LG 32HL710S-W Owner’s Manual

OWNER’S MANUAL
IPS LED Monitor
(LED Monitor*)
* LG LED Monitor applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and retain it for future reference.
32HL710S
Copyright 2019 LG Electronics Inc. All Rights Reserved.
www.lg.com
CONTENTS
ON CLEANING .......................................3
ENGLISH
LICENSE ...............................................4
OPEN SOURCE SOFTWARE NOTICE
INFORMATION ......................................4
ASSEMBLY AND PREPARING ...................5
USER SETTINGS ..................................14
TROUBLESHOOTING ............................27
PRODUCT SPECIFICATIONS ...................29
EXTERNAL CONTROLLER SETUP .............35
Please note that this information is for proper use and safety of the equipment. The following symbols may indicate a hazardous situation in which, if not heeded, may result in serious injury or even death to the user or others, or damage to the equipment.

ON CLEANING

WARNING
• Indicates warning and safety instructions. If not adhered to, it could result in death or serious injury to the
user or others.
CAUTION
• Indicates a hazardous situation which, if not heeded, may result in minor or moderate injury to the user or
others, or damage to the equipment.
Recommended Cleaning Chemicals
ENGLISH
• Isopropanol 70 %
• Ethanol 70 %
• 0.9 % NaCl solution
How to Use Cleaner
• Prior to cleaning, turn off the monitor and remove the power cable.
• Soak a soft cloth in a recommended cleaner, then lightly rub the screen with no more than 1 N of force.
• The cleaner could cause serious damage if it leaks inside the monitor while cleaning.
• The display could be damaged, so only clean the parts of the monitor other than the screen's LCD panel.
• Do not use benzene, thinner, acids or alkaline cleaners or other such solvents.
• Cleaning guidelines for displays must only be carried out by medical professionals (Doctors or Nurses),
cleaners must not be handled by patients.

LICENSE

OPEN SOURCE SOFTWARE NOTICE
Each model has different licenses. Visit
ENGLISH
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
www.lg.com
for more information on the license.
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.
http://opensource.lge.com.
In addition to the source code, all referred license terms,
opensource@lge.com.
This offer is valid for

