Colour Television
OWNER’S MANUAL
Please read this manual carefully before operating your set. Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number |
: |
Serial number |
: |
Contents
Installation......................................................... |
2 |
Connection of external equipment.................. |
2 |
Location and function of controls................... |
3 |
Basic operation................................................. |
4 |
On screen menus.............................................. |
4 |
Setting up TV stations...................................... |
5 |
Picture adjustment............................................ |
6 |
Sound adjustment............................................. |
7 |
Time setting....................................................... |
8 |
Other functions................................................. |
8 |
USB mode.......................................................... |
9 |
PIP operation (option).................................... |
14 |
Teletext (option).............................................. |
14 |
Troubleshooting check list............................ |
15 |
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover.
Never apply DC power to the set. In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.
DISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The plug must remain readily operable
Warning
To prevent fire or shock hazard, do not expose the set to rain or moisture.
Do not place anything containing liquid on top of the set, this may cause a fire or could give an electric shock.
hazards. If the set does not operate properly, unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket on the back cover. For the best reception an outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
Service
Never remove the back cover of the set as this can expose you to very high voltage and other
Connection of external equipment
You can connect additional equipment, such as
VCRs, camcorders etc. to your set.What is shown here may be somewhat different from your set.
Aerial socket
1.Connect the RF out socket of the VCR to the aerial socket on the back of the set.
2.Connect the aerial cable to the RF aerial in socket of the VCR.
3.Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.
4.Select the programme number where the
VCR channel is stored.
5.Press the PLAY button on the VCR.
Audio/Video in/out sockets (option)
1.Connect the audio/video out sockets of the VCR to audio/video in sockets of the set and in sockets of the VCR to RF OUT sockets of the set.
2.If the VCR is connected to the AV sockets on the set, press the TV/AV button to select AV1,
AV2 or AV3.
3.Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
You can also record programmes received by the TV on video tape via audio/video out sockets.
Note : If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO socket of the set.
Euro scart socket (option)
1.Connect the Euro scart socket of the VCR to the Euro scart socket of the set.
2.Press the PLAY button on the VCR.
If your VCR outputs a switching voltage when connected to Euro scart socket, the set will switch to AV 1 mode automatically. But if you want to keep on watching TV mode, press the
D / E or NUMBER buttons.
Otherwise press the TV/AV button on the remote control handset to select AV 1 The VCR playback picture appears on the screen.
You can also record programmes received by the
TV on video tape.
Note : Signal type RGB, i.e. the signals red, green and blue can only be selected for the Euro scart socket. These signals are transmitted, for example, by a pay TV decoder, game machine or photo CD unit, etc.
Component in sockets (option)
1.Connect the COMPONENT video output sockets (Y Cb Cr, Y Pb Pr or Y B-Y R-Y) of the
COMPONENT (480i) to the COMPONENT INPUT sockets (Y PB PR) on the set.
2.Connect the audio cable from the COMPO-
NENT to AUDIO IN sockets of AV IN2.
3.Press the TV/AV button to select COMPONENT.
4.Press the PLAY button on the COMPONENT. The COMPONENT playback picture appears on the screen.
2
Location and function of controls
1 |
|
|
|
10 |
|
|
11 |
|
|
|
13 |
|
|
|
LIST |
|
|
|
14 |
|
1 |
2 |
3 |
2 |
4 |
5 |
6 |
|
7 |
8 |
9 |
3 |
|
0 |
|
4 |
|
OK |
|
|
|
|
|
6 |
|
|
|
5 |
|
|
12 |
|
|
|
|
7 |
|
|
|
9 |
|
|
|
(With TELETEXT / Without PIP) |
1 |
|
|
|
|
|
10 |
|
|
|
|
11 |
|
|
|
Q.VIEW |
LIST |
13 |
|
|
|
|
|
14 |
|
|
VOL- |
VOL+ |
ZOOM |
|
|
|
1 |
2 |
3 |
|
2 |
|
|
/ESC |
|
|
U |
4 |
5 |
6 |
|
|
S |
|
||||
B |
|
||||
|
|
7 |
8 |
9 |
|
3 |
|
|
SELECT |
|
8 |
|
|
0 |
|
||
|
|
|
PR |
|
|
4 |
|
VOL |
OK |
VOL |
|
|
|
|
|
|
|
|
|
|
PR |
|
|
|
|
|
|
|
12 |
6 |
|
USB |
|
|
9 |
7 |
|
|
|
|
|
|
|
|
|
|
(Without TELETEXT / PIP)
All the functions can be |
remote |
control handset. Some |
adjust- |
ed with the buttons on the front panel of the set.
