LD Systems LDSAT42G2W User Manual [en, de, fr, es, pl, it]

USER´S MANUAL BEDIENUNGSANLEITUNG MANUEL D`UTILISATION MANUAL DE USUARIO INSTRUKCJA OBSŁUGI MANUALE D‘ USO

LD SATG²/SUB SERIES

PASSIVE INSTALLATION SPEAKER: LDSAT42G2(W) / LDSAT242G2(W) /

LDSAT62G2(W) / LDSAT82G2(W) / LDSUB88 POWERED INSTALLATION SPEAKER: LDSAT62AG2(W) / LDSUB88A / LDSUB10A

ENGLISHDEUTSCHFRANCAIS

You‘ve made the right choice!

We have designed this product to operate reliably over many years. LD Systems stands for this with its name and many years of experience as a manufacturer of high-quality audio products.

Please read this User‘s Manual carefully, so that you can begin making optimum use of your LD Systems product quickly.

You can ﬁnd more information about LD SYSTEMS at our Internet site WWW.LD-SYSTEMS.COM

Introduction

The LD Systems SATG2 Series consists of ultracompact speakers that are suitable for smaller installations and unobtrusive integration in practically any surroundings, e.g., in bars and restaurants, retail shops or even at

ESPAÑOLPOLSKIITALIANO

home.

Four different passive 2-way speakers in various sizes and an active variant are available in black or white cabinets. The series is rounded out by one passive and two active subwoofers.

FRANCAISFRANCAIS

LD SATG²/SUB SERIES

PASSIVE INSTALLATION SPEAKER: LDSAT42G2(W) / LDSAT242G2(W) /

LDSAT62G2(W) / LDSAT82G2(W) / LDSUB88 POWERED INSTALLATION SPEAKER: LDSAT62AG2(W) / LDSUB88A / LDSUB10A

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

POLSKI

ITALIANO

PREVENTIVE MEASURES:

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.

5. Use the equipment only in the intended manner and for the intended purpose.

ENGLISHDEUTSCHFRANCAIS

6. Use only sufﬁciently stable and compatible stands and/or mounts (for ﬁxed installations). Make certain that wall mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.

7. During installation, observ e the applicable safety regulations for your country.

8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment is always installed so that is cooled sufﬁciently and cannot overheat.

9. Never place sources of ignition, e.g., burning candles, on the equipment.

10. Ventilation slits must not be blocked.

11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment in this case, observe the special instructions noted below. Do not expose this equipment to ﬂammable materials, ﬂuids or gases.

12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers ﬁlled with liquids, such as vases or drinking vessels, on the equipment.

13. Make certain that objects cannot fall into the device.

14. Use this equipment only with the accessories recommended and intended by the manufacturer.

15. Do not open or modify this equipment.

16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.

17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.

18. If your equipment is no longer functioning properly, if ﬂuids or objects have gotten inside the equipment or if it has been damaged in anot her way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualiﬁed personnel.

19. Clean the equipment using a dry cloth.

ESPAÑOLPOLSKIITALIANO

20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.

21. Plastic bags must be kept out of reach of children.

FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:

22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.

FRANCAISFRANCAIS

23. If the equipment has been exposed to strong ﬂuctuations in temperature (for example, after transport), do not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.

24. Before connecting the equipment to the power outlet, ﬁrst verify that the mains voltage and frequency match the values speciﬁed on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not ﬁt in your wall outlet, contact your electrician.

25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the mains outlet and/or power adapter and the equipment connector.

26. When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want

SAFETY:

to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.

27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of the equipment.

28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an authorised service centre.

29. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet.

30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be removed. However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be careful when laying cables.

31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

Never remove the cover, because otherwise there may be a risk of electric shock. There are no user serviceable parts inside. Have repairs carried out only by qualiﬁed service personnel.

The lightning ﬂash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of electrical shock.

The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions.

