OWNER’S MANUAL
Safety and Reference
Please read this manual carefully before operating your set and retain it for future reference.
*MFL68702213* |
www.lg.com |
P/NO : MFL68702213 (1502-REV00) |
|
|
Printed in Korea |
<![endif]>ENGLISH
Safety instructions
Please read these safety precautions carefully before using the product.
WARNING
Do not place the TV and/or remote control in the following environments:
t A location exposed to direct sunlight
t An area with high humidity such as a bathroom
tNear any heat source such as stoves and other devices that produce heat
tNear kitchen counters or humidi!ers where they can easily be exposed to steam or oil
t An area exposed to rain or wind
t Near containers of water such as vases
Otherwise, this may result in !re, electric shock, malfunction or product deformation.
Do not place the product where it might be exposed to dust. This may cause a !re hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains electric supply. This plug must remain readily attached and operable when TV is in use.
Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust o". You may be electrocuted due to excess moisture.
Make sure to connect Mains cable to compliant AC mains socket with Grounded earth pin. (Except for devices which are not grounded on earth.) Otherwise possibility you may be electrocuted or injured.
Insert power cable plug completely into wall socket otherwise if not secured completely into socket, !re ignition may break out.
Ensure the power cord does not come into contact with hot objects such as a heater. This may cause a !re or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables. Otherwise, this may result in !re or electric shock.
Bend antenna cable between inside and outside building to prevent rain from #owing in. This may cause water damaged inside the Product and could give an electric shock.
When mounting TV onto wall make sure to neatly install and isolate cabling from rear of TV as to not create possibility of electric shock / !re hazard.
2
Do not plug too many electrical devices into a single multiple electrical outlet. Otherwise, this may result in •re due to over-heating.
Do not put or store in"ammable substances near the product. There is a danger of combustion/explosion or •re due to careless handling of the in"ammable substances.
<![endif]>ENGLISH
Do not drop the product or let it fall over when connecting external devices. Otherwise, this may result in injury or damage to the product.
DESICCANT
Keep the anti-moisture packing material or vinyl packing out of the reach of children. Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause su!ocation. Keep it out of the reach of children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not consume them. Please seek DoctorMedical Attention immediately if child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/ cutlery/screwdriver) between power cable plug and input Wall Socket while it is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into the wall input terminal. You may be electrocuted. (Depending on model)
Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the product, or in"ammable objects such as paper and matches. Children must pay particular attention. Electrical shock, •re or injury can occur. If a foreign object is dropped into the product, unplug the power cord and contact the service centre.
Do not spray water on the product or scrub with an in"ammable substance (thinner or benzene). Fire or electric shock accident can occur.
Do not allow any impact, shock or any objects to fall into the unit, and do not drop anything onto the screen. You may be injured or the product can be damaged.
Never touch this product or antenna during a thunder or lighting storm. You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the windows and ventilate. It may cause a •re or a burn by a spark.
3
<![endif]>ENGLISH
Do not disassemble, repair or modify the product at your own discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
If any of the following occur, unplug the product immediately and contact your local service centre.
t The product has been impacted by shock t The product has been damaged
t Foreign objects have entered the product
t The product produced smoke or a strange smell This may result in •re or electric shock.
Unplug the TV from AC mains wall socket if you do not intend to use the TV for a long period of time. Accumulated dust can cause •re hazard and insulation deterioration can cause electric leakage/shock/•re.
Apparatus shall not be exposed to dripping or splashing and no objects •lled with liquids, such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.
If water or another substance enters the product (like a AC adapter, power cord, TV), disconnect the power cord and contact the service centre immediately. Otherwise, this may result in •re or electric shock.
Only use an authorized AC adapter and power cord approved by LG Electronics. Otherwise, this may result in •re, electric shock, malfunction or product deformation.
Never Disassemble the AC adapter or power cord.
This may result in •re or electric shock.
CAUTION
Install the product where no radio wave occurs.
There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. This may cause an electric shock.
