Page 1
Lexmark™ E360
Clearing Jams Guide
Clearing jams
Avoiding jams
The following hints can help you avoid jams:
• Use only recommended paper or specialty media. For more
information, see the User's Guide.
• Do not load too much paper. Make sure the stack height does
not exceed the indicated maximum heig's ht.
• Do not load wrinkled, creased, damp, bent, or curled paper.
• Flex, fan, and straighten paper before loading it.
• Do not use paper that has been cut or trimmed by hand.
• Do not mix paper sizes, weights, or types in the same stack.
• Do not feed envelopes that:
– Have excessive curl or twist
– Have windows, holes, perforations, cutouts, or embossing
– Have metal clasps, string ties, or folding bars
– Have an interlocking design
– Have postage stamps attached
– Have any exposed adhesive when the flap is in the sealed
or closed position
– Have bent corners
– Have rough, cockle, or laid finishes
– Are stuck together or damaged in any way
• Store the paper in an appropriate environment.
• Do not remove trays while the printer is printing.
• Do not load the multipurpose feeder while the printer is
printing. Load the multipurpose feeder prior to printing, or
wait for a prompt to load it.
• Push all trays in firmly after loading paper.
• Make sure the guides in the trays are properly positioned and
are not pressing too tightly against the paper.
• Make sure all sizes and types are set correctly in the printer
control panel menu.
• Make sure all printer cables are attached correctly. For more
information, see the setup documentation.
Identifying jams in the paper path
The following illustration shows the path that paper travels
through the printer. The path varies depending on the input
source (tray or feeder) and depending on whether a duplex
(two-sided) print job is being sent.
When a jam occurs, a jam message appears, indicating the region
of the jam or the number of jammed sheets. The three-digit jam
prefix numbers are given in the following illustration to show
where each jam occurs.
Understanding jam messages and locations
Note: To resolve any message, all paper or specialty media must
be cleared from the entire paper path.
Open doors and covers, and remove trays to access jam locations.
The following illustration and table indicate these locations. See
“Jam message numbers and how to access each jam” on
page 2 for a list of jam numbers and instructions for how to
access each jam.
Standard exit bin
1
Front door
2
Multipurpose feeder door
3
Tray 1
4
Optional 250- or 550-sheet tray (Tray 2)
5
Rear door
6
1
Page 2
Jam message numbers and how to access each
jam
Jam
number
200 Try one or more of the following:
To access the jam
• Remove Tray 1.
• Open the front door, and then remove the
photoconductor kit.
201 Open the front door, and then remove the
202 Open the front door, and then open the rear door.
231 Open the front door, and then open the rear door.
233 Remove Tray 1, and then depress the lever.
234 Try one or more of the following:
photoconductor kit.
Note: For alternative access to the jam, open the front
door, and then open the rear door.
• Open the front door, and then open the rear door.
• Remove Tray 1, and then depress the lever.
235 Remove the jam from the standard exit bin.
242 Remove Tray 2.
251 Open the multipurpose feeder door.
200 paper jam
1 Remove the tray from the printer.
2 Remove the jam if you see it here.
Note: When the photoconductor kit and toner cartridge are
together, they are called a unit.
4 Lift the flap in front of the printer, and remove any jammed
sheets.
3 If you do not see it, open the front door, and then remove the
photoconductor kit and toner cartridge (unit).
2
5 Align and insert the unit.
6 Close the front door.
7 Insert the tray.
8 Press .
Page 3
201 paper jam
202 paper jam
3 Open the rear door.
CAUTION—HOT SURFACE: The fuser and the inside of the
printer near the fuser may be hot. To reduce the risk of injury
from a hot component, allow the surface to cool before
removing paper from this area.
1 Open the front door, and then remove the unit.
2 Lift the flap in front of the printer, and then remove any
jammed sheets.
CAUTION—HOT SURFACE: The fuser and the inside of the
printer near the fuser may be hot. To reduce the risk of injury
from a hot component, allow the surface to cool before
removing paper from this area.
1 Open the front door, and then remove the unit.
4 Remove the jam.
2 Lift the flap in front of the printer, and then remove any
jammed sheets.
3 Align and insert the unit.
4 Close the front door.
5 Press
.
5 Close the rear door.
6 Close the front door.
7 Press .
3
Page 4
231 paper jam
CAUTION—HOT SURFACE: The fuser and the inside of the
printer near the fuser may be hot. To reduce the risk of injury
from a hot component, allow the surface to cool before
removing paper from this area.
1 Open the front door.
2 Open the rear door.
3 Remove the jam.
4 Close the rear door.
5 Close the front door.
6 Press .
233 paper jam
1 Remove the tray from the printer.
3 Pull the jammed sheets from the duplex area.
4 Insert the tray.
5 Press
If this does not clear the jam, complete the steps in “231 paper
jam” on page 4.
.
234 paper jam
A single jam or multiple jams are in the duplex area of the printer
when the printer is turned on. To locate and remove the jammed
sheets, complete all the steps in:
• “231 paper jam” on page 4
• “233 paper jam” on page 4
2 Locate the lever shown. Pull the level down to release the jam.
4
Page 5
235 paper jam
A duplex print job was sent to the printer using a size of paper not
supported for duplex printing. A sheet is jammed in the standard
exit bin.
1 To remove the jam, gently pull the jammed sheet out of the
standard exit bin.
2 Remove the jam.
3 Insert the optional tray.
If the sheet is not visible, complete the following steps:
1 Open the front door, and then remove the unit.
2 Lift the flap at the front of the printer, and then remove any
jammed sheets of paper that are short lengths of paper.
2 Press .
242 paper jam
1 Remove the optional tray from the printer.
4 Press
.
251 paper jam
A sheet of paper or specialty media failed to feed completely from
the multipurpose feeder. Part of it may be still visible. If it is visible,
gently pull the jammed sheet from the front of the multipurpose
feeder.
5
3 Align and insert the unit.
4 Close the front door.
5 Press
.
Loading...