FRANCAIS

ENGLISHENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

CAUTION – HIGH VOLUME LEVELS WITH AUDIO PRODUCTS!

This equipment is intended for professional use. Therefore, commercial use of this equipment is subject to the respectively applicable national accident prevention rules and regulations. As a manufacturer, Adam Hall is obligated to notify you formally about the existence of potential health risks. Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing high sound-pressure levels (SPL) that can lead to irreversible hearing damage in performers, employees, and audience members. For this reason, avoid prolonged exposure to volumes in excess of 90 dB.

CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS

1. Do not look into the beam from a distance of less than 40 cm.

2. Do not stare into the beam for extended periods at short-to-medium distances.

3. Do not view the beam directly with optical instruments such as magniﬁers.

4. Under some circumstances, stroboscopic effects may trigger epileptic seizures in sensitive individuals! For this reason, persons who suffer from epilepsy should always avoid places where strobe lights are used.

POLSKI

ITALIANO

OPERATING INSTRUCTIONS:

PASSIVE SPEAKERS

SAT42G2(W) and SAT62G2(W) Up to four SAT42G2(W) or SAT62G2(W) speakers per power ampliﬁer output can be operated in parallel at 4

ENGLISHDEUTSCHFRANCAIS

ohms. The speaker signal is simply looped through to the next speaker via the connector panel on the rear.

SAT242G2(W) and SAT82G2(W)

Up to two SAT42G2(W) or SAT62G2(W) speakers per power ampliﬁer output can be operated in parallel at 4 ohms. The speaker signal is simply looped through to the next speaker via the connector panel on the rear.

SUB88 in conjunction with SAT42G2(W), SAT62G2(W), SAT242G2(W) or SAT82G2(W)

Connect the speaker cables from the power ampliﬁer (Output Left and Right) to the Input Left and Right connectors of the subwoofer. Afterwards, connect the SAT Series speakers to the Output Left and Right connectors of the subwoofer. Up to two SAT42G2(W) or SAT62G2(W) speakers per subwoofer output (Output Left and Right) can be operated in parallel at 4 ohms. One SAT242G2(W) or SAT82G2(W) speaker per subwoofer output (Output Left and Right) can be operated in this conﬁguration at 4 ohms. We recommend using speaker cable with a conductor cross-section of at least 2 x 1.5 mm².

ACTIVE SPEAKERS

It is advisable to always turn on active speakers last and turn them off ﬁrst in order to avoid the switch-on noises caused by connected mixers, etc. If multiple active speakers are connected one after the other in series (SAT62AG2), then they should always be switched on in the order in which they are connected and switched off in reverse order.

ESPAÑOLPOLSKIITALIANO

Turn the active speakers off before you connect them. They can be connected both via 6.3 mm TRS plugs (balanced three-pole / unbalanced two-pole) as well as balanced three-pole XLR plugs . Once you have connected all of the necessary cables and set the volume (MAIN LEVEL) of the active speaker to minimum, you can switch on the audio source (e.g., mixer). Afterwards you can also switch on the active speakers. Start an audio signal and now turn the MAIN LEVEL knob clockwise until the desired volume is attained. Carry out these steps with all connected active speakers. On the following pages of this user manual, you will ﬁnd a summary of the connectors, controls, and indicators.

FRANCAISFRANCAIS

OPERATING INSTRUCTIONS :

SUB 10A in conjunction with passive SAT Series speakers

Connect the passive SAT Series speakers to the speaker outputs (SPEAKER OUT LEFT / RIGHT) of the SUB10A.

Up to four SAT42G2(W) or SAT62G2(W) speakers per speaker output can be operated in parallel. The speaker signal is simply looped through to the next speaker via the connector panel on the rear of the passive speaker.

FRANCAIS

ENGLISH

Up to two SAT242G2(W) or SAT862G2(W) speakers per speaker output can be operated in parallel. The speaker signal is simply looped through to the next speaker via the connector panel on the rear of the passive speaker.