Do not install the product on places such as unstable shelves or inclined surfaces. Also avoid places where there is vibration or where the product cannot be fully supported. Otherwise, the product may fall or "ip over, which may cause injury or damage to the product.
If you install the TV on a stand, you need to take actions to prevent the product from overturning. Otherwise, the product may fall over, which may cause injury.
If you intend to mount the product to a wall, attach VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), •x it carefully so as not to drop.
4
Only use the attachments / accessories speci•ed by the manufacturer.
When installing the antenna, consult with a quali•ed service technician. If not installed by a quali•ed technician, this may create a •re hazard or an electric shock hazard.
We recommend that you maintain a distance of at least 2 to 7 times the diagonal screen size when watching TV. If you watch TV for a long period of time, this may cause blurred vision.
Only use the speci•ed type of battery. This could cause damage to the remote control.
Do not mix new batteries with old batteries. This may cause the batteries to overheat and leak.
Batteries should not be exposed to excessive heat. For example, keep away from direct Sunlight , open •replace and electric heaters.
Do not place non-rechargeable batteries in charging device.
Make sure there are no objects between the remote control and its sensor.
Signal from Remote Control can be interrupted due to external/internal lighting eg Sunlight, !uorescent lighting. If this occurs turn o" lighting or darken viewing area.
When connecting external devices such as video game consoles, make sure the connecting cables are long enough. Otherwise, the product may fall over, which may cause injury or damage the product.
Do not turn the product On/O" by plugging-in or unplugging the power plug to the wall outlet. (Do not use the power plug for switch.) It may cause mechanical failure or could give an electric shock.
Please follow the installation instructions below to prevent the product from overheating.
tThe distance between the product and the wall should be more than 10 cm.
tDo not install the product in a place with no ventilation (e.g., on a bookshelf or in a cupboard).
t Do not install the product on a carpet or cushion.
t Make sure the air vent is not blocked by a tablecloth or curtain. Otherwise, this may result in •re.
Take care not to touch the ventilation openings when watching the TV for long periods as the ventilation openings may become hot. This does not a"ect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Prevent dust collecting on the power plug pins or outlet. This may cause a •re hazard.
<![endif]>ENGLISH
5
<![endif]>ENGLISH
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it, as it may cause damage to screen.
Avoid touching the screen or holding your •nger(s) against it for long periods of time. Doing so may produce some temporary or permanent distortion/damage to screen.
When cleaning the product and its components, unplug the power •rst and wipe it with a soft cloth. Applying excessive force may cause scratches or discolouration. Do not spray with water or wipe with a wet cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax, benzene, alcohol etc., which can damage the product and its panel. Otherwise, this may result in •re, electric shock or product damage (deformation, corrosion or breakage).
When moving the product, make sure you turn the power o! •rst. Then, unplug the power cables, antenna cables and all connecting cables. The TV set or power cord may be damaged, which may create a •re hazard or cause electric shock.
When moving or unpacking the product, work in pairs because the product is heavy. Otherwise, this may result in injury.
Contact the service centre once a year to clean the internal parts of the product.
Accumulated dust can cause mechanical failure.
Refer all servicing to quali•ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn o! this unit by SWITCH.
When unplugging the cable, grab the plug and unplug it, by pulling at the plug.
Don’t pull at the cord to unplug the power cord from the power board, as this could be hazardous.
If the product feels cold to the touch, there may be a small“"icker” when it is turned on. This is normal, there is nothing wrong with product.
The panel is a high technology display with resolution of two million to eight million pixels. You may see tiny black dots and/or brightly coloured dots (red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and does not a!ect the performance and reliability of the product.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
6
You may •nd di!erent brightness and color of the panel depending on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not related with the product performance, and it is not malfunction.
* LG LED TVs are LCD TVs with LED backlighting.
Displaying a still image (e.g., broadcasting channel logo, on-screen menu, scene from a video game) for a prolonged time may cause damage to the screen, resulting in retention of the image, which is known as image sticking. The warranty does not cover the product for image sticking.
