LG 32LG710H Service Manual

LCD TV

SERVICE MANUAL

CAUTION

BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : LA95A

MODEL : 32LG710H 32LG710H-UA

North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com

Internal Use Only

Printed in KoreaP/NO : MFL62439602 (0912-REV00)

Only for training and service purposes

- 2 -

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ......................................................................... 3

SPECIFICATION....................................................................................... 6

ADJUSTMENT INSTRUCTION ................................................................ 9

EXPLODED VIEW .................................................................................. 14

SVC. SHEET ...............................................................................................

Only for training and service purposes

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to

0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument’s exposed METALLIC PARTS

Good Earth Ground such as WATER PIPE, CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

Only for training and service purposes

- 4 -

CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the

following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard.

2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its assemblies.

4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.

7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this

service manual.

CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the

unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500°F to 600°F.

2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature.

(500°F to 600°F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

(500°F to 600°F)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

SERVICING PRECAUTIONS

Only for training and service purposes

- 5 -

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.

2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and solder it.

3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor Removal/Replacement

1. Remove the defective transistor by clipping its leads as close as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

Power Output, Transistor Device Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as possible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit board.

3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional Resistor Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow stake.

2. Securely crimp the leads of replacement component around notch at stake top.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Only for training and service purposes

1. Application range

This specification is applied all of the 32”, 37”, 42” LCD TV with LA95A chassis.

2. Requirement for Test

Each part is tested as below without special appointment.

1) Temperature: 20±5ºC

2) Relative Humidity: 65±10%

3) Power Voltage : Standard input voltage(100-120V~, 50/60Hz) * Standard Voltage of each product is marked by models

4) Specification and performance of each parts are followed

each drawing and specification by part number in accordance with BOM.

5) The receiver must be operated for about 20 minutes prior to

the adjustment.

3. Test method

1) Performance: LGE TV test method followed

2) Demanded other specification

- Safety: UL, CSA, IEC specification

- EMC: FCC, ICES, IEC specification

Model Market Appliance

37LG700H-UA North America Safety : UL1492, CSA C22.2.No.1

EMC : FCC Class B, IEC Class B

- 6 -

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement.

4. General Specification(TV)

No Item Specification Remark

1 Receivable System VSB/64& 256 QAM/NTSC-M 2 Available Channel VHF : 02 ~ 13

UHF : 14 ~ 69 DTV : 02 ~ 69 CATV : 01 ~ 135

CADTV : 01 ~ 135 3 Input Voltage AC100-120V~, 50/60Hz 4 Market North America 5 Screen Size 32/37/42 Inch 6 Aspect Ratio 16:9 7 Tuning System FS 8 LCD Module EAJ59444901 V4 LC420WXE

EAJ59165501 V4 LC370WXE

EAJ58042701 V4 LC320WXN 9 Operating Environment Temp : 0 ~ 40 deg

Humidity : ~ 80 %

10 Storage Environment Temp : -20 ~ 50 deg

Humidity : 10 ~ 90 %

- 7 -

Only for training and service purposes

5. Chrominance & Luminance

No. Item Min Typ Max Unit Remarks

1 White brightness 400 500 cd/m

2 Color coordinate RED X Typ. 0.636 Typ.

(Default) Y -0.03 0.335 +0.03

GREEN X 0.290

Y 0.610

BLUE X 0.144

Y 0.063

WHITE X 0.279

Y 0.292 3 Brightness uniformity 77 % Full white 4 Contrast ratio 800:1 1200:1 5 Dynamic CR 50000:1 100000:1 Applied condition:vivid

(except RGB, DVI/PC format)

6 Color Temperature Cool x:0.274 x:0.276 x:0.278 oK The W/B Tolerance is

y:0.281 y:0.283 y:0.285 ±0.015 for Adjustment

Medium x:0.283 x:0.285 x:0.287

y:0.291 y:0.293 y:0.295

Warm x:0.311 x:0.313 x:0.315

y:0.327 y:0.329 y:0.331 7 Color Distortion, DG 10.0 % 8 Color Distortion, DP 10.0 deg 9 Color S/N, AM/FM 43.0 dB