ASSEMBLY AND PREPARING

Product Composition
Please check whether all the components are included in the box before using the product. If there are any missing components, contact the retailer where you purchased the product.
Note that the product and related components may look different from those shown here.
CD (Owner's Manual / Software /
Regulatory Manual) / Cards
HDMI Cable
Power Cord AC/DC Adaptor
DisplayPort Cable
ENGLISH
CAUTION
• Always use genuine LG components to ensure safety and product performance.
• The product warranty will not cover damage or injury caused by the use of unauthorized components.
ENGLISH
• It is recommended to use the supplied components.
• If you use generic cables not certified by LG, the screen may not display or there may be image noises.
NOTE
• The components may look different from those illustrated here.
• Without prior notice, all product information and specifications contained in this manual are subject to
change to improve the performance of the product.
• To purchase optional accessories, visit an electronics store or an online shopping site, or contact the retailer
from which you purchased the product.
• The power cord provided may differ depending upon the region.
Supported Software
Check the drivers and software supported by your product and refer to the manuals on the CD enclosed in the product package.
Drivers and Software Installation Priority
True Color Pro Recommended
• Required and Recommended: You can download and install the latest version from the enclosed CD or from
the LGE website (
www.lg.com
).
Product and LED Control buttons
1 2 3 4 5 6 7 8
Front
ENGLISH
Bottom
9
LED Control button Functions
1
ENGLISH
• Selects the input mode.
2
• Adjusts display mode for 2 or more screens.
3
• Opens the [Hot key Settings] menu.
4
• Adjusts the screen brightness.
5
• Selects and confirms menus or options
6
• Adjusts the screen contrast.
7
• Displays LED Control buttons on the front panel and opens the menu mode.
8
Power indicator
• The green indicator illuminates if the power is on. The arrow indicates the position of the power switch.
9
Power switch
• Turns the power on/off.
NOTE
• The Power button is located at the bottom right on the front of the monitor.
• If the Control Key LED is turned off, press the Control Key button to turn the Control button LED on. When the Control Key LED is turned on, you can control the Control Key functions.
Connectors
Back
1 2 3 4 5 6 7
ENGLISH
9
8
ENGLISH
1
Potential Equalization Conductor
• Connect an equipotential plug.
2
• Connect the RS-232C terminal with an external device to control the monitor.
3
• Connect an AC/DC adapter.
• The output of the enclosed adaptor is 19 V.
• The product is designed to be used with adaptors that have an output ranging between 19-24 V.
4
• Receives or transmits digital video signals.
5
• Receives or transmits digital video signals.
6
• Input digital video signal.
• Using a DVI to HDMI / DisplayPort to HDMI cable may cause compatibility issues.
• Use a certified cable that displays the HDMI logo. The screen may not appear or a connection error
could occur if a non-certified cable is used.
• Recommended HDMI cable types
- High speed HDMI®/™ cable
- High speed HDMI®/™ Ethernet cable
7
• Receives or transmits digital video signals.
• There may be no video output depending on the DisplayPort version of your PC.
• A cable with DisplayPort 1.2 specifications is recommended when using a Mini DisplayPort to
DisplayPort cable.
8
• Used for HW Calibrator (Optional Accessory) connection.
• Connect peripheral device to the USB input port.
• A keyboard, mouse, or USB storage device can be connected.
• To use USB 2.0, connect the A-B type USB 2.0 cable to the PC.
CAUTION
Cautions When Using a USB Storage Device
• A USB storage device which has a built-in automatic recognition program or uses its own driver
might not be recognizable.
• Some USB storage devices may not be supported or may not work properly.
• It is recommended to use a USB hub or hard disk drive with power supplied. (If the power supplied
is not enough, the USB device may not be detected properly.)
9
- This USB port is used only for service.
NOTE
• All signal out terminals (SDI, DVI, etc.) output a signal when the power switch of the monitor is on. When the
power switch is off, no signal is outputted.
• This monitor supports the feature.
* : A feature that allows you to add a device to your computer without the need for physical
device configuration or user intervention.
• The standard of the DVI and the SDI output terminals for transmitting a screen
- : Connect a 5-meter cable to transmit a duplicated screen to a monitor.
- : Connect a 100-meter cable (BELDEN 1694) to transmit a duplicated screen to a monitor.
10
Installing the Monitor
Cable connection and organize
Before connecting the connectors, remove the back door as shown below.
1 2 3
4 5
CAUTION
• When the back door is attached to the monitor, the monitor meets water resistance standards. Do not use the monitor with the back door detached, as the water resistance capability is not guaranteed without the door.
ENGLISH
11
Installing on the Wall
Install the monitor at least 100 mm away from the wall on each side of the monitor to ensure sufficient ventilation. Detailed installation instructions can be obtained from your local dealer. Please refer to the manual to install and set up a tilting wall mounting bracket.
ENGLISH
100 mm
Installing the Wall Mount Plate
This monitor meets the specifications for the wall mount plate or other compatible devices.
Wall Mount (mm) Standard screw Required screws Wall mount plate (optional)
100 x 100
M4 x L10
LSW140
100 mm
100 mm
To install the monitor to a wall, attach a wall mount plate (optional) to the back of the monitor.
Make sure that the wall mount plate (optional) is securely fixed to the monitor and to the wall.
12
100 mm
NOTE
• A non-VESA standard screw may damage the product and cause the monitor to fall. LG Electronics is not
liable for any accidents relating to the use of non-standard screws.
• The wall mount kit includes the installation guide and all necessary parts.
• The wall mounting bracket is optional. You can obtain optional accessories from your local dealer.
• The length of the screw may differ for each wall mounting bracket. If you use screws longer than the standard
length, it may damage the inside of the product.
• For more information, please refer to the user manual for the wall mounting bracket.
• Be careful not to apply too much force while mounting the wall mount plate as it may cause damage to the
screen.
• Remove the stand before installing the monitor on a wall mount by performing the stand attachment in
reverse.
CAUTION
• Disconnect the power cord before moving or installing the monitor. There is risk of electric shock.
• Installing the monitor on the ceiling or on a slanted wall may result in the monitor falling off, which could
lead to injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel.
• Applying excessive force when tightening screws may damage the monitor. Such damage is not covered by
the product warranty.
• Use the wall mounting bracket and screws that confirm to VESA standards. Damage caused by the use or
misuse of inappropriate components is not covered by the product warranty.
• When measured from the back of the monitor, the length of each installed screw must be 8 mm or less.
Precautions for Connecting the Power Cord
ENGLISH
Wall mount plate
Wall mount plate
Back of the monitor
Screw specifications
: M4 x L10
Back of the monitor
Max. 8 mm
100-240 V ~
• Make sure to use the power cord that is provided in the product package. Connect the cord to a grounded
power outlet.
• If you need another power cord, please contact your local dealer or the nearest retail store.
13

