Lancom WLC-1000 User Manual

LANCOM

Installation Guide

LANCOM Installation Guide – Copyright

Copyright

While the information in this manual has been compiled with great care, it may not be

deemed an assurance of product characteristics. LANCOM Systems shall be liable only to the

degree speciﬁed in the terms of sale and delivery.

The reproduction and distribution of the documentation and software supplied with this

product and the use of its contents is subject to written authorization from LANCOM Systems.

We reserve the right to make any alterations that arise as the result of technical development.

Windows® and Microsoft® are registered trademarks of Microsoft, Corp.

The LANCOM Systems logo, LCOS and the name LANCOM are registered trademarks of

LANCOM Systems GmbH. All other names or descriptions used may be trademarks or registe-

red trademarks of their owners.

Subject to change without notice. No liability for technical errors or omissions.

Products from LANCOM Systems include software developed by the “OpenSSL Project” for

use in the “OpenSSL Toolkit” (www.openssl.org).

Products from LANCOM Systems include cryptographic software written by Eric Young (eay@

cryptsoft.com).

Products from LANCOM Systems include software developed by the NetBSD Foundation, Inc.

and its contributors.

Products from LANCOM Systems contain the LZMA SDK developed by Igor Pavlov.

LANCOM Systems GmbH

Adenauerstr. 20/B2

52146 Wuerselen

Germany

www.lancom-systems.com

Wuerselen, April 2018

LANCOM Installation Guide – Introduction

Introduction

Thank you for purchasing an LCOS-based LANCOM device.

This installation guide describes how to put your LANCOM device into

operation and its initial setup.

Installation includes:

A Positioning and mounting A Safety advice

The initial setup includes:

A Conﬁguration via LANconﬁg

LANconﬁg is the free-of-charge and user-friendly software for the

conﬁguration of LANCOM devices on Microsoft Windows. LANconﬁg

has a huge spectrum of applications, from the user-friendly commis-

sioning of a single device with installation wizards to the comprehen-

sive management of large-scale installations.

You can ﬁnd the download free of charge at:

www.lancom-systems.com/downloads/

A Conﬁguration via WEBconﬁg

WEBconﬁg is the browser-based conﬁguration user interface that is

available on the LANCOM device and can be used on any operating

system.

A Conﬁguration via the LANCOM Management Cloud

The LANCOM Management Cloud is the management system that

intelligently organizes, optimizes, and controls your entire network

architecture. (licence and working Internet access required)

You can ﬁnd out more about the LANCOM Management Cloud at:

www.lancom-systems.com/lmc/

The document continues with further information about operating the

device, the documentation, and LANCOM Service & Support.

LANCOM Installation Guide – Installation

Installation

For safe and secure installation of your LANCOM device, please observe

the safety instructions and the instructions for positioning and mounting.

Positioning and mounting

Please observe the instructions for the positioning and mounting of the

device in the Quick Reference Guide.

In order to avoid damage, note the temperature range given in the Quick

Reference Guide. Further, ensure there is adequate ventilation and do not

place the device in direct sunlight.

Antennas are only to be attached or exchanged while the device is switched

off. Mounting or demounting antennas while the device is switched on

may cause the destruction of the radio module! When installing outdoor

antennas, the instructions on installation and grounding in the LANCOM

Outdoor Wireless Guide must be observed.

Notes on the individual interfaces, switches and displays on your device are

available in the supplied Quick Reference Guide.

Safety advice

This section contains notices which should be observed to avoid injury to

persons or damage to your device.

Proper usage

Operate the device only as described in the accompanying documen-

tation. Pay particular attention to all warnings and safety instructions. Use

LANCOM Installation Guide – Installation

only those third-party devices and components that are recommended or

approved by the manufacturer.

Power supply

Please make sure to use only the power adapter listed in the Quick

Reference Guide. The use of the incorrect power adapter can be a

hazard to the device or persons. The Quick Reference Guide is shipped

with your device. Alternatively it can be downloaded from the LANCOM

website (www.lancom-systems.com). Some models can be powered via

the Ethernet cable (Power-over-Ethernet, PoE). Please observe the relevant

notes in the Quick Reference Guide for the device.

General safety

This device is powered by electricity. Adhere strictly to the safety require-

ments outlined in the documentation with regard to the voltages to be

applied. Never operate damaged components. Turn a device on only if the

housing is closed.

Opening the housing is reserved exclusively for the manufacturer’s autho-

rized technicians. Never insert pointed objects (thin screwdrivers, wires,

etc.) into the product’s interior. Risk from electric shock!

Any work required for the electrical installation must be carried out by a

trained electrician.

Make sure that the electrical installation complies with local or national

safety requirements.

LANCOM Installation Guide – Initial Setup

Initial setup

A LANCOM device can be conﬁgured conveniently by TCP/IP. The following

conﬁguration paths are available for this:

A LANconﬁg A WEBconﬁg A LANCOM Management Cloud

For devices with a serial interface, the conﬁguration can be

conducted with LANconﬁg or a terminal program.

Conﬁguration via LANconﬁg

Unconﬁgured LANCOM devices in local networks (LAN) are detected

automatically. It is very easy to search the LAN for new devices. Click the

button Search now.

In the dialog box that follows, you further specify the settings for the

device search.

+ 11 hidden pages