Avoid displaying a •xed image on your television’s screen for a prolonged period (2 or more hours for LCD, 1 or more hours for Plasma). Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking may occur on the borders of the panel.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
Generated sound
“Cracking”noise: A cracking noise that occurs when watching or turning o! the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product.
This generated sound does not a!ect the performance and reliability of the product.
Do not use high voltage electrical goods near the TV(e.g. electric mosquito-swatter). This may result in product malfunction.
Viewing 3D imaging (Only 3D models)
WARNING
Viewing environment
t Viewing Time
- When watching 3D contents, take 5 - 15 minute breaks every hour. Viewing 3D contents for a long period of time may cause headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or chronic illness
t Some users may experience a seizure or other abnormal symptoms when they are exposed to a "ashing light or particular pattern from 3D contents.
t Do not watch 3D videos if you feel nausea, are pregnant and/ or have a chronic illness such as epilepsy, cardiac disorder, or blood pressure disease, etc.
t3D Contents are not recommended to those who su!er from stereo blindness or stereo anomaly. Double images or discomfort in
viewing may be experienced.
tIf you have strabismus (cross-eyed), amblyopia (weak eyesight) or astigmatism, you may have trouble sensing depth and easily feel
fatigue due to double images. It is advised to take frequent breaks than the average adult.
tIf your eyesight varies between your right and left eye, correct your eyesight prior to watching 3D contents.
Symptoms which require discontinuation or refraining from watching 3D contents
t Do not watch 3D contents when you feel fatigue from lack of sleep, overwork or drinking.
tWhen these symptoms are experienced, stop using/watching 3D contents and get enough rest until the symptom subsides.
-Consult your doctor when the symptoms persist. Symptoms may include headache, eyeball pain, dizziness, nausea, palpitation, blurriness, discomfort, double image, visual inconvenience or fatigue.
<![endif]>ENGLISH
7
<![endif]>ENGLISH
CAUTION
Viewing environment
tViewing Distance
-Maintain a distance of at least twice the screen diagonal length when watching 3D contents. If you feel discomfort in viewing 3D contents, move further away from the TV.
Viewing age
tInfants/Children
-Usage/ Viewing 3D contents for children under the age of 6 are prohibited.
-Children under the age of 10 may overreact and become overly excited because their vision is in development (for example: trying to touch the screen or trying to jump into it.) Special monitoring and extra attention is required for children watching 3D contents.
-Children have greater binocular disparity of 3D presentations than adults because the distance between the eyes is shorter than that of adults. Therefore they will perceive more stereoscopic depth compared to adults for the same 3D image.
tTeenagers
-Teenagers under the age of 19 may react with sensitivity due to stimulation from light in 3D contents. Advise them to refrain from watching 3D contents for a long time when they are tired.
tElderly
-The elderly may perceive less 3D effect compared to the young. Do not sit closer to the TV than the recommended distance.
Cautions when using the 3D glasses
t Make sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly.
tDo not use 3D glasses instead of your normal glasses, sunglasses or protective goggles.
t Using modi!ed 3D glasses may cause eye strain or image distortion.
tDo not keep your 3D glasses in extremely high or low temperatures. It will cause deformation.
tThe 3D glasses are fragile and are easily scratched. Always use a soft, clean piece of cloth when wiping the lenses. Do not scratch the lenses of the 3D glasses with sharp objects or clean/wipe them with chemicals.
Preparing
NOTE
t If the TV is turned on for the !rst time after it was shipped from the factory, initialization of the TV may take a few minutes.
t Image shown may di"er from your TV.
t Your TV’s OSD (On Screen Display) may di"er slightly from that shown in this manual.
tThe available menus and options may di"er from the input source or product model that you are using.
t New features may be added to this TV in the future.
tThe TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned o" if it will not be
watched for some time, as this will reduce energy consumption.
tThe energy consumed during use can be signi!cantly reduced if the level of brightness of the picture is reduced, and this will reduce
the overall running cost.
t The items supplied with your product may vary depending on the model.
