LG 26LH200C, 32LH210C, SAC34026003, 37LH200C, 26LH210C User Manual

...
Please read this manual carefully before operating your set and retain it for future reference.
The model and serial number of the TV is located on the back and one side of the TV.
Record it below should you ever need service.
Model:
Serial:
LCD TV OWNER’S MANUAL
26LH210C 32LH210C
26LH200C 32LH200C 37LH200C 42LH200C
42LH300C 47LH300C
P/NO : SAC34026003 (0907-REV00)
www.lgcommercial.com
This product qualifies for ENERGY STAR in the “factory default (Home Use)” setting.
Changing the factory default settings or enabling other features may increase power consumption that could exceed the limits necessary to quality for ENERGY STAR.
1-800-243-0000 USA, Consumer User 1-888-865-3026 USA, Commercial User 1-888-542-2623 CANADA
LG Customer Information Center
2

WARNING / CAUTION

The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera­ture accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
WARNING / CAUTION
To prevent fire or shock hazards, do not expose this product to rain or moisture.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause unde­sired operation (of the device).
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.
3

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus com­bination to avoid injury from tip-over.
Unplug this apparatus during lighting storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power­supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
1
2
3
4
5
7
8
6
9
10
4
SAFETY INSTRUCTIONS
Never touch this apparatus or antenna during a thunder or lighting storm.
When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.
Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something.
CAUTION concerning the Power Cord: It is recommend that appliances be placed
upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.
Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
GGRROOUUNN DD IINN GG
Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC out­let). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS
Mains plug is the disconnecting device. The plug must remain readily operable.
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH.
12
11
14
13
16
17
18
19
Powe r Supply
Short-circuit
Breaker
15
5
AANN TT EENN NNAASS OOuuttddoooo rr aanntteennnnaa ggrroouunnddiinn gg
If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of over­head power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna dis­charge unit, connection to grounding elec­trodes and requirements for the grounding electrode.
AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700
CC lleeaanniinngg
When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
MMoovvii nngg
Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV.
VVeennttiillaattiioo nn
Install your TV where there is proper ventila­tion. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places.
If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center.
Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it.
Keep the product away from direct sunlight.
FFoorr LLCCDD TTVV
If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV.
Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.
Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary dis­tortion effects on the screen.
20
23
24
25
26
27
21
22
Antenna Lead in Wire
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductor (NEC Section 810-21)
Ground Clamps
Power Service Grounding Electrode System (NEC Art 250, Part H)
Ground Clamp
Electric Service
Equipment
NEC: National Electrical Code
ON DISPOSAL
(Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.
6

