Lennox Hearth H6963 User Manual

HEARTH PRODUCTS

KITS AND ACCESSORIES

INSTALLATION INSTRUCTIONS FOR THE REFLECTIONS ELECTRIC FIREPLACE

TELEVISION REPLACEMENT KIT (NUMBER: H6963)

REPLACEMENT INSTRUCTIONS

Removal Of The Existing TV From The Reflections Electric Fireplace

Step 1. Disconnect the electrical power to the fireplace.

Step 2. Remove the doors from the fireplace.

Step 3. See

Keep the two (2) door clips and screws to be used again upon re­assembly.

Figure 1

for the location of the door track and remove it.

P/N 506019-19
REV. N/C 01/2008

Glass Information

• This unit will not operate properly with missing or broken glass.

• Do not strike or slam the glass.

• Do not use abrasive cleaners to clean the glass.

• This appliance uses tempered glass. Replacement of the glass as

supplied by the manufacturer should be done by a qualified service
technician.

Step 5. Remove the Logs.

Step 6. Remove the Grate.

Step 7. Remove the Ember Bed.

REFLECTIONS TELEVISION

REPLACEMENT KIT

Door

Track

Figure 1

Step 4. Remove the reflective glass. To access the logs, grate embers

and lights, the glass panel needs to be removed. For an illustration of
the glass panel installation, (refer to

First sweep the screens inward and tie up and out of the way. The glass
is not secured by any fasteners. The back rests on two insulated tabs and
the front is hooked behind a lip.

CAUTION: WHEN REMOVING THE GLASS, DO NOT LET THE BACK
OF THE PANEL SLIP OFF OF THE INSULATED TABS IN THE BACK.
THIS COULD ALLOW THE GLASS TO DROP INTO THE REFRACTORY
PANELS OR LOGS AND BREAK THEM.

The lower front corners of the glass are exposed to provide a place
to grip the glass panel. Grip the corners firmly; lift the panel back
and up against the top of the unit.

Disengage the glass from behind the front lip and rotate the front
upwards. Slide one hand under the glass and support the panel.
Draw the glass out of the unit and set it carefully aside.

Figure 8, on page 4 )

.

Step 8. Disconnect and label the video and audio cables from the TV and
remove the IR module.

Step 9. Locate the two locking screws that secure the television
assembly and remove them (

see Figure 2

).

Latch

Rod

Figure 2

Step 10. Press upwards on the latching rods to free the television

assembly. Once free, the assembly will rotate down to a vertical position
hanging from the screen rods (

refer to Figure 3

Locking Screw

).

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

1

Power Cord

Tabs

Engagement Hooks

Figure 3

CAUTION: THE TELEVISION ASSEMBLY IS HEAVY. PLEASE CLEAR
THE AREA IN FRONT OF THE FIREPLACE BEFORE ATTEMPTING TO
SWING THE UNIT INTO POSITION. THE UNIT MUST SWING
SLIGHTLY PAST HORIZONTAL TO LATCH. WE SUGGEST THAT TWO
PEOPLE PERFORM THIS STEP.

Step 11. Lift the assembly upwards to free it from the screen rods.

Hand Holds

Screen Rod

Detail Of

Top Receptacle

Top Receptacle

Television
(Face Down)

Step 12. Lay the television tray assembly onto a flat surface. Use a

cardboard protector to protect the tray from marring.

Step 13. Undo the straps to remove the existing TV.

INSALLING THE REPLACEMENT TV

Step 1. Open the television box and remove all packing materials from

the unit. Remove the television and place it beside the tray.

Note: The Television is provided with a remote control. The fireplace
does not require this remote control. It may be discarded.

Drape the straps to the side of the tray assembly, out of the way as
much as possible.

The television will lay face down on the tray as shown in
The television is oriented centrally on the tray with the bottom
against the base support. The straps are then doubled over the unit
as shown in
tightly (with straps provided inside carton support package) to
prevent the television from slipping out of position.

Note: The TV screen protrudes below the bottom frame of the tray
assembly. Be sure to support the tray assembly above the work surface
to protect the TV screen. Use the spacers from the TV box to do this.

Lift the assembly up onto its base (as shown in
the security of the straps. Use the handles on each side of the unit to

lift and hold the unit.

CAUTION: THE SECURITY OF THE STRAPS IN THIS ASSEMBLY IS
IMPORTANT SO THAT THE INSTALLATION STEPS THAT FOLLOW
CAN BE PERFORMED SAFELY.

2

Figure 4

and drawn very taut. Cross strap both sides

Figure 3

Figure 4

) and verify

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Tray
Assembly

Use

.

Center Slot

Television
Straps

Spacers

Secure Television

Straps Tightly

Cross
Strap

Handles

Television

Base

Base Support

Figure 4