Level One IGP-1271 quick start Guide
Quick Installation Guide
( TURING™ Industrial Series )
V1.0
Digital Data Communications GmbH, Germany.
http://www.level1.com
- 1 -
Content
English ....................................................................................................2
Deutsch........................................................................................................
Français ...................................................................................................8
Español ..................................................................................................11
Italiano ......................................................................................................
Português ...................................................................................................
..14
..5
17
This Quick Installation Guide only describes the most basic situations and
settings. All detailed information is described in the user manual.
- 2 -
English
Serial
number
Name
Quantity
Note
1
Master unit
1
Required
2
Quick Installation Guide
1
Required
3
Resource CD (User Manual, QIG)
1
Required
4
Console Cable (Not included with No Console Port model)
1
Required
5
Din-rail Mount Kit
1
Required
Package Contents
This product is provided with the following accessories in the box; please check them carefully. If
any of the accessories is missing or damaged, please contact with your local dealer timely.
1.Power connection (DC Industrial Power Supply unit is to be ordered
separately)
• This unit provides 4 pin terminal block.
Power connecting procedure:
STEP 1 – Pull out 4 pin terminal block.
STEP 2 – Connect wire to P1+, P1-, or P2+, P2-, and Ground the neutral wire to the ground screw.
STEP 3– Plug back 4 pin terminal block to its place.
- 3 -
2.Perform Initial Configuration (For model with console port)
Note:
For further information on switch configuration, refer
to the
Web Management Guide and CLI Reference Guide.
1.Connect a PC to the switch console port using the included console cable.
2. Configure the PC’s serial port: 115200 bps, 8 characters, no parity, one stop bit, 8 data bits, and no flow
control.
3.Log in to the CLI using default settings: Username “admin”
and password “admin.”
3.Logging on to the equipment
1.
Connect the RJ-45 interface cable of a switch with a computer using a network cable.
2.
Set the TCP/IP properties of the computer, see the Appendix: Setting up your computer.
3.
Logging on to the equipment: Open a browser and type 192.168.1.1 in the address bar, and then
press Enter; in the pop-up login interface, enter the factory logon username "admin", password
"admin" and click OK.
- 4 -
4.Appendix: Setting up your computer
■ Windows
1.
Click Start—> Control Panel—> Network and Internet—> Network and Sharing Center—
> Change adapter settings, right click Local connection and select Properties;
2.
Double-click Internet Protocol 4 (TCP/IPv4);
3.
Set the computer's IP address: The computer's IP address should be any one of the following
free IP addresses 192.168.1.2 ~ 192.168.1.254, and then click OK, to return to the previous
page, click OK.
- 5 -
Deutsch
Seriennummer
Name
Anzahl
Hinweis
1
Hauptgerät
1
Erforderlich
2
Schnellinstallationsanleitung
1
Erforderlich
3
Ressource CD (Bedienungsanleitung, QIG)
1
Erforderlich
4
Konsolenkabel (Nicht im Lieferumfang des No
Console Port-Modells enthalten)
1
Erforderlich
5
DIN-Schienen-Montageset
1
Erforderlich
Lieferumfang
Dieses Produkt wird mit folgendem Zubehör geliefert; bitte prüfen Sie den Lieferumfang sorgfältig.
Falls ein Teil fehlen oder beschädigt sein sollte, wenden Sie sich bitte möglichst bald an Ihren
örtlichen Händler.
1.Stromanschluss (DC Industrielles Netzteil ist separat zu erwerben)
• Dieses Gerät verfügt über einen 4-poligen Anschlussblock.
Stromanschlussverfahren:
Schritt 1 – 4-poligen Anschlussblock herausziehen.
Schritt 2 – Draht mit P1+, P1- oder P2+, P2- und Erde, Neutralleiter mit Erdungsschraube verbinden.
Schritt 3 – 4-poligen Anschlussblock wieder anbringen.
Loading...