CONTENTS

WARNING / CAUTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY INSTRUCTIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . 3
FEATURE OF THIS TV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PREPARATION
Accessories
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel Information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Stand Instruction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cable Management
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
Desktop Pedestal Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Swivel Stand
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
Kensington Security System
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Attaching the TV to a Desk
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Securing the TV to the wall to prevent falling when the TV is used on a stand
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
Antenna or Cable Connection
. . . . . . . . . . . . . . . . . . . . . . . . . . 19
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23
VCR Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
USB Connection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Audio out Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PC Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
WATCHING TV / CHANNEL CONTROL
Remote Control Functions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
Turning On TV
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
Channel Selection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
Volume Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
Initial Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
On-Screen Menus Selection
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
Quick Menu
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Channel Setup
- Auto Scan (Auto Tuning)
. . . . . . . . . . . . . . . . . . . . . . . . . . . 42
- Add / Delete Channel (Manual Tuning) . . . . . . 43
- Channel Editing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
Channel List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Favorite Channel Setup / Favorite Channel List
. . 46
Brief Information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Input List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
AV Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
SIMPLINK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
USB
Entry Modes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Photo List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Music List
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
59
PICTURE CONTROL
Picture Size (Aspect Ratio) Control
. . . . . . . . . . . . . . . . . . 62
Picture Wizard
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Preset Picture Settings (Picture Mode)
. . . . . . . . . . . . . 66
Manual Picture Adjustment - User Mode
. . . . . . . . . . 67
Picture Improvement Technology
. . . . . . . . . . . . . . . . . . . . .
68
Expert Picture Control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Energy Saving
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Picture Reset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Power Indicator
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
Demo Mode
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
7
SOUND & LANGUAGE CONTROL
Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 76
Clear Voice II
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Preset Sound Setting (Sound Mode)
. . . . . . . . . . . . . . . . 78
Sound Setting Adjustment - User Mode
. . . . . . . . . . . 79
Balance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
Audio Reset
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81
TV Speakers On/Off Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
External Speakers On/Off Setup
. . . . . . . . . . . . . . . . . . . . . 83
Stereo/SAP Broadcasts Setup
. . . . . . . . . . . . . . . . . . . . . . . . . .
84
Audio Language
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
On-Screen Menus Language Selection
. . . . . . . . . . . . . 86
Caption Mode
- Analog Broadcasting System Captions
. . . . . . . 87
- Digital Broadcasting System Captions
. . . . . . . . 88
- Caption Option
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
89
TIME SETTING
Clock Setting
- Auto Clock Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
- Manual Clock Setup
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91
Auto On/Off Time Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Sleep Timer Setting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
PARENTAL CONTROL / RATINGS
Set Password & Lock System
. . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Channel Blocking
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Movie & TV Rating
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1
External Input Blocking
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 2
Key Lock
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 3
APPENDIX
Troubleshooting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4
Maintenance
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 6
Product Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
IR Codes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 8
External Control Through RS-232C
. . . . . . . . . . . . . . . . .110
Open Source License
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
8
FEATURE OF THIS TV
AV Mode is three preset picture and audio settings. It allows the viewer to quickly switch between common settings. It includes Cinema, Sports, and Game Modes.
Automatically enhances and amplifies the sound of human voice frequency range to help keep dialogue audible when background noise swells.
Matches the original frame rate of the film for a more film-like experience
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."
is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.
Manufactured under license from Dolby Laboratories. “
Dolby
“and the double-D symbol are trademarks of
Dolby Laboratories.
This TV contains the detailed calibrations necessary for professional certification by the Imaging Science Foundation. The resulting ISF “day” and “night” modes will then be accessible by the user to experience the best their LG HDTV has to offer. CALIBRATE LIKE A PRO: Sophisticated and detailed calibrations can be made through the ISFccc mode. Detailed calibration requires a licensed technician. Please contact your local dealer to inquire about an ISF certified technician.
High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV
for an extended period, it can become permanently imprinted on the screen. This phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period
(2 or more hours for LCD, 1 or more hours for Plasma).
Image burn can also occur on the letterboxed
areas of your TV if you use the 4:3 aspect ratio setting for an extended period.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN / BURN-IN” ON YOUR TV SCREEN

PREPARATION

9

ACCESSORIES

PREPARATION
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV.
The accessories included may differ from the images below.
1.5V 1.5V
1.5V 1.5V
Owner’s Manual Power Cord
Installer Remote Control,
Batteries
L
I S T
3
56
78
0
9
FLASHBK
M
U
T E
V
O
L
CH
P
A
G
E
T U
R N
ENTER
FAV
M A
R K
Q
. M E
N U
M E
N
U
L
I S T
123
456
78
0
9
FLASHBK
M U
T E
V
O
L
C H
P A G
E
R
E T
U R
N
I N F
O
ENTER
I N
P U
T
P
O
W
E R
A V
M
O D
E
E N E
R G
Y S
A V I
N G
User Remote Control,
Batteries
P
O
W
E R
M
U T
E
S A
P
123
456
789
0
I N
F O
C C
I N
P U
T
T I M
E R
B E
D 1
B
E D
2
R
E
T U
R N
F L
A S H
B
K
CH
C
H
VOL
O
K
VO
L
CD Manual
Screws for stand assembly
(Refer to P.12)
Screw for stand fixing
(Refer to P.17)
Protection Cover
(Refer to P.13)
x 4
OOppttiioonn EExxttrraass
* Wipe spots on the exterior only with
the polishing cloth.
* Do not wipe roughly when removing
stain. Excessive pressure may cause scratch or discoloration.
Polishing Cloth
Not included with all models
D-sub 15 pin Cable
When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.
(Except 47LH300C)
(For 26LH210C, 32LH210C)
Protective Bracket and Bolt
for Power Cord
(Refer to P.15)
PREPARATION
10

