La-Z-Boy Reclining Chair User Manual [en, es, fr]

operating instructions

__________

instrucciones de operación

__________

instructions

la-z-boy.com

La-Z-Boy Incorporated

12 84 N. Telegraph Road

Monroe, MI 48162

93000287-00 Rev. 05/13

Congratulations!

Table of Contents

You are now the proud owner of

state-of-the-art Furniture by La-Z-Boy

You have just selected one of the

finest quality upholstered products

produced in the furniture industry,

backed by over 80 years of quality

manufacturing experience.

La-Z-Boy is proud of our designs

and craftsmanship and knows you

Important Safety Instructions....................................4-5

Reclining Chair Assembly Instructions .......................6-9

Rocking Loveseat Assembly Instructions..................10 - 11

Reclining Tension Adjustment Instructions...............12-13

3-Position Legrest Operating Instructions....................14

Reclina-Glider

Swivel Glider Instructions ...........................................1 5

Furniture Placement Guide.........................................16

Cup Holder Cleaning Instructions................................17

Swivel Recliner & Complements

will feel the same as you enjoy your

new furniture’s comfort and style.

IMPORTANT

Read these instructions thoroughly

before using your La-Z-Boy

Keep them for future reference.

furniture.

325

Important Safety Instructions

Important: Read these instructions thoroughly before using.

Important Safety Instructions

Important: Read these instructions thoroughly before using.

DANGER

• To prevent suffocation, keep plastic bags away from children.

WARNING

• Always keep open flame and lit cigarettes away from upholstered furniture. Upholstered furniture may burn rapidly with toxic gas and thick smoke.

• Closely supervise children and disabled persons using this product.

• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back of the unit. Move the unit into or out of the reclining position slowly, making sure that no children or pets are in close proximity.

• This product has many moving parts, serious injury can occur if not used properly. Keep hands, fingers and body parts away from the mechanism. To reduce the risk of head entrapment and other injuries, keep children and pets away from the openings and moving parts in and around furniture.

• Only the occupant should operate the unit. Never attempt to open the legrest by pulling on it.

• Do not stand, sit, or place extra weight on the arms, back or open legrest.

• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.

• Do not use this product if it is damaged. Do not use attachments or substitute parts.

• This product is intended for indoor residential use only.

• Provide a clear path for operation of the chair, back and legrest. Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or interference.

• This product is not intended for use as a health care device.

• Do not operate the unit until the back is installed and locked.

• Use care when moving the product. Before lifting the product, secure the mechanism to prevent unexpected opening or movement. Never move the product by the mechanism, legrest, handle, reclining back, or swivel base. Disconnect modular units. Securely grip non-moving parts only.

• This unit is equipped with a tension adjustment feature for the reclining mechanism that is preset at the factory. The tension setting can be changed for your personal preference. To avoid tip over and insure stability, do not operate the unit with the tension adjustment wing nuts completely loosened (See Reclining Tension Adjustment Instructions).

• Do not place containers with hot beverages in the cup holders. The furniture has motion and beverages may spill and injure the occupant. Do not place oversized or uncovered beverage containers in the cup holders.

– To reduce the risk of serious injury or death:

– To reduce the risk of burns, fire or serious injury:

WARNING

• Do not use La-Z-Boy vehicle is in motion. This furniture is not intended to protect its occupant in an accident. Safely secure the furniture while the vehicle is in motion to prevent injury or damages from any sudden stop.

• If you give this product to someone else, include this Operating Instructions manual.

– To reduce the risk of burns, fire or serious injury:

furniture in a recreational vehicle (or other moving vehicle) while the

NOTICE: – To reduce the risk of product damage:

• Damage will occur to the mechanism if the legrest is forced closed from the 1st or 2nd position. The legrest must be extended to the 3rd position and then closed.

• Do not move the units while connected together. The purpose of the bracket system is to connect the units and prevent them from being separated while on the floor. The bracket system does not provide adequate structural support for the movement of connected units.

