Please read this manual carefully before operating
your set and retain it for future reference.
32LG710H
37LG710H
42LG710H
P/NO : SAC34134301 (1107-REV05)
32LD650H
37LD650H
42LD650H
47LD650H
55LD650H
32LD655H
37LD655H
42LD655H
32LD660H
37LD660H
42LD660H
32LD665H
37LD665H
42LD665H
32LV555H
37LV555H
42LV555H
47LV555H
55LV555H
www.lg.com
WARNING / CAUTION
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating
and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING/CAUTION
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.
2
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause (harmful)
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation (of the device).
Any changes or modifications in construction of this
device which are not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
1
Clean only with a dry cloth.
2
Do not block any ventilation openings. Install in
3
accordance with the manufacturer’s instructions.
Protect the power cord from being walked on or
6
pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the
7
manufacturer.
Use only with the cart, stand, tripod, bracket, or table
8
specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from
tip-over.
Unplug this apparatus during lighting storms or
9
when unused for long periods of time.
Do not install near any heat sources such as radia-
4
tors, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.
Do not defeat the safety purpose of the polarized or
5
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong, The
wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
Refer all servicing to qualified service personnel.
10
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Never touch this apparatus or antenna during a
11
thunder or lighting storm.
When mounting a TV on the wall, make sure not to
12
install the TV by the hanging power and signal cables
on the back of the TV.
Do not allow an impact shock or any objects to fall
13
into the product, and do not drop onto the screen
with something.
3
CAUTION concerning the Power Cord :
GROUNDING
DISCONNECTING DEVICE FROM MAINS
Dot Defect
Generated Sound
OwnerMa
nual
14
It is recommend that appliances be placed upon a
dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional
outlets or branch circuits. Check the specification
page of this owner's manual to be certain.
Do not connect too many appliances to the same
AC power outlet as this could result in fire or electric shock.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire
insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically
examine the cord of your appliance, and if its
appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and
have the cord replaced with an exact replacement
part by an authorized servicer. Protect the power
cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not make the TV with the power cord plugged
in. Do not use a damaged or loose power cord. Be
sure do grasp the plug when unplugging the power
cord. Do not pull on the power cord to unplug the
TV.
Do not expose to dripping or splashing and do not
17
place objects filled with liquids, such as vases, cups,
etc. on or over the apparatus (e.g. on shelves above
the unit).
18
Ensure that you connect the earth ground wire to
prevent possible electric shock. (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grouned AC outlet) If grounding
methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it to
telephone wires, lightening rods, or gas pipes.
Short-circuit
Breaker
19
Mains plug is the disconnecting device. The plug
must remain readily operable.
Power
Supply
20
The Plasma or LCD panel is a high technology
product with resolution of two million to six million
WARNING - To reduce the risk of fire or electrical
15
shock, do not expose this product to rain, moisture
or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles or expose the
TV to direct air conditioning.
As long as this unit is connected to the AC wall out-
16
let, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
pixels. In a very few cases, you could see fine dots
on the screen while you’re viewing the TV. Those
dots are deactivated pixels and do not affect the
performance and reliability of the TV.
21
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated
by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A low
level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending
on the product.
This generated sound does not affect the performance and reliability of the product.
4
ANTENNAS
Outdoor antenna grounding
Antenna grounding according to the
National Electrical Code, ANSI/NFPA 70
Cleaning
Moving
Ventilation
For LCD TV
22
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
Ground Clamp
Electric Service
Equipment
If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can
come in contact with such power lines or circuits as
death or serious injury can occur.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges.
Section 810 of the National Electrical Code (NEC) in
the U.S.A. provides information with respect to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding
electrodes and requirements for the grounding electrode.
25
Install your TV where there is proper ventilation. Do
not install in a confined space such as a bookcase.
Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in
excessively dusty places.
Take care not to touch the ventilation openings.
26
When watching the TV for a long period, the ventilation openings may become hot.
If you smell smoke or other odors coming from the
27
TV, unplug the power cord contact and authorized
service center.
