LAZBOY LZ6100 Installation Manual

Download

Page 1

100 x 190mm Front

Comfort. It's what we do.

Mega Universal Remote Control

Model LZ6100

8 Function Universal Remote Control With

Extra Large Function Keys & Graphics

Installation Guide

PRODUCT DIAGRAM

11 12

Page 2

100 x 190mm

11. Use shift then "7" to access "subtitle" / "closed caption".

12. Use shift then "9" to access "info" and to "select" when in guide or menu mode.

13. Use shift then "8" to access the toggle function from PIP back to normal picture.

14. Exits on screen menus, guides and returns you to the previous on screen selection.

15. Brings up the menu screen. Use shift then , , , , keys to scroll, use shift then menu to access PIP.

16. Rewind when in VCR mode, scan back when in DVD, CD & DVR mode. Use shift then to scroll left thru menus and guides.

17. Fast forward when in VCR mode. Scan forward when in DVD, CD & DVR mode. Use shift and to scroll right thru menus and guides.

18. Access the play feature when in VCR, DVD mode. Use shift then to scroll up through menus and guides.

19. Stop key when in VCR, DVD, CD & DVR mode. Use shift then to access the OK function when scrolling through menus and guides.

20. Pause when in VCR, DVD, CD & DVR mode.

21. Record when in VCR DVR & DVD mode. Use the shift then to access guide when in SAT or Cable mode.

KEY FUNCTION DESCRIPTIONS

1. Programs your VCR. Also programs one auxiliary device using the shift key.

2. Programs your TV. Also programs one auxiliary device using the shift key.

3. Power key- Turns device for remote's current mode on or off.

4. Programs your satellite receiver. Also programs one auxiliary device using the shift key.

5. Programs your DVD player. Also programs one auxiliary device using the shift key.

6. Allows you to program auxiliary devices 1-4 or allows you to access secondary functions of certain devices.

7. Changes the channels when in TV, DVR, satellite or cable mode. Scrolls through chapters when in DVD mode or tracks when in CD mode.

8. Changes the volume level of the device. Normally used when in TV mode.

9. Allows you to return to the previously selected channel in TV, Sat or Cable mode. Also allows you to control the input source when in TV mode. Press the shift key and the source key to toggle.

10. Allows you to turn the volume on or off when in TV mode.

Page 3

100 x 190mm

Table of Contents

Product Diagram Page 1

Key Function Descriptions Page 2 - 3

Introduction/Package Contents Page 4

Getting Started Page 6

Battery Installation & Information Page 7

How to set up your La-z-boy remote Page 8 - 9

o By code entry o By code search

Maintenance Page 16

Troubleshooting Page 17

Warranty Page 18

Congratulations on the purchase of your La-Z-Boy Universal Remote Control, a state of the art product which integrates several infra-red devices to deliver complete A/V control at the tip of your fingers.

Before operating your remote please read through this manual carefully and save it for future reference.

This package contains the following:

- One LZ6100 Mega Universal Remote Control.

- One Installation Guide.

- One Quick Reference Guide.

- One Infra-red Device Code List.

- A blank device sticker (To be placed on the battery

door).

La-Z-Boy has evolved throughout their 75 year history to become America's Number 1 furniture brand.

The new line of La-Z-Boy Universal Remote Controls represents the perfect marriage of relaxation, comfort, ease of use, quality and convenience when watching television in your favorite La-Z-boy!

The La-Z-Boy Difference:

- Bilingual Consumer hotline available 24 hours/day,

7 days/week.

- Easy to follow quick reference guide.

- Comfortable rubber grips.

- On-line Tutorial.

Page 4

100 x 190mm

1. HOW TO INSTALL BATTERIES

La-z-boy recommends the use of alkaline batteries in our remotes for longest battery expectancy. The number of batteries required is stated on the back of the coversheet.

1. Remove the battery cover on the back of your La-Z-Boy remote (LR).

2. Check the polarity of the batteries and the "+/-" marks inside the battery compartment.

3. Insert the batteries.

4. Push the battery cover back in place.

Battery Low

If the indicator flashes twice slowly after using the LR, it shows that the battery level is low. You must replace them with new batteries to ensure proper functioning.

Note: 4 AAA batteries required (not included).

GETTING STARTED

A few helpful hints on terms used in this manual.

LR:

La-Z-Boy Universal Remote Control.

LED:

The red indicator light that flashes with an infra-red command to your equipment.

