Polishing Cloth
Not included with all models
ing stains. Excessive pressure may
cause scratches or discoloration.
Ferrite core can be used to reduce the electromagnetic waves that may interfere with the TV. Install the
Ferrite core on the power cable close to the wall plug.
Ferrite Core
50/60PK750
(For 50PK750)
Remote Control,
Batteries (AAA)
Option Extras
D-sub 15 pin Cable
When using the VGA (D-sub 15
pin cable) PC connection, the
user must use shielded signal
interface cables with ferrite cores
to maintain standards compliance.
* Wipe spots on the exterior only with the polishing cloth.
* Do not wipe roughly when removing stains. Excessive pressure may
* For cleaning front frame, please slowly wipe in one direction after
Cable Holder
(Refer to p.30)
cause scratches or discoloration.
spraying water 1-2 times on cleansing cloths. Please remove excessive moisture after cleaning. Excessive moisture may cause water
stains on the frame.
Remote Control,
Batteries (AAA)
PREPARATION
Power Cord
x 2
Component gender cable,
AV gender cable
OPTIONAL EXTRAS
Optional extras can be changed or modified for quality improvement without any notification.
Contact your dealer for buying these items.
This device only works with compatible LG LED LCD TV, LCD TV, or Plasma TV.
Wireless Media Box
(AN-WL100W)
Wireless LAN for Broadband/
DLNA Adaptor
(AN-WF100)
11
42/47/55LE5400, 42/47/55LE5500, 42/47/55LE7500
Power/Standby Indicator
Illuminates red in standby mode.
SPEAKER
Illuminates white when the TV is switched on.
(Can be adjusted using the Power Indicator in
the OPTION menu.
PREPARATION
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to
the surrounding conditions
Źp.148)
Touch Button
Light the button by touching first. At this time, you can use the desired button.
VOLENTERCHMENUINPUT
CHANNEL
(
ᰝ,ᰜ)
Buttons
VOLUME
(-, +)
Buttons
ENTER
Button
MENU
Button
INPUT
Button
POWER
Button
15
PREPARATION
ᯫ
Image shown may differ from your TV.
PREPARATION
47/55LE8500
SPEAKER
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to
the surrounding conditions
Power/Standby Indicator
Illuminates red in standby mode.
Turn off red smoothly when the TV is
switchced on. (Can be adjusted using
the Power Indicator in the OPTION
menu.
Źp.148)
Touch Button
You can use the desired button function by touching.
HDMI cables and USB
devices should have bezels
less than 0.39 inches (10
mm) thick.
USB IN 1USB IN 2
R
P
B
COMPONENT IN3
AUDIO / Y P
H/P
IN 4
AV IN2
6
VIDEO / AUDIO
18
*A0.39 inches (10 mm)
PREPARATION
1
LAN
Network connection for Netflix, Yahoo! TV
Widgets, etc.
Also used for video, photo and music files on
a local network.
2
HDMI/DVI IN, HDMI IN
Digital Connection.
Supports HD video and Digital audio. Doesn’t
support 480i.
Accepts DVI video using an adapter or HDMI
to DVI cable (not included).
3
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin
cable (VGA cable).
AUDIO IN (RGB/DVI)
1/8” (0.32 cm) headphone jack for analog PC
audio input.
4
RS-232C IN (SERVICE ONLY), SERVICE
ONLY
This port is used for service.
7
ANTENNA/CABLE IN
Connect over-the-air or cable signals to this
jack.
8
COMPONENT IN
Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video &
red and white for audio.
9
WIRELESS CONTROL
Connect the Wireless Ready Dongle to the TV
to control the external input devices connected to Media Box wirelessly.
10
USB INPUT
Used for viewing videos, photos and listening
to MP3s.
11
HEADPHONE INPUT
Plug the headphone into the headphone
socket.
5
OPTICAL DIGITAL AUDIO OUT
Digital optical audio output for use with amps
and home theater systems.
Note: In standby mode, this port doesn’t work.
6
AV (Audio/Video) IN
Analog composite connection. Supports
standard definition video only (480i).
12
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on
DC power.
13
REMOTE CONTROL IN
For a wired remote control.
19
PREPARATION
VESA WALL MOUNTING
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer.
PREPARATION
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.
Model
32LD550200
42/46LD550,
47LD650,
42/47LE5400,
42/47LE5500,
42/47LE7500,
47LE8500
52LD550, 55LD650,
55LE5400,
55LE5500,
55LE7500,
55LE8500
VESA (A * B)
A
B
100M44
*
200
400
200M64
*
400M64
*
Standard
Screw
Quantity
Wall Mounting Bracket
(sold separately)
RW230 AW-47LG30M
AW-47LG30M
AW-55LH40M
AW-55LH40M
26
60LD550600
50PK750400
60PK750600
400M64
*
400M64
*
400M84
*
AW-50PG60M AW-50PG60MS
AW-60PG60M AW-60PG60MS
!