USER SETTINGS

ENGLISH
Activating the Quick Menu
1 Press ( ) to activate the LED Control Button. When the LED Control button is activated, press ( ) to show the OSD Quick Menu. 2 Among the LED Control Button, press to move to the left or right or to move to the bottom or top or to set options. 3 In order to exit from the OSD Menu, press the LED Control Button ( ) or select [Exit].
The applicable setting options are as shown below.
Quick Menu Settings Explanation
[Exit]
[Input]
[Picture Mode] Selects the [Picture Mode].
[Gamma] Selects the screen's [Gamma].
[Color Temp] Selects the screen's [Color Temp].
[All Settings] Enters the All Settings menu.
CAUTION
• The Monitor OSD (On Screen Display) may differ from the description in the User Manual.
Closes the Quick Menu.
Selects the applicable input mode.
NOTE
• If the [Picture Mode] is not the [Custom] mode, [Gamma] and [Color Temp] will be deactivated.
14
Quick Settings
1 Press ( ) to activate the LED Control Button. When the LED Control Button is activated, press ( ) and select [All Settings] to show the complete OSD Menu. 2 Among the LED Control Button, press to move to the left or right or to move to the bottom or top to go to the [Quick Settings]. 3 Configure the options following the instructions that appear in the bottom right corner. 4 To configure an upper menu or another item, press the LED Control Button or press to move to the settings. 5 In order to exit from the OSD Menu, press the LED Control Button ( ) or press .
The applicable setting options are as shown below.
ENGLISH
[All Settings] > [Quick
Settings]
[Brightness]
Adjusts screen brightness.
Explanation
NOTE
• Press the button to toggle between [Turn on 'Brightness Stabilization']/[Turn off 'Brightness Stabilization'].
• When [Brightness Stabilization] is [On], the [Brightness] adjustment function is deactivated.
• When [Brightness Stabilization] is [On], [SMART ENERGY SAVING] and [DFC] functions are deactivated.
• When [Picture Mode] is set as [DICOM], or [Gamma] is set as [DICOM Gamma Curve] Setting, the [Brightness] adjustment function is deactivated.
[Contrast]
[Color Temp] Set your own color temperature. ([Custom], [6500K], [7500K], [9300K], [Manual])
[Hot key Settings] Designate a hotkey for screen image settings. After setting the hotkey, use the hotkey in the LED Control Button to enable the set menu. ([PIP Size], [Gamma], [Mono], [Color Temp], [Black
Adjusts the color contrast of the screen.
Stabilizer], [Screen Zoom], [Off])
[Hotkey 1] Select a function to use with [Hotkey 1].
[Hotkey 2] Select a function to use with [Hotkey 2].
15
Loading...
+ 32 hidden pages