Lenovo Q200 User Manual
www.lenovo.com
Version 1.0
WORLDWIDE PARTNER
IdeaCentre Q User Guide
31032755
31032755_UG_FM_EN.indd 1 2007.12.21 2:44:32 PM
Danger: Watch out for high risks
Caution: Watch out for medium risks
Attention: Pay attention to low risks
Prohibition: Dangerous operations
Recommendation: Helpful tips
Key to signs used in this manual
31032755_IdeaCentre Q-UG.indd 1 2007.12.21 2:28:49 PM
31032755_IdeaCentre Q-UG.indd 2 2007.12.21 2:28:49 PM
1
Table of contents
Table of contents
Key to signs used in this manual
Chapter 1 Instructions for using computer hardware ........... 1
1.1 Front View of the Chassis ........................................................2
1.2 Rear view of the chassis ..........................................................4
1.3 Notes on computer cabling and installation ..............................7
1.4 Keyboard and Mouse ..............................................................
7
1.5 Using the Remote Control ......................................................
11
Chapter 2 Lenovo Computer Rescue System Operation
Instruction ..............................................................
15
2.1 Installing Drivers and Software Shipped with Computer .........16
2.2 OneKey Recovery .................................................................
17
2.3 File Management ..................................................................
21
2.4 OneKey Antivirus ...................................................................
22
Chapter 3 Using the software ................................................ 25
3.1 Power2Go — Burning Discs ..................................................26
3.2 Lenovo Healthcare Software ..................................................27
3.3 PC-cillin
................................................................................30
3.4 Lenovo Media Studio .............................................................
31
3.5 Veriface (Only for computer which is shipped with camera) ....
32
3.6 Earth link (Only for United States ) .........................................33
Chapter 4 System maintenance and recovery ..................... 35
4.1 Restoring the system .............................................................36
4.2 Cleaning up the disk ..............................................................
36
4.3 Checking for, and correcting disk errors .................................
37
4.4 Defragmenting the disk(s) ......................................................
37
4.5 Performing daily maintenance tasks .......................................
37
31032755_IdeaCentre Q-UG.indd 1 2007.12.21 2:28:50 PM
2
Table of contents
Chapter 5 Troubleshooting and Confirming Setup .............. 39
5.1 Troubleshooting display problems ..........................................40
5.2 Troubleshooting audio problems ............................................
40
5.3 Troubleshooting software problems .......................................
41
5.4 Troubleshooting problems with optical drives and hard
disks .....................................................................................
42
5.5 Special considerations for troubleshooting Windows .............
43
31032755_IdeaCentre Q-UG.indd 2 2007.12.21 2:28:50 PM
1
2
3
4
5
Chapter
Instructions for using computer
hardware
This chapter describes some of the operations
commonly performed during routine use of the
computer, including the proper connection of
components. Please read it carefully.
The description of the TV card in this manual is only
used for the machines which have the TV card. It
is invalid for those machines which do not have TV
card.
Note: The configuration of your computer
model may vary slightly from the illustrations
used in this document.
User Guide
1
31032755_IdeaCentre Q-UG.indd 1 2007.12.21 2:28:14 PM
2
User Guide
1.1 Front View of the Chassis
Instructions for the use of buttons and functional keys that are located at the
front of the computer.
F-1
F-2
F-3
F-4
F-1 Power switch: Press this button to turn on / off the computer.
F-2 Hard disk light: Indicates the read /write status of the hard disk.
F-3 Power light: Indicates the status of the power.
F-4 Front Digital Panel: Open the front digital panel. You can now see the front
digital connectors.
31032755_IdeaCentre Q-UG.indd 2 2007.12.21 2:28:15 PM
3
User Guide
Front Digital Panel:
D-4
D-1
D-2
D-3
D-5
D-1
MS/Pro/Duo/ProDuo
CF/I/II/MD
xD
SD/Mini/HC/MiniHC
MMC/RS/Plus/Mob
D-1 USB Connectors: To connect USB devices.
D-2 Microphone Connector: To connect the microphone and pass the
microphone audio input to the computer.
D-3 Speakers/Headphones Connector: To connect speakers or headphones. If it
is necessary to connect the headphones, remove the speaker plug and insert
the headphones plug.
D-4 Optical drive
D-5 Memory card reader Connector: Able to read/write data from CompactFlash
I/II/MD, xD, MS/Pro/Duo/Pro Duo, SD/Mini /HC/Mini HC/MMC/RS/Plus/Mobile
memory cards.
31032755_IdeaCentre Q-UG.indd 3 2007.12.21 2:28:15 PM
4
User Guide
1.2 Rear view of the chassis
Instructions for the use of all I/O interfaces on the rear panel of the computer.
The following illustrations show connections located at the rear of some computer
models. The locations of connectors on your computer will be similar to, but
possibly not identical to these. Following the illustrations is a key that explains the
symbol callouts used in the figures.
X-1
X-2
T-2
V-2
S
DVI
X-2
L&R
FM
T-2
V-2
V
S
V-2 ———— The external VGA Card may have some of these connectors, but
not have all of them. Use the correct connector according to the
31032755_IdeaCentre Q-UG.indd 4 2007.12.21 5:09:42 PM
5
User Guide
monitor you used.
T-2
———— The TV Card may have some of these connectors, but not have all
of them. Use the correct connector according to the usage.
Key to symbols used in the above illustrations of the rear of the
chassis:
——— Power Connector: To supply power to the computer.
———— PS/2 Mouse Connector: To connect a mouse having a PS/2
connector.
—— PS/2 Keyboard Connector: To connect a keyboard having a PS/2
connector.
—— Serial Connector: To connect devices requiring a serial connection.