NOTE
PREPARATION
Ź Screw length needed depends on the wall
mount used. For further information, refer to
the instructions included with the mount.
Ź
Standard dimensions for wall mount kits are
shown in the table.
Ź
When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.
Ź
Do not use screws longer then the standard
dimension, as they may cause damage to the
inside to the TV.
Ź
For wall mounts that do not comply with the
VESA standard screw specifications, the length
of the screws may differ depending on their
specifications.
Ź Do not use screws that do not comply with the
VESA standard screw specifications.
Do not use fasten the screws too strongly, this
may damage the TV or cause the TV to a fall,
leading to personal injury. LG is not liable for
these kinds of accidents.
Ź
LG is not liable for TV damage or personal
injury when a non-VESA or non specified wall
mount is used or the consumer fails to follow
the TV installation instructions.
CAUTION
Ź Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to
electric shock.
27
DESKTOP PEDESTAL INSTALLATION
ᯫ
Image shown may differ from your TV.
For proper ventilation, allow a clearance of 10.1 cm (4 inch) on all four sides from the wall.
10.1 cm (4 inch)
10.1 cm (4 inch)
10.1 cm (4 inch)
10.1 cm (4 inch)
CAUTION
Ź Ensure adequate ventilation by following the clearance recommendations.
Ź Do not mount near or above any type of heat source.
PREPARATION
SWIVEL STAND
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees
to suit your viewing position.
31
SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND
ᯫ
You should purchase necessary components to prevent the TV from tipping over (when not using a
wall mount).
ᯫ
Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward
direction, potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
ᯫ
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the
picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the
bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket
that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
PREPARATION
ᯫ
Use a sturdy rope (sold separately) to tie the product. It is safer to tie the
rope so it becomes horizontal between the wall and the product.
!
NOTE
Ź Use a platform or cabinet strong enough and large enough to support the size and weight of
the TV.
Ź
To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are
the same.
33
PREPARATION
ᯫ
To prevent damage do not connect to the power outlet until all connections are made between the
devices.
ᯫ
Image shown may differ from your TV.
PREPARATION
ANTENNA OR CABLE CONNECTION
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.
For optimum picture quality, adjust antenna direction if needed.
Wall
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
RF Coaxial Wire (75 Ω)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Copper Wire
Be careful not to bend the copper wire
when connecting the antenna.
ANTENNA/
CABLE IN
2. Cable
ANTENNA/
CABLE IN
Cable TV
Wall Jack
RF Coaxial Wire (75 Ω)
ᯫ
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
ᯫ
For much more information about antennas visit our Knowledgebase at LGknowledgebase.com.
Search for antenna.
34
EXTERNAL EQUIPMENT SETUP
ᯫ
To prevent the equipment damage, never plug in any power cords until you have finished connecting all
equipment.
ᯫ
I
mage shown may differ from your TV.
HD RECEIVER SETUP
This TV can receive digital over-the-air/digital cable signals without an external digital set-top box.
However, if you do receive digital signals from a digital set-top box or other digital external device.
Component Connection
1. How to connect
Connect the video outputs (Y, P B, PR
1
digital set-top box to the COMPONENT IN
VIDEO 1, 2,or3* jacks on the TV. Match the
jack colors (Y = green, P
Connect the audio output of the digital set-top
2
box to the COMPONENT IN AUDIO 1, 2,or3*
jacks on the TV.
2. How to use
ᯫ
Turn on the digital set-top box.
(
Refer to the owner’s manual for the digital set-top
box operation.
ᯫ
Select the Component1, Component2, or
Component3 input source on the TV using the
INPUT button on the remote control.
* Component3: For LED LCD TV
)
)
of the
B = blue, and PR = red).
/DVI IN
3
2
1
(RGB/DVI)
AUDIO IN
YLRPBP
RGB IN (PC)
OPTICAL
DIGITAL
AUDIO OUT
2
YPBP
1
R
12
RS-232CIN
(
SERVICE ONLY)
L(MONO)
VIDEO
R
VIDEO
AUDIO
L R
AUDIO
AV IN 1
R
COMPONENT IN
EXTERNAL EQUIPMENT SETUP
Supported ResolutionsY, CB/PB, CR/PR
SignalComponentHDMI
480iYesNo
Resolution
720x480i
480pYesYes
720pYesYes
720x480p
1080iYesYes
1080pYesYes
1280x720p
1920x1080i
1920x1080p
Horizontal
Frequency(KHz
)
Frequency(KHz
15.7359.94
15.7360.00
31.4759.94
31.5060.00
44.9659.94
45.0060.00
33.7259.94
33.7560.00
26.9723.976
27.0024.00
33.7129.97
33.7530.00
67.43259.94
67.5060.00
Vertical
)
35
EXTERNAL EQUIPMENT SETUP
For LED LCD TV
EXTERNAL EQUIPMENT SETUP
USB IN 1USB IN 2
R
P
B
COMPONENT IN3
AUDIO / Y P
H/P
IN 4
AV IN2
VIDEO / AUDIO
1
2
YLRP
B
P
R
36
HDMI Connection
2
1. How to connect
Connect the digital set-top box to HDMI/DVI IN
1
1, 2, 3, or 4 jack on the TV.