We recommend using speaker cable with a conductor cross-section of at least 2 x 1.5 mm².

SUB10A in conjunction with SAT62AG2(W) active speakers

Connect the active speakers to the line outputs (LINE DIRECT OUTPUT) of the SUB10A.

LOOPING THROUGH THE SIGNAL

With the SAT62AG2(W) active speakers, the audio signal can be looped through to additional systems using a three-pole XLR cable . Accordingly, it is not necessary to connect each device to the audio source individually. Please use high-quality XLR cables for this and ensure that they are connected carefully.

SUB88A

To connect the SUB88A active subwoofer to the SAT62AG2 active speakers, the subwoofer must be connected as the last speaker in the chain, since it only has one line input.

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

POLSKI

ITALIANO

CONNECTORS, CONTROLS, AND INDICATORS:

LDSAT62AG2(W):

(LDSAT62AG2 shown)

ENGLISHDEUTSCHFRANCAIS

ESPAÑOLPOLSKIITALIANO

FRANCAISFRANCAIS

POWER SOCKET

IEC power socket 220V-240V with built-in fuse holder. IMPORTANT INFORMATION: Replace the fuse only with a fuse of the same type and rating. If the fuse blows repeatedly, please contact an authorised service centre.

POWER

On / off switch. Before switching the active speaker on or off, always adjust the volume to zero (MAIN LEVEL all the way to the left).

BALANCED LINE INPUT

Balanced line input (XLR / 6.3 mm TRS combo) for connecting an external audio source (e.g., mixer).

DIRECT OUT

Balanced XLR line output for looping through the input signal.

MAIN LEVEL

Volume control

POWER MODE

Toggles between continuous operation (ON) and auto mode (AUTO). In the AUTO position, the ampliﬁer of the speaker system switches on automatically as soon as a signal is received. If there is no signal for several minutes, the ampliﬁer switches to standy mode.

POWER LED

The LED lights up red if the unit is switched on and is in AUTO mode, but no signal is present. Once a signal is present, the LED changes colours to green. The LED also lights up green if the unit is switched on and is in ON mode.

CONNECTORS, CONTROLS, AND INDICATORS:

4 4

5 5

LDSUB10A:

MAIN LEVEL

Overall volume of the system (subwoofer and connected passive speakers).

SUB PHASE

Phase reverse switch for the subwoofer (0°/180°).

SUB LEVEL

Sets the relative volume of subwoofers and satellite speakers.

LINE DIRECT OUTPUT (LEFT / RIGHT)

Balanced XLR line output (left / right) for looping through the input signal.

LINE INPUT XLR (LEFT / RIGHT)

Balanced line input (XLR / 6.3 mm TRS combo, left / right) for connecting an external audio source (e.g., mixer).

SPEAKER OUT (LEFT / RIGHT)

Terminal posts for speaker cables. Connection of speakers or speaker systems with a total impedance of at least 4 ohms per channel. Connect the positive pole (+) of the speaker cable to the red terminal clamp (+) and the negative pole (-) of the speaker cable to the black terminal clamp (-) of the respective channel. Optionally, speaker cables with banana plugs can also be used.

POWER SOCKET

POWER

On / off switch. Before switching the active speaker on or off, always adjust the volume to zero (MAIN LEVEL all the way to the left).

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

POLSKI

ITALIANO

CONNECTORS, CONTROLS, AND INDICATORS:

ENGLISHDEUTSCHFRANCAIS

ESPAÑOLPOLSKIITALIANO

FRANCAISFRANCAIS

CONNECTORS, CONTROLS, AND INDICATORS:

LDSUB88A:

POWER SOCKET

POWER

On / off switch. Before switching the active speaker on or off, always adjust the volume to zero (SUB LEVEL all the way to the left).

BALANCED LINE INPUT

Balanced line input (XLR / 6.3 mm TRS combo) for connecting an external audio source (e.g., mixer).