FRONT PANEL INFORMATION

PREPARATION
Image shown may differ from your TV.
CHANNEL (
EE,DD
) Buttons
VOLUME (-, +) Buttons
ENTER Button
26LH200C, 26LH210C
MENU Button
POWER Button
INPUT Button
SPEAKER
Remote Control Sensor, Power/Standby Indicator
Illuminates red in standby mode. Illuminates blue when the TV is switched on. (Can be adjusted using the
PPoo wweerr IInnddii cc aattoorr
in the OPTION menu.
GG
pp..77 44
)
32LH210C, 32/37/42LH200C, 42/47LH300C
INPUT
MENU
ENTER
CH
VOL
CHANNEL (DD,EE) Buttons
VOLUME (+, -) Buttons
ENTER Button
MENU Button
INPUT Button
POWER Button
INPUT MENU
ENTER
VOL
CH
PREPARATION
11

BACK PANEL INFORMATION

Image shown may differ from your TV.
AV IN 2
L/ MONO
R
AUDIO
VIDEO
USB IN
2
11
AUDIO IN
(RGB/DVI)
ANTENNA/
CABLE IN
VIDEO
AUDIO
RGB IN (PC)
RJP
REMOTE
CONTROL IN
VIDEO AUDIO
L(MONO)
R
L
SPEAKER OUT
R
L R
OPTICAL DIGITAL
AUDIO OUT
COMPONENT IN
AV IN 1
2
1
/DVI IN
R
RS-232C IN
(
CONTROL&SERVICE)
2
1
3
4
5
78 6910
12
1
2
3
4
5
9
8
7
6
10
11
12
RJP (REMOTE JACK PACK) PORT
Connect to remote jack pack control output port.
AV (Audio/Video) IN
Analog composite connection. Supports standard definition video only (480i).
HDMI/DVI IN, HDMI IN
Digital Connection. Supports HD video and Digital audio. Doesn’t
support 480i. Accepts DVI video using an adapter or HDMI to
DVI cable (not included).
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable).
AUDIO IN (RGB/DVI)
1/8" (0.32 cm) headphone jack for analog PC audio input.
OPTICAL DIGITAL AUDIO OUT
Digital optical audio output for use with amps and home theater systems.
Note: In standby mode, this port doesn’t work.
ANTENNA/CABLE IN
Connect over-the air or cable signals to this jack.
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices.
This port is used for Service or Hotel mode.
REMOTE CONTROL IN PORT
For a wired remote control.
SPEAKER OUT PORT
Used for external speaker jack.
COMPONENT IN
Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red
and white for audio.
USB IN
Used for viewing photos and listening to MP3s.
Power Cord Socket
For operation with AC power. Caution: Never attempt to operate the TV on DC
power.
PREPARATION
12

STAND INSTRUCTIONS

PREPARATION
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the TV as shown.
Fix the 4 screws securely using the holes in the back of the TV.
1
2
3
INSTALLATION
GG
When assembling the desk type stand, make sure the screws are fully tightened (If not tightened fully, the TV can tilt forward after the product installation). Do not over tighten.
NOTE
!
Image shown may differ from your TV.
PREPARATION
13
DETACHMENT
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
1
Remove the screws from the TV.
2
Detach the stand from TV.
3
After removing the stand, install the included pp rroo tteecc ttiioonn ccoo vv eerr
over the hole for the stand.
Press the
PPRROOTTEECCTTIIOONN CCOOVVEERR
into the TV
until you hear it click.
PROTECTION COVER
PREPARATION
14