Remote control handset
Before you use the remote control handset, please install the batteries. See the next page.
1.POWER
switches the set on from standby or off to standby.
2.NUMBER BUTTONS
Switches the set on from standby or directly select a number.
USB SELECT BUTTONS
Oprate USB function.
3.MENU
To display on-screen or exit from USB mode . Other local key is not available in USB mode.
4.D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby.
scans programmes automatically.
F / G (Volume Up/Down)
adjusts the volume. adjusts menu settings.
OK
accepts your selection or displays the current mode.
5.TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
6.SLEEP
sets the sleep timer.
7.USB BUTTON
Select the USB mode.
8.FAVOURITE
selects a favorite programme.
9.EYE/* (option)
switches the eye function on or off.
10.MUTE
switches the sound on or off.
11.TV/AV
selects TV or AV mode.
switches the set on from standby. exits the Teletext mode.
12.I/II/*
selects the language during dual language broadcast.selects the sound output (option).
13.Q.VIEW (or YELLOW)
returns to the previously viewed programme.
14.LIST (or BLUE)
displays the programme table.
COLOURED BUTTONS : These buttons are used for teletext (only TELETEXT models) or programme edit.
Battery installation
The remote control handset is powered by two AAA type batteries. To load the batteries, turn the remote control handset over and open the battery compartment. Install two batteries as indicated by the polarity symbols ( + and - ) marked inside the compartment.
Note : To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time.
3
Location and function of controls
MAIN POWER (ON/OFF) switches the set on or off.
POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby mode.dims when the set is switched on.
REMOTE CONTROL SENSOR
Note : Only use the supplied remote control handset. (When you use others, they will not be able to function.)
MENU
selects a menu.
OK
accepts your selection or displays the current mode.
F / G (Volume Down/Up) adjusts the volume. adjusts menu settings.
D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby.
AUDIO/VIDEO/USB IN SOCKETS (AV IN3)(option)
Connect the audio/video/USB out sockets of external equipment to these sockets.
Note :
Shown is a simplified representation of front or side panel. What is shown here may be somewhat different from your set or can not be supplied on your area.
Basic operation
On and off
1.Press the main power button to switch the set on.
2.If the set is in standby mode, press the POWER, D / E, TV/AV or NUMBER buttons on the remote control handset to switch it on fully.
3.Press the POWER button on the remote control handset.
The set reverts to standby mode.
4.Press the main power button again to switch the set off.
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains plug is replaced in the mains power socket.
Programme selection
You can select a programme number with the D / E or NUMBER buttons.
Volume adjustment
Press the F / G button to adjust the volume.
Q.VIEW (or YELLOW)
Press the Q.View (or YELLOW) button to view the last programme you were watching.
Mute function
Press the MUTE button. The sound is switched off and the display W appears.
You can cancel it by pressing the MUTE, F / G,
I/II/*(option), button.
On screen language selection
The menu can be displayed on the screen in desired language. First select your language.
1.Press the MENU button and then D / E button to select the Special menu.
2.Press the G button to select Language.
3.Press the G button and then D / E button to select your desired language.
All the on screen displays will appear in the selected language.
Press the OK or F button to select the Special menu.
4.Repeatedly press the MENU button to return to normal TV viewing.
On screen menus
The dialogue between you and your set takes place on screen with an operator menu. The buttons required for the operating steps are also displayed.
Menu selection
1.Press the MENU button and then D / E button to display each menu.
2.Press the G button and then D / E button to select a menu item.
3.Press the G button to display the sub menu or the pull-down menu.