10 Color Killr Sensitivity -80 dBm

6. Component Video Input (Y, CB/PB, CR/PR)

No Resolution H-freq(kHz) V-freq.(kHz) Proposed

1 720*480 15.73 60 SDTV ,DVD 480I 2 720*480 15.73 59.94 SDTV ,DVD 480I 3 720*480 31.47 60 SDTV 480P 4 720*480 31.47 59.94 SDTV 480P 5 1280*720 45.00 60.00 HDTV 720P 6 1280*720 44.96 59.94 HDTV 720P 7 1920*1080 33.75 60.00 HDTV 1080I 8 1920*1080 33.72 59.94 HDTV 1080I

Only for training and service purposes

- 8 -

7. RGB Input (PC)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed

PC DDC

1. 640*350 31.468 70.09 25.17 EGA X

2. 720*400 31.469 70.08 28.32 DOS O

3. 640*480 31.469 59.94 25.17 VESA(VGA) O

4. 640*480 37.861 72.80 31.50 VESA(VGA) O

5. 800*600 37.879 60.31 40.00 VESA(SVGA) O

6. 800*600 48.077 72.18 50.00 VESA(SVGA) O

7. 1024*768 48.363 60.00 65.00 VESA(XGA) O

8. 1024*768 56.476 70.06 75.00 VESA(XGA) O

9. 1280*768 47.776 59.870 79.5 CVT(WXGA) O

10. 1280*768 60.289 74.893 102.25 CVT(WXGA) O

11. 1360*768 47.712 60.015 85.50 VESA (WXGA) O

12. 1280*1024 63.981 60.020 108.00 VESA (SXGA) O

13. 1280*1024 79.976 75.025 135 VESA (SXGA) O

14. 1600*1200 75.000 60.000 162 VESA(UXGA) X

8. HDMI input (PC/DTV)

No Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed

PC DDC 1 640*350 31.468 70.09 25.17 EGA X 2 720*400 31.469 70.08 28.32 DOS O 3 640*480 31.469 59.94 25.17 VESA(VGA) O 4 800*600 35.156 56.25 36.00 VESA(SVGA) O 5 800*600 37.879 60.31 40.00 VESA(SVGA) O 6 800*600 48.077 72.18 50.00 VESA(SVGA) O 7 800*600 46.875 75.00 49.50 ESA(SVGA) O 8 1024*768 48.363 60.00 65.00 VESA(XGA) O 9 1024*768 56.476 70.06 75.00 VESA(XGA) O

10 1024*768 60.023 75.02 78.75 VESA(XGA) O 11 1280*768 47.776 59.870 79.5 CVT(WXGA) O 12 1360*768 47.712 60.015 85.50 VESA (WXGA) O 13 1280*1024 63.981 60.020 108.00 VESA (SXGA) O 14 1280*1024 79.976 75.025 135 VESA (SXGA) O 15 1600*1200 75.000 60.000 162 VESA(UXGA) X 16 1920*1080 67.500 60.000 148.5 HDTV 1080P X

DTV

1 720*480 31.47 60 27.027 SDTV 480P O 2 720*480 31.47 59.94 27.00 SDTV 480P O 3 1280*720 45.00 60.00 74.25 HDTV 720P O 4 1280*720 44.96 59.94 74.176 HDTV 720P O 5 1920*1080 33.75 60.00 74.25 HDTV 1080I O 6 1920*1080 33.72 59.94 74.176 HDTV 1080I O 7 1920*1080 67.500 60 148.50 HDTV 1080P X 8 1920*1080 67.432 59.939 148.352 HDTV 1080P X 9 1920*1080 27.000 24.000 74.25 HDTV 1080P X

10 1920*1080 26.97 23.94 74.176 HDTV 1080P X 11 1920*1080 33.75 30.000 74.25 HDTV 1080P X 12 1920*1080 33.71 29.97 74.176 HDTV 1080P X

Only for training and service purposes

- 9 -

ADJUSTMENT INSTRUCTION

1. Application Object

This specification sheet applied to LA95A Chassis applied LCD TV all models manufactured in TV factory.