Do not press strongly upon the panel with a hand or
28
sharp object such as nail, pencil or pen, or make a
scratch on it.
NEC: National Electrical Code
23
When cleaning, unplug the po
gently with a soft cloth to prevent scratching. Do not
spray water or other liquids directly on the TV as
electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
wer cor
24
Make sure the product is turned off, unplugged
and all cables have been removed. It may take 2 or
more people to carry larger TVs. Do not press
against or put stress on the front panel of the TV.
d and scrub
Keep the product away from direct sunlight.
29
30
If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.
Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.
Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
ON DISPOSAL
(Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains
a small amount of mercury. Do not dispose of
this product with general household waste.
Disposal of this product must be carried out in
accordance to the regulations of your local authority.
5
CONTENTS
WARNING / CAUTION
SAFETY INSTRUCTIONS
FEATURES OF THIS TV
High-definition television. High-resolution digital
television broadcast and playback system composed
of roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p
resolutions.
Unlike other sensors which can only sense brightness
of ambient light, LG’s “Intelligent Sensor” uses 4,096
sensing steps to evaluate its surroundings. Using a
sophisticated algorithm, the LG processes picture
quality elements including brightness, contrast, color,
sharpness and white balance. The result is a picture
optimized for it’s surroundings, more pleasing to
watch and which can also save up to 50% in power
consumption.
View videos and photos and listen to music on your
TV through USB 2.0 (‘videos’ dependent on model).
LG TV include a unique invisible speaker system,
tuned by renowned audio expert, Mr. Mark Levinson.
Speakers are embedded in strategic spots behind the
front cabinet and use minute vibrations to turn the
entire front bezel into the speaker system. The result
is a clean, polished look, and enhanced audio by
increasing the “sweet spot”, giving a wider and richer
sound field.
Manufactured under license from Dolby Laboratories.
“
Dolby
“and the double-D symbol are trademarks of
Dolby Laboratories.
is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.
Automatically enhances and amplifies the sound of
human voice frequency range to help keep dialogue
audible when background noise swells.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."
Matches the original frame rate of the film for a more
film-like experience
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/ BURN-IN” ON YOUR TV SCREEN
■
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV
for an extended period, it can become permanently imprinted on the screen. This phenomenon is known
as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
■
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period
(2 or more hours for LCD, 1 or more hours for Plasma).
■
Image burn can also occur on the letterboxed
areas of your TV if you use the 4:3 aspect
ratio setting for an extended period.
8
PREPERATION
Optional Extras
1.5V 1.5V
MUTE
RETURN
CC
TV
POWER
GUIDE
PORTAL
ENTER
VOL
CH
123
456
78
0
9
FLASHBK
VCR
DVD
INPUT
MENU
INFO
i
STB
P
A
G
E
PIP
SAP
PIP CH-
PIP CH+
PIP SWAP
PIP INPUT
ALPHA/NUM
REMOVE
RATIO
TIMER
ABC
DEF
GHI
WXYZ
TUV
PQRS
MNO
JKL
&@
.:/,
For 32/37/42LG710H
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.
The accessories included may differ from the images below.
PREPARATION
Owner’s Manual
x 2
Torx plus
Star head screw
(Refer to P.18, P.19)
Polishing Cloth
(Not included with all
models.)
F
CD Manual
Protective Bracket and
Screw for Power Cord
(Refer to P.21, P.22)
* Wipe spots on the exterior only with the pol-
ishing cloth.
* Do not wipe roughly when removing stains.
Excessive pressure may cause scratches or
discoloration.
Remote Control,
Batteries
D-sub 15 pin Cable
Power Cord
When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.
(For 32LG710H)
x 4x 4
Screws for stand
assembly
(Refer to P.18)
Cable Holder
(Refer to P.21)
Screw for
stand fixing
(Refer to P.25)
Protection Cover
(Refer to P.18)
Plug-in type Holder
(Refer to P.21)
9
PREPARATION
For 32/37/42/47/55LD650H, 32/37/42LD655H, 32/37/42LD660H, 32/37/42LD665H
Illuminates red in standby mode.
