LAZBOY LZ6220 Installation Manual

Comfort. It's what we do.

Touch Sensitive Remote Control

Model LZ6220

16 Function Universal Remote Control

With Touch Sensitive Keypad

Installation Guide

TM

ECP will repair or replace the defective parts and return
them at ECP's cost by a shipping method selected by
ECP. When contacting ECP to obtain an RMA,
Purchaser may request expedited return shipping at
Purchaser's cost.

THIS WARRANTY IS NOT TRANSFERABLE, AND,
TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, IS IN LIEU OF ALL OTHER
WARRANTIES, REPRESENTATIONS AND
CONDITIONS, EXPRESS OR IMPLIED,
STATUTORY OR OTHERWISE, INCLUDING BUT
NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. NO OTHER PERSON OR
REPRESENTATIVE IS AUTHORIZED TO MAKE
ANY OTHER WARRANTY ON BEHALF OF ECP OR
ASSUME FOR ECP ANY OTHER LIABILITY IN
CONNECTION WITH THE SALE OF THIS
PRODUCT. IN NO EVENT WILL ECP BE LIABLE
FOR ANY DAMAGES, INCLUDING BUT NOT
LIMITED TO INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF
THE USE OR INABILITY TO USE THE PRODUCT,
INCLUDING DAMAGES DUE TO ECP'S
NEGLIGENCE.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE
AND COUNTRY TO COUNTRY.

©

La-Z-Boy is a Trademark of La-Z-Boy Incorporated and
is used under license to

Elexa Consumer Products, Inc. 2008
6200 N. Hiawatha Ave, 8th Floor Chicago, IL 60646

31

95 x 190mm

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,

including interference that may cause undesired
operation.

Modifications not expressly approved by the
manufacturer could void the user's authority to operated
the equipment under FCC rules.

1

PRODUCT DIAGRAM

2

CBL

CD

AUD AUX

BACK

SOURCE

2

3

4

5

6

7

8

9

10
11

12
13

14
15

16
17

18
19

1

21

22
23

24

25

26

27
28

29

30

31

32

33

34

35

36

3738

20

17. -Fast forward when in VCR mode. Scan
forward when in VCR, DVD, CD & DVR
mode.

18. -Access the play feature when in VCR, DVD,
DVR or CD mode.

19. -Brings up the menu screen.

20. -Brings up the guide screen when in SAT or
cable mode. Access the record function when
in VCR & DVR mode.

21. -Stop Key when in VCR, DVD, CD & DVR
mode.

22. -Pause when in VCR, DVD, CD and DVR
mode.

23. -Exits on screen menu's and guides and returns
you to the previous on screen selection.

24. -Allows you to return to the previously selected
channel in TV, SAT, or CABLE mode.

25. -Picture in Picture. This allows you to access
the picture in picture feature of your TV.

26. -Allows you to turn the volume on or off when
in TV mode.

27. -Allows you to toggle through the return input
source when in TV mode.

28. -Sleep. Allows you to set a timer to turn off the
TV on some TV models equipped with this
feature.

29. -Allows you to program a sequence of steps
such as turn on your TV, turn on your DVD
player, turn on you home theater receiver, and
press play on your DVD player to watch a
movie. All in sequence. Each smart key can
program up to 20 steps. Use shift smart 1. smart

nd

2 or smart 3 to access a 2 tier of smart keys

30. -Changes the channels forward when in TV,
DVR, Satellite or Cable mode.

31. -Changes the channels backward when in TV,
DVR, Satellite or Cable mode.

32. -Increase the volume of the device. Normally
used in TV mode.

33. -Decreases the volume of the device. Normally
used in TV mode.

4

BACK

SOURCE

KEY FUNCTION DESCRIPTIONS

1. -Programs your TV. Also programs one
auxiliary device using the shift key.

2. -Programs your DVD Player. Also programs
one auxiliary device using the shift key.

3. -Programs your satellite receiver. Also
programs one auxiliary device using the shift
key.

4. -Programs your VCR. Also programs one
auxiliary device using the shift key.

5. -Programs your cable device. Also programs
one auxiliary device using the shift key.

6. -Programs your CD device. Also programs one
auxiliary device using the shift key.

7. -Programs your audio receiver. Also programs
one auxiliary device using the shift key.

8. -Programs one auxiliary device. Programs one
additional auxiliary device using the shift key.

nd

9. -Allows you to program a 2 tier of
components into the TV, DVD, SAT, VCR,
CBL, CD, AUD and AUX keys. Can also
allow you to access secondary functions of
certain devices.