SUB LEVEL

Volume control

SUB CROSSOVER

Variable low-pass ﬁlter 70 - 140 Hz. Controls the lower limit frequency of the subwoofer.

SUB PHASE

Phase reverse switch for the subwoofer (0°, 180°).

POWER LED

Lights up when the subwoofer is switched on and properly connected to the power mains.

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

SIGNAL LED

The LED lights up when an audio signal is present at the line input.

LIMIT LED

Lights up if the speaker is operating in the clipping range. Brief ﬂashing is not a cause for concern, since the internal audio limiter compensates for over-modulation. Permanent illumination should be avoided by reducing the input level.

POLSKI

ITALIANO

CONNECTORS, CONTROLS, AND INDICATORS:

LDSATG2 PASSIVE SPEAKER:

(LDSAT42G2W shown)

ENGLISHDEUTSCHFRANCAIS

ESPAÑOLPOLSKIITALIANO

TERMINAL CLAMPS FOR SPEAKER CABLES

Connect the positive pole (+) of the speaker cable coming from the ampliﬁer to the red terminal clamp (+) and the negative pole (-) of the speaker cable coming from the ampliﬁer to the black terminal clamp (-).

LDSUB88 PASSIVE SUBWOOFER:

SUB88 IN (IN LEFT shown)

Terminal clamps for speaker cables. Connect the positive pole (OUTPUT LEFT +) of the speaker cable coming from the ampliﬁer to the red terminal clamp (IN LEFT +) and the negative pole (OUTPUT LEFT -) of the speaker cable coming from the ampliﬁer to the black terminal clamp (IN LEFT -) of the subwoofer. Connect the SUB88 IN RIGHT and the ampliﬁer OUTPUT RIGHT in the same manner.

FRANCAISFRANCAIS

SUB88 SAT OUT (SAT OUT LEFT shown)

Terminal clamps for speaker cables. Connect the positive pole (+) of the speaker cable to the red terminal clamp (SAT OUT LEFT +) and the negative pole (-) of the speaker cable to the black terminal clamp (SAT OUT LEFT -) of the respective channel. Connect the SATG2 Series speakers to the other side of the speaker cable in the same manner. IMPORTANT: Observe the remarks rearding the LDSUB88 subwoofer and the passive LDSATG2 Series speakers in the "OPERATING INSTRUCTIONS" section of this user manual!

SPEAKER MOUNT INCLUDED:CONNECTORS, CONTROLS, AND INDICATORS:

FRANCAIS

ENGLISH

WALL BRACKET

M6 BOLT

U-SHAPED MOUNTING BRACKET

WASHER

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

RUBBER WASHER

M6 SOCKET SCREW x 16

SPRING WASHER

WASHER

POLSKI

M6 WINGNUT

NOTE: Speaker brackets for wall mounting are included with all SATG2 Series speakers. With the LDSAT242G2(W) speaker, a bracket for horizontal mounting is included in addition to the bracket for vertical mounting.

ITALIANO

COMBINATION EXAMPLES:

1 X LDSUB10A + 2 X 4 LDSAT42G2(W)

ENGLISHDEUTSCHFRANCAIS

ESPAÑOLPOLSKIITALIANO

FRANCAISFRANCAIS

SPEAKER OUT LEFT SPEAKER OUT RIGHT

COMBINATION EXAMPLES:COMBINATION EXAMPLES:

1 X LDSUB10A + 2 X 2 LDSAT242G2(W)

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

SPEAKER OUT LEFT SPEAKER OUT RIGHT

POLSKI

ITALIANO

COMBINATION EXAMPLES:

1 X LDDJ500 + 1X LDSUB88 + 2 X 2 LDSAT62G2(W) )

ENGLISHDEUTSCHFRANCAIS

SAT OUT LEFT SAT OUT RIGHT

ESPAÑOLPOLSKIITALIANO

FRANCAISFRANCAIS

SUB88 IN LEFT SUB88 IN RIGHT

SPEAKER OUT LEFT SPEAKER OUT RIGHT

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

SUWMB10B (BLACK) SUWMB10W (WHITE)