No separate audio connection is necessary.
2
HDMI supports both audio and video.
2. How to use
ᯫ
Turn on the digital set-top box.
(
Refer to the owner’s manual for the digital set-
top box.
ᯫ
Select the HDMI1, HDMI2, HDMI3, or HDMI4 input
source on the TV using the
remote control.
!
NOTE
Ź If an HDMI cable doesn’t support HDMI version 1.3, it
can cause flickers or no screen display. In this case
use the latest cables that support HDMI version 1.3.
Ź
HDMI Audio Supported Format: AC3 (32KHz,
44.1KHz,48KHz), Linear PCM (32KHz, 44.1KHz,48KHz)
)
INPUT
button on the
LAN
ꔡ
WIRELESS
CONTROL
/DVI IN
1
HDMI OUTPUT
3
2
1
(RGB/DVI)
AUDIO IN
RGB IN (PC)
OPTICAL DIGITAL
AUDIO OUT
2
YPBP
1
VIDEO
VIDEO
R
RS-23
(
SERVICE
L(MONO
EXTERNAL EQUIPMENT SETUP
L
A
HDMI-DTV
Resolution
720x480p
1280x720p
1920x1080i
1920x1080p
Horizontal
Frequency(KHz
)
Frequency(KHz
31.47 59.94
31.5060.00
44.9659.94
45.0060.00
33.7259.94
33.7560.00
26.9723.976
27.0024.00
33.7129.97
33.7530.00
67.43259.94
67.5060.00
Vertical
)
37
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
1. How to connect
Connect the DVI output of the digital set-top
EXTERNAL EQUIPMENT SETUP
1
box to the HDMI/DVI IN 1, 2, 3, or 4* jack on
the TV.
Connect the digital set-top box audio output to
2
the AUDIO IN (RGB/DVI) jack on the TV.
2. How to use
ᯫ
Turn on the digital set-top box.
(
Refer to the owner’s manual for the digital set-
top box.
ᯫ
Select the HDMI1, HDMI2, HDMI3, or HDMI4* input
source on the TV using the
remote control.
)
INPUT
button on the
LAN
ꔡ
WIRELESS
CONTROL
RS-232C IN
(
VIDEO
VIDEO
R
SERVICE ONLY)
L(MONO)
L R
AUDIO
AUDIO
R
RGB IN (PC)
/DVI IN
3
(RGB/DVI)
OPTICAL DIGITAL
2
AUDIO IN
AUDIO OUT
1
2
YPBP
1
1
2
* HDMI 4: For Plasma TV
!
NOTE
Ź A DVI to HDMI cable or adapter is required for this con-
nection. DVI doesn't support audio, so a separate audio
connection is necessary.
DVI OUTPUT
LR
AUDIO
38
DVD SETUP
Component Connection
1. How to connect
Connect the video outputs (Y, P B, PR
1
DVD to the COMPONENT IN VIDEO 1, 2,or3*
jacks on the TV.
Match the jack colors (Y = green, P
P
R = red
Connect the audio outputs of the DVD to the
2
COMPONENT IN AUDIO 1, 2,or3* jacks on the
TV.
2. How to use
ᯫ
Turn on the DVD player, insert a DVD.
ᯫ
Select the Component1, Component2, or
Component3 input source on the TV using the
INPUT button on the remote control.
ᯫ
Refer to the DVD player’s manual for operating
instructions.
)
.
)
of the
B = blue, and
/DVI IN
3
2
1
(RGB/DVI)
AUDIO IN
YLRPBP
RGB IN (PC)
OPTICAL DIGITAL
AUDIO OUT
2
YPBP
1
1
VIDEO
R
RS-232C IN
(
SERVICE ONLY)
VIDEO
R
L(MONO)
L R
AUDIO
2
AUDIO
AV IN 1
R
COMPONENT IN
EXTERNAL EQUIPMENT SETUP
* Component3: For LED LCD TV
Component Input ports
To get better picture quality, connect a DVD player
to the component input ports as shown below.