10. -Turns devices for remotes current mode on or
off.

11. -Turns TV power on or off once your TV has
been programmed.

12. -Allow you access to the subtitle feature of
your DVD player or closed caption feature of
your SAT or CABLE.

13. -Allows access to the toggle function from PIP
back to normal picture.

14. -Scrolls backward thru chapters when in DVD
mode or tracks when in CD mode.

15. -Scrolls forward thru chapters when in DVD
mode or tracks when in CD mode.

16. -Rewind when in VCR mode. Scan back when
in DVD, CD & DVR mode.

3

AUX

AUD

CD

CBL

34. -Allow access to the OK function when
scrolling thru menus & guides.

35. -Scrolls up thru menus and guides.

36. -Scrolls down thru menus and guides.

37. -Scrolls right thru menus and guides.

38. -Scrolls left thru menus and guides.

5

Congratulations on the purchase of your La-Z-Boy
Universal Remote Control, a state of the art product
which integrates several infra-red devices to deliver
complete A/V control at the tip of your fingers.

Before operating your remote please read through this
manual carefully and save it for future reference.

This package contains the following:

- One LZ6220 Touch Sensitive Remote Control.

- One Installation Guide.

- One Quick Reference Guide.

- One Infra-red Device Code List.
One LZ100 Charging Cradle.

- One Nickel Metal Hydride Battery Pack.

- One Power Adaptor.

- One USB Cable.

La-Z-Boy has evolved throughout their 75 year history
to become America's Number 1 furniture brand.

The new line of La-Z-Boy Universal Remote Controls
represents the perfect marriage of relaxation, comfort,
ease of use, quality and convenience when watching
television in your favorite La-Z-boy!

The La-Z-Boy Difference:

- Bilingual Consumer hotline available 24 hours/day,

7 days/week.

- Easy to follow quick reference guide.

- Comfortable rubber grips.

- Built in find feature Never lose your remote again.

- On-line programming with on-line tutorial.

- Rechargeable batteries.

- Charging cradle/Docking station.

-

6

Table of Contents

Product Diagram/Key Function Descriptions Page 2

Introduction/Package Contents Page 6

Table of Contents Page 7

Getting Started Page 8

Battery Installation & charging cradle
Information Page 9

How to find the Remote Page 11

Keypad Sensitivity level set up Page 12

How to set up your La-z-boy remote Page 13

oBy code entry
oBy code search
oBy Learning
oBy On Line Programming

Maintenance Page 28

Troubleshooting Page 29

Warranty Page 30

7

GETTING STARTED

A few helpful hints on terms used in this manual.

LR: La-Z-Boy Universal Remote Control

Backlighting: The blue backlighting on the touch

sensitive inlay/keypad of your La-z-boy remote.
Backlighting turns on each time a key is pressed and will
turn off 8 seconds after the last key is released.

Battery Low: If the upper 4 red device mode indicators
flash 4 times and turn off after activating any command,
it shows that the battery level is low. You must recharge
the battery pack by placing your remote into the
charging cradle. The upper 4 red device mode indicators
will display in a moving pattern from left to right.

Shift: The shift key allows you to access a second tier
of components with your remote. Please follow the
instructions in this manual. A red LED backlight will
indicate components 1-8. A green LED backlight will

nd

indicate components 9-16 programmed into the 2 tier
with the shift key. (AUX 1-8)

8

1. HOW TO INSTALL BATTERIES

- Take off the battery case cover,
then connect the battery into the
remote unit.

CAUTION ON BATTERY

- Be sure to use only the rechargeable nickel metal­hydride (Ni-MH) battery pack that is supplied with the
remote control.

- When loading, be sure to properly attach the
rechargeable battery cable connector to the remote
control socket.

- Be sure to properly dispose of the rechargeable battery
pack in accordance with the guidelines (regulations)
for your local area.

REPLACING THE BATTERIES

The batteries in the Remote control
are Nickel Metal Hydride (Ni-MH)
batteries. It is advised to change the
batteries when the operation of your
LR becomes unreliable and is
unable to hold a charge.

If you want to order new batteries,
please contact customer service.
(1-888-229-1459)

Warning:

Replace the batteries only with an original LR battery
pack; otherwise the warranty is no longer valid and a
hazardous situation could occur.