Universal speaker wall bracket with safety rope. Four snap-lock joints permit mounting of the speaker in virtually any position. Maximum load: 10 kg

POLSKI

ITALIANO

SPECIFICATIONS:

LDSAT42G2(W)

Product type Installation Speakers

ENGLISHDEUTSCHFRANCAIS

ESPAÑOLPOLSKIITALIANO

Type: passive Woofer size: 4 " Woofer size: 101 mm Woofer magnet: ferrite Woofer brand: custom made HF driver size: 1 " HF driver size: 25 mm HF driver magnet: ferrite HF driver brand: custom made Dispersion angle (H x V): 60 x 60 ° Power output (RMS): 60 W Power output (peak): 240 W Frequency response: 75 Hz - 20,000 Hz Sound-pressure level (1 W/1 m): 85 dB Max SPL: 103 dB Impedance: 16 ohms Protection: HF driver Speaker inputs: 1 Speaker input connections: Clamp connector Cabinet material: 12 mm MDF Cabinet surface: textured coating Cabinet colour: black (LDSAT42G2) / white (LDSAT42G2W) Cabinet type: closed Dimensions (W x H x D): 140 x 230 x 125 mm Weight: 5 kg / pair Other features: Wall bracket included

FRANCAISFRANCAIS

SPECIFICATIONS:

LDSAT242G2(W)

Product type: Installation Speakers Type: passive Woofer size: 2 x 4" Woofer size: 2 x 101 mm Woofer magnet: ferrite Woofer brand: custom made HF driver size: 1 " HF driver size: 25 mm HF driver magnet: ferrite HF driver brand: custom made Dispersion angle (H x V): 60 x 60 ° Power output (RMS): 100 W Power output (peak): 400 W Frequency response: 75 Hz - 20,000 Hz Sound-pressure level (1 W/1 m): 88 dB Max SPL: 108 dB Impedance: 8 ohms Protection: HF driver Speaker inputs: 1 Speaker input connections: Clamp connector Cabinet material: 12 mm MDF Cabinet surface: textured coating Cabinet colour: black (LDSAT242G2) / white (LDSAT242G2W) Cabinet type: closed Dimensions (W x H x D): 140 x 378 x 135 mm Weight: 4.15 kg Other features: Wall bracket included

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

POLSKI

ITALIANO

SPECIFICATIONS:

LDSAT62G2(W)

Product type: Installation Speakers

ENGLISHDEUTSCHFRANCAIS

ESPAÑOLPOLSKIITALIANO

Type: passive Woofer size: 6,5 " Woofer size: 165 mm Woofer magnet: ferrite Woofer brand: custom made HF driver size: 1 " HF driver size: 25 mm HF driver magnet: ferrite HF driver brand: custom made Dispersion angle (H x V): 60 x 60 ° Power output (RMS): 80 W Power output (peak): 320 W Frequency response: 55 Hz - 20,000 Hz Sound-pressure level (1 W/1 m): 89 dB Max SPL: 108 dB Impedance: 16 ohms Protection: HF driver Speaker inputs: 1 Speaker input connections: Clamp connector Cabinet material: 12 mm MDF Cabinet surface: textured coating Cabinet colour: black (LDSAT62G2) / white (LDSAT62G2W) Cabinet type: bass reﬂex Dimensions (W x H x D): 200 x 320 x 200 mm Weight: 8.2 kg / pair Other features: Wall bracket included

FRANCAISFRANCAIS

SPECIFICATIONS:

LDSAT82G2(W)