VESA WALL MOUNTING

PREPARATION
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer.
GG
Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock.
CAUTION
GG
Screw length needed depends on the wall mount used. For further information, refer to the instruc­tions included with the mount.
GG
Standard dimensions for wall mount kits are shown in the table.
GG
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
GG
Do not use screws longer then the standard dimen­sion, as they may cause damage to the inside to the TV.
GG
For wall mounts that do not comply with the VESA
standard screw specifications, the length of the screws may differ depending on their specifica­tions.
GG
Do not use screws that do not comply with the VESA standard screw specifications.
Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents.
GG
LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installa­tion instructions.
NOTE
!
Model
VESA (A *B)
Standard Screw Quantity
Wall Mounting Bracket
(sold separately)
37LH200C, 42LH200C, 42LH300C,
47LH300C
26LH200C
26LH210C
32LH210C, 32LH200C
200* 10 0 M 4 4
200* 200 M6 4
AA
BB
RW230 AW-47LG30M
AW-47LG30M
RW230
PREPARATION
15

CABLE MANAGEMENT

Image shown may differ from your TV.
Connect the cables as necessary. To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Secure the power cable with the PROTECTIVE BRACKET and SCREW as shown. It will help prevent the power cable from being removed by accident.
Install the CABLE MANAGEMENT CLIP as shown.
CABLE MANAGEMENT CLIP
PROTECTIVE BRACKET
1
2
Put the cables inside the CABLE MANAGEMENT CLIP and snap it closed.
3
GG
Do not hold the CABLE MANAGEMENT CLIP when moving the TV.
- If the TV is dropped, you may be injured or the product may be broken.
NOTE
!
PREPARATION
16

DESKTOP PEDESTAL INSTALLATION

PREPARATION

SWIVEL STAND

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
Image shown may differ from your TV.
4 inches
GG
Ensure adequate ventilation by following the clearance recommendations.
GG
Do not mount near or above any type of heat source.
CAUTION
4 inches
4 inches
4 inches

KENSINGTON SECURITY SYSTEM

This feature is not available for all models.
- The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below.
- For the detailed installation and use of the Kensington Security
System, refer to the user’s guide provided with the Kensington Security System.
For further information, contact
hhttttpp:: ////ww wwww ..kkeenn ssiinnggttoonn..cc oomm
, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as note­book PCs and LCD projectors.
NOTE: The Kensington Security System is an optional accessory.
PREPARATION
17

ATTACHING THE TV TO A DESK

Image shown may differ from your TV.
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
GG
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
WARNING
1-Screw
(provided as parts of the product)
Desk
Stand
(Except 47LH300C)
GG
Screw: M5 x L
(*L: Table depth + 8~10 mm)
ex) Table depth: 15mm, Screw: M5 x 25
4-Screws (not provided as parts of the product)
Stand
Desk
PREPARATION
18

SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND

PREPARATION
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
Use a sturdy rope (sold separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).
Image shown may differ from your TV.
GG
Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
GG
To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.
NOTE
!
PREPARATION
19

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.
For optimum picture quality, adjust antenna direction if needed.
2. Cable
Wa ll Antenna Socket
Outdoor Antenna (VHF, UHF)
Cable TV Wall Jack
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
RF Coaxial Wire (75 ohm)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Be careful not to bend the copper wire when connecting the antenna.
Copper Wire
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
If the antenna is not installed properly, contact your dealer for assistance.
Refer to
hhttttpp::// //AAnntteennnnaa WWeebb..oorrgg
for more information about antennas and Digital TV.
ANTENNA/
CABLE IN
To prevent damage do not connect to the power outlet until all connections are made between the devices.
Image shown may differ from your TV.
ANTENNA/
CABLE IN