9

1

2

1

2

10

1.1. HOW TO CHARGE BATTERIES

When it is first unpacked, the supplied battery pack is not
fully charged. Be sure to fully charge it before usage for a
minimum of 12 hours.

Connect with AC Adapter

Connect the AC adapter to the
charging terminal. The red LED
indicator on the cradle will
illuminate.

Resting on the Cradle

Put the remote unit on the docking
charger. Be sure to align the
contacts properly. The 4 red uppers
device mode keys should be in a
moving pattern from left to right to
indicate the LR is charging.

NOTES:

- When charging the remote control, be sure to
always use the supplied AC adapter.

- Do not try to charge devices other than the
remote control with the supplied AC adapter.
This could damage the AC adapter or the
connected device.

2. KEYPAD SENSITIVITY LEVEL SET
UP

Set up

Keypad sensitivity- Your LR features a touch sensitive
keypad. You can adjust the sensitivity of this keypad by
following the steps below.

Note:
Do not set the sensitivity too high for the keypad or the
keys may respond too easily to mistaken touches.

2.1. Hold down "CHANNEL+" and "VOLUME-"
keys on the remote simultaneously for 2 seconds
until you hear two beep sounds. Upper four device
mode keys (TV, DVD, SAT, VCR) will light up.

2.2. Press "OK" key. One device mode indicator will
flash indicating factory preset sensitivity level ie.
(CBL or level 5). Please refer to the following
chart.

Each device mode indicator light means different keypad
sensibility.

2.3. Press " " key to increase sensitivity.

2.4. Press " " key to decrease sensitivity.

2.5. Press "OK" key to confirm. All device mode keys
will turn off except the selected device mode key
if successful.

Note:

If no key is pressed for more than 8 seconds, the
device mode indicators will flash six times and the
setup sensitivity mode will exit automatically.

12

Indicator

Sensibility

TV

Low

DVD

*

SAT

*

VCR*CBL*CD*AUD*AUX

High

1.2. HOW TO FIND THE REMOTE

- Press find key on the charging cradle. The red LED
indicator will flash 4 times.

- Your LR will emit a continous series of beep tones.

- Press any key on the LR once it is located to turn off
the beep tones. Note, the LR will emit a series of beep
tones for 60 seconds if no key is pressed and then turn
off.

11

Note:

When programming AUX 1-8 devices, the device mode
key backlight will be green.

Suggestion:

- If you cannot find a correct Device Code for your
equipment, refer to the section that follows: How To
Set Up The LR - By Searching Through the Library.

- For future reference it is recommended to make a note
of your Device Codes on the label provided at the
bottom of the charging cradle after setting up your LR
correctly.

3.2. By Searching Through the Library

If you cannot identify a correct Device Code for your
equipment from the Device Code list, you may search
through the code library:-

3.2.1. Turn on your device manually (e.g. TV).

3.2.2. Press a desired Device Mode Key (e.g. TV). The

red device mode key will light up.

3.2.3. Hold down "CHANNEL+" and "VOLUME-" on

the LR together simultaneously for 2 seconds until
the upper 4 red device mode indicators light up
(TV, DVD, SAT, VCR) The lower clear function
keys will also be lit and you will hear 2 beep tones.

3.2.4. Enter a corresponding Search Code from the

following table. The indicator should go out
immediately.

(e.g. press TV device mode key, then press
"CHANNEL+" and "VOLUME-", and enter The TV
Search Code 0001.) All device mode keys will flash
twice and turn off except the selected device if successful.

DEVICE
TYPE:

SEARCH
CODE:

TV

0001

VCR/LASER

DISK

0002

SAT

0003

CABLE

0004

DVD

14

DEVICE
TYPE:

SEARCH
CODE:

0005

AUDIO

0006

CD

0007

HOME

THEATER

0008

3. HOW TO SET UP YOUR LA-Z-BOY
REMOTE (LR)

3.1. By entering Device Code

You may setup your La-Z-Boy Remote (LR) by the
following code entering instructions.

3.1.1. Turn on your device (e.g. TV).

3.1.2. Refer to the LR Infra Red DEVICE CODE LIST;
look up the 4-digit Device Code which
corresponds to the brand of your A/Vequipment. If
there are more than one Device Code listed under
your brand, try from the first code.

3.1.3. Press a desired Device Mode Key (e.g. TV). The
red device mode key will light up.

3.1.4. Hold down "CHANNEL+" and "VOLUME-" on
the LR simultaneously for 2 seconds until the red
upper 4 red device mode indicators light up (TV,
DVD, SAT, VCR) The lower clear function keys
will also be lit and you will hear 2 beep tones.

