Lenco Xemio 657 User's Guide
USER’S MANUAL
Xemio-657
MP3/MP4 Media Player with 4GB memory
1
For information and support: www.lenco.com
2
Cautions
Do not place naked flames, such as lighted candles on or near the
product.
Do not place objects filled with liquids, such as vases on or near
the product.
Do not use or store this product in a place where it is subject to
direct sunlight, heat, excessive dust or vibration.
Do not use this product with wet hands.
Do not clean this product with water or other liquids.
Do not block or cover the slots and holes in the product.
Do not push foreign objects into the slots or holes in the product.
Do not attempt to open this product yourself. There are no user
serviceable parts inside.
Do not allow children access to plastic bags.
Safety Warnings
Before using this product, read and follow all warnings and
instructions.
This product is not intended for use by young children. Young
children should be properly supervised.
This product is intended for household use only and not for
commercial or industrial use.
3
Do not expose to dripping or splashing.
No naked flame sources, such as lighted candles, should be
placed on the product.
Ventilation should not be impeded by covering ventilation openings
with items such as newspapers, table cloths, curtains and the like.
Make sure the unit is adjusted to a stable position. Damage
caused by using this product in an unstable position or by failure to
follow any other warning or precaution contained within this user
manual will not be covered by warranty.
We, suggest retaining the packaging in case for future transport of the
product.
If at any time in the future you should need to dispose of this
product please note that: All batteries and accumulators need to be
removed from this product (Removal of Waste Batteries and
Accumulators).
WARNIN
When participating in the traffic listening to a personal
music player can make the listener less aware of
potential dangers such as approaching cars.
4
G:
WARNIN
G:
Prolonged exposure to loud sounds from personal
music players may lead to temporary or permanent
hearing loss.
1. Get to know the controls on Player
5
Item Description
1 TFT LCD Display
2 Button (On / Off, Play / Pause)
3 Button (Previous / Fast-Rewind)
4 Button (Next / Fast-Forward)
5 M Button (Menu)
6 Button (Previous Menu / Exit)
7 Micro USB Port (PC Connection / Charge)
8 Microphone Position (mono, inside USB port)
9 Micro SD Memory Card Slot
10 Earphone Output Jack (3.5mm Stereo)
11 Button (Volume Down)
12 Button (Volume Up)
2. About Player Battery
Player has an internal, non–user-replaceable battery. For best
results, the first time you use player, let it charge for about 2 ~ 3 hours
or until the battery status icon in the “Connect” screen shows that the
battery is in full.
6
Battery is in full
Note: Player may continue use battery power after it’s been turned
off. For maintain the battery life and performance, if unit isn’t used for
a while, the battery need to be recharged, recharging the battery at
least once per month.
a. Charging the Battery:
You can charge the player battery in two ways:
Connect player to your computer. Or,
Use the USB power charger. (not included)
b. Connection and Charging:
Once you have connected player with computer / power charger,
then you will see the “Connect” screen appear on screen,
The level bars are running in battery status icon at the “Connect”
screen. The battery is in charging.
“Connect” Screen
7
In Charging
Important: The battery does not charge when your computer is in
sleep. The USB port on most keyboards does not provide enough
power to charge the player. Connect player to a USB 2.0 port on your
computer only to prevent charge problem.
3. Connecting and Disconnecting Player
You can connect the player with your computer to transfer those
media files and recorded voice memos when necessary, and to
charge the battery.
8
a. To Connecting Player
To connect player to your computer, plug the connector of USB
Cable into a USB port on your computer, and connect the other
end to player, then the “Connect” screen appear for view.
Now the player is ready for media files transfer with your computer
and the battery is charging.
You can transfer the media files by using the computer mouse use
drag and place, or copy and paste, in between the player and your
computer. Disconnect it when you’re done.
b. To Disconnecting Player
It’s important not to disconnect player while it’s syncing or
transferring files. Eject the player before disconnect it.