2. Notes

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation

transformer will help protect test equipment. (2) Adjustments must be done in the correct order. (3) The adjustments must be performed in the circumstance of

20±5°C of temperature and 65±10% of relative humidity if

there is no specific designation. (4) The input voltage of the receiver be must kept 100V-240V,

50/60Hz when adjusting. (5) The receiver must be operated for about 5 minutes prior to

the adjustment when module is in the circumstance of over

15. In case of keeping module is in the circumstance of 0°C, it should be placed in the circumstance of above 15°C for 2 hours In case of keeping module is in the circumstance of below 20°C, it should be placed in the circumstance of above 15°C for 3 hours,.

Caution : When still image is displayed for a period of 20 minutes or longer (especially where W/B scale is strong. Digital pattern 13ch and/or Cross hatch pattern 09ch), there can some afterimage in the black level area.

3. Adjustment items

3.1. Main PCB check process

- Adjust 480i Comp1

- Adjust 1024*768 RGB Above adjustment items can be also performed in Final

Assembly if needed. Both Board-level and Final assembly adjustment items can be check using In-Star Menu 1.ADJUST CHECK.

3.2. Final assembly adjustment

- EDID/DDC download

- White Balance adjustment

- RS-232C functionality check

- Factory Option setting per destination

- Ship-out mode setting (In-Stop)

3.3 Etc

- Ship-out mode

- Service Option Default

- USB Download(S/W Update, Option, Service only)

- ISP Download(Option)

4. Automatic Adjustment

4.1. ADC Adjustment

(1) Overview

ADC adjustment is needed to find the optimum black level and gain in Analog-to-Digital device and to compensate RGB deviation.

(2) Equipment & Condition

1) Jig (RS-232C protocol)

2) MSPG-925 Series Pattern Generator(MSPG-925FA)

- Resolution : 480i Comp1 (MSPG-925FA: model-209, pattern-65) 1024*768 RGB (MSPG-925FA: model-60 , pattern-65)

- Pattern : Horizontal 100% Color Bar Pattern

- Pattern level : 0.7±0.1 Vp-p

- Image

(3) Adjustment

1) Adjustment method

- Using RS-232, adjust items listed in 3.1 in the other shown in “4.1.3.3”

2) Adj. protocol

Ref.) ADC Adj. RS232C Protocol_Ver1.0

3) Adj. order

- aa 00 00 [Enter ADC adj. mode]

- xb 00 40 [Change input source to Component1(480i)]

- ad 00 10 [Adjust 480i Comp1]

- xb 00 60 [Change input source to RGB(1024*768)]

- ad 00 10 [Adjust 1024*768 RGB]

- ad 00 90 End adj.

Protocol Command Set ACK Enter adj. mode aa 00 00 a 00 OK00x Source change xb 00 40 b 00 OK40x (Adjust 480i Comp1 )

xb 00 60 b 00 OK60x (Adjust 1024*768 RGB) Begin adj. ad 00 10 Return adj. result OKx (Case of Success)

NGx (Case of Fail)

Read adj. data (main) (main)

ad 00 20 000000000000000000000000007c007b006dx

(sub) (Sub)

ad 00 21 000000070000000000000000007c00830077x Confirm adj. ad 00 99 NG 03 00x (Fail)

NG 03 01x (Fail) NG 03 02x (Fail) OK 03 03x (Success)

End adj. aa 00 90 a 00 OK90x

- 10 -

Only for training and service purposes

(2) Confirmation

1) We confirm whether “0xBF(480i)/0xC8(1080i)” address of EEPROM “0xA2” is “0xAA” or not.