3.1.5. Use the number keys 0-9 to enter your 4-digit
Device Code. All device mode keys will flash
twice and turn off except the selected device if
successful.

Then try the function keys (e.g. TV) on the LR. If your
device (e.g. TV) responds to your activated function
correctly, you have entered the right Device Code.
Otherwise, repeat the above setup with the next available
Device Code until your device (e.g. TV) responds to
your activated function, and most keys work correctly.

* Simply repeat the above procedures to enter the

Device Codes for your VCR, SAT, DVD and other
Devices. (Remember to press a correct Device
Mode Key in step 2 above). For set up of
Auxiliary devices (AUX 1-8) press "SHIFT"
followed by the desired device key (AUX 1-8)
then follow steps 4-5 above.

13

3.2.5. Press the same desired device mode key again as
in step 2 above. (e.g. TV)

3.2.6. Hold down "CHANNEL+" and "VOLUME-"
together simultaneously again for 2 seconds until
the upper 4 red device mode indicators light up
(TV, DVD, SAT, VCR) The lower clear function
keys will also be lit and you will hear 2 beep tones.

3.2.7. Aim the LR at your device (e.g. TV); press the " "
(power) key repeatedly every 1-2 seconds until the
device has been turned off. The red LED indicator
will blink once each time you press the " " (power)
key to indicate your remote is scrolling thru the
code library. Once your device has been turned off,
immediately press the same device mode key (e.g.
TV) to lock in the search code and the red upper 4
red device mode indicators will flash 3 times and
your programmed device mode key should remain
lit.

* Simply repeat the above setup procedures to search

the Device Code for your VCR, SAT, DVD and other
Devices. (Remember to press a correct Device Mode
Key and correct Search Code in step 3 . 2 . 2 - 3 . 2 . 7
above).

* For set up of Auxiliary devices (AUX 1-8) press

"SHIFT" followed by the desired device key (AUX
1-8) then follow steps 3.2.3-3.2.7 above.

Note:

- When programming AUX 1-8 devices the device
key backlight will be green.

- The search process can take several minutes due to
the number of codes stored in the library.

- You cannot search through the code library for
DVR devices. This code must be entered from the
LR infra red device code list.

15

Important:
During set up mode, the upper 4 red device mode
indicators will blink six times and the set up procedure
will be terminated if any of the following conditions
occur;

- No key has been pressed for more than 8 seconds.

- An invalid code number has been entered.

- An invalid key (not a numeric key) has been pressed.

You can press SMART 1, SMART 2 or SMART 3 to
exit the search mode at any time. The upper 4 red device
mode indicators will flash 6 times to indicate your remote
has exited the search procedure.

Important:

When searching through the Library for some older
devices, if the power on/off function of your device is
not infra-red controlled - you need to follow steps 3.2.2
to 3.2.6 above and start searching:

- Press " " (power) key and another important
function key alternately until your device responds to
the expected function, press the same device mode
key (e.g. TV) to lock in the code.

- Press " " (power) key & "Channel+" alternately, or;

- Press " " (power) key & "1" alternately.

Note:

- Each time you press the " " (power) key, the LR
will skip to the next code and send out a POWER
signal trying to turn off your device.

- If you failed to stop pressing the " " (power) key in
time when your device has been turned off, turn on
your device again immediately. Before the 4 red
upper device mode indicators goes out, press " "
(mute) on the LR to skip backward. Repeat the step 7
above and lock in the code.

- If the 4 upper device mode indicators flash 6 times
after you pressed the " " (power) key, you are
already at the last code of the library.

- Besides device keys, " " (power) key and " "
(mute) key, all keys can be operated if the remote has
entered search mode.

16

4. HOW TO SET UP YOUR LA-Z-BOY
REMOTE (LR)(Learning Commands)

Your LR is equipped with learning capability. This
allows you to "teach" your LR certain function from your
original equipment remote. Please follow the steps
below.

4.1. Press the desired device mode key (e.g. TV).

4.2. Hold down "CHANNEL+" and "VOLUME-"
keys on the remote simultaneously for 2 sec ond s
until the upper 4 red device mode indicators light
up (TV, DVD, SAT, VCR) The lower clear
function keys will also be lit and you will hear 2
beep tones.