tProduct speci!cations or contents of this manual may be changed without prior notice due to upgrade of product functions.
tFor an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not !t into your TV’s USB port.
|
B |
B |
|
|
< |
10 mm |
|
|
|
||
|
|
*A = |
|
A |
A |
< |
18 mm |
*B = |
t Use a certi!ed cable with the HDMI logo attached.
tIf you do not use a certi!ed HDMIcable, the screen may not display or a connection error may occur. (Recommended HDMICable Types)
-High-Speed HDMI®/TM Cable (3m or less)
-High-Speed HDMI®/TM Cable with Ethernet (3m or less)
CAUTION
tDo not use any unapproved items to ensure the safety and product life span.
t Any damage or injuries caused by using unapproved items are not covered by the warranty.
tSome models have a thin !lm attached on to the screen and this must not be removed.
8
Separate purchase |
Lifting and moving the TV |
Separate purchase items can be changed or modi•ed for quality improvement without any noti•cation. Contact your dealer to buy these items. These devices only work with certain models.
The model name or design may be changed depending on the upgrade of product functions, manufacturer’s circumstances or policies.
(Depending on model)
AG-F*** |
AN-MR600 |
AN-VC550 |
Cinema 3D Glasses |
Magic Remote |
Smart Camera |
|
|
|
AG-F***DP |
LG Audio Device |
|
Dual Play Glasses |
|
|
|
|
|
Maintenance
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
tMake sure to turn the power o! and disconnect the power cord and all other cables •rst.
tWhen the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild detergent. Then wipe immediately with a dry cloth.
tAvoid touching the screen at all times, as this may result in damage to the screen.
t Do not push, rub, or hit the screen surface with your •ngernail or a sharp object, as this may result in scratches and image distortions.
t Do not use any chemicals as this may damage the product.
tDo not spray liquid onto the surface. If water enters the TV, it may result in •re, electric shock, or malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.
t It is recommended to move the TV in the box or packing material that the TV originally came in.
tBefore moving or lifting the TV, disconnect the power cord and all cables.
tWhen holding the TV, the screen should face away from you to avoid damage.
tHold the top and bottom of the TV frame •rmly. Make sure not to hold the transparent part, speaker, or speaker grill area.
t When transporting a large TV, there should be at least 2 people.
tWhen transporting the TV by hand, hold the TV as shown in the following illustration.
tWhen transporting the TV, do not expose the TV to jolts or excessive vibration.
tWhen transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right.
t Do not apply excessive pressure to cause "exing /bending of frame chassis as it may damage screen.
tWhen handling the TV, be careful not to damage the protruding joystick button.
CAUTION
t Avoid touching the screen at all times, as this may result in damage to the screen.
tDo not move the TV by holding the cable holders, as the cable holders may break, and injuries and damage to the TV may occur.
<![endif]>ENGLISH
9
<![endif]>ENGLISH
Using the joystick button |
Mounting on a table |
You can simply operate the TV functions, pressing or moving the joystick button up, down, left or right.
Joystick Button
(Depending on model)
1 Lift and tilt the TV into its upright position on a table.
tLeave a 10 cm (minimum) space from the wall for proper ventilation.
|
10 cm |
|
|
cm |
|
10 cm |
10 |
|
10 cm |
||
|
||
|
10 cm |
Basic functions
|
|
|
|
When the TV is turned o!, place your |
|
|
|
Power On |
•nger on the joystick button and |
|
|
|
||
|
|
|
|
press it once and release it. |
|
|
|
|
When the TV is turned on, place |
|
|
|
|
your •nger on the joystick button |
|
|
|
Power O! |
and press it once for a few seconds |
|
|
|
||
|
|
|
and release it. All running apps will |
|
|
|
|
|
|
|
|
|
|
close, and any recording in progress |
|
|
|
|
will stop. |
|
|
|
|
If you place your •nger over the |
|
|
|
Volume |
joystick button and move it left or |
|
|
|||
|
|
|
Control |
right, you can adjust the volume level |
|
|
|
|
you want. |
|
|
|
|
If you place your •nger over the |
|
|
|
Programmes |
joystick button and move it up or |
|
|
|||
|
|
|
Control |
down, you can scrolls through the |
|
|
|
|
saved programmes you want. |
Adjusting the menu
When the TV is turned on, press the joystick button one time. You can adjust the Menu items moving the joystick button up, down, left or right.