EXTERNAL EQUIPMENT SETUP

20
EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device.

Component Connection

1. How to connect
Connect the video outputs (Y, P
B
, PR
)
of the digital set-
top box to the
CC OO MMPP OO NNEENNTT IINN VV IIDDEEOO
jacks on
the TV. Match the jack colors (Y = green, P
B
= blue, and
P
R = red).
Connect the audio output of the digital set-top box to the
CC OO MMPP OO NNEENNTT II NN AAUUDDIIOO
jacks on the TV.
2
1
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box operation.
)
Select the
CC oommppoo nneenntt
input source on the TV using the
IINN PPUUTT
button on the remote control.
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
RJP
REMO
CONTRO
VIDEO AUDIO
L(MONO)
R
L
SPEAKER OUT
R
AV IN 1
2
1
/DVI IN
VIDEO
AUDIO
L R
COMPONENT IN
Y L RPB PR
1
2
Y, C
B/
PB
, C
R/P
R
Supported Resolutions
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
15.73 59.94
15.73 60.00
31.47 59.94
31.50 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
26.97 23.976
27.00 24.00
33.71 29.97
33.75 30.00
67.432 59.94
67.50 60.00
Resolution
720x480i
720x480p
1280x720p
1920x1080i
1920x1080p
Signal
480i
480p
720p
10 8 0 i
10 8 0 p
Component
Yes
Yes
Yes
Yes
Yes
HDMI
No
Yes
Yes
Yes
Yes
EXTERNAL EQUIPMENT SETUP
21

HDMI Connection

Connect the digital set-top box to the
HHDDMMII//DDVVII
IINN 11
or
HHDDMMII 22
jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box.
)
Select the
HHDDMMII11orHHDDMMII22
input source on the TV using
the
IINNPPUUTT
button on the remote control.
2
1
AUDIO IN
(RGB/DVI)
AUDIO
RGB IN (PC)
REMOTE
CONTROL IN
VIDEO AUDIO
L(MONO)
R
L
SPEAKER OUT
R
L R
AV IN 1
O
2
1
/DVI IN
HDMI OUTPUT
RS-232C IN
(
CONTROL&SERVICE)
1
HDMI-DTV
Horizontal Vertical
Frequency(KHz)Frequency(Hz
)
31.47 59.94
31.50 60.00
44.96 59.94
45.00 60.00
33.72 59.94
33.75 60.00
26.97 23.976
27.00 24.00
33.71 29.97
33.75 30.00
67.432 59.94
67.50 60.00
Resolution
720x480p
1280x720p
1920x1080i
1920x1080p
GG
Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.
NOTE
!
EXTERNAL EQUIPMENT SETUP
22
EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

AUDIO IN
(RGB/DVI)
ANTENNA
CABLE IN
AUDIO
RGB IN (PC)
REMOTE
CONTROL IN
O AUDIO
L(MONO)
R
L
SPEAKER OUT
R
L R
AV IN 1
OPTICAL DIGIT
AUDIO OUT
2
1
/DVI IN
L R
DVI OUTPUT
AUDIO
RS-232C IN
(
CONTROL&SERVICE)
1
2
GG
A DVI to HDMI cable or adapter is required for this con­nection. DVI doesn't support audio, so a separate audio connection is necessary.
NOTE
!
Connect the DVI output of the digital set-top box to the
HHDDMMII//DDVVII IINN 11
or
HHDDMMII 22
jack on the TV.
Connect the digital set-top box audio output to the AAUUDDII OO IINN ((RRGGBB//DDVVII ))
jack on the TV.
1. How to connect
2. How to use
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box.
)
Select the
HHDDMMII11 orHHDDMMII22
input source on the TV using
the
IINNPPUUTT
button on the remote control.
2
1
EXTERNAL EQUIPMENT SETUP
23

DVD SETUP

Component Connection

Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
YPB PR
Video output ports
on DVD player
Y
Y
Y
Y
P
B
B-Y
Cb
Pb
P
R
R-Y
Cr
Pr
T
1 2
Connect the video outputs (Y, PB
, P
R
)
of the DVD to
the
CCOOMMPPOONNEENNTT IINN VVII DDEEOO
jacks on the TV. Match
the jack colors (Y = green, P
B
= blue, and PR = red
)
.
Connect the audio outputs of the DVD to the CC OO MM PPOO NNEENNTT II NN AAUUDDIIOO
jacks on the TV.
1. How to connect
2. How to use
Turn on the DVD player, insert a DVD.
Select the
CC oommppoo nneenntt
input source on the TV using the
IINN PPUUTT
button on the remote control.
Refer to the DVD player's manual for operating instructions.
2
1
Y L RPB PR
RJP
VIDEO
COMPONENT IN
AV IN 1
VIDEO AUDIO
L(MONO)
L R
AUDIO
L
SPEAKER OUT
2
R
1
/DVI IN
R
REMO
CONTRO
EXTERNAL EQUIPMENT SETUP
24
EXTERNAL EQUIPMENT SETUP