4.3. Enter the learning code "0", "0", "0", "0". The
upper 4 red device mode indicators (TV, DVD,
SAT, VCR) flash once and then stay lit
continuously. The LR is now ready to learn
commands.

4.4. Place the LR and your device remote on a flat
surface, aimed at each other 1-3 inches apart.

4.5. Press a desired key on your LR where you want
the learned function from your original equipment
remote to be located

4.6. Press and keep holding the key on your original
equipment remote which you want to learn for a
few seconds.

4.7. When the upper 4 red device mode indicators
flash twice and then stay lit continuously, the
command has been learned successfully and you
can release the key on your original equipment
device remote. If the upper 4 red device mode
indicators flash six times, it shows an error in the
learning process. Adjust the position of both
remotes and repeat from step 4.5 again.

1817

4.8. Repeat from step 4.5 to learn other key functions,
or press the same device mode key on step 4.1 (e.g.
TV) to terminate the learning mode. The upper 4
red device mode indicators will flash twice and
then all device mode indicators turn off except the
selected device mode key.

Note:

- On step 4.5 if no key is selected for more that 8

seconds, the upper 4 red device mode indicators will
flash six times then all device mode indicators turn
off except selected device mode key and the learning
mode will exit automatically.

- On step 4.6, if no other remote signal is received for

more than 8 seconds, the 4 upper red device mode
indicators flash six times and keep on, and you need
to select a desired key again for learning as in step 4 . 5
on your LR.

- Each function key will hold one command only, a new

command to be learned will automatically erase and
replace the previous one.

- If the device mode indicators flash three times during

the transference of signals, the maximum 100
commands memory bank is full, press the same
device key again to resume normal operation.

- Eight device mode keys (TV, DVD, SAT, VCR, CBL,

CD, AUD & AUX), as well as the SHIFT, SMART 1,
SMART 2 and SMART 3 keys cannot be used for
learning functions.

5. HOW TO SET UP YOUR LA-Z-BOY
REMOTE (LR) (Teaching a dual signal)

If you found a learned programmed key only works
occasionally, your device remote may contain dual
signals. Try the following steps to learn this command:

5.1. Follow the steps from 4.1 to 4.4.

5.2. Press a desired key once on your LR which you

want to learn the command.

5.3. Press and keep holding the key on your original

equipment remote which you want to learn for a few
seconds.

5.4. When the upper 4 red device mode indicators flash

twice and then stay lit continuously, the command
has been learned successfully and you can release
the key on your original equipment remote.

5.5. Press the same key on step 5.2 once on the your LR

again.

5.6. Press and keep holding the same key on your device

remote on step 5.3 until the upper 4 red device mode
indicators flash twice and then stay lit continuously.
The dual signal command has been learned
successfully.

5.7. Repeat from step 5.2 to learn another keys dual

signal, or press the same device mode key on step

5.1 (e.g. TV) to terminate the learning mode, the
upper 4 red device mode indicators will flash twice
and then all device mode indicators turn off except
selected device mode key.

Note:

- On step 5.2 or 5.5 if no key is selected for more than 8

seconds, the upper 4 red device mode indicators will
flash six times, then all device mode indicators turn off
except the selected device mode key and the learning
mode will exit automatically.

- On step 5.3 or 5.6, if no IR signal is received for more

than 8 seconds, the upper 4 red device mode indicators
will flash six times and stay lit, and you need to select a
desired key again for learning as in step 5.2 or 5.5.

2019

6. HOW TO SET UP YOUR LA-Z-BOY
REMOTE (LR) (By PC SETUP)

- Press next to

continue.

6.2. Destination confirmation screen

- Press next to

continue.

6.3. Completion and launch screen

- Press finish to

complete the
installation.

- Connect your LR

to your PC via a
USB connection.

- Click "launch LR

online" to
immediately start
up the software.

- Visit www.lazyboyremotes.com .

- Select "support", then "code download".

- Click the LR online image on the screen to download

the software interface.

6.1. A welcome screen will pop up

21

7. OPERATING THE LA-Z-BOY
REMOTE (LR)

Normal Operation

7.1. Once you have setup up the LR for your A/V

equipment, it works like your original remote
controls. To operate, just aim it at your equipment,
press an appropriate device mode key and invoke
the desired function by pressing a corresponding
key on your LR. The keypad will illuminate and
you will hear a beep tone as confirmation of key
touch.

7.2. Use the shift button when attempting to access

additional auxiliary devices or when attempting to
access secondary functions. Please refer to the Key
Function Description.
SHIFT mode will be deactivated after the desired
key is released.