4.Change the setting of an item in the sub or
pull-down menu with the F / G or D / E. You can move to the higher level menu with the OK or F button and to move to the lower
level menu press the G button.
Note :
a.In the teletext mode, menus are not displayed.
b.In some models, the Normal/Turbo search will not display, only the Start will display in the
Auto programme menu.
c.In some models, Tilt, Booster or Degauss
will not display.
d.On some models, the Language, X-WAVE will not display.
4
On screen menus
Station
|
AutoOprogramme |
{ |
|
|
ManualOprogramme |
{ |
|
|
ProgrammeOedit |
{ |
|
|
FavouriteOprogramme |
{ |
|
|
|
|
|
|
|
|
|
|
|
|
|
()O}{OOKOMENU
Station menu
Picture
|
|
PSM |
{ |
|
|
XD |
{ |
|
|
Contrast |
{ |
|
|
Brightness |
{ |
|
|
Colour |
{ |
|
|
Sharpness |
{ |
|
|
|
|
|
|
|
|
()O}{OOKOMENU
Picture menu
Sound
|
SSM |
{ |
|
TurbooSound |
{ |
|
AVL |
{ |
|
||
|
Balance |
{ |
|
X-WAVE |
{ |
|
|
|
|
|
|
|
|
|
()O}{OOKOMENU
Sound menu
Time
|
|
Clock |
{ |
|
|
Offotime |
{ |
|
|
Onotime |
{ |
|
|
Autoosleep |
{ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
()O}{OOKOMENU
|
|
|
|
Time menu |
|
|
Special |
||
|
|
|
||
|
|
Language |
{ |
|
|
|
Input |
{ |
|
|
|
Childolock |
{ |
|
|
|
Degauss |
{ |
|
|
|
|
|
|
|
|
|
|
|
()O}{OOKOMENU
|
Auto programme |
|
|
|
|
|
|
|
System |
{ |
BG |
|
|
|
BG |
|
StorageOfrom |
{ |
I |
|
|
|
I |
|
NormalOsearch |
{ |
DK |
|
or |
|
DK |
|
TurboOsearch |
{ |
L |
|
|
M |
|
|
|
|
|
|
|
|
|
|
()O}{OOKOMENU |
|
|
|
|
|
|
Manual programme |
|
|
|
|
|
|
|
Storage |
{ |
2 |
|
|
|
|
|
System |
{ |
|
|
|
|
|
|
Channel |
{ |
|
|
|
|
|
|
Fine |
{ |
|
|
|
|
|
|
Search |
{ |
|
|
|
|
|
|
Name |
{ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
()O}{OOKOMENU
Programme edit
0OO0OOARCO1D03OOO5OOSO69
OCO03OOO6OOSO17
OCO12OOO7OOSO22
OSO66OOO8OOCO09
OSO67OOO9OOCO11
OOOOCopy
MoveOOOOOOSkip
()}{OOKOMENU
Favourite programme
|
AutoOprogramme |
{ |
56nCaa0055 |
|
ManualOprogramme |
{ |
|
|
ProgrammeOedit |
{ |
|
|
FavouriteOprogramme |
{ |
|
|
|
|
|
|
|
|
|
|
|
|
|
}{O0_9O()OOKOMENU
Special menu
TV programme
Setting up TV stations
Auto programme tuning
All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set.
System :
BG :(Asia/NewZealand/ M.East/Africa/Australia)
I:(Hong Kong/South Africa)
DK :(East Europe/China/Africa/CIS)
L :(SECAM L/L’ (France) (option)
M : (USA/Korea/Philippines) (option)
Note :
a.Turbo search is faster than Normal search and in some models, these searches will automatically store all receivable stations.
b.If the programmed station has poor quality and sound, select the system again in the
Manual programme menu.
Manual programme tuning
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station name with five characters to each programme number.
Booster (option)
If the reception is poor at the fringe area of the TV signal, select Booster to On.
Fine tuning
Normally fine tuning is only necessary if reception is poor.The finely tuned programme will be indi cated by yellow number during programme selection.
5