Turns the power o!.
Clears on-screen displays and returns to TV viewing.
Changes the input source. |
Accesses the quick settings. |
NOTE
tWhen your •nger over the joystick button and push it to the up, down, left or right, be careful not to press the joystick button. If you press the joystick button •rst, you may not be able to adjust the volume level and saved programmes.
2 Connect the power cord to a wall outlet.
CAUTION
tDo not place the TV near or on sources of heat, as this may result in •re or other damage.
Using the kensington security system
(This is not available for all models.)
t Image shown may di!er from your TV.
The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www. kensington.com. Connect the Kensington security system cable between the TV and a table.
Securing the TV to a wall
(This feature is not available for all models.)
10
1Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV.
tIf there are bolts inserted at the eye-bolts position, remove the bolts •rst.
2Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear of the TV.
3Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the "at surface.
CAUTION
t Make sure that children do not climb on or hang on the TV.
NOTE
tUse a platform or cabinet that is strong and large enough to support the TV securely.
tBrackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solid wall perpendicular to the "oor. When you attach the TV to other building materials, please contact quali•ed personnel. LG recommends that wall mounting be performed by a quali•ed professional installer. We recommend the use of LG’s wall mount bracket. When you do not use LG’s wall mount
bracket, please use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.
Separate purchase(Wall mounting bracket)
Model |
32/40/43LF63** |
49/55LF63** |
|||||
32LF65** |
|||||||
|
|
||||||
VESA (A x B) |
|
|
200 x 200 |
300 x 300 |
|||
|
|
|
|
|
|
|
|
Standard screw |
|
|
|
M6 |
M6 |
||
|
|
|
|
|
|
|
|
Number of screws |
4 |
|
4 |
||||
|
|
|
|
|
|
|
|
Wall mount bracket |
|
|
LSW240B |
LSW350B |
|||
|
|
MSW240 |
MSW240 |
||||
|
|
|
|||||
Model |
42/50/55LF65** |
|
|||||
|
|
|
|
|
|
|
|
VESA (A x B) |
|
|
400 x 400 |
|
|||
|
|
|
|
|
|
|
|
Standard screw |
|
|
|
M6 |
|
||
|
|
|
|
|
|
|
|
Number of screws |
4 |
|
|
||||
|
|
|
|
|
|
|
|
Wall mount bracket |
|
|
LSW440B |
|
|||
|
|
MSW240 |
|
||||
|
|
|
|
||||
|
|
|
|
|
|
||
|
|
|
|
A |
|
|
|
|
|
|
|
||||
|
|
B |
|
|
CAUTION
tDisconnect the power •rst, and then move or install the TV. Otherwise electric shock may occur.
tRemove the stand before installing the TV on a wall mount by performing the stand attachment in reverse.
t If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury. Use an authorised LG wall mount and contact the local dealer or quali•ed personnel.
t Do not over tighten the screws as this may cause damage to the TV and void your warranty.
tUse the screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.
NOTE
tUse the screws that are listed on the VESA standard screw speci•cations.
t The wall mount kit includes an installation manual and necessary parts.
t The wall mount bracket is not provided. You can obtain additional accessories from your local dealer.
t The length of screws may di!er depending on the wall mount. Make sure to use the proper length.
tFor more information, refer to the manual supplied with the wall mount.
<![endif]>ENGLISH
11
<![endif]>ENGLISH
tWhen installing the wall mounting bracket, use the Adhesive Label. The Adhesive Label will protect the opening from accumulating dust and dirt. (Only when the item of the following form is provided)
Provided Item
Adhesive Label
tWhen attaching a wall mounting bracket to the TV, insert the wall mount spacers into the TV wall mount holes to adjust the vertical angle of the TV. (Only when the item of the following form is provided)
Provided Item |
Wall Mount Spacer |
Connections (noti•cations)
Connect various external devices to the TV and switch input modes to select an external device. For more information of external device’s connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.
