USB Wireless Adaptor User Manual
150Mbps USB Wireless Adaptor User Manual
一、Network Card Installation
Please follow the following steps to install your new wireless network card:
1. Insert the USB wireless network card into an empty USB2.0 port of your
computer when computer has power on. Never use force to insert the card, if
you feel it’s stuck, flip the card over and try again;
2. Insert device driver CD into the CDROM drive of your computer, double click
the ‘Setup.exe’ icon and run the ‘Setup.exe’ program;
3. Select ‘I accept the terms of the license agreement’, and then click ‘Next’;
4. Select the setup type that best suits your needs, ‘Install driver and Ralink
WLAN Utility’ are recommended;
1
USB Wireless Adaptor User Manual
5. Click ‘Next’ , show the ‘Select Configuration Tool’ dialogue, you can manage
this wireless adapter both by “Ralink Configuration Tool” and “Microsoft Zero
Configuration Tool”;
6. Click ‘Next’, and Show ready to install dialogue;
2
USB Wireless Adaptor User Manual
7. Click ‘Install’, and the installation is in process;
8. Finally, click ‘Finish’ to finish the driver installation;
3
USB Wireless Adaptor User Manual
4
USB Wireless Adaptor User Manual
二、Connect to Wireless Access Point
1. After installation has finished, it will try to connect to any unencrypted
wireless access point automatically. If you want to connect a specific wireless
access point, or the access point you wish to connect uses encryption, you have
to configure the wireless network card and input the correct password to get
connected to the wireless access point. Double click to open desktop lower
icon ;
2. Displays the following picture;
3. Click the icon ; Scan available wireless access point. Scan results will
display in the ‘Network’ zone. If you can’t find the access point you wish to
connect here, click the Refresh button, until you can find your wireless
access point;
5
USB Wireless Adaptor User Manual
4. Choose the wireless access point’s SSID, and double-click it. If the AP is
encrypted, you should follow the prompts to select the appropriate encryption
type and enter a password;
5. After you have connected to the wireless access point successfully, you can
get the detail information of connected access point, such as status、IP address、
6
USB Wireless Adaptor User Manual
speed and so on. Click the icon ，then the ，you will see the signal quality
and signal strength information.
7
USB Wireless Adaptor User Manual
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However,there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the useris encouraged to try to correct the interference
by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible forcompliance could void the user’s authority to operate this equipment. (Example- use only
shielded interface cables when connecting to computer or peripheral devices)
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
This equipment should be installed and operated with minimum distance 0.5cm between the radiator and your body.
The antenna is external antenna(Reserve SMA-type). And is rotatable.
SAR restriction applies to this dedicated antenna.SAR compliance is restricted to the dedicated external
dipole antenna with an antenna gain of 4 dBi. The use of any other antenna type or antenna with higher
gain is not permitted.
8
Loading...