• Some units contain cup holders. Take care to prevent spilling of beverages, which could result in damage to cover.

Save These Instructions Save These Instructions

Reclining Chair Assembly Instructions

The Assembly Instructions below are for chair backs having upholstery cover attached to all sides of the back frame. Refer to the instructions on the following pages if your chair back has

loose upholstery cover with fastening tape.

Reclining Chair Assembly Instructions

FIGURE 1

WARNING

• Do not operate the unit until the back is installed and locked.

Install the chair back

1. Lay the back across the arms of the body. Lift the back at a slight angle and align the brackets on the back with the brackets on the body (F

2. Lower the back onto the body, making sure the back and body brackets are completely engaged.

• To make sure the back is properly installed with both sets of back and body brackets engaged, stand behind the chair and twist the back from side to side. If one or both sides move out of position the brackets are not engaged (F

• If you are unable to install the back properly contact your La-Z-Boy dealer for assistance.

3. Lock the brackets by using a screwdriver to push down the locking levers (F

– To reduce the risk of injury:

GURE

1).

IGURE 2). Remove the back and repeat the steps above.

IGURE 3).

Body Bracket

Back Bracket

FIGURE 2

Back and body brackets on this side are not engaged. Remove the back and reinstall.

IGURE 3

Back

Bracket

Locking Lever

Locked Position

Reclining Chair Assembly Instructions

The Assembly Instructions below are for chair backs having a loose upholstery cover with fastening tape. Refer to the instructions on the previous pages if your chair back has upholstery

cover attached to all sides of the back frame.

WARNING

• Do not operate the unit until the back is installed and locked.

Install the chair back

1. Lay the back across the arms of the body. Lift the back at a slight angle and align the brackets on the back with the brackets on the body (F

• The back brackets may be located on the outside or inside of the back assembly.

2. Lower the back onto the body, making sure the back and body brackets are completely engaged.

• For chairs with back brackets on the outside of the back assembly, stand behind the unit and twist the back from side to side. If one or both sides move out of position the brackets are not engaged (F

• For chairs with back brackets on the inside of the back assembly, lift the back upholstery cover to visually confirm that both sets of back and body brackets are engaged (F

• If you are unable to install the back properly contact your La-Z-Boy for assistance.

3. Lock the brackets by using a screwdriver to push down the locking levers (F

CAUTION

• Once the back is installed, the outside back upholstery cover must be secured in place at all times.

– To reduce the risk of injury:

IGURE 2). Remove the back and repeat the steps above.

IGURE 3).

– To reduce the risk of minor injury:

IGURE 1).

dealer

IGURE 4).

FIGURE 1

Body Bracket

Back Bracket

IGURE 3

FIGURE 2

Back and body brackets on this side are not engaged. Remove the back and reinstall.

FIGURE 4

Back

Bracket

Locking Lever

Locked Position

4. The outside back upholstery cover attaches to the body in different locations, depending on the style.

• Pull the outside back upholstery cover down tight and press the fastening tape on the back upholstery cover to the fastening tape on the body (F

• Pull the outside back upholstery cover down tight and press the fastening tape on the back upholstery cover to the fastening tape on the lower seat frame. Tuck the sides in and loop the elastic strap behind the lower seat frame (F

IGURE 5).

IGURE 6).

FIGURE 5

Fastening Tape

FIGURE 6

Elastic Strap

Fastening Tape

Rocking Loveseat Assembly Instructions Rocking Loveseat Assembly Instructions

WARNING

• Provide a clear path for operation of the back and legrest. Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or interference.

1. Place the furniture in the desired location; refer to Furniture Placement Guide.

2. Use a T-30 torx driver to loosen the threaded studs to approximately 1"; this measurement may vary depending on the fabric and style. The threaded studs are located on the left side (sitting) of right side (sitting) units.

3. Place the console (F Position the console (with the threaded studs) slightly behind the recliner. Separate the fronts of the units to be connected, about 6" apart. Pull the console forward until the threaded stud on the console engages in the rear bracket on the recliner.