Backlighting:

The blue backlighting on the keypad of your La-z-boy remote. Backlighting turns on each time a key is pressed and will turn off 8 seconds after the last key is released.

Battery Low:

If the red LED indicator flashes twice after activating any command, it shows that the battery level is low. You must replace the batteries with new batteries to ensure proper functioning of your remote.

Note: When replacing batteries you have approximately 5 mins before your programmed codes are lost. All factory program codes will remain in memory permanently.

Shift:

The shift key allows you to access secondary functions

th th

of the remote and to operate the 5 thru the 8 device (AUX 1-4). Please follow the instructions in this manual.

Page 5

100 x 190mm

Suggestion:

- If you cannot find a correct Device Code for your equipment, refer to the section that follows: How To Set Up The LR By Searching Through the Library.

- For future reference it is recommended to make a note of your Device Codes in the space provided on the back label after setting up your LR correctly.

By Searching Through the Library

If you cannot identify a correct Device Code for your equipment from the Device Code list, you may search through the code library:-

1. Turn on your device manually (e.g. TV).

2. Press a desired Device Mode Key (e.g. TV). The red LED indicator will blink once.

3. Hold down "CHANNEL +" and "VOLUME -" on the LR together simultaneously for 2 seconds until the red LED indicator lights continuously.

4. Enter a corresponding Search Code from following table. The indicator should go out immediately.

(e.g. press TV device mode key, then press "CHANNEL +" and "VOLUME -", and enter The TV Search Code 0001.)

5. Press the same desired device mode key again as in step 2 above. (e.g. TV)

6. Hold down "CHANNEL +" and "VOLUME -" together simultaneously again for 2 seconds until the red LED indicator lights continuously. LR is ready to start searching.

2. HOW TO SET UP YOUR LA-Z-BOY REMOTE (LR)

By Entering Device Code

You may setup your La-Z-Boy Remote (LR) by the following code entering instructions.

1. Turn on your device (e.g. TV).

2. Refer to the DEVICE CODE LIST; look up the 4-

digit Device Code which corresponds to the brands of your A/V equipment. If there are more than one Device Code listed under your brand, try from the first code.

3. Press a desired Device Mode Key (e.g. TV). The red

LED indicator will blink once.

4. Hold down "CHANNEL +" and "VOLUME -" on

the LR simultaneously for 2 seconds until the red LED indicator lights continuously.

5. Use the number keys 0-9 to enter your 4-digit Device

Code. The red LED indicator should go out

immediately. Then try the function keys (e.g. TV) on the LR. If your device (e.g. TV) responds to your activated function correctly, you have entered the right Device Code. Otherwise, repeat the above setup with the next available Device Code until your device (e.g. TV) responds to your activated function, and most keys work correctly.

* Simply repeat the above procedures to enter the

Device Codes for your VCR, SAT, DVD and other

Devices. (Remember to press a correct Device Mode

Key in step 2 above). For set up of Auxiliary devices

(AUX 1-4) press "SHIFT" followed by the desired

device key (AUX 1-4) then follow steps 4-5 above.

Note:

If the indicator flashes twice in step 5, a wrong Device Code has been entered. You are required to repeat step 3 to 5 again.

DEVICE TYPE:

SEARCH CODE:

0001

VCR

0002

SAT

0003

CABLE

0004

DVD

0005

AUDIO

0006CD0007

HOME

THEATER

0008

Page 6

100 x 190mm

Important:

When searching through the Library for some older devices, if the power on/off function of your device is not infra-red controlled you need to follow steps 2 to 6 above and start searching:-

- Press " " (power) key and another important function key alternately until your device responds to the expected function, press the same device mode key (e.g. TV) to lock in the code.

- Press " " (power) key & "Channel +" alternately, or;

- Press " " (power) key & "1" alternately.

Note:

- Each time you press the " " (power) key, the LR will skip to the next code and send out a POWER signal trying to turn off your device.

- If you failed to stop pressing " " (power) key in time when your device has been turned off, turn on your device again immediately. Before the indicator goes out, press " " on the LR to skip backward. Repeat the step 7 above and lock in the code.

- If the red LED indicator flashes twice after you pressed the " " (power) key, you are already at the last code of the library.

- Besides device keys, " " (power) key and " " (mute) key, all keys can be operated if the remote has entered search mode.