Product type: Installation Speakers Type: passive Woofer size: 8 " Woofer size: 203 mm Woofer magnet: ferrite Woofer brand: custom made HF driver size: 1 " HF driver size: 25 mm HF driver magnet: ferrite HF driver brand: custom made Dispersion angle (H x V): 60 x 60 ° Power output (RMS): 120 W Power output (peak): 480 W Frequency response: 50 Hz - 20,000 Hz Sound-pressure level (1 W/1 m): 93 dB Max SPL: 114 dB Impedance: 8 ohms Protection: HF driver Speaker inputs: 1 Speaker input connections: Clamp connector Cabinet material: 15 mm MDF Cabinet surface: textured coating Cabinet colour: black (LDSAT82G2) / white (LDSAT82G2W) Cabinet type: bass reﬂex Dimensions (W x H x D): 274 x 410 x 243 mm Weight 7 kg Other features: Wall bracket included

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

POLSKI

ITALIANO

SPECIFICATIONS:

LDSUB88

Product type: Installation Subwoofers

ENGLISHDEUTSCHFRANCAIS

ESPAÑOLPOLSKIITALIANO

Type: passive Woofer size: 2 x 8" Woofer size: 2 x 203 mm Woofer magnet: ferrite Woofer brand: custom made Power output (RMS): 200 (2x100)W Power output (peak): 800 (2x400)W Frequency response: 40 Hz - 120 Hz Sound-pressure level (1 W/1 m): 92 dB Max SPL: 115 dB Impedance: 2 x 8 ohms Speaker inputs: 2 Speaker input connections: Clamp connector Speaker outputs: 2 Speaker output connections: Clamp connector Cabinet material: 15 mm MDF Cabinet surface: textured coating Cabinet colour: black Cabinet type: band pass Dimensions (W x H x D): 600 x 250 x 350 mm Weight: 13.3 kg Other features: internal low-pass ﬁlter (120 Hz)

FRANCAISFRANCAIS

SPECIFICATIONS:

LDSAT62AG2(W)

Product type: Installation Speakers Type: active Woofer size: 6,5 " Woofer size: 165 mm Woofer magnet: ferrite Woofer brand: custom made HF driver size: 1 " HF driver size: 25 mm HF driver magnet: ferrite HF driver brand: custom made Ampliﬁer: Class A/B Dispersion angle (H x V): 60 x 60 ° Power output (RMS): 50 W Frequency response: 55 Hz - 20,000 Hz Max SPL: 108 dB Protection: HF driver, overcurrent Controls: Power switch (on/off), volume control, switchable auto-power

mode Indicators: Power Line input connectors: XLR, 6.3 mm TRS (combo) Line output connectors: XLR Power supply: transformer Operating voltage: 220 V AC - 240 V AC, 50 - 60 Hz Power consumption (max.) 80 VA Cabinet material: 12 mm MDF Cabinet surface: textured coating Cabinet colour: black (LDSAT62AG2) / white (LDSAT62AG2W) Cabinet type: bass reﬂex

Dimensions (W x H x D): 200 x 320 x 200 mm Weight: 5.25 kg Other features: Wall bracket included

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

POLSKI

ITALIANO

SPECIFICATIONS:

LDSUB88A

Product type: Installation Subwoofers

ENGLISHDEUTSCHFRANCAIS

ESPAÑOLPOLSKIITALIANO

Type: active Woofer size: 2 x 8" Woofer size: 2 x 203 mm Woofer magnet: ferrite Woofer brand: custom made Ampliﬁer: Class A/B Power output (RMS): 150 W Frequency response: 40 Hz - 120 Hz Sound-pressure level (1 W/1 m): 92 dB Max SPL: 115 dB Protection: overload Controls: Phase 180°, volume, low-pass ﬁlter (70 - 140 Hz) Indicators: Limit, Signal, Power Line inputs: 1 Line input connectors: XLR, 6.3 mm TRS (combo) Power supply: transformer Operating voltage: 220 V AC - 240 V AC, 50 - 60 Hz Power consumption (max.): 200 VA Cabinet material: 15 mm MDF Cabinet surface: textured coating Cabinet colour: black Cabinet type: band pass

Dimensions (W x H x D): 600 x 250 x 350 mm Weight: 15 kg

FRANCAISFRANCAIS

SPECIFICATIONS:

LDSUB10A

Product type: PA subwoofer Type: active Woofer size: 10 " Woofer size: 254 mm Woofer magnet: ferrite Woofer brand: custom made Woofer voice coil: 2 " Woofer voice coil: 50.8 mm Ampliﬁer: Class A/B Power output (RMS): 360 (3x120)W Power output (peak): 1440 (3x480)W Subwoofer frequency range: 40 Hz - 120 Hz Max. SPL (continuous): 118 dB Protection: overcurrent, limiter, short-circuit Input sensitivity: 0.3 V RMS Controls: Subwoofer volume, power switch (on/off), volume, subwoofer

phase reverse Indicators: Power Line inputs: 2 Line input connectors: 6.3 mm TRS, XLR Line outputs: 2 x Direct Output Line output connectors: XLR Speaker outputs: 2 Speaker output connections: Terminal posts Power supply: transformer Operating voltage: 220 V AC - 240 V AC, 50 - 60 Hz Power consumption (max.): 600 VA Cabinet material: 15 mm MDF Cabinet surface: textured coating Cabinet type: bass reﬂex Dimensions (W x H x D): 505 x 345 x 425 mm Weight: 21 kg Other features: M20 threaded ﬂange, ergonomic recessed handles, speaker

outputs with high-pass ﬁlter (170 Hz, -18 dB)

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

POLSKI

ITALIANO

MANUFACTURER´S DECLARATIONS:

MANUFACTURER‘S WARRANTY

This warranty covers the Adam Hall, LD Systems, Defender, Palmer, and Cameo brands. It applies to all products distributed by Adam Hall.

ENGLISHDEUTSCHFRANCAIS

This warranty declaration does not affect the statutory warranty claims against the manufacturer, but expands them with additional warranty claims vis-a-vis Adam Hall.

Adam Hall warrants that the Adam Hall product that you have purchased from Adam Hall or from an Adam Hall authorized reseller is free from defects in materials or workmanship under normal use for a period of 2 or 5 years (please inquire on a product-by-product basis) from the date of purchase.

The warranty period begins on the date on which the product was purchased, proof of which must be produced (through presentation of the invoice or the delivery note with the date of purchase) in the event of a warranty claim. Should products of the brands named above be in need of repair within the limited warranty period, you are entitled to warranty service according to the terms and conditions stated here.

During the Limited Warranty Period, Adam Hall will repair or replace the defective component parts or the product. In the event of repair or replacement during the Limited Warranty Period, the replaced original parts and/or products become property of Adam Hall.

In the unlikely event that the product which you purchased has a recurring failure, Adam Hall has the right, at its discretion, to replace the defective product with another product, provided that the new product is at least equivalent to the product being replaced with regard to the technical speciﬁcations.

Adam Hall does not warrant that the operation of this product will be uninterrupted or error-free. Adam Hall is not responsible for damage that occurs as a result of your failure to follow the instructions included with the Adam Hall branded product. The manufacturer‘s warranty does not cover – expendable parts (e. g., rechargeable batteries)

ESPAÑOLPOLSKIITALIANO

- products from which the serial number has been removed or with a serial number that has been damaged as a result of an accident - damage due to improper use, user error or other external reasons

- damage to devices operated outside the usage parameters stated in the documentation included with the product

- damage due to the use of replacement parts not manufactured, sold or recommended by Adam Hall,

- damage due to modiﬁcation or servicing by anyone other than Adam Hall. These terms and conditions constitute the complete and exclusive warranty agreement between you and Adam Hall regarding the Adam Hall branded product you have purchased.

FRANCAISFRANCAIS

MANUFACTURER´S DECLARATIONS:

LIMITATION OF LIABILITY

If your Adam Hall branded hardware product fails to work as warranted above, your sole and exclusive remedy shall be repair or replacement. Adam Halls’ maximum liability under this limited warranty is expressly limited to the lesser of the price you have paid for the product or the cost of repair or replacement of any components that malfunction under conditions of normal use.