Illuminates blue when the set is
switched on.
Remote Control Sensor
Intelligent Sensor
Adjusts picture according to the surrounding
conditions.
CH
CHANNEL
( , )
Buttons
VOL
VOLUME
(+, -)
Buttons
ENTER
ENTER
Button
H
HOME
MENU
Button
INPUT
INPUT
Button
POWER
Button
13
USBIN
AVIN2
VIDEO/AUDIO
USBIN
PREPARATION
SERVICE
ONLY
OPTICAL
DIGITAL
UPDATE
RESET
LAN 2
HDMI/DVI IN
1
INTERFACE
SPEAKER
OUT
(8 )
RGB IN (PC)
AUDIO IN
(RGB/DVI)
TV-LINK CFG
GAME CONTROL
/ MPI
RS-232C IN
(SERVICE ONLY)
AUDIO OUT
A1 NI V
AUDIO
VIDEO
MONO
/
TNENOPMOC
NI
L
R
LAN 1
RJP
ANTENNA IN
32/37/42/47/55LV555H
PREPARATION
15
918
17
1
5
4
8
6
14
11
16
11
12
13
2
7
16
1
HDMI/DVI IN
Digital Connection. Supports HD video and Digital
audio.
Accepts DVI video using an adapter or HDMI to DVI
cable (not included)
2
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).
AUDIO IN (RGB/DVI)
1/8” headphone jack for analog PC audio input.
LAN (SERVICE ONLY)
3
For connecting to a control network.
4
RESET
Performs a hardware reset.
UPDATE
Enables/disables software downloads and debug mode.
5
TV - LINK CFG
Computer input for programming Free To Guest services.
6
GAME CONTROL
Input port for third party game Controllers.
M.P. I.
Allows VOD/PPV devices or set-top boxes to control
the TV.
9
SPEAKER OUT 8
Ω
For use with external speakers.
REMOTE CONTROL OUT
10
IR output for controlling an auxiliary device.
AV (Audio/Video) IN 1/2
11
Analog composite connection. Supports standard
definition video only (480i).
COMPONENT IN
12
Analog Connection. Supports HD.
Uses a red, green, and blue cable for video & a red
and white cable for audio.
13
RJP INTERFACE (REMOTE JACK PACK PORT)
Connect this to an LG remote jack pack system.
ANTENNA IN
14
Connect an antenna to receive over-the-air (OTA)
signals.
15
Power Cord Socket
AC power input.
Caution: Never attempt to operate the TV on DC
power.
16
USB IN
Used for viewing multimedia files.
PREPARATION
7
RS-232C IN (SERVICE ONLY)
Used for software updates.
8
OPTICAL DIGITAL AUDIO OUT
Optical digital audio output for use with amps and
home theater systems.
Note: In standby mode, this port doesn’t work.
LAN
17
For connecting to a control network.
18
SERVICE ONLY
Used for software updates.
17
PREPARATION
AC
I
N
C
A
B
L
E
M
ANA
G
E
M
E
N
T
STAN D BODY
STAN D B ASE
G
!
A
C
I
N
CA
B
L
E
MA
NA
GE
M
E
N
T
prot e ction cover
PROTECTION COVER
STAND BODY
STAN D B ASE
32/37/42/47/55LV555H
PREPARATION
INSTALLATION
Carefully place the TV screen side down on a
1
cushioned surface to protect the screen from
damage.
Assemble the parts of the
2
with the
M4 x 20
Assemble the TV as shown.
3
S
of the TV.
DETACHMENT
Carefully place the TV screen side down on a
1
cushioned surface to protect the screen from
damage.
Remove the screws that hold the stand on.
2
PROTECTION COVER
After removing the stand, install the included
p
Press the
until you hear it click.
over the hole for the stand.
into the TV
20
Install the 4 screws into the holes shown.
4
M4 x 14
NOTE
When assembling the desk type stand, make sure
the screws are fully tightened (If not tightened
fully, the TV can tilt forward after the protuct
installation). Do not over tighten.
PREPARATION
G
G
DESKTOP PEDESTAL INSTALLATION
■
Image shown may differ from your TV.