7. Aim the LR at your device (e.g. TV); press the " " (power) key repeatedly every 1-2 seconds until the device has been turned off. The red LED indicator will blink once each time you press the " " (power) key to indicate your remote is scrolling thru the code library. Once your device has been turned off, immediately press the same device mode key (e.g. TV) to lock in the search code and the red LED indicator should go out.

* Simply repeat the above setup procedures to search

the Device Code for your VCR, SAT, DVD and other Devices. (Remember to press a correct Device Mode Key and correct Search Code in step 2-5 above).

* For set up of Auxiliary devices (AUX 1-4) press

"SHIFT" followed by the desired device key (AUX 1-4) then follow steps 3-7 above.

Note: The search process can take several minutes due to the number of codes stored in the library.

Note:

You cannot search through the code library for DVR devices.

Important: During set up mode, the red LED indicator will blink twice and the set up procedure will be terminated if any of the following conditions occur;

- No key has been pressed for more than 8 seconds.

- An invalid code number has been entered.

- An invalid key (not a numeric key) has been pressed.

1110

Page 7

100 x 190mm

4. PUNCH THROUGH

You can activate certain functions like TV volume to be operated in other modes such as SAT. This is referred to as Punch Through please refer to the following procedure for activating this function.

4.1 To activate the Punch through Channel setting:

4.1.1. Press desired Device Mode Key (e.g. TV). The red LED indicator will blink once.

4.1.2. Press and Hold "CHANNEL +" key.

4.1.3. Press the desired Device Mode Key in which you want to change the channel for (e.g. SAT).

4.1.4. Release "CHANNEL +" (LED flashes once if the setting is activated).

4.2 To deactivate the Punch through Channel setting:

4.2.1. Press desired Device Mode Key (e.g. TV). The red LED indicator will blink once.

4.2.2. Press and Hold "CHANNEL -" key.

4.2.3. Press the Desired Mode Key in which you want to change the channel for (e.g. SAT).

4.2.4. Release "CHANNEL -" (LED flashes twice if the setting is deactivated).

3. OPERATING THE LA-Z-BOY REMOTE (LR)

Normal Operation

1. Once you have setup up the LR for your A/V

equipment, it works like the original remote control. To operate, just aim it at your equipment, press an appropriate device mode key and invoke the desired function by pressing a corresponding key on the LR. The indicator flashes during signal transmission and as confirmation of key touch.

2. Use the shift button when attempting to access

auxiliary devices (AUX 1-4) or when attempting to access secondary functions please refer to the Key Function Description on Page 2.

Note:

On step 4.1.3 or 4.2.3 if desired device is an auxiliary device press (SHIFT) then the desired Auxiliary key (AUX 1-4).

- Press "SHIFT" key before step 4.1.3 or 4.2.3, LED will flash twice.

- Release "SHIFT" key, LED will turn ON continuously.

- Continue Step 4.1.4 or 4.2.4.

1312

Page 8

100 x 190mm

5. MACRO POWER

The Macro Power allows you to turn a second device on or off at the same time. Follow the steps below to activate this function.

5.1 To activate the Macro Power setting:

5.1.1. Press desired Device Mode Key (e.g. TV). The red LED indicator will blink once.

5.1.2. Press and Hold (power) key.

5.1.3. Press desired Device Mode Key (e.g. SAT).

5.1.4. Release (power) key (LED will flash once if the setting is activated).

5.2 To deactivate the Macro Power setting:

5.2.1. Press desired Device Mode Key (e.g. TV). The red LED indicator will blink once.

5.2.2. Press and Hold (power) key.

5.2.3. Press desired SAT Device Mode Key (e.g. SAT).

5.2.4. Release (power) key (LED flashes twice if the setting is deactivated).

" "

4.3 To activate the Punch through Volume setting:

4.3.1. Press desired Device Mode Key (e.g. TV). The red LED indicator will blink once.

4.3.2. Press and Hold "VOLUME +"key.

4.3.3. Press desired Device Mode Key in which you want to change the channel for (e.g. SAT).

4.3.4. Release "VOLUME +" (LED flashes once if the setting is activated).

4.4 To deactivate the Punch through Volume setting:

4.4.1. Press desired Device Mode Key (e.g. TV). The red LED indicator will blink once.

4.4.2. Press and Hold "VOLUME -" key.

4.4.3. Press desired Device Mode Key in which you want to change the channel for (e.g. SAT).

4.4.4. Release "VOLUME -" (LED flashes twice if the setting is deactivated).

Note:

On step 4.3.3 or 4.4.3 if desired device is an auxiliary device press (SHIFT) then the desired Auxiliary key (AUX 1-4).