7.3. If your LR is moved the built in touch sensitive

keypad will illuminate.

7.4. The backlit keypad of the LR will be OFF if no key

is pressed and no motion is detected for 8 seconds.

7.5. Your LR controls up to 16 devices. Press each

device key directly to select first 8 (e.g. TV, red
device key indicator will light up). Press SHIFT
key and then device key to select another 8 (from
AUX 1-8, the green device key indicator will light
up).

7.6. To enable / disable the key tones sound, press and

hold "CHANNEL+" and " " keys on the remote
simultaneously for 2 seconds until the device
indicators flashes. If it flashes once, the "beep"
sound is enabled, if it flashes twice, the "beep"
sound is muted.

22

8. PUNCH THROUGH

You can activate certain functions like TV volume to be
operated in other modes such as SAT. This is referred to
as punch through. Please refer to the following
procedure for activating this function.

8.1. To activate the Punch through Channel setting:

8.1.1. Press and hold "CHANNEL+" and "VOLUME-"
keys on the remote simultaneously for 2 seconds
until the upper 4 red device mode indicators light
up (TV, DVD, SAT, VCR) The lower clear
function keys will also be lit and you will hear 2
beep tones.

8.1.2. Enter the punch through code "1", "1", "1", "0".
The upper 4 red device mode indicators (TV, DVD,
SAT, VCR) will flash once and then stay lit
continuously. The lower clear function keys will
also be lit.

8.1.3. Press desired device mode key. (e.g. TV)

8.1.4. Press "CHANNEL+" key.

8.1.5. Press desired channel code device mode key (e.g.
SAT).

8.1.6. The upper 4 red device indicators will flash twice
and setting punch through mode will exit if the
setting is activated.

8.1.7. Example: SAT channel is activated on TV mode.

8.2. To deactivate the Punch through Channel
setting:

8.2.1. Press and hold "CHANNEL+" and "VOLUME-"
keys on the remote simultaneously for 2 seconds
until the upper 4 red device mode indicators light
up (TV, DVD, SAT, VCR) The lower clear
function keys will also be lit and you will hear 2
beep tones.

8.2.2. Enter the punch through code "1", "1", "1", "0".
The upper 4 red device mode indicators (TV, DVD,
SAT, VCR) will light up. The lower clear function
keys will also be lit.

8.2.3. Press desired device mode key. (e.g. TV)

8.2.4. Press "CHANNEL-"

8.2.5. The upper 4 red device mode indicators will flash
twice and setting punch through mode will exit if
the setting is deactivated. The lower clear function
keys will also be lit.

8.2.6. Example: Punch through Channel is deactivated in
TV device mode.

Note:

- If the same device mode key is pressed twice
during the activate process (7.1), the upper 4 red
device mode indicators flash six times, indicating
the punch through mode will exit and the punch
through status will remain unchanged.

- Setting channel in punch through mode will
activate both the "CHANNEL+" and
"CHANNEL-" key.

8.3. To activate the Punch through Volume setting:

8.3.1. Hold down "CHANNEL+" and "VOLUME-"
keys on the remote simultaneously for 2 seconds
until the upper 4 red device mode indicators light
up (TV, DVD, SAT, VCR) The lower clear
function keys will also be lit and you will hear 2
beep tones.

8.3.2. Enter the punch through code "1", "1", "1", "0".
The upper 4 red device mode indicators (TV, DVD,
SAT, VCR) flash once and then stay lit
continuously.

8.3.3. Press desired device mode key. (e.g. TV)

8.3.4. Press "VOLUME+" key.

8.3.5. Press desired device mode key (e.g. SAT)

8.3.6. The upper 4 red device mode indicators will flash
twice and setting punch through mode will exit if
the setting is activated.

8.3.7. Example: SAT volume is activated on TV mode.

2423

8.4. To deactivate the Punch through Volume
setting:

8.4.1. Hold down "CHANNEL+" and "VOLUME-"
keys on the remote simultaneously for 2 seconds
until the upper 4 red device mode indicators light
up (TV, DVD, SAT, VCR) The lower clear
function keys will also be lit and you will hear 2
beep tones.

8.4.2. Enter the punch through code "1", "1", "1", "0".
The upper 4 red device mode indicators (TV, DVD,
SAT, VCR) flash once and stay lit continuously.
The lower clear function keys will also be lit.