Component ports on
the TV
Video output ports
on DVD player
YPBP
YPBP
YB-YR-Y
YCbCr
YPbPr
R
R
For LED LCD TV
USB IN 1USB IN 2
R
P
B
COMPONENT IN3
AUDIO / Y P
H/P
IN 4
AV IN2
VIDEO / AUDIO
1
2
YLRPBP
R
39
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
Connect the AUDIO/VIDEO jacks between TV
1
and DVD. Match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red)
2. How to use
ᯫ
Turn on the DVD player, insert a DVD.
ᯫ
Select the AV1 or AV 2 input source on the TV
using the
ᯫ
Refer to the DVD player's manual for operating
instructions.
INPUT button on the remote control.
/DVI IN
For LED LCD TV
3
2
1
AUDIO IN
RGB IN (PC)
(RGB/DVI)
2
YPBP
1
OPTICAL DIGITAL
AUDIO OUT
VIDEO
VIDEO
R
VIDEO
RS-232C IN
(
SERVICE ONLY)
L(MONO)
AUDIO
L R
AUDIO
1
LR
AUDIO
USB IN 1USB IN 2
R
P
B
AV IN 1
R
COMPONENT IN
40
VIDEO
LR
AUDIO
COMPONENT IN3
AUDIO / Y P
H/P
IN 4
AV IN2
VIDEO / AUDIO
HDMI Connection
1. How to connect
Connect the HDMI output of the DVD to the
1
HDMI/DVI IN 1, 2, 3 or 4 jack on the TV.
No separate audio connection is necessary.
2
HDMI supports both audio and video.
2. How to use
ᯫ
Select the HDMI1, HDMI2, HDMI3, or HDMI4 input
source on the TV using the
remote control.
ᯫ
Refer to the DVD player's manual for operating
instructions.
!
NOTE
Ź If an HDMI cable doesn’t support HDMI version 1.3, it
can cause flickers or no screen display. In this case
use the latest cables that support HDMI version 1.3.
Ź
HDMI Audio Supported Format: AC3 (32KHz,
44.1KHz,48KHz), Linear PCM (32KHz, 44.1KHz,48KHz)
INPUT button on the
LAN
ꔡ
WIRELESS
CONTROL
/DVI IN
1
HDMI OUTPUT
3
2
1
(RGB/DVI)
AUDIO IN
RGB IN (PC)
OPTICAL DIGITAL
AUDIO OUT
2
YPBP
1
VIDEO
RS-232C IN
(
SERVICE ONLY)
VIDEO
R
L(MONO)
L R
AUDIO
AUDIO
EXTERNAL EQUIPMENT SETUP
R
COMPONENT INAV IN 1
41
EXTERNAL EQUIPMENT SETUP
VCR SETUP
Antenna Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
Connect the RF antenna out socket
1
of the VCR to the ANTENNA/CABLE
IN socket on the TV.
Connect the antenna cable to the RF
2
antenna in socket of the VCR.
2. How to use
ᯫ
Set VCR output switch to 3 or 4 and
then tune TV to the same channel number.
ᯫ
Insert a video tape into the VCR and
press PLAY on the VCR (Refer to the
VCR owner’s manual).
ANTENNA/
CABLE IN
1
S-VIDEO VIDEO
ANT OUT
ANT IN
OUTPUT
SWITCH
Wall Jack
2
LR
AUDIO
Antenna
42
Composite (RCA) Connection
1. How to connect
Connect the AUDIO/VIDEO jacks between TV
1
and VCR. Match the jack colors (Video = yellow,
Audio Left = white, and Audio Right = red)
2. How to use
ᯫ
Insert a video tape into the VCR and press PLAY
on the VCR. (Refer to the VCR owner’s manual.
ᯫ
Select the AV1 or AV2 input source on the TV
using the
!
NOTE
ŹIf you have a mono VCR, connect the audio cable
from the VCR to the AUDIO L/MONO jack of the TV.
INPUT button on the remote control.
For LED LCD TV
EXTERNAL EQUIPMENT SETUP
VIDEO
RS-232C IN
(
SERVICE ONLY)
VIDEO
R
L(MONO)
L R
AUDIO
AUDIO
R
AV IN 1
COMPONENT IN
RGB IN (PC)
/DVI IN
3
(RGB/DVI)
OPTICAL DIGITAL
2
AUDIO IN
AUDIO OUT
1
S
)
L
2
YPBP
1
1
ANT IN
ANT OUT
S-VIDEO
OUTPUT
SWITCH
VIDEO
LR
AUDIO
ANT IN
ANT OUT
S-VIDEO
OUTPUT
SWITCH
VIDEO
LR
AUDIO
USB IN 1USB IN 2
R
P
B
COMPONENT IN3
AUDIO / Y P
H/P
IN 4
AV IN2
VIDEO / AUDIO
43
Loading...
+ 67 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.