- Press "SHIFT" key before step 4.3.3 or 4.4.3, LED will flash once.

- Release "SHIFT" key, LED will turn ON continuously.

- Continue Step 4.3.4 or 4.4.4.

Note:

On step 5.1.3 or 5.2.3 if desired if desired device is an auxiliary device press (SHIFT) then the desired Auxiliary key (AUX 1-4).

- Press "SHIFT" key before step 5.1.3 or 5.2.3, LED will flash twice.

- Release "SHIFT" key, LED will turn ON continuously.

1514

Page 9

100 x 190mm

7. TROUBLESHOOTING

Q. My LR does not work at all! A. Check your A/V device, if the device's main switch is

turned off, your LR can not operate your device.

A. Check if your batteries are inserted properly in

correct +/- positioning.

A. Check whether you have pressed the corresponding

device mode key for your device.

A. If the battery level is low, replace the batteries

Note: When replacing the batteries, you have approximately 5 mins before your programmed codes are lost.

Q. If several Device Codes are listed under the brand of

my A/V device, how can I select the correct Device Code?

A. To seek the correct Device Code for you're A/V

device, test the code one by one until most keys work properly.

Q. My A/V equipment responds to only some of the

commands.

A. You have set a code for which only some commands

work properly but some do not. Try other codes until most keys work properly.

Q. My combo device i.e. VCR/DVD can not be

programmed using the codes provided.

A. Try programming the devices individually i.e. first

your VCR with the VCR codes from the code list and then the DVD with the DVD Codes from the code list.

For help with set up call 1-888-229-1459 or visit www.lazboyremotes.com for an on-line tutorial.

6. MAINTENANCE

- Do not expose your LR to dust, strong sunlight, humidity, high temperature or mechanical shock.

- Do not use old and new batteries together as old batteries tend to leak.

- Do not use corrosive or abrasive cleaners on your LR. Keep the unit dust free by wiping it with a soft dry cloth.

- Do not disassemble your LR, it contains no userserviceable parts.

1716

Page 10

100 x 190mm

ECP will repair or replace the defective parts and return them at ECP's cost by a shipping method selected by ECP. When contacting ECP to obtain an RMA, Purchaser may request expedited return shipping at Purchaser's cost.

THIS WARRANTY IS NOT TRANSFERABLE, AND, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IS IN LIEU OF ALL OTHER WARRANTIES, REPRESENTATIONS AND CONDITIONS, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NO OTHER PERSON OR REPRESENTATIVE IS AUTHORIZED TO MAKE ANY OTHER WARRANTY ON BEHALF OF ECP OR ASSUME FOR ECP ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. IN NO EVENT WILL ECP BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT, INCLUDING DAMAGES DUE TO ECP'S NEGLIGENCE.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE AND COUNTRY TO COUNTRY.

One Year Limited Warranty:

Elexa Consumer Products, Inc. ("ECP") warrants to the original retail purchaser ("Purchaser") that the La Z

Boy Home Theater Series Mega Universal Remote LZ6100 (the "Product") will be free of defects in materials or workmanship under normal use for one (1) year from the date of purchase (the "Warranty Period"). For the Purchaser only, if the Product fails to perform as specified during the Warranty Period due to defective parts or faulty workmanship, ECP will repair or replace the defective or damaged parts of the Product. Normal wear and tear is not covered, nor is abnormal use, misuse, mishandling, faulty installation, improper shipping, damage caused by disasters such as fire, flood or earthquake, neglect, accident or tampering. This warranty covers only normal use in the United States and Canada.

To obtain warranty service during the Warranty Period, contact ECP Customer Service by telephone 1-888-229-

1459 between the hours of 12am and 11:59pm, or email customersupport@elexausa.com for instructions on

sending damaged parts and documentation and for a Return Material Authorization number (RMA). Products returned to ECP for repair or replacement without authorization will be returned to you at your expense. All warranty claims must be accompanied by a legible copy of the original receipt showing date and particulars of purchase. The RMA number must be clearly written on the side of the shipping container in which you return the Product or defective parts. Unless otherwise instructed by us, the Product must be sent freight prepaid to the following address:

Elexa Consumer Products, 6200 N. Hiawatha Ave, Chicago IL 60646

F820-7330-0000

Back

1918

Page 11