8.4.3. Press desired device mode key. (e.g. TV)

8.4.4. Press "VOLUME-" key.

8.4.5. The upper 4 red device mode indicators will flash
twice and setting punch through mode will exit if
the setting is deactivated.

8.4.6. Example: Punch through volume is deactivated in
TV device mode.

Note:

Setting volume in punch through mode will activate the
"VOLUME+", "VOLUME-" and "MUTE" keys.

9. MACRO POWER

The Macro Power allows you to turn a second device on
or off at the same time. Follow the steps below to activate
this function.

9.1. To activate the Macro Power setting:

9.1.1. Hold down "CHANNEL+" and "VOLUME-"
keys on the remote simultaneously for 2 seconds
until the upper 4 red device mode indicators light
up (TV, DVD, SAT, VCR) The lower clear
function keys will also be lit and you will hear 2
beep tones.

9.1.2. Enter the macro power code "1", "1", "2", "0". The
upper 4 red device mode indicators (TV, DVD,
SAT, VCR) will flash once and then stay lit
continuously. The lower clear function keys will
remain lit.

9.1.3. Press desired device mode key. (e.g. TV)

9.1.4. Press desired device mode key. (e.g. SAT)

9.1.5. The upper 4 red device mode indicators will flash
twice and setting Macro power mode will exit if
the setting is activated.

9.1.6. Example: SAT Macro power is activated on TV
mode.

2625

9.2. To deactivate the Macro Power setting:

9.2.1. Hold down "CHANNEL+" and "VOLUME-"
keys on the remote simultaneously for 2 seconds
until the upper 4 red device mode indicators light
up (TV, DVD, SAT, VCR) The lower clear
function keys will also be lit and you will hear 2
beep tones.

9.2.2. Enter "1", "1", "2", "0" Macro power code. The
upper 4 red device mode indicators (TV, DVD,
SAT, VCR) will flash once and then stay lit
continuously. The clear lower function keys will
also be lit.

9.2.3. Press desired device mode key. (e.g. TV)

9.2.4. Press " " key.

9.2.5. Device mode indicators will flash twice and
setting Macro power mode will exit if the setting
is activated.

9.2.6. Example: Macro power is deactivated on TV
device mode.

10. PROGRAM SMART KEYS

You can program a sequence of steps into your LR such
as turn on your TV, turn on your DVD player, turn on
your home theater receiver and press play on your DVD
player to watch a movie. All in sequence. You can also
program a time delay in the sequence. Each smart key
can program up to 20 steps. Please refer to the following
procedure.

10.1. Hold down "CHANNEL+" and "VOLUME-"
keys on the remote simultaneously for 2 seconds
until the upper 4 red device mode indicators light
up (TV, DVD, SAT, VCR) The lower clear
function keys will also be lit and you will hear 2
beep tones.

10.2. Enter the smart code "0", "0", "0", "9". The upper
4 red device mode indicators (TV, DVD, SAT,
VCR) will flash once and then stay lit
continuously. The lower clear function keys will
also be lit.

10.3. Press desired Smart key. (e.g. SMART 1)

10.4. Press a command from the corresponding device
mode and the upper 4 red device mode indicators
will flash once each time you can press a key.

10.5. Press and hold the command if you want to setup
the transmission period of this command (MAX
delay is 60 seconds)

10.6. Repeat 10.4 to 10.5 until you finish the whole
program and press the same SMART key (e.g.
SMART 1) to store the program.

10.7. To program another smart, repeat 10.1 to 10.6
above.

Note:

- The LR comes with 6 SMART programs (SMART 1,

SMART 2, SMART 3, SHIFT + SMART 1, SHIFT

+ SMART 2, SHIFT + SMART 3) each with a
maximum of 20 steps.

- On step 10.4, if 20 steps have been entered, the setup

is saved automatically. Your LR will exit the smart
key programming mode.

27

- On step 10.4, if no key is selected for more than 8
seconds, the upper 4 red device mode indicators will
flash six times then all device mode indicators turn
off except the selected device mode key and the smart
key programming mode will exit automatically.

- To operate a programmed smart key sequence, aim
your LR at the equipment. Press and release the
SMART key or shift plus smart key you have
programmed.

11. RESET TO FACTORY DEFAULT

11.1. Hold down "CHANNEL+" and "VOLUME-"

keys on the remote simultaneously for 2 seconds
until the upper 4 red device mode indicators light
up (TV, DVD, SAT, VCR) The lower clear
function keys will also be lit and you will hear 2
beep tones.