2) If “0xBF(480i)/0xC8(1080i)” address of EEPROM “0xA2” isn’t “0xAA”, we adjust once more.

3) We can confirm the ADC values from “0xB ~0xBE(480i)/ 0xC2~(1080i)” addresses in a page “0xA2”.

* Manual ADC Confirmation using Service Remocon. After

enter Service Mode by pushing “INSTART” key.

5. Manual Adjustment

5.1. ADC(Saturn5) Adjustment

(1) Overview

ADC adjustment is needed to find the optimum black level and gain in Analog-to-Digital device and to compensate RGB deviation.

(2) Equipment & Condition

1) Adjust Remocon

2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern Generator

- Resolution: 480i, 1024*768

- Pattern : Horizontal 100% Color Bar Pattern

- Pattern level: 0.7±0.1 Vp-p

- Image

3) Must use standard cable

(3) Adjust method

• ADC 480i Comp1

1) Check connected condition of Comp1 cable to the equipment

2) Give a 480i Mode, Horizontal 100% Color Bar Pattern to Comp1.

(MSPG-925FA -> Model: 209, Pattern: 65)

3) Change input mode as Component1 and picture mode as “Standard”

4) Press the In-start Key on the ADJ remote after at least 1 min of signal reception. Then, select 7. External ADC

-> 1. COMP 480i on the menu. Press enter key. The adjustment will start automatically.

5) If ADC calibration is successful, “ADC RGB Success” is displayed.

If ADC calibration is failure, “ADC RGB Fail” is displayed.

6) If ADC calibration is failure, after recheck ADC pattern or condition retry calibration. Error message refer to (v)

• ADC 1024*768 RGB

1) Check connected condition of Component & RGB cable to the equipment

2) Give a 1024*768 Mode, 100% Horizontal Color Bar Pattern to RGB port.

(MSPG-925 Series Ë model:60 , pattern:65 )

3) Change input mode as RGB and picture mode as “Standard”

4) Press the In-start Key on the ADJ remote after at least 1 min of signal reception. Then, select 7. External ADC

-> 1. COMP 480i on the menu. Press enter key. The adjustment will start automatically.

5) If ADC calibration is successful, “ADC RGB Success” is displayed.

If ADC calibration is failure, “ADC RGB Fail” is displayed.

6) If ADC calibration is failure, after recheck ADC pattern or condition retry calibration

Error message refer to 5)

5.2. EDID(The Extended Display Identification Data)/DDC(Display Data Channel) download

Reference : Download is only possible in POWER ONLY

MODE

(1) Overview

It is a VESA regulation. A PC or a MNT will display an optimal resolution through information sharing without any necessity of user input. It is a realization of “Plug and Play”.

(2) Equipment

- Since embedded EDID data is used, EDID download JIG, HDMI cable and D-sub cable are not need.

- Adjust remocon

(3)Download method

1) Press Adj. key on the Adj. R/C,

2) Select EDID D/L menu.

3) By pressing Enter key, EDID download will begin

4) If Download is successful, OK is display, but If

Download is failure, NG is displayed.

5) If Download is failure, Re-try download.

Caution) When EDID download, must remove RGB/HDMI cable.

- 11 -

Only for training and service purposes

(4) EDID DATA

1) HDMI 1 [C/S: 5024]

- EDID Block 0 table =

- EDID Block 1 table =

2) HDMI 2 [C/S: 5014]

- EDID Block 0 table =

- EDID Block 1 table =

3) RGB [C/S: 9B]

- EDID Block 0 table =

5.3. White Balance Adjustment

(1) Overview

• W/B adj. Objective & How-it-works

- Objective: To reduce each Panel’s W/B deviation

- How-it-works: When R/G/B gain in the OSD is at 192, it

means the panel is at its Full Dynamic Range. In order to prevent saturation of Full Dynamic range and data, one of R/G/B is fixed at 192, and the other two is lowered to find the desired value.