NOTE
t The external device connection may di!er from the model.
tConnect external devices to the TV regardless of the order of the TV port.
tIf you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. For more information of recording, refer to the manual provided with the connected device.
t Refer to the external equipment’s manual for operating instructions.
tIf you connect a gaming device to the TV, use the cable supplied with the gaming device.
tIn PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
tIn PC mode, some resolution settings may not work properly depending on the graphics card.
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
t Use a signal splitter to use more than 2 TVs.
tIf the image quality is poor, install a signal ampli#er properly to improve the image quality.
tIf the image quality is poor with an antenna connected, try to realign the antenna in the correct direction.
t An antenna cable and converter are not supplied.
tSupported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus, HE-AAC
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω).
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV mode.
tCheck if the CI module is inserted into the PCMCIA card slot in the right direction. If the module is not inserted properly, this can cause damage to the TV and the PCMCIA card slot.
tIf the TV does not display any video and audio when CI+ CAM is connected, please contact to the Terrestrial/Cable/Satellite Service Operator.
Euro scart connection
(Depending on model)
Transmits the video and audio signals from an external device to the TV set. Connect the external device and the TV set with the euro scart cable as shown.
12
Output |
|
Type |
AV1 |
Current |
(TV Out1) |
input mode |
|
Digital TV |
Digital TV |
|
|
Analogue TV, AV |
|
|
|
Component |
Analogue TV |
|
|
HDMI |
|
|
|
1TV Out : Outputs Analogue TV or Digital TV signals.
t Any Euro scart cable used must be signal shielded.
t When watching digital TV in 3D imaging mode, only 2D out signals
can be output through the SCART cable. (Only 3D models)
t If you use the Time Machine function on digital TV, monitor out signals cannot be output through the SCART cable. (Only 3D models)
Other connections
Connect your TV to external devices. For the best picture and audio quality, connect the external device and the TV with the HDMI cable. Some separate cable is not provided.
Remote control
(Depending on model)
The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching theand
ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse.
CAUTION
t Do not mix old and new batteries, as this may damage the remote control.
t The remote control will not be included for all sales market.
Make sure to point the remote control toward the remote control sensor on the TV.
INPUT |
|
|
|
A |
1 |
2 |
3 |
|
|
1.,;@ |
2abc |
3def |
|
|
4ghi |
5jkl |
|
6mno |
|
7pqrs |
8tuv |
|
9wxyz |
|
GUIDE |
0 |
|
Q.VIEW |
B |
|
FAV |
|
|
|
P |
4 |
A |
G |
|
|
E |
MUTE |
|
A
(POWER) Turns the TV on or o!.
1Changes the input source. (Depending on model)
1 Changes the input source. (Depending on model) 2
/
(Q. Settings) Accesses the Quick Settings.
(Depending on model)
2 Accesses the Quick Settings. (Depending on model)
3Resizes an image. (Depending on model)
3 Views the information of the current programme and screen. (Depending on model)
(User Guide) Sees user-guide.
B
Number buttons Enters numbers. Shows programme guide.
(Space) Opens an empty space on the screen keyboard.
Returns to the previously viewed programme.
Adjusts the volume level.
Accesses your favourite programme list.
4 Views the information of the current programme and screen. (Depending on model)
4 Used for viewing 3D video. (Depending on model)
Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen.
<![endif]>ENGLISH
13
<![endif]>ENGLISH
RECENT |
5 |
MY APPS |
|
|
|
C |
|
|
|
|
|
|
OK |
|
|
BACK |
LIVE MENU |
EXIT |
|
6 |
|
|
|
TEXT |
T.OPT |
APP/ |
|
LIVE TV |
|
|
|
REC/ |
D |
SUBTITLE AD TV/RAD
C
Shows the previous history.