WARNING

• The front of the unit must be raised to engage the front bracket. Please seek assistance if you are unable to lift at least 21 pounds.

• Keep feet clear of the unit when lowering into position.

4. Lift the front of the console approximately 3" off the ground, aligning it to the attachment bracket on the left side (sitting) rocker recliner. Gently lower the threaded stud into the front attachment bracket (F Keep feet clear of the unit when lowering into position.

NOTE: Due to variations in upholstery and style, the threaded stud length may need to be adjusted to fit

into the attachment brackets or control gaps between units. Loosen or tighten the threaded studs to provide adequate clearance.

5. Place the right side (sitting) rocker recliner (F side (sitting) rocker recliner (with the threaded studs) slightly behind the console. Separate the fronts of the units to be connected, about 6" apart. Pull the right side (sitting) recliner forward until the threaded stud on the recliner engages in the rear bracket on the console.

WARNING

• The front of the unit must be raised to engage the front bracket. Please seek assistance if you are unable to lift at least 21 pounds.

• Keep feet clear of the unit when lowering into position.

NOTICE:

• Lift from the side frame. Do not lift from the upholstery or bottom of the legrest.

– To reduce the risk of serious injury:

GURE

3) approximately 2" to the side of the left side (sitting) rocker recliner (FI

– To reduce the risk of serious injury:

IGURE 2) about 2" to the side of the console. Position the right

– To reduce the risk of serious injury:

– To reduce the risk of product damage:

GURE

IGURE 4).

1).

NOTICE:

8. The units must be disconnected before moving the loveseat. To disconnect the units, lift up the left front corner of the right side (sitting) recliner approximately 3" to clear the front attachment bracket on the console. Move the recliner to the side before returning it to the floor. Slide the right side (sitting) recliner backward to disengage the back bracket on the console. Repeat these steps to disconnect the console from the left side (sitting) recliner.

FIGURE 1

Left Side (Sitting) Rocker Recliner

Rear Bracket

Front Attachment Bracket

FIGURE 3

Console

Rear Side Mount Bracket

– To reduce the risk of product damage:

FIGURE 2

Right Side (Sitting) Rocker Recliner

Threaded Studs

FIGURE 4

Front Attachment Bracket (Left Side Sitting Rocker Recliner)

6. Lift the front of the right side (sitting) recliner approximately 3" off the ground, aligning it to the attachment bracket on the console. Gently lower the threaded stud into the front attachment bracket. Keep feet clear of the unit when lowering into position.

7. Adjust the glides on the console to level the unit, if necessary. Turn clockwise to lower and counterclockwise to raise.

Front Side Mount “U” Bracket

Front Attachment Bracket (Console)

Reclining Tension Adjustment Instructions

WARNING

– To reduce the risk of injury:

NOTICE: – To reduce the risk of product damage:

• Make sure the legrest is closed before tilting forward and adjusting the tension.

• Do not completely tighten the wing nuts. The tension springs should not be completely compressed after making adjustments. If this occurs, the wing nuts must be loosened a minimum of ½-turn to avoid damage to the spring tension assembly.

• Do not completely loosen the wing nuts. The spring should not slide on the bolt after making adjustments. If the spring slides on the bolt, tighten the wing nut clockwise a minimum of ½-turn after the spring no longer slides on the bolt.

• Adjust both wing nuts equally.

Adjustment Instructions

You can adjust the tension of the reclining mechanism to respond to your individual size.

1. Reclina-Rocker

Gently tilt the reclining chair forward to rest on its arms and top of the back. Locate the wing nuts, one on each side, toward the back of the recliner under the seat (F

NOTE: The Reclina-Glider

La-Z-Boy Classics

Gently tilt the reclining chair forward to rest on its arms and top of the back. Locate the wing nuts, one on each side, toward the center of the recliner under the seat (F

2. Adjust the tension by turning the wing nuts or thumb wheels in ¼-turn increments until the desired setting is reached.