Composite (RCA) Connection

VIDEO
AUDIO
RJP
REMOTE
CONTROL
L
SPEAKER OUT
R
L R
COMPONENT IN
2
1
/DVI IN
AV IN 1
VIDEO AUDIO
L(MONO)
R
L R
VIDEO
AUDIO

HDMI Connection

AUDIO IN
(RGB/DVI)
ANT
CAB
AUDIO
RGB IN (PC)
REMOTE
CONTROL IN
L(MONO)
R
L
SPEAKER OUT
R
L R
IN
AV IN 1
OPTICAL
AUDIO
2
1
/DVI IN
HDMI OUTPUT
RS-232C IN
(
CONTROL&SERVICE)
1
Connect the
AAUUDDIIOO/VVIIDD EEOO
jacks between TV and DVD. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).
1. How to connect
2. How to use
Turn on the DVD player, insert a DVD.
Select the
AAVV11
or
AAVV11
input source on the TV using the
IINN PPUUTT
button on the remote control.
Refer to the DVD player's manual for operating instructions.
1
Connect the HDMI output of the DVD to the HHDDMMII//DDVVII IINN 11
or
HHDDMMII 22
jack on the TV.
No separated audio connection is necessary. HDMI supports both audio and video.
1. How to connect
2. How to use
Select the
HHDDMMII11 orHHDDMMII22
input source on the TV using
the
IINN PPUUTT
button on the remote control.
Refer to the DVD player's manual for operating instructions.
2
1
GG
Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.
NOTE
!
1
EXTERNAL EQUIPMENT SETUP
25

VCR SETUP

Antenna Connection

Connect the RF antenna out socket of the VCR to the
AANN TT EENN NNAA//CCAABBLLEE II NN
sock-
et on the TV.
Connect the antenna cable to the RF antenna in socket of the VCR.
1. How to connect
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.
)
2. How to use
2
1
DIO IN
RGB IN (PC)
OPTICAL DIGITAL
AUDIO OUT
ANTENNA/
CABLE IN
L R
S-VIDEO VIDEO
OUTPUT
SWITCH
ANT IN
ANT OUT
AUDIO
RS-232C IN
Wall Jack
Antenna
1
2
PREPARATION
26
PREPARATION

Composite (RCA) Connection

GG
If you have a mono VCR, connect the audio cable from the VCR to the
AAUUDDII OO LL//MM OO NNOO
jack of the TV.
NOTE
!
VIDEO
AUDIO
RJP
REMO
CONTR
L
SPEAKER OUT
R
L R
COMPONENT IN
2
1
/DVI IN
AV IN 1
VIDEO AUDIO
L(MONO)
R
L R
S-VIDEO VIDEO
AUDIO
OUTPUT SWITCH
ANT IN
ANT OUT
1
Connect the
AAUUDDIIOO/VVIIDD EEOO
jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).
1. How to connect
2. How to use
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.
)
Select the
AAVV11
or
AAVV22
input source on the TV using the
IINN PPUUTT
button on the remote control.
1
PREPARATION
27

OTHER A/V SOURCE SETUP

AV IN 2
L/ MONO
R
AUDIO
VIDEO
USB IN
L R
VIDEO
Camcorder
Video Game Set
Connect the
AAUUDDIIOO/VVIIDDEEOO
jacks between TV and external equipment. Match the jack colors
.
(
Video = yellow, Audio Left = white, and
Audio Right = red
)
1. How to connect
2. How to use
Select the
AAVV11
or
AAVV22
input source on the TV
using the
IINN PPUUTT
button on the remote control.
Operate the corresponding external equipment.
1
1
EXTERNAL EQUIPMENT SETUP
28