5 (HOME) Accesses the Home menu. (Depending on model) 5
Accesses the Home menu. (Depending on model)
Shows the list of Apps.
Navigation buttons (up/down/left/right) Scrolls through menus or options.
Selects menus or options and con!rms your input.
Returns to the previous level.
Shows the list of Recommended, Programmes, Search and Recorded. (Depending on model)
Clears on-screen displays and returns to TV viewing.
D
6 Coloured buttons These access special functions in some menus.
(: Red,
: Green,
: Yellow,
: Blue)
TELETEXT buttons(, ) These buttons are used for teletext.
Returns to LIVE TV.
Selects the MHP TV menu source. (Only Italy) (Depending on model)
Control buttons () Controls the Premium contents, Time MachineReady or SmartShare menus or the SIMPLINK compatible devices (USB or SIMPLINK or Time MachineReady).
Starts to record and displays record menu. (Only Time MachineReady supported model) (Depending on model)
Recalls your preferred subtitle in digital mode.
By Pressing AD button, audio descriptions function will be enabled.
Selects Radio, TV and DTV programme.
Magic remote functions
(Depending on model)
When the message“Magic remote battery is low. Change the battery.”is displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching theand
ends to the label inside the compartment, and close the battery cover. Be sure to point the magic remote toward the remote control sensor on the TV. To remove the batteries, perform the installation actions in reverse.
CAUTION
tDo not mix old and new batteries, as this may damage the remote control.
A
1. @ |
2abc |
3def |
|
4ghi |
5jkl |
6mno |
|
7pqrs |
8tuv |
9wxyz |
|
LIST |
0 |
INFO |
|
|
|
EXIT |
B |
|
|
|
A
(POWER) Turns the TV on or o".
(INPUT) Changes the input source.
* Pressing and holding the button displays all the lists of external inputs.
Number buttons Enters numbers. Accesses the saved programme list.
(Space) Opens an empty space on the screen keyboard.
Views the information of the current programme and screen.
14
B
|
Adjusts the volume level. |
|
P |
Scrolls through the saved programmes. |
|
(MUTE) Mutes all sounds. |
|
|
* By pressing and holding the |
button, audio descriptions |
function will be enabled. (Depending on model) (HOME) Accesses the Home menu.
(BACK) Returns to the previous level.
Clears on-screen displays and return to TV viewing.
C
GUIDE
D
TEXT T.OPT SUBT.
C
Wheel (OK) Press the center of the Wheel button to select a menu. You can change programmes by using the wheel button.
Navigation buttons (up/down/left/right) Press the up, down, left or right button to scroll the menu.
If you press buttons while the pointer is in use, the pointer will disappear from the screen and Magic Remote will operate like a general remote control.
To display the pointer on the screen again, shake Magic Remote to the left and right.
Shows programme guide.
(Screen Remote) Displays the Screen Remote. *Accesses the Universal Control Menu. (Depending on model)
D
Used for viewing 3D video. (Only 3D models)
(Voice recognition)
(Depending on model)
Network connection is required to use the voice recognition function. 1. Press the voice recognition button.
2. Speak when the voice display window appears on the TV screen. t Use the Magic Remote no further than 10 cm from your face. t The voice recognition may fail when you speak too fast or too
slowly.
tThe recognition rate may vary depending on the user’s characteristics (voice, pronunciation, intonation, and speed) and the environment (noise and TV volume).
(Q. Settings) Accesses the Quick Settings.
* Pressing and holding thebutton displays the Advanced menu.
Coloured buttons These access special functions in some menus. (: Red,
: Green,
: Yellow,
: Blue)
TELETEXT buttons(,
) These buttons are used for teletext.
Recalls your preferred subtitle in digital mode.
Registering magic remote
How to register the magic remote
To use the Magic Remote, !rst pair it with your TV.
1 Put batteries into the Magic Remote and turn the TV on.
2 Point the Magic Remote at your TV and press theWheel (OK) on the remote control.
*If the TV fails to register the Magic Remote, try again after turning the TV o" and back on.