Adam Hall is not liable for any damages caused by the product or the failure of the product, including any lost proﬁts or savings or special, incidental, or consequential damages. Adam Hall is not liable for any claim made by a third party or made by you for a third party.

This limitation of liability applies whether damages are sought, or claims are made, under this Limited Warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim, and cannot be rescinded or changed by anyone. This limitation of liability will be effective even if you have advised Adam Hall or an authorized representative of Adam Hall of the possibility of any such damages, but not, however, in the event of claims for damages in connection with personal injuries.

This manufacturer‘s warranty grants you speciﬁc rights; depending on jurisdiction (nation or state), you may be be entitled to additional claims. You are advised to consult applicable state or national laws for a full determination of your rights.

REQUESTING WARRANTY SERVICE

To request warranty service for the product, contact Adam Hall or the Adam Hall authorized reseller from which you purchased the product.

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

EC DECLARATION OF CONFORMITY

The equipment marketed by Adam Hall complies (where applicable) with the essential requirements and other relevant speciﬁcations of Directives 1999/5/EC (R&TTE), 2004/108/EC (EMC) und 2006/95/EC (LVD). Additional information can be found at www.adamhall.com.

POLSKI

ITALIANO

MANUFACTURER´S DECLARATIONS:

PROPER DISPOSAL OF THIS PRODUCT

(Valid in the European Union and other European countries with waste separation)

This symbol on the product, or the documents accompanying the product, indicates that this appliance may not

ENGLISHDEUTSCHFRANCAIS

be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity.

Household users should contact either the retailer where they purchased this product, or their local government ofﬁce, for details on where and how they can recycle this item in an environmentally friendly manner. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal .

ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION

Energy conservation is an active contribution to environmental protection. Please turn off all unneeded electrical devices. To prevent unneeded devices from consuming power in standby mode, disconnect the mains plug.

ESPAÑOLPOLSKIITALIANO

FRANCAISFRANCAIS

Adam Hall GmbH, all rights reserved. The technical data and the functional product characteristics can be subject to modiﬁcations. The photocopying, the translation, and all other forms of copying of fragments or of the integrlity of this user’s manual is prohibited.

FRANCAIS

ENGLISH

DEUTSCH FRANCAIS

FRANCAIS

ESPAÑOL

POLSKI

ITALIANO

ENGLISHDEUTSCHFRANCAIS

Sie haben die richtige Wahl getroffen!

Diese LD Systems Produkte werden Sie lange Jahre durch Zuverlässigkeit, Wirtschaftlichkeit und einfaches Handling überzeugen. Dafür garantiert LD Systems mit seinem Namen und seiner in vielen Jahren erworbenen Kompetenz als Hersteller hochwertiger Geräte.

Nehmen Sie sich nun ein paar Minuten Zeit, diese Anleitung zu lesen. Wir möchten, dass Sie einfach und schnell in den Genuss dieser Technik kommen.

Mehr Informationen zu LD SYSTEMS ﬁnden Sie auf unserer Internetseite WWW.LD-SYSTEMS.COM

Einführung

Die LD Systems SATG2-Serie besteht aus kompakten Lautsprechern, die sich für kleinere Installationen und dezente Integration in praktisch jedes Ambiente eignen, z.B. in der Gastronomie, im Einzelhandel, aber auch zu

ESPAÑOLPOLSKIITALIANO

Hause.

Vier verschiedene passive 2-Wege Lautsprecher in unterschiedlicher Größe und eine aktive Variante sind in wahlweise schwarzem oder weißem Gehäuse erhältlich. Abgerundet wird die Serie durch einen passiven und zwei aktive Subwoofer.

FRANCAISFRANCAIS

+ 142 hidden pages

LD Systems LDSAT42G2W User Manual [en, de, fr, es, pl, it]

Specifications and Main Features

Frequently Asked Questions

User Manual