- Adj. condition : normal temperature

1) Surrounding Temperature: 25±5ºC

2) Warm-up time: About 5 Min

3) Surrounding Humidity: 20% ~ 80%

(2) Equipment

1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12)

2) Adj. Computer(During auto adj., RS-232C protocol is

needed)

3) Adjust Remocon

4) Video Signal Generator MSPG-925F 720p/216-Gray

(Model:217, Pattern:78)

-> Only when internal pattern is not available

• Color Analyzer Matrix should be calibrated using CS-1000

(3) Equipment connection MAP

(4) Adj. Command (Protocol)

1) RS-232C Command used during auto-adj.

Ex) wb 00 00 -> Begin white balance auto-adj.

wb 00 10 -> Gain adj. ja 00 ff -> Adj. data jb 00 c0 ...

... wb 00 1f -> Gain adj. complete *(wb 00 20(start), wb 00 2f(end)) -> Off-set adj. wb 00 ff -> End white balance auto adj.

Colo r Analyzer

Comp ut er

Pattern Ge n e r ator

RS-232C

Probe

Signal Source

* If TV internal pattern is used, not needed

Connection Diagram of Automatic Adjustment

RS-232C COMMAND

Meaning

[CMD ID DATA] wb 00 00 Begin White Balance adj. wb 00 ff End White Balance adj.(Internal pattern disappeared)

- 12 -

Only for training and service purposes

2) Adjustment Map

(5) Adj. method

• Auto adj. method

1) Set TV in adj. mode using POWER ON key

2) Zero calibrate probe then place it on the center of the Display

3) Connect Cable(RS-232C)

4) Select mode in adj. Program and begin adj.

5) When adj. is complete (OK Sing), check adj. status pre mode (Warm, Medium, Cool)

6) Remove probe and RS-232C cable to complete adj.

* W/B Adj. must begin as start command “wb 00 00”, and

finish as end command “wb 00 ff”, and Adj. offset if need

• Manual adj. method

1) Set TV in Adj. mode using POWER ON

2) Zero Calibrate the probe of Color Analyzer, then place it on the center of LCD module within 10cm of the surface..

3) Press ADJ key -> EZ adjust using adj. R/C > 6. WhiteBalance then press the cursor to the right (KEY

G).

(When KEY(

G) is pressed 216 Gray internal pattern

will be displayed)

4) One of R Gain / G Gain / B Gain should be fixed at 192, and the rest will be lowered to meet the desired value.

5) Adj. is performed in COOL, MEDIUM, WARM 3 modes of color temperature.

- If internal pattern is not available, use RF input. In EZ

Adj. menu 6.White Balance, you can select one of 2 Test-pattern: ON, OFF. Default is inner(ON). By selecting OFF, you can adjust using RF signal in 216 Gray pattern.

* Adj. condition and cautionary items

1) Lighting condition in surrounding area Surrounding lighting should be lower 10 lux. Try to isolate adj. area into dark surrounding.

2) Probe location

- LCD: Color Analyzer (CA-210) probe should be

within 10cm and perpendicular of the module surface (80°~ 100°)

3) Aging time

- After Aging Start, Keep the Power ON status during 5

Minutes.

- In case of LCD, Back-light on should be checked

using no signal or Full-white pattern.

(6) Reference (White Balance Adj. coordinate and color

temperature)

• Luminance: 216 Gray

• Standard color coordinate and temperature using CS1000 (over 26 inch)

• Standard color coordinate and temperature using CA210(CH 9)

5.4. HDCP SETTING

- HDCP setting is not necessary in Saturn5 model.

