LevelOne FCS-3083, FCS-3055, FCS-3082 User Manual

Fixed Dome Network Camera
Hardware User Manual

FCS-3055, FCS-3082, FCS-3083

Ver.2014/01/15

Hardware Manual

2

Table of Contents

Precautions ....................................................................... 4

Safety Instructions ................................................................................................... 6

Introduction ..................................................................... 7

The List of Models ................................................................................................... 7

Ou Package Contents ............................................................................................... 8

Physical Description ................................................................................................ 9

Installing the Camera on a Surface .............................. 11

Step 1: Drill the Holes ............................................................................................ 11

Step 2: Open the Dome Cover .............................................................................. 12

Step 3: Prepare for Waterproof Installation........................................................ 14

Waterproof Solution with Naked Cable ................................................. 15

Waterproof Solution with Conduit .......................................................... 17

Step 4: Install the Camera to the Surface ............................................................ 21

Step 5: Connect the Cable(s) ................................................................................. 22

Step 6: Access the Camera Live View .................................................................. 23

Step 7: Adjust the Viewing Angle ......................................................................... 23

Step 8: Close the Dome Cover .............................................................................. 24

Other Connections ......................................................... 25

Connecting DI/DO and Audio Devices (Optional) .............................................. 25

How to Connect DI/DO Devices ............................................................ 25

How to Connect Audio Devices ............................................................. 29

Hardware Manual

3

Other Adjustments and Accessories ............................. 30

How to Adjust the Viewing Angle ........................................................................ 30

FCS-3055 / FCS-3082 / FCS-3083 ....................................................... 30

How to Install / Remove the Memory Card......................................................... 31

How to Insert the Memory Card ............................................................ 31

How to Remove the Memory Card ........................................................ 31

How to Replace the Dome Cover .......................................................................... 32

Accessing the Camera.................................................... 35

Configure the IP Addresses ................................................................................... 35

Access the Camera ................................................................................................. 39

Hardware Manual

4

Precautions

Read these instructions

You should read all the safety and operating instructions before using this product.

Heed all warnings

You must adhere to all the warnings on the product and in the instruction manual. Failure to follow
the safety instruction given may directly endanger people, cause damage to the system or to
other equipment.

Servicing

Do not attempt to service this video device yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Trademarks

All names used in this manual are probably registered trademarks of respective companies.

Liability

Every reasonable care has been taken during the writing of this manual. Please inform your local
office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.

Hardware Manual

5

Federal Communications Commission Statement

This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to the equipment that are not expressly approved by the
responsible party for compliance could void the user’s authority to operate the equipment.

European Community Compliance Statement

This product has been tested and found to comply with the limits for Class B

Information Technology Equipment according to European Standard EN 55022
and EN 55024. In a domestic environment, this product may cause radio interference in which
cause the user may be required to take adequate measures.

Hardware Manual

6

Safety Instructions

Cleaning

Disconnect this video product from the power supply before cleaning.

Attachments

Do not use attachments not recommended by the video product manufacturer as they may cause
hazards.

Do not use accessories not recommended by the manufacturer

Only install this device in a dry place protected from weather

Servicing

Do not attempt to service this video product yourself. Refer all servicing to qualified service
personnel.

Damage Requiring service

Disconnect this video product from the power supply immediately and refer servicing to qualified
service personnel under the following conditions.

1) When the power-supply cord or plug is damaged

2) If liquid has been spilled, or objects have fallen into the video product.

3) If the inner parts of video product have been directly exposed to rain or water.

4) If the video product does not operate normally by following the operating Instructions in this

manual. Adjust only those controls that are covered by the instruction manual, as an improper
adjustment of other controls may result in damage, and will often require extensive work by a
qualified technician to restore the video product to its normal operation.

Safety Check

Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.

Hardware Manual

7

Introduction

The List of Models

This hardware manual contains the following models:

FCS-3055

Fixed Dome Network Camera, 3-Megapixel, Outdoor, PoE 802.3af, Day
& Night, IR LEDs, WDR

FCS-3082

Fixed Dome Network Camera, 3-Megapixel, Outdoor, PoE 802.3af, Day
& Night, IR LEDs, WDR

FCS-3083

Fixed Dome Network Camera, 5-Megapixel, Outdoor, PoE 802.3af, Day
& Night, IR LEDs, WDR

From the installation perspective, these models are similar; therefore, one manual is used for all
of them.

Hardware Manual

8

Package Contents

Camera

Mounting Screw Kit

Hexagon Screwdriver

Drill Template

Conduit Gland

Cable Gland

Lens Focus Tuner

(for D7xA / E7xA only)

Terminal Block
(for Audio and DI/DO)

Quick Installation Guide

Drill Template

Hardware Manual

9

Physical Description

NOTE: The camera picture above is for reference only. Actual camera may slightly differ.

1) Ethernet Port

Connects to a network using an Ethernet cable.

2) Memory Card Slot

Insert a memory card (not included) into this slot for local recording purposes. See How to

Install / Remove the Memory Card on page 31 for more information.

NOTE: Supports microSDHC and microSDXC cards.

3) Reset Button

The purpose of the reset button is to restore the factory default settings of the camera,
including the administrator’s password.

When to use the reset button?

1. The administrator’s password has been forgotten and therefore the camera cannot be
accessed.

2. In case of IP address, mask, or allow/deny filter related issues, resulting with inability to
modify these settings.

3. In case of connectivity issues or abnormal video quality.

How to do the reset?

Press and hold the reset button for 5 seconds.

Hardware Manual

10

4) Digital Input / Output (DI/DO) and Audio Input / Output

This connector connects to digital input or output devices, such as an alarm trigger, panic
button, etc., as well as audio input and output devices, such as microphones and speakers.
Digital Input (DI) and Digital Output (DO) devices are used in applications like motion
detection, event triggering, alarm notifications, etc. See Connecting DI/DO and Audio

Devices (Optional) on page 25 for more information.

Hardware Manual

11

Installing the Camera on a Surface

This section describes the procedures in installing the camera on a flat surface such as a hard or
dropped ceiling and straight or tilted walls. Before installation, make sure the wall or ceiling can
bear more than the weight of the camera.

Step 1: Drill the Holes

Before drilling the holes, note the direction of the connectors side of the camera, which is also the
opposite side of the camera logo. This influences the camera placement and where you should
drill the hole where the cables will pass through or how the cables will go along the ceiling or wall.

1. According to the preferred camera orientation, mark the screw holes location on the surface.

2. Determine how the cables will be routed: pass through the surface or along the surface.
 If the cables will pass through the surface, drill the cable hole and the three (3)

screw holes on the surface.

 If the cables will be routed along the surface, just drill the three (3) screw

holes on the surface.

3. Insert the plastic plugs into the screw holes, if necessary.

Hardware Manual

12

Step 2: Open the Dome Cover

NOTE: To avoid scratches or leaving fingerprints on the dome cover, it is recommended to retain

the plastic covering the dome cover until the camera is completely installed. However, the plastic
has been removed on the pictures in this documentation to show clarity of the procedures being
described.

1. If the cables will pass through the surface, remove the metal cap covering the bottom conduit

hole of the camera, and attach the cap to the side hole to close it. The cable(s) will be routed
to pass this hole from the surface.

2. Loosen the three (3) screws securing the dome cover.

Hardware Manual

13

3. Carefully lift to open the dome cover and place it on the side of the camera.

NOTE: Do not abruptly lift the dome cover; it is attached to the camera with a spring wire.

4. If necessary, insert a memory card with the metallic contacts facing down into the card slot of

the camera.