11.2. Enter the reset code "9", "9", "9", "9". The upper 4

red device mode indicators (TV, DVD, SAT, VCR)
turn off and the selected device indicator will
remain lit. All settings are now cleared to factory
default setting.
If your remote control is locked up for any reason,
you can reset it by disconnecting the battery pack,
wait for 30seconds and re-connect the battery pack
to the remote unit.

12. MAINTENANCE

- Do not expose your LR to dust, strong sunlight,

humidity, high temperature or mechanical shock.

- Be sure to use only the rechargeable nickel metal-

hydride (Ni-MH) battery pack that is supplied
with the remote controller.

- Do not use corrosive or abrasive cleaners on your

LR.

- Keep the unit dust free by wiping it with a soft dry

cloth.

- Do not disassemble your LR; it contains no user-

serviceable parts.

11.3.

28

One Year Limited Warranty:

Elexa Consumer Products, Inc. ("ECP") warrants to the
original retail purchaser ("Purchaser") that the La Z

TM

Boy Home Theater Touch sensitive Remote control
LZ6220 (the "Product") will be free of defects in
materials or workmanship under normal use for one (1)
year from the date of purchase (the "Warranty Period").
For the Purchaser only, if the Product fails to perform as
specified during the Warranty Period due to defective
parts or faulty workmanship, ECP will repair or replace
the defective or damaged parts of the Product. Normal
wear and tear is not covered, nor is abnormal use, misuse,
mishandling, faulty installation, improper shipping,
damage caused by disasters such as fire, flood or
earthquake, neglect, accident or tampering. This
warranty covers only normal use in the United States and
Canada.

To obtain warranty service during the Warranty Period,
contact ECP Customer Service by telephone [phone]-

1459 between the hours of 12am and 11:59pm, or email
[e-mail] for instructions on

sending damaged parts and documentation and for a
Return Material Authorization number (RMA). Products
returned to ECP for repair or replacement without
authorization will be returned to you at your expense.
All warranty claims must be accompanied by a legible
copy of the original receipt showing date and particulars
of purchase. The RMA number must be clearly written
on the side of the shipping container in which you return
the Product or defective parts. Unless otherwise
instructed by us, the Product must be sent freight prepaid
to the following address:

Elexa Consumer Products, 6200 N. Hiawatha Ave,
Chicago IL 60646

30

13. TROUBLESHOOTING

Q. My LR does not work at all!

A. Check your A/V device, if the device's main switch is turned off,

your LR can not operate your device.

A.

A. Check whether you have pressed the corresponding device mode

key for your device.

Q. If several Device Codes are listed under the brand of my A/V

device, how can I select the correct Device Code?

A. To seek the correct Device Code for you're A/V device, test the

code one by one until most keys work properly.

Q. My A/V equipment responds to only some of the commands.

A. You have set a code for which only some commands work properly

but some do not. Try other codes until most keys work properly or
go through the "By searching through the library" in section 3. Or
you may learn the functions from the original remote control
(Please refer to section 4).

Q. My combo device i.e. VCR/DVD can not be programmed using

the codes provided.

A. Try programming the devices individually i.e. first your VCR with

the VCR codes from the code list and then the DVD with the DVD
Codes from the code list. Or you can teach the LR by learning the
functions from the original remote control.

Q. I do not hear the beep tones when pressing keys on my remote.

A. You may have the keypad set to mute. Follow the steps in section

7.6.

Q. Some function keys on the remote do not operate your device.

A. Make sure the LR is set to the correct mode (ie TV)
A.

Q. I am having difficulty accessing the online programming

feature.

A. Make sure the internet connection is active
A. Make sure your LR is connected to your computer through the

USB cord provided

A. Make sure your computer meets the following system

requirements:
IBM compatible with windows 98SE, 2000, ME, XP, Vista.

For help with set up call 1-888-229-1459 or visit
www.lazboyremotes.com for an on-line tutorial.

Check if your battery pack is connected properly and has been
charged for 12 hours.. For details, please refer to section 1.

You can also set up the Remote unit by
inputting the AV device model number from your computer by
downloading the software interface. Please refer to section 6.

The remote may not contain the code for your device. Try learning
the codes you need from your original equipment remote. Follow
the steps in section 4.

Q. My LR is locked up. No keys work when I press them.

A. You can reset your LR by disconnecting your battery pack, wait for

30 seconds and reconnect the battery pack.

29