USB CONNECTION

EXTERNAL EQUIPMENT SETUP
USB IN
AV IN 2
L/ MONO
R
AUDIO
VIDEO
Memory Key
Connect the USB device to the
UUSSBB II NN
jack on the side
of TV.
1. How to connect
1
2. How to use
After connecting the
UUSSBB II NN
jack, you use the USB func-
tion. (
GG
pp..5544
)
1
or
EXTERNAL EQUIPMENT SETUP
29

AUDIO OUT CONNECTION

Send the TV’s audio to external audio equipment via the Audio Output port.
If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
AUDIO IN
(RGB/DVI)
ANTENNA/
CABLE IN
RGB IN (PC)
REMOTE
CONTROL IN
R
R
R
2
1
/DVI IN
OPTICAL DIGITAL
AUDIO OUT
RS-232C IN
(
CONTROL&SERVICE)
1
2
AU
(RG
VIDEO
AUDIO
RJP
REMOTE
CONTROL IN
VIDEO AUDIO
L(MONO)
R
L R
COMPONENT IN
AV IN 1
2
1
/DVI IN
L
SPEAKER OUT
R
L R
AUDIO
(
C
1
GG
When connecting with external audio equipments, such as amplifiers or speakers, you can turn the TV speakers off in the menu. (
GG
pp.. 88 22
)
NOTE
!
G
Do not look into the optical output port. Looking at the laser beam may damage your vision.
GG
Audio with ACP (Audio Copy Protection) function may block digital audio output.
CAUTION
Connect one end of the optical cable to the TV port of
OOPPTTIICCAALL DDIIGGIITTAALL AAUUDDIIOO OOUUTT
.
Connect the other end of the optical cable to the digital audio input on the audio equipment.
Set the “TV Speaker option - Off” in the AUDIO menu. (
GG
pp..8822
). See the external audio equipment instruction
manual for operation.
1. How to connect
2
3
1
Connect audio outputs to the TV’s
SSPPEEAAKKEERR OOUUTT
jacks.
Set the “External Speaker option - On” in the AUDIO menu. (
GG
pp..8833
). See the external audio equipment instruc-
tion manual for operation.
1. How to connect
2
1
Analog
Digital
EXTERNAL EQUIPMENT SETUP
30

PC SETUP

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

AUDIO IN
(RGB/DVI)
A C
AUDIO
RGB IN (PC)
REMOTE
CONTROL IN
VIDEO AUDIO
L(MONO)
R
L
SPEAKER OUT
R
L R
AV IN 1
OPTI
AU
2
1
/DVI IN
AUDIO
DVI OUTPUT
RS-232C IN
(
CONTROL&SERVICE)
1
2
Connect the DVI output of the PC to the
HHDDMMII//DDVVII
IINN 11
or
HHDDMMII 22
jack on the TV.
Connect the PC audio output to the
AAUUDDII OO IINN
((RR GG BB // DDVVII))
jack on the TV.
1. How to connect
2. How to use
Turn on the PC and the TV.
Select the
HHDDMMII11 orHHDDMMII22
input source on the TV using
the
IINN PPUUTT
button on the remote control.
2
1
GG
Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat­est cables that support HDMI version 1.3.
NOTE
!
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

VGA (D-Sub 15 pin) Connection

AUDIO IN
(RGB/DVI)
ANTENNA/
CABLE IN
RGB IN (PC)
REMOTE
CONTROL IN
2
1
/DVI IN
OPTICAL DIGITAL
AUDIO OUT
RGB OUTPUT
AUDIO
RS-232C IN
(
CONTROL&SERVICE)
2
1
Connect the VGA output of the PC to the
RRGGBB IINN
((
PP CC
))
jack on the TV.
Connect the PC audio output to the
AAUUDDIIOO II NN
((
RRGGBB// DDVVII
))
jack on the TV.
1. How to connect
2. How to use
Turn on the PC and the TV.
Select the
RRGGBB--PP CC
input source on the TV using the
IINN PP UU TT
button on the remote control.
2
1
Loading...
+ 100 hidden pages