Lexmark MX810DTFE, MX711DHE, MX710DE3, MX810DE, MX710DHE User Manual
...
Model name
MX710 series –
Lexmark MX710de (Lexmark XM5163), Lexmark MX710de3, Lexmark MX710dhe, Lexmark MX711de
(Lexmark XM5170), Lexmark MX711de3, Lexmark MX711dhe, Lexmark MX711dthe
MX810 series –
Lexmark MX810de (Lexmark XM7155), Lexmark MX810dte (Lexmark XM7155x), Lexmark MX810dfe,
Lexmark MX810dme, Lexmark MX810dxe, Lexmark MX810dpe, Lexmark MX810dtme, Lexmark MX810dtfe,
Lexmark MX810dxme, Lexmark MX810dxfe, Lexmark MX810dxpe, Lexmark MX810dtpe
Lexmark MX811de (Lexmark XM7163), Lexmark MX811dte (Lexmark XM7163x), Lexmark MX811dfe,
Lexmark MX811dme, Lexmark MX811dxe, Lexmark MX811dpe, Lexmark MX811dtme, Lexmark MX811dtfe,
Lexmark MX811dxme, Lexmark MX811dxfe, Lexmark MX811dxpe, Lexmark MX811dtpe
Lexmark MX812de (Lexmark XM7170), Lexmark MX812dpe, Lexmark MX812dte (Lexmark XM7170x),
Lexmark MX812dfe, Lexmark MX812dme, Lexmark MX812dxe, Lexmark MX812dtme, Lexmark MX812dtfe,
Lexmark MX812dxme, Lexmark MX812dxfe, Lexmark MX812dxpe, Lexmark MX812dtpe
Items
Quantity
Notes
Polychlorinated biphenyls (PCB) containing capacitors
0
N/A
Disassembly of Waste Electrical and Electronic Equipment (WEEE) Manual
EU Waste Electronic and Electrical Equipment Directive require producers to provide information of the different electronic
and electrical materials and components found in their products at its end-of-life, and disassembly references to treatment
and recycling facilities.
The disassembly information for this product has been prepared for use by a recognized treatment or recycling facility and
is not intended to be used by others.
1. Product information
2. Materials and components list for selective treatment
3. Disassembly tools
4. Disassembly references
The following information is intended only for the use of treatment and recycling facilities.
All disassembly instructions should be performed with the power switch in the OFF position. Disconnect the power cord
from the wall outlet and from the printer before continuing. If there are any other devices attached to the printer, then turn
them off as well, and unplug any cables going into the printer.
1. Product information
Model name(s)—Indicate all model name(s) within the product family.
* Add rows as needed
2. Materials and components list for selective treatment
Doc No.: Rev. 001 Page 1 of 18
Mercury containing components, such as switches or
backlighting lamps
0
N/A
Batteries
1
Lithium Manganese Dioxide coin cell
located on the system controller card
Printed circuit boards greater than 10 cm
2
11
25
– For MX710de, Lexmark MX710de3,
and MX711dthe (locations illustrated
in 4.2)
10 for MX710de and MX711dhe
9 for MX711de, Lexmark
MX711de3
– For MX812dtpe (locations illustrated
in 4.2)
24 for MX810/811/812 dpe, dxpe
23 for MX810/811/812dtme,
MX810/811/812dxme
22 for MX810/811/812dte, dme,
dtfe, dxfe
21 for MX810/811/812de, dfe, dxe
Toner cartridges, liquid and pasty, as well as colour
toner
1
Located inside front cover
Plastic containing brominated flame retardants
4 Fans;
46
Sensors;
8 Fuser
parts
Fan(s) and Sensors (locations
illustrated in 4.2)
Plastic parts located in the fuser
assembly marked with recycle code
that includes "FR17"or “FR16”
Asbestos waste and components which contain
asbestos
0
N/A
Cathode ray tubes
0
N/A
Chlorofluorocarbons (CFC), Hydrochlorofluorocarbons
(HCFC) or Hydrofluorocarbons (HFC), Hydrocarbons
(HC)
0
N/A
Gas discharge lamps
0
N/A
Liquid Crystal Display (LCD) greater than 100 cm2 and
those back-lighted with Gas discharge lamps
1
LCD located inside OP panel
External electrical cables
1
Power cord located on the back lower
left quadrant
Components containing refractory fibres
0
N/A
Components containing radioactive substances
0
N/A
Electrolyte capacitors containing substances of
concern1
10
Capacitor(s) located on Power Supply
(locations illustrated in 4.2)
1
With (height > 25 mm, diameter > 25 mm or proportionately similar volume)
Doc No.: Rev. 001 Page 2 of 18
3. Disassembly tools
Item
#2 Phillips screwdriver, magnetic
Wire cutter
E-clip puller or small flat-head screwdriver
Standard slotted head screwdriver
4. Disassembly references
4.1. Removal procedure(s)
MX710, MX810 series WEEE removal
WEEE materials and components removal procedures are available upon request.
Contact: recycling@lexmark.com
4.2. Graphical illustration of material’s and component’s location
See next page
Doc No.: Rev. 001 Page 3 of 18
MX710, MX810 Series
Location
Doc No.: Rev. 001 Page 4 of 18
MX710, MX810 Series
Location
Doc No.: Rev. 001 Page 5 of 18
MX710, MX810 Series
Location
Doc No.: Rev. 001 Page 6 of 18
Loading...