Page 1
LANCOM R&S®UF-50
4
Quick Reference Guide
4
Power connector
a
After connecting the power supply cable to the device, turn
the screwcap clockwise to prevent the jack from accidental
un plugging. Use only the supplied power adapter.
Power button
b
Press the power button to start up the device.
To power off the device, press the power button for 5 seconds.
USB 2.0 interfaces
c
Interfaces for device software re-installation
12V
USB
Power
Console
eth0
eth1
ba c d e
Serial conguration interface RJ45 (Console)
d
Maintenance interface for expert conguration
TP Ethernet interfaces eth0 - eth3
e
Connect one of the eth0 - eth3 TP Ethernet interfaces with
the enclosed Ethernet cable to your conguration PC or other
networking components. Initial setup advice can be found in
the supplied quick install guide.
Reset button
f
Short press - device restart
eth2
eth3
Reset
f
Hardware
Power supply 12 V DC, external power supply
Power consumption 36 W
Environment Temperature range 0–40 °C; humidity 10–90 %; non-condensing
Housing Robust metal housing, network connectors on the front
Dimensions (mm) 225 x 44 x 150 (W x H x D)
Interfaces
eth0
b
eth1
d
eth2
eth3
Reset
ETH 4x 10 / 100 / 1000 Mbps Gigabit Ethernet ports
USB 2x USB 2.0 ports
Console RJ45 conguration interface
Declaration of conformity
Hereby, LANCOM Systems declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, and
2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address:
www.lancom-systems.com/ce/
Package content
Documentation Quick Reference Guide (DE, EN), Quick Install Guide (DE/EN), Service & Support Guide (DE/EN)
Accessories 1 Ethernet cable; 1 power supply unit with IEC power cable; 1 serial conguration cable;
1 set adhesive rubber pads
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may
be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes.
LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions. 111860/1119
a
a LEDs eth0 - eth3 - TP Ethernet
Both off No networking device attached
Upper green, ickering
Lower orange,
permanently
Upper green, ickering
Lower off
Data transfer 1000 / 100 Mbps
Data transfer 10 Mbps
12V
Power
b LEDs Power / HDD
Power off Device switched off
Power green Device operational
HDD off No HDD read-/write access
HDD orange, ickering HDD read-/write access
USB
Console
c
Please observe the following when setting up the device
A The mains plug of the device must be freely accessible.
A For devices to be operated on the desktop, please attach the adhesive rubber
footpads.
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
A Do not rest any objects on top of the device and do not stack multiple devices.
A Keep all ventilation slots of the device clear of obstruction.
c LED Power switch
Off No power supply connected
Red, permanently Device switched off, power supply
connected
Blue, permanently Device switched on
MOUNTING AND CONNECTING THE DEVICE
d LEDs eth0 - eth3 - TP Ethernet
Both off Gerät ausgeschaltet oder
Left green, ickering
Right green,
permanently
Left green, ickering
Right orange,
permanently
Left green, ickering
Right off
kein Netzwerkgerät angeschlossen
Data transfer 1000 Mbps
Data transfer 100 Mbps
Data transfer 10 Mbps
TECHNICAL DATA
Loading...