• A taller or heavier person may choose to increase the reclining tension by tightening the

• A smaller person may choose to decrease the reclining tension by loosening the wing

3. Return the reclining chair to the upright position. Test the new setting. Make additional adjustments if needed following these steps.

Chair, Reclina-Glider®Chair and Reclina-Way®Chair

Swivel Recliner has a thumb wheel (not shown) instead of a wing nut.

Low Profile recliner & High Leg recliner with 3-position mechanism

wing nuts or thumb wheels clockwise.

nuts or thumb wheels counterclockwise.

IGURE 1).

IGURE 2).

FIGURE 1

Reclina-Rocker®, Reclina-Glider®and Reclina-Way

IGURE 2

La-Z-Boy Classics

Wing Nut

Tension Spring

3-Position Legrest Operating Instructions

Reclina-Glider®Swivel Recliner &

Complements Swivel Glider Instructions

WARNING

• Provide a clear path for operation of the back and legrest. Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or interference.

• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.

NOTICE:

• Damage will occur to the mechanism if the legrest is forced closed from the 1st or 2nd position. The legrest must be extended to the 3rd position and then closed.

To Operate the Legrest

1. Your La-Z-Boy comfort. Simply pull on the handle rotating it counterclockwise to control the legrest (F You may stop in any one of three ideal positions. The 1st position is slightly inclined for relaxing reading (F (F

IGURE 3). The 3rd position is fully extended for complete relaxation (FIGU RE 4). To lower the

legrest, rotate the handle counterclockwise to the fully extended position, then rotate clockwise to the fully closed position.

2. The chair back can be reclined with the legrest closed or extended. To recline, apply pressure to the back. Sit upright to return the back to an upright position.

3. Bring the back upright and close the legrest before getting out of the unit.

Feature of the Reclina-Rocker

The chair body can be tilted back when the legrest is in use. Shifting your body weight rearward will cause the chair body to tilt backward offering a number of different positions.

FIGURE 1

Closed Position

chair is equipped with a three-position locking legrest for customized seating

IGURE 2). The 2nd position is slightly more inclined for comfortable television viewing

– To reduce the risk of serious injury:

– To reduce the risk of product damage:

IGURE 2

1st Position

IGURE 1).

To Activate the Swivel Feature

1. Turn the unit on its back.

2. Locate the two spacer bushings, two truss head screws and swivel base bottom (F

3. Remove the two truss head screws using a T-30 torx driver while holding the swivel base bottom steady.

NOTE: The two polyethylene washers are attached with adhesive and do not need to be removed.

4. Remove the two spacer bushings from between the swivel base bottom and glide base subassembly (F

5. Return the chair to the upright position.

6. Store parts for future use to deactivate the swivel feature.

To Deactivate the Swivel Feature

1. Turn the unit on its back.

2. Rotate the Swivel Base Bottom until the holes on the Swivel Base Bottom line up with the holes on the Glide Base Subassembly (F

3. Hold the swivel base bottom steady. Place the spacer bushings between the holes in the Swivel Base Bottom and the Glide Base Subassembly. Insert the truss head screws through the holes in the Swivel Base Bottom, through the spacer bushings and into the holes in the Glide Base Subassembly. Fasten each screw using the T-30 torx driver.

4. Return the chair to the upright position.

FIGURE 1

IGURE 2).

NOTE: Swivel base bottom is shown forward of normal position to clearly show parts.

FIGURE 2

IGURE 1).

IGURE 3

2nd Position

IGURE 4

3rd Position

Swivel Base Bottom

Spacer Bushing Polyethylene

Washer Truss Head

Screw

Swivel Base Bottom

Glide Base Subassembly

Spacer Bushing

Polyethylene Washer

Truss Head Screw

+ 17 hidden pages

La-Z-Boy Reclining Chair User Manual [en, es, fr]

Specifications and Main Features

Frequently Asked Questions

User Manual