PREPARATION
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
4 inches
4 inches
4 inches
CAUTION
Ensure adequate ventilation by following the clearance recommendations.
G
Do not mount near or above any type of heat source.
4 inches
SWIVEL STAND
After installing the TV, you can adjust the TV set manually to the left or right direction to suit your viewing position.
20°: 47/55LD650H
90°: Other Models
24
PREPARATION
G
G
G
ATTACHING THE TV TO A DESK
The TV should be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.
You can select any type of attachment (Type 1 or Type 2)
Do not over tighten.
Type 2
or
2-Screws, 2-Washers, 2-Nuts, 4-Rubbers
(provided as parts of the product)
Stand
Desk
25
PREPARATION
G
47/55LD650H, 47/55LV555H
PREPARATION
Stand
4-Screws
(not provided as parts of the product)
Desk
EXCEPT 47/55LD650H, 47/55LV555H
Stand
1-Screw
(provided as parts of the product)
Desk
WARNING
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
G
instructions. Tipping, shaking, or rocking the TV may cause injury.
26
VESA WALL MOUNTING
AA
BB
AA
BB
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact an installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.
PREPARATION
Model
32 LG 710 H
37LG710H,
42LG 710 H
32LD650H,
32LD655H,
32LD660H,
32LD665H,
32 LV 555H
37LD650H,
37LD655H,
37LD660H,
37LD665H,
37LV555H,
42LD650H,
42LD655H,
47LD650H
VESA (A *B)
Standard ScrewQuantity
200* 10 0M 44
200* 200M64
200* 10 0M 44
200* 200M64
Wall Mounting Bracket
(sold separately)
RW230AW-47LG30M
AW-47LG30M
LSW100B, LSW100BG
LSW200B, LSW200BG
42LD660H,
42LD665H,
42LV555H,
47LV555H
55LD650H,
55 LV 555H
400* 400M64
LSW400B, LSW400BG,
DSW400BG
27
PREPARATION
G
G
G
G
G
G
G
G
!
NOTE
PREPARATION
Screw length needed depends on the wall mount
used. For further information, refer to the instructions included with the mount.
Standard dimensions for wall mount kits are shown
in the table.
When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.
Do not use screws longer then the standard dimension, as they may cause damage to the inside of
the TV.
For wall mounts that do not comply with the VESA
standard screw specifications, the length of the
CAUTION
Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock.
screws may differ depending on their specifications.
Do not use screws that do not comply with the
VESA standard screw specifications.
Do not use fasten the screws too strongly, this may
damage the TV or cause the TV to a fall, leading to
personal injury. LG is not liable for these kinds of
accidents.
LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installation instructions.
28
SECURING THE TV TO THE WALL TO PREVENT FALLING
G
G
!
WHEN THE TV IS USED ON A STAND
■
You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).
■
Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
■
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the
bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket
that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
PREPARATION
■
Use a sturdy rope (sold separately) to tie the product. It is safer to
tie the rope so it becomes horizontal between the wall and the product.
NOTE
Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
G
To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.
29
PREPARATION
R
ANTENNA INANTENNA IN
M.P.I.
R
ANTENNA INANTENNA IN
M.P.I.
PREPARATION
■
To prevent damage, do not connect to the power outlet until all connections are made between the devices.
ANTENNA OR CABLE CONNECTION
PREPARATION
1. Antenna (Analog or Digital)
This image refers to using a Wall Antenna Socket or Outdoor
Antenna without a Cable Box Connection.
Wall
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
- For optimum picture quality, adjust the antenna direction if needed.
■
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
■
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■
If the antenna is not installed properly, contact your dealer for assistance.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
RF Coaxial Wire (75
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Ω)
Copper Wire
Be careful not to bend the copper wire
when connecting the antenna.
30
2. Cable
This image refers to using a cable connection without a cable box.
Cable TV
Wall Jack
RF Coaxial Wire (75
- If you experience a poor signal when using cable, make sure the RF cable is screwed in completely.
Contact your cable company is a poor signal persists.
Ω)
Loading...
+ 51 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.