How to deregister the magic remote
Press the(BACK) and
(HOME) buttons at the same time, for !ve seconds, to unpair the Magic Remote with your TV.
* Pressing and holding thebutton will let you cancel and reregister Magic Remote at once.
<![endif]>ENGLISH
15
<![endif]>ENGLISH
How to use magic remote |
Open source software |
|
notice information |
tShake the Magic Remote slightly to the right and left or press (HOME),
(INPUT),
buttons to make the pointer appear
on the screen.
(In some TV models, the pointer will appear when you turn the
Wheel (OK) button.)
tIf the pointer has not been used for a certain period of time or Magic Remote is placed on a $at surface, then the pointer will disappear.
tIf the pointer is not responding smoothly, you can reset the pointer by moving it to the edge of the screen.
tThe Magic Remote depletes batteries faster than a normal remote due to the additional features.
Precautions to take when using the magic remote
t Use the remote control within the speci!ed range (within 10 m). You may experience communication failures when using the device outside the coverage area or if there are obstacles within the coverage area.
tYou may experience communication failures depending on the accessories.
Devices such as a microwave oven and wireless LAN operate in the
same frequency band (2.4 GHz) as the Magic Remote. This may cause communication failures.
tThe Magic Remote may not work properly if a wireless router (AP) is within 1 meter of the TV.
Your wireless router should be more than 1 m away from the TV. t Do not disassemble or heat the battery.
t Do not drop the battery. Avoid extreme shocks to the battery. t Inserting the battery in the wrong way may result in explosion.
Licenses
Supported licenses may di"er by model. For more information about licenses, visit www.lg.com.
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource. lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to
opensource@lge.com. This o"er is valid for three (3) years from the date on which you purchased the product.
Troubleshooting
Cannot control the TV with the remote control.
t Check the remote control sensor on the product and try again.
t Check if there is any obstacle between the product and the remote control.
tCheck if the batteries are still working and properly installed ( to
,
to
).
No image display and no sound is produced.
t Check if the product is turned on.
t Check if the power cord is connected to a wall outlet.
tCheck if there is a problem in the wall outlet by connecting other products.
The TV turns o" suddenly.
t Check the power control settings. The power supply may be interrupted.
t Check if the Automatic Standby(Depending on model) / Sleep Timer / Timer Power Off is activated in the TIMERS settings.
tIf there is no signal while the TV is on, the TV will turn o! automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI),‘No signal’or‘Invalid Format’is displayed.
t Turn the TV o!/on using the remote control. t Reconnect the HDMI cable.
t Restart the PC with the TV on.
16
Speci•cations
Wireless module specification
Because band channel used by the country could be different, the user can not change or adjust the operating frequency and this product is set for the regional frequency table.
This device should be installed and operated with minimum distance 20 cm between the device and your body. And this phrase is for the general statement for consideration of user environment.
0197
(Only LF63**, LF65**)
Wireless module (LGSBW41) Specification
|
Wireless LAN |
|
Bluetooth |
|
|
|
|
|
|
Standard |
IEEE802.11a/b/g/n |
Standard |
|
BluetoothVersion4.0 |
|
|
|
|
|
Frequency |
2400to2483.5MHz |
Frequency |
|
|
5150to5250MHz |
|
2400to2483.5MHz |
||
Range |
Range |
|
||
5725to5850MHz(forNonEU) |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
802.11a:13dBm |
|
|
|
Output |
802.11b:15dBm |
Output |
|
|
Power |
802.11g:14dBm |
Power |
|
10dBmorLower |
(Max.) |
802.11n-2.4GHz:16dBm |
(Max.) |
|
|
|
802.11n-5GHz:16dBm |
|
|
|
|
|
|
|
|
<![endif]>ENGLISH
17
Record the model number and serial number
of the TV. (Only DTV)
Refer to the label on the back cover and quote this information to your dealer when requiring any service.
MODEL
SERIAL