5.5 Option selection per country

(1) Overview

- Option selection is only done for models in Non-USA North America due to rating

- Applied model: LA92A Chassis applied None USA model(CANADA, MEXICO)

(2) Method

1) Press ADJ key on the Adj. R/C, then select Country

Group Menu

2) Depending on destination, select KR or US, then on the

lower Country option, select US, CA, MX. Selection is done using +, - KEY

ITEM Command Data Range Default

(Hex.) (Decimal)

Cmd 1 Cmd 2 Min Max

Cool R-Gain j g 00 C0

G-Gain j h 00 C0 B-Gain j i 00 C0 R-Cut G-Cut B-Cut

Medium R-Gain j a 00 C0

G-Gain j b 00 C0 B-Gain j c 00 C0 R-Cut G-Cut B-Cut

Warm R-Gain j d 00 C0

G-Gain j e 00 C0 B-Gain j f 00 C0 R-Cut G-Cut

Mode Color Coordination Temp ∆UV

COOL 0.276 0.283 11000K 0.0000

MEDIUM 0.285 0.293 9300K 0.0000

WARM 0.313 0.329 6500K 0.0000

Mode Color Coordination Temp ∆UV

COOL 0.276±0.002 0.283±0.002 11000K 0.0000

MEDIUM 0.285±0.002 0.293±0.002 9300K 0.0000

WARM 0.313+0.002 0.329±0.002 6500K 0.0000

Only for training and service purposes

- 13 -

5.6. Tool Option selection

• Method: Press Adj. key on the Adj. R/C, then select Tool option.

5.7. Ship-out mode check (In-stop)

• After final inspection, press In-Stop key of the Adj. R/C and check that the unit goes to Stand-by mode.

• After final inspection, Always turn on the Mechanical S/W.

6. GND and Internal Pressure check

6.1. Method

1) GND & Internal Pressure auto-check preparation

- Check that Power Cord is fully inserted to the SET. (If loose, re-insert)

2) Perform GND & Internal Pressure auto-check

- Unit fully inserted Power cord, Antenna cable and A/V arrive to the auto-check process.

- Connect D-terminal to AV JACK TESTER

- Auto CONTROLLER(GWS103-4) ON

- Perform GND TEST

- If NG, Buzzer will sound to inform the operator.

- If OK, changeover to I/P check automatically. (Remove CORD, A/V form AV JACK BOX)

- Perform I/P test

- If NG, Buzzer will sound to inform the operator.

- If OK, Good lamp will lit up and the stopper will allow the pallet to move on to next process.

6.2. Checkpoint

• TEST voltage

- GND: 1.5KV/min at 100mA

- SIGNAL: 3KV/min at 100mA

• TEST time: 1 second

• TEST POINT

- GND TEST = POWER CORD GND & SIGNAL CABLE METAL GND

- Internal Pressure TEST = POWER CORD GND & LIVE & NEUTRAL

• LEAKAGE CURRENT: At 0.5mArms

7. USB S/W Download (option)

(1) Put the USB Stick to the USB socket (2) Automatically detecting update file in USB Stick

- If your downloaded program version in USB Stick is Low, it didn’t work. But your downloaded version is High, USB data is automatically detecting

(3) Show the message “Copying files from memory”

(4) Updating is staring.

(5) Updating Completed, The TV will restart automatically (6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage)

* If downloading version is more high than your TV have,

TV can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didn’t have a DTV/ATV test on production line.

* After downloading, have to adjust TOOL OPTION again.

1) Push "IN-START" key in service remote controller.

2) Select "Tool Option 1" and Push “OK” button.

3) Punch in the number. (Each model has their number.)

Model Tool 1 Tool 2 Tool 3 Tool 4 Menu 32LG710H 17921 1576 35104 0 2 HDMI, CAN Tuner, 2RCA 37LG710H 22017 1576 35104 0 2 HDMI, CAN Tuner, 2RCA 42LG710H 26113 1576 35104 0 2 HDMI, CAN Tuner, 2RCA

Only for training and service purposes

- 14 -

300

200

121

500

120

122

400

800

801

802

804

803

530

521

821

805

550

910

900

540

820

822

510

560

570

EXPLODED VIEW

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

+ 38 hidden pages