To eject player, press and hold M button for about 2 seconds, the
“Connect” screen will switch to “Main Menu” screen. And now is
safe to disconnect the player with your computer. Unplug the USB
cable from the player. Or,
If you’re using a Windows PC, you can also eject player in My
Computer or by clicking the “Safely Remove Hardware” icon in
the Windows system tray, select the correspondence name of USB
Device and choose “Stop” > choose “Confirm” > choose
“Confirm” follow by the pop up windows you’re your computer.
9
If you’re using a Mac, you can also eject player by dragging the
player icon on the desktop to the Trash.
Disconnect the USB cable from the player and computer, simply
remove it.
If you accidentally disconnect player without ejecting it, reconnect it
to your computer and sync again. However, some media file may
loss.
4. Getting Start the Player
Turn ON / OFF the player and use of Main Menu.
Press and hold the button for 3 seconds to turn ON, then you will
see any one of the following shown Main Menu screen, Music /
Movie / Record / Voice / Photo / eBook / Game / Setup, will
appear on LCD after the Loading and Opening screen have
displayed.
To OFF the player, press and hold the button for 3 seconds.
“Main Menu” screens
10
5. Use Setup Menu
You might need to set date & time or change some default setting
as you desired in setup sub menu before you start to use the player.
To go into setup menu, from main menu, choose “Setup” by use
/ button and then press button, a “Setting” menu appears to
use.
You can go back to previous menu by press the button during in
setup menu. Or, press and hold the button to return to main
menu.
Setup Menu
11
(Menu Page 1) (Menu Page 2)
a. To Setup “System time” (Date & Time):
Choose “System time” by using / button and then press
button, a date & time setting screen appears to use.
Press “ ” button, the year is highlighted then adjusting to current
year by pressing the / button. And repeating the adjusting
methods by “ / ” and / button again for finished those
items; Month, Date, Hour, Minute and seconds setting adjustment.
Finally, you need to press the button to confirm the adjustment
and back to Setup menu, if not the date & time will not to memorize
and you need to adjust them again.
Note: the set date & time will be losses if internal rechargeable
battery is fully emptied in protection mode. Adjust the clock again if
you want it to use.
b. To change “LCD set”
You can set the backlight to illuminate the screen for a certain
amount of time as you desired or make the backlight to always ON
12
when every time you turn ON the player.
To change LCD backlight, choose “LCD set” > choose “Dark
mode”, a level bar with number appear then chose “0 (always
On) / 5 / 10 / 15 / 20 / 25 / 30 / 35 / 40 / 45 / 50 seconds” as you
desired by using and / buttons. Choose “0” to prevent the
LCD backlight from turning to off. (choosing this option decrease
battery performance)
c. To Change “Language”
This player can use difference OSD languages.
To set the language, choose “Language”, and then choose which
language as you desired by using and / buttons.
d. To Set “Power Off”
The Power Off setting can extend the time between battery
charges by turning OFF the player when you are not using the
controls or no operation. Also, Sleep function provided for more
choice.
To set power off time, choose “Power off”, then choose “Off time”,
a levels bar with number menu appear, then choose “0 - 200
seconds” as you want by using and / buttons.
To set sleep time, choose “Power off”, then choose “Sleep time”, a
levels bar with number menu appear, choose “0 / 10 / 20 /30 / 40 /
13
50 / 60 / 70 / 80 / 90 / 100 / 110 / 120 minutes” as you want by
using and / buttons.
e. To View “Memory info”
You can view about the memory status of player, such as the
numbers of remaining memory space available and the percentage of
memory have used.
To view the status, choose “Memory info” by using and /
buttons. An information screen, remaining memory space available
and percentage of memory used, appear for view.
To return to setup menu or main menu press button or press and
hold button.
f. To View “Firmware Version”
You might need to view the details about firmware information
inside the Player.
Choose “Firmware version” by using and / buttons, an
information screen appear for view.
To return to setup menu or main menu, press button or press
and hold button.
g. To “Exit”
Select Exit to back to main menu. Or, press and hold the button
to go back main menu.
14
Loading...