(COM Connector )
——— Parallel Connector: To connect devices requiring a parallel
connection.
X-1 —— On-board VGA Card Connector: To connect with the signal cable
of a monitor. On computer models that have an external graphics
card, on-board graphics card signals are shielded and there are
no VGA signal outputs - some models are equipped with this
connector.
——— USB Connector: To connect USB devices.
—— Ethernet Connector: To connect LAN or broadband network
devices.
X-2 —— External VGA Card Connector: To connect with the signal cable
of a monitor. It connects with the data cable of the monitor. (Some
models are equipped with this connector.)
DVI —— External DVI Card Connector: To connect to the data cable of the
DVI connector. (Some models are equipped with this connector)
31032755_IdeaCentre Q-UG.indd 5 2007.12.21 2:28:18 PM
6
User Guide
S ——— S Video Connector: To connect the data cable of the S video. (Some
models are equipped with this connector.)
V ——— Video Connector: To connect with the Video to S-Video converting
cable provided in the computer. (Some models are equipped with
this connector.)
FM
———— FM Antenna Connector: To connect an FM antenna provided with
the computer. (Some models are equipped with this connector.)
———— TV Antenna Connector: To connect the signal input cable for the
CATV. (Some models are equipped with this connector)
L&R
——— Left and right audio connector: Audio input connector. (Some
models are equipped with this connector.)
——— Audio Line-in Connector: To connect audio input to the computer.
— Audio Line-out Connector: To connect to the speakers or
headphones.
———— Microphone Jack: To connect to audio input from a microphone.
Voltage selection switch (Some models are equipped with this switch)
Check the position of the voltage-selection switch on the rear of the computer. Use
a ballpoint pen to slide the switch, if necessary.
1. If the voltage supply range is 100-127 V ac, set the switch to 115 V.
2. If the voltage supply range is 200-240 V ac, set the switch to 230 V.
115
2
3
0
Figure 1 Figure 2
31032755_IdeaCentre Q-UG.indd 6 2007.12.21 2:28:20 PM
7
User Guide
1.3 Notes on computer cabling and installation
1. Connect the monitor signal cable to the on-board graphics card connector if the
model you purchased is not equipped with an external graphics card.
2. If there is an external graphics card, connect the monitor signal cable to the
VGA or DVI connector in the external graphics card.
3. If both your computer and monitor have the DVI connector, you can connect the
computer to the monitor through your own DVI data cable.
4. If there is only DVI connector in the external graphics card and the monitor only
have the VGA connector, connect the monitor data cable and DVI connector by
the DVI-VGA converter
.
Notes:
• Keep speakers away from the monitor to avoid magnetic interference.
• Ensure the monitor-to-computer cable connections are secure, with screws
tightened.
• Connect the monitor signal cable to the on-board graphics card connector if
the model you purchased is not equipped with an external graphics card.
1.4 Keyboard and Mouse
This computer adopts wireless keyboard and mouse. The wireless keyboard and
mouse of this computer adopt advanced wireless connection technology instead
of the traditional wire devices. The data may be transmitted between the keyboard,
mouse and the computer in effective distance through wireless signals, which
enables free selection of space.
+
-
×
-
L
V
T
— Opens the LVT navigation menu
31032755_IdeaCentre Q-UG.indd 7 2007.12.21 2:28:21 PM
8
User Guide
+
-
×
-
—— Opens the calculator program
—— Opens default E-mail box of the system
—— Opens default homepage of the IE explorer
—— Play/Pause button
—— Turns down the volume
—— Turns up the volume
—— Mute
F2
—— For computers configured with [Rescue System] function, press F2
when “Lenovo” display on the interface to start [Rescue System].
[K-1][K-2]
[K-2]
[K-1]
[K-1] — Battery compartment
[K-2] — Wireless Reset button
31032755_IdeaCentre Q-UG.indd 8 2007.12.21 2:28:25 PM
9
User Guide
1. Establishing wireless connection of wireless keyboard
[L-1]
1)
[L-1] Connect the USB interface of the computer: Connect the attached
USB wireless receiver to the USB interface of the computer to receive wireless
signals.
2)
[K-1][K-2]
[K-1]
Start the computer and enter the system. Put the battery in the battery compartment
of the keyboard and mouse [K-1], as shown in the figure above.
Note: Check whether the battery of the keyboard and mouse has sufficient
power and is installed correctly, and whether the anode and cathode of the
battery is installed reversely; otherwise the device will not work normally or
will be damaged.
31032755_IdeaCentre Q-UG.indd 9 2007.12.21 2:28:26 PM
10
User Guide
3)
≤25CM
Wireless Reset
button
OF
F
ON
R
S
S
E
T
Connect to the USB
connector of computer
Start computer, enter the system, connect the USB wireless receiver to the USB
interface of the computer, and then the system will identify and install USB driver
automatically.
Press the Wireless Reset button on the keyboard and mouse, and then press the
Wireless Reset button on the USB wireless adapter of the computer within two
seconds to establish the wireless connection.
If it fails, repeat the above procedure.
Note: In the process of establishing connection, it is recommended to
keep the distance between the Keyboard , mouse and computer to be
less then 25cm.
2. Notes for using wireless keyboard
Specifi cations:
1) The keyboard needs two AA batteries to supply power.
2) The effective working distance of the wireless keyboard is 2m (depending on the
operating environment of the computer).
If the wireless device does not work, check as follows:
1. Restart the computer, and check whether the system devices are running well.
2. Repeat the procedure for establishing wireless connection.
3. Replace batteries.
4. Do not place the computer under the metal table.
31032755_IdeaCentre Q-UG.indd 10 2007.12